When detaching a buffer from a vq, the avail.idx value should be
decremented as well.
This was noticed by hot-unplugging a virtio console port and then
plugging in a new one on the same number (re-using the vqs which were
just 'disowned'). qemu reported
'Guest moved used index from 0 to 256'
when any IO was attempted on the new port.
CC: stable@kernel.org
Reported-by: juzhang <juzhang@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Intel VT-d Protected Memory Regions (PMRs) are supposed to be disabled,
on each VT-d engine, after DMA remapping is enabled on the engines.
This is because the behavior of having both enabled is not deterministic
and because, if TXT has been used to launch the kernel, the PMRs may be
programmed to cover memory regions that will be used for DMA.
Under some circumstances (certain quirks detected, lack of multiple
devices, etc.), the current code does not set up DMA remapping on some
VT-d engines. In such cases it also skips disabling the PMRs. This
causes failures when the kernel is launched with TXT (most often this
occurs on the graphics engine and results in colored vertical bars on
the display).
This patch detects when the kernel has been launched with TXT and then
disables the PMRs on all VT-d engines. In some cases where the reason
that remapping is not being enabled is due to possible ACPI DMAR table
errors, the VT-d engine addresses may not be correct and thus not able
to be safely programmed even to disable PMRs. Because part of the TXT
launch process is the verification of these addresses, it will always be
safe to disable PMRs if the TXT launch has succeeded and hence only
doing this in such cases.
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch removes superfluous debugging output in the sysfs scrub rate
handler. It also consolidates the error handling in the scrub rate
accessors.
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
pg_start is copied from userspace on AGPIOC_BIND and AGPIOC_UNBIND ioctl
cmds of agp_ioctl() and passed to agpioc_bind_wrap(). As said in the
comment, (pg_start + mem->page_count) may wrap in case of AGPIOC_BIND,
and it is not checked at all in case of AGPIOC_UNBIND. As a result, user
with sufficient privileges (usually "video" group) may generate either
local DoS or privilege escalation.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
page_count is copied from userspace. agp_allocate_memory() tries to
check whether this number is too big, but doesn't take into account the
wrap case. Also agp_create_user_memory() doesn't check whether
alloc_size is calculated from num_agp_pages variable without overflow.
This may lead to allocation of too small buffer with following buffer
overflow.
Another problem in agp code is not addressed in the patch - kernel memory
exhaustion (AGPIOC_RESERVE and AGPIOC_ALLOCATE ioctls). It is not checked
whether requested pid is a pid of the caller (no check in agpioc_reserve_wrap()).
Each allocation is limited to 16KB, though, there is no per-process limit.
This might lead to OOM situation, which is not even solved in case of the
caller death by OOM killer - the memory is allocated for another (faked) process.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://neil.brown.name/md:
md: Update documentation for sync_min and sync_max entries
md: Cleanup after raid45->raid0 takeover
md: Fix dev_sectors on takeover from raid0 to raid4/5
md/raid5: remove setting of ->queue_lock
Since
commit a120e912eb
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Feb 19 15:47:33 2010 -0800
iwlwifi: sanity check before counting number of tfds can be free
we use skb->data after calling ieee80211_tx_status_irqsafe(), which
could free skb instantly.
On current kernels I do not observe practical problems related with
bug, but on 2.6.35.y it cause random system hangs when stressing
wireless link, making bisection of other problems impossible.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since
commit a120e912eb
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Feb 19 15:47:33 2010 -0800
iwlwifi: sanity check before counting number of tfds can be free
we use skb->data after calling ieee80211_tx_status_irqsafe(), which
could free skb instantly.
On current kernels I do not observe practical problems related with
bug, but on 2.6.35.y it cause random system hangs when stressing
wireless link.
Cc: stable@kernel.org # 2.6.32+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Remove the extra check in queue_requests_store
block, blk-sysfs: Fix an err return path in blk_register_queue()
block: remove stale kerneldoc member from __blk_run_queue()
block: get rid of QUEUE_FLAG_REENTER
cfq-iosched: read_lock() does not always imply rcu_read_lock()
block: kill blk_flush_plug_list() export
The rtc_device_register() call has changed semantics so that it
will immediately call out to rtc_read_alarm() and since the
callbacks require the drvdata to be set, we need to set it before
the registration call to avoid NULL dereference.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The slave member of struct aggregator does not necessarily point
to a slave which is part of the aggregator. It points to the
slave structure containing the aggregator structure, while
completely different slaves (or no slaves at all) may be part of
the aggregator.
The agg_device_up() function wrongly uses agg->slave to find the state
of the aggregator. Use agg->lag_ports->slave instead. The bug has
been introduced by commit 4cd6fe1c64
("bonding: fix link down handling in 802.3ad mode").
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently continuing if ehea_restart_qps() fails, when we
do a memory DLPAR (remove or add more memory to the system).
This patch just let the NAPI disabled if the ehea_restart_qps()
fails.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When evaluating sense data in dasd_eckd_check_for_device_change, we
must always check for the type of sense data in byte 27, bit 0, to
make sure that the rest of the sense data is interpreted correctly.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The qdio hardware may surpress further interrupts as long as a SBAL is in
the error state. That can lead to unnotified data in the SBALs following
the error state. To prevent this behaviour change the SBAL[s] in error
state immediately to another program owned state so interrupts are again
received for further traffic on the device.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The dasd_open function uses the private_data pointer of the gendisk to
find the dasd_block structure that matches the gendisk. When a DASD
device is set offline, we set the private_data pointer of the gendisk
to NULL and later remove the dasd_block structure, but there is still
a small race window, in which dasd_open could first read a pointer
from the private_data field and then try to use it, after the structure
has already been freed.
To close this race window, we will store a pointer to the dasd_devmap
structure of the base device in the private_data field. The devmap
entries are not deleted, and we already have proper locking and
reference counting in place, so that we can safely get from a devmap
pointer to the dasd_device and dasd_block structures of the device.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Problem:
After raid4->raid0 takeover operation, another takeover operation
(e.g raid0->raid10) results "kernel oops".
Root cause:
Variables 'degraded' in mddev structure is not cleared
on raid45->raid0 takeover.
This patch reset this variable.
Signed-off-by: Krzysztof Wojcik <krzysztof.wojcik@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
A raid0 array doesn't set 'dev_sectors' as each device might
contribute a different number of sectors.
So when converting to a RAID4 or RAID5 we need to set dev_sectors
as they need the number.
We have already verified that in fact all devices do contribute
the same number of sectors, so use that number.
Signed-off-by: NeilBrown <neilb@suse.de>
We previously needed to set ->queue_lock to match the raid5
device_lock so we could safely use queue_flag_* operations (e.g. for
plugging). which test the ->queue_lock is in fact locked.
However that need has completely gone away and is unlikely to come
back to remove this now-pointless setting.
Signed-off-by: NeilBrown <neilb@suse.de>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: pll tweaks for r7xx
drm/nouveau: fix allocation of notifier object
drm/nouveau: fix notifier memory corruption bug
drm/nouveau: fix pinning of notifier block
drm/nouveau: populate ttm_alloced with false, when it's not
drm/nouveau: fix nv30 pcie boards
drm/nouveau: split ramin_lock into two locks, one hardirq safe
drm/radeon/kms: adjust evergreen display watermark setup
drm/radeon/kms: add connectors even if i2c fails
drm/radeon/kms: fix bad shift in atom iio table parser
Problem description:
gsm_queue() calculate a CRC for arrived frames. As a last step of
CRC calculation it call
gsm->fcs = gsm_fcs_add(gsm->fcs, gsm->received_fcs);
This work perfectly for the case of GSM0 mode as gsm->received_fcs
contain the last piece of data required to generate final CRC.
gsm->received_fcs is not used for GSM1 mode. Thus we put an
additional byte to CRC calculation. As result we get a wrong CRC
and reject incoming frame.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If cts changes between reading the level at the cts input (USR1_RTSS)
and acking the irq (USR1_RTSD) the last edge doesn't generate an irq and
uart_handle_cts_change is called with a outdated value for cts.
The race was introduced by commit
ceca629 ([ARM] 2971/1: i.MX uart handle rts irq)
Reported-by: Arwed Springer <Arwed.Springer@de.trumpf.com>
Tested-by: Arwed Springer <Arwed.Springer@de.trumpf.com>
Cc: stable@kernel.org # 2.6.14+
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace release_resource() by release_region() and also fix the
inconsistency in the size of the requested/released region.
The size of the resource should be 32, not 0x8 like it was corrected in
commit e7c310c36e already.
CC: linux-serial@vger.kernel.org
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Niels de Vos <ndevos@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 73412c3854 ("drm/nouveau: allocate
kernel's notifier object at end of block") intended to align end of
notifier block to page boundary, but start of block was miscalculated
to be off by -16 bytes. Fix it.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_bo_wr32 expects offset to be in words, but we pass value in bytes,
so after commit 73412c3854 ("drm/nouveau: allocate
kernel's notifier object at end of block") we started to overwrite some memory
after notifier buffer object (previously m2mf_ntfy was always 0, so it didn't
matter it was a value in bytes).
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Reported-by: Nigel Cunningham <lkml@nigelcunningham.com.au>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Pekka Paalanen <pq@iki.fi>
Cc: stable@kernel.org [2.6.38]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Wasn't aware they even existed, apparently they do! They're actually
AGP chips with a bridge as far as I can tell, which puts them in the
same boat as nv40/nv45.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes a possible lock ordering reversal between context_switch_lock
and ramin_lock.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Device suspend/resume infrastructure is used not only by the suspend
and hibernate code in kernel/power, but also by APM, Xen and the
kexec jump feature. However, commit 40dc166cb5
(PM / Core: Introduce struct syscore_ops for core subsystems PM)
failed to add syscore_suspend() and syscore_resume() calls to that
code, which generally leads to breakage when the features in question
are used.
To fix this problem, add the missing syscore_suspend() and
syscore_resume() calls to arch/x86/kernel/apm_32.c, kernel/kexec.c
and drivers/xen/manage.c.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (51 commits)
netfilter: ipset: Fix the order of listing of sets
ip6_pol_route panic: Do not allow VLAN on loopback
bnx2x: Fix port identification problem
r8169: add Realtek as maintainer.
ip: ip_options_compile() resilient to NULL skb route
bna: fix memory leak during RX path cleanup
bna: fix for clean fw re-initialization
usbnet: Fix up 'FLAG_POINTTOPOINT' and 'FLAG_MULTI_PACKET' overlaps.
iwlegacy: fix tx_power initialization
Revert "tcp: disallow bind() to reuse addr/port"
qlcnic: limit skb frags for non tso packet
net: can: mscan: fix build breakage in mpc5xxx_can
netfilter: ipset: set match and SET target fixes
netfilter: ipset: bitmap:ip,mac type requires "src" for MAC
sctp: fix oops while removed transport still using as retran path
sctp: fix oops when updating retransmit path with DEBUG on
net: Disable NETIF_F_TSO_ECN when TSO is disabled
net: Disable all TSO features when SG is disabled
sfc: Use rmb() to ensure reads occur in order
ieee802154: Remove hacked CFLAGS in net/ieee802154/Makefile
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: pci-label: Fix build failure when CONFIG_NLS is set to 'm' by allmodconfig
The patch 'ath9k_hw: fix stopping rx DMA during resets' added code to detect
a condition where rx DMA was stopped, but the MAC failed to enter the idle
state. This condition requires a hardware reset, however the return value
of ath_stoprecv was 'true' in that case, which allowed it to skip the reset
when issuing a fast channel change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Paul Stewart <pstew@google.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
q->memory entry is initialized to late, so if allocation of memory buffers
fails, the buffers might not be freed correctly (q->memory is tested in
__vb2_free_mem, which can be called before setting q->memory).
Reported-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Videobuf2 core assumes that driver doesn't set any buffer flags.
This is correct for buffer state flags that videobuf2 manages,
but the other flags like V4L2_BUF_FLAG_{KEY,P,B}FRAME,
V4L2_BUF_FLAG_TIMECODE and V4L2_BUF_FLAG_INPUT should be passed from or to
the driver.
Reported-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for buffer timestamps and the sequence number in
the video capture driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure the sizeimage for 3-planar color formats is
width * height * 3/2 and the bytesperline is same for each
plane in case of a multi-planar format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Protecting the color format with vb2_is_streaming() is not sufficient
as this prevents changing the format only after VIDIOC_STREAMON.
To prevent the color format reconfiguration as soon as buffers
are allocated use vb2_is_busy() instead.
Also make the videobuf queue ops structure static.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correct pixel limits for the fourth FIMC entity on Exynos4 SoCs.
FIMC3 only supports the writeback input from the LCD mixer.
Also rename s5pv310 variant to exynos4 which is needed after
renaming s5pv310 series to Exynos4.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'timer-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: rtc-omap: Fix a leak of the IRQ during init failure
posix clocks: Replace mutex with reader/writer semaphore
This reverts commit 35d9f510b6.
Quoth Jiri Slaby:
"It fixes mmap when IOMMU is used on x86 only, but breaks architectures
like ARM or PPC where virt_to_phys(dma_alloc_coherent) doesn't work.
We need there dma_mmap_coherent or similar (the trickery what
snd_pcm_default_mmap does but in some saner way). But this cannot be
done at this phase."
Requested-by: Jiri Slaby <jslaby@suse.cz>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct pmbus_data included an unused variable named status_bits.
Remove it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
R_MPD bit 3 does not depend on analog vs. digital. Just use
(0x7f & pd) directly from the values in the main pll table.
Thanks to Stefan Sibiga for pointing this out.
Cc: Stefan Sibiga <stefansibiga@yahoo.ca>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix type of prog_cal and prog_tab variables to avoid any possible
calculation errors.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Misplaced parenthesis cause a calculation bug in
tda18271_rf_tracking_filters_init
Thanks to Stefan Sibiga for pointing this out.
Cc: Stefan Sibiga <stefansibiga@yahoo.ca>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get_user_pages() can return a negative error code when it fails. Set
buf->npages to 0 in that case, to prevent isp_video_buffer_cleanup()
from releasing invalid pages.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Subdevs already have their own entity, don't register as second one when
registering the subdev device node.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When open a device node, all entities part of the same pipeline are
powered on. If one of the entities fails to be powered on, the open
operations fails. In that case the device node entity use count must not
be incremented.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
To use the lane shifter, set different pixel formats at each end of
the link at the CCDC input.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for 8-bit bayer and 10- and 12-bit grey formats at the CCDC
input. Y12 is truncated to Y10 at the CCDC output.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We are currently using this flag to check whether it's safe
to call into ->request_fn(). If it is set, we punt to kblockd.
But we get a lot of false positives and excessive punts to
kblockd, which hurts performance.
The only real abuser of this infrastructure is SCSI. So export
the async queue run and convert SCSI over to use that. There's
room for improvement in that SCSI need not always use the async
call, but this fixes our performance issue and they can fix that
up in due time.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xen-kbdfront - fix mouse getting stuck after save/restore
Input: estimate number of events per packet
Input: evdev - indicate buffer overrun with SYN_DROPPED
Input: document event types and codes and their intended use
Input: add KEY_IMAGES specifically for AL Image Browser
Input: twl4030_keypad - fix potential NULL dereference in twl4030_kp_probe()
Input: h3600_ts - fix error handling at connect
Input: twl4030_keypad - avoid potential NULL-pointer dereference
Mouse gets "stuck" after restore of PV guest but buttons are in working
condition.
If driver has been configured for ABS coordinates at start it will get
XENKBD_TYPE_POS events and then suddenly after restore it'll start getting
XENKBD_TYPE_MOTION events, that will be dropped later and they won't get
into user-space.
Regression was introduced by hunk 5 and 6 of
5ea5254aa0ad269cfbd2875c973ef25ab5b5e9db
("Input: xen-kbdfront - advertise either absolute or relative
coordinates").
Driver on restore should ask xen for request-abs-pointer again if it is
available. So restore parts that did it before 5ea5254.
Acked-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
[v1: Expanded the commit description]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Calculate a default based on the number of ABS axes, REL axes,
and MT slots for the device during input device registration.
Signed-off-by: Jeff Brown <jeffbrown@android.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For some reason, sending QoS configuration causes transmission to stop
after a single frame on HT channels when not associated. Removing the
extra QoS configuration has no effect on station mode, and fixes
injection mode.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Instead of overloading __blk_run_queue to force an offload to kblockd
add a new blk_run_queue_async helper to do it explicitly. I've kept
the blk_queue_stopped check for now, but I suspect it's not needed
as the check we do when the workqueue items runs should be enough.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In omap_rtc_probe error path, free_irq() was using NULL rather than the
driver data as the data pointer so free_irq() wouldn't have matched.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: "George G. Davis" <gdavis@mvista.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux@googlegroups.com
Link: http://lkml.kernel.org/r/%3C1303005778.2889.2.camel%40phoenix%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We just need to make sure that an unplug event wakes up the md
thread, which is exactly what mddev_check_plugged does.
Also remove some plug-related code that is no longer needed.
Signed-off-by: NeilBrown <neilb@suse.de>
In raid5 plugging is used for 2 things:
1/ collecting writes that require a bitmap update
2/ collecting writes in the hope that we can create full
stripes - or at least more-full.
We now release these different sets of stripes when plug_cnt
is zero.
Also in make_request, we call mddev_check_plug to hopefully increase
plug_cnt, and wake up the thread at the end if plugging wasn't
achieved for some reason.
Signed-off-by: NeilBrown <neilb@suse.de>
When an md device adds a request to a queue, it can call
mddev_check_plugged.
If this succeeds then we know that the md thread will be woken up
shortly, and ->plug_cnt will be non-zero until then, so some
processing can be delayed.
If it fails, then no unplug callback is expected and the make_request
function needs to do whatever is required to make the request happen.
Signed-off-by: NeilBrown <neilb@suse.de>
md has some plugging infrastructure for RAID5 to use because the
normal plugging infrastructure required a 'request_queue', and when
called from dm, RAID5 doesn't have one of those available.
This relied on the ->unplug_fn callback which doesn't exist any more.
So remove all of that code, both in md and raid5. Subsequent patches
with restore the plugging functionality.
Signed-off-by: NeilBrown <neilb@suse.de>
Now that unplugging is done differently, the unplug_fn callback is
never called, so it can be completely discarded.
Signed-off-by: NeilBrown <neilb@suse.de>
md/raid submits a lot of IO from the various raid threads.
So adding start/finish plug calls to those so that some
plugging happens.
Signed-off-by: NeilBrown <neilb@suse.de>
Several tests in the ipv6 routing code check IFF_LOOPBACK, and
allowing stacking such as VLAN'ing on top of loopback results in a
netdevice which reports IFF_LOOPBACK but really isn't the loopback
device.
Instead of spamming the ipv6 routing code with even more special tests,
simply disallow VLAN over loopback.
The result of this patch is:
# modprobe 8021q
# vconfig add lo 43
ERROR: trying to add VLAN #43 to IF -:lo:- error: Operation not supported
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes port identification on optic devices when there's no link on the port.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a failure to stop a module in the pipeline is detected, the only
way to recover is to reset the ISP. However, as other users can be using
a different pipeline with other modules, the ISP can't be reset
synchronously with the error detection.
Mark the ISP as needing a reset when a failure to stop a pipeline is
detected, and reset the ISP when the last user releases the last
reference to the ISP.
Modify the omap3isp_pipeline_set_stream() function to record the new ISP
pipeline state only when no error occurs, except when stopping the
pipeline in which case the pipeline is still marked as stopped.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct ispstat_generic_config's comments refers to isph3a_aewb_config,
isph3a_af_config and isphist_config. But those structs have had their
names prefixed with 'omap3'. So, let's update the comments.
Signed-off-by: David Cohen <david.cohen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The link flags were not properly handled in __media_entity_setup_link
which could lead to link_notify callback to be called when the flags are
not modified. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It doesn't get more trivial than these.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Round properly the rsz factor so that we get highest rsz so that the input
width (or height) is highest possible smaller or equal to what the user
asks.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the number of phases/taps, used to select the correct equations to
compute the ratio, depends on the ratio, start with the 7-tap mode
equations to compute an approximation of the ratio, and switch to the
4-tap mode equations if the approximation is lower than or equal to 512.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Apparently some distros set i2c-algo-bit.bit_test to 1 by
default. In some cases this causes i2c_bit_add_bus
to fail and prevents the i2c bus from being added. In the
radeon case, we fail to add the ddc i2c buses which prevents
the driver from being able to detect attached monitors.
The i2c bus works fine even if bit_test fails. This is likely
due to gpio switching that is required and handled in the
pre/post_xfer hooks, so call the pre/post_xfer hooks in the
bit test as well.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=36221
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org [.38 down to .34]
When warning on the use of deprecated i2c_driver methods
attach_adapter and detach_adapter, mention the name of the driver
which needs to be updated.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (43 commits)
Revert "USB: isp1760-hcd: move imask clear after pending work is done"
xHCI: Implement AMD PLL quirk
xhci: Tell USB core both roothubs lost power.
usbcore: Bug fix: system can't suspend with USB3.0 device connected to USB3.0 hub
USB: Fix unplug of device with active streams
USB: xhci - also free streams when resetting devices
xhci: Fix NULL pointer deref in handle_port_status()
USB: xhci - fix math in xhci_get_endpoint_interval()
USB: xhci: simplify logic of skipping missed isoc TDs
USB: xhci - remove excessive 'inline' markings
USB: xhci: unsigned char never equals -1
USB: xhci - fix unsafe macro definitions
USB: fix formatting of SuperSpeed endpoints in /proc/bus/usb/devices
USB: isp1760-hcd: move imask clear after pending work is done
USB: fsl_qe_udc: send ZLP when zero flag and length % maxpacket == 0
usb: qcserial add missing errorpath kfrees
usb: qcserial avoid pointing to freed memory
usb: Fix qcserial memory leak on rmmod
USB: ftdi_sio: add ids for Hameg HO720 and HO730
USB: option: Added support for Samsung GT-B3730/GT-B3710 LTE USB modem.
...
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Set FLAGS_HAS_TIMEOUT during futex_wait restart setup
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_event: Fix cgrp event scheduling bug in perf_enable_on_exec()
perf: Fix a build error with some GCC versions
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix erroneous all_pinned logic
sched: Fix sched-domain avg_load calculation
* 'timer-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: rtc-mrst: follow on to the change of rtc_device_register()
RTC: add missing "return 0" in new alarm func for rtc-bfin.c
RTC: Fix s3c compile error due to missing s3c_rtc_setpie
RTC: Fix early irqs caused by calling rtc_set_alarm too early
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd: Disable GartTlbWlkErr when BIOS forgets it
x86, NUMA: Fix fakenuma boot failure
x86/mrst: Fix boot crash caused by incorrect pin to irq mapping
x86/ce4100: Add reg property to bridges
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6879/1: fix personality test wrt usage of domain handlers
ARM: 6878/1: fix personality flag propagation across an exec
ARM: 6877/1: the ADDR_NO_RANDOMIZE personality flag should be honored with mmap()
ARM: 6876/1: Kconfig.debug: Remove unused CONFIG_DEBUG_ERRORS
ARM: pxa: convert incorrect IRQ_TO_IRQ() to irq_to_gpio()
ARM: mmp: align NR_BUILTIN_GPIO with gpio interrupt number
ARM: pxa: align NR_BUILTIN_GPIO with GPIO interrupt number
ARM: pxa: always clear LPM bits for PXA168 MFPR
pcmcia: limit pxa2xx_trizeps4 subdriver to trizeps4 platform
pcmcia: limit pxa2xx_balloon3 subdriver to balloon3 platform
ARM: pxafb: Fix access to nonexistent member of pxafb_info
ARM: 6872/1: arch:common:Makefile Remove unused config in the Makefile.
ARM: 6868/1: Preserve the VFP state during fork
ARM: 6867/1: Introduce THREAD_NOTIFY_COPY for copy_thread() hooks
ARM: 6866/1: Do not restrict HIGHPTE to !OUTER_CACHE
ARM: 6865/1: perf: ensure pass through zero is counted on overflow
ARM: 6864/1: hw_breakpoint: clear DBGVCR out of reset
ARM: Only allow PM_SLEEP with CPUs which support suspend
ARM: Make consolidated PM sleep code depend on PM_SLEEP
This patch fixes two issues:
- A disabled crtc does not use any lb, so return 0 for
lb size. This makes the display priority calculation
more exact.
- Only use 1/2 and whole lb partitions. Using smaller
partitions can cause underflow to one of the displays
if you have multiple large displays on the same lb.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=34534
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix a possible problem with mport registration left non-cleared after
fsl_rio_setup() exits on link error. Abort mport initialization if
registration failed.
This patch is applicable to 2.6.39-rc1 only. The problem does not exist
for earlier versions.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the wrong members and the wrong function's definition, since the
irq_chip had changed.
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the driver aware of the initial status of the regulator.
The leds-regulator driver was ignoring the initial status of the
regulator; this resulted in rdev->use_count being incremented to 2 after
calling regulator_led_set_value() in the .probe method when a regulator
was already enabled at insmod time, which made it impossible to ever
disable the regulator.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The platform_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes the i2c test in i2c_bit_add_bus fails
if this happens we fail to register the i2c adapter and
eventually fail to add the connector. If i2c fails,
add the connector to the user can at least force
it on.
Note that some distros set i2c-algo-bit.bit_test to 1 by
default which sometimes fails preventing the ddc i2c adapter
from being added. The i2c adapter works even if the bit test
fails, probably due to pre/post_xfer not getting called in
the test_bit function. I have another patch to follow
up on that.
See:
https://bugs.freedesktop.org/show_bug.cgi?id=36221
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The memory leak was caused by unintentional assignment of the Rx path
destroy callback function pointer to NULL just after correct
initialization.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a kernel crash, bna control path state machine and firmware do not
get a notification and hence are not cleanly shutdown. The registers
holding driver/IOC state information are not reset back to valid
disabled/parking values. This causes subsequent driver initialization
to hang during kdump kernel boot. This patch, during the initialization
of first PCI function, resets corresponding register when unclean shutown
is detect by reading chip registers. This will make sure that ioc/fw
gets clean re-initialization.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 5808544690.
To quote Richard:
I don't think this should be mainlined. It was a
misunderstanding on my part. If you see all the other hdc
drivers in the same location, they all do the same thing (i.e.
clear the interrupt status first, then do the work) that
"glitch" I think I saw was actually two back-to-back
interrupts.
Sebastian (the original author of isp1760) explained it to me a
few days after my submission.
sorry for the confusion
Cc: Richard Retanubun <RichardRetanubun@ruggedcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch disable the optional PM feature inside the Hudson3 platform under
the following conditions:
1. If an isochronous device is connected to xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
The PM feature needs to be disabled to eliminate PLL startup delays when the
link comes out of low power state. The performance of DMA data transfer could
be impacted if system delay were encountered and in addition to the PLL start
up delays. Disabling the PM would leave room for unpredictable system delays
in order to guarantee uninterrupted data transfer to isochronous audio or
video stream devices that require time sensitive information. If data in an
audio/video stream was interrupted then erratic audio or video performance
may be encountered.
AMD PLL quirk is already implemented in OHCI/EHCI driver. After moving the
quirk code to pci-quirks.c and export them, xHCI driver can call it directly
without having the quirk implementation in itself.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
On a resume, when the power is lost during hibernate, the USB core will
call hub_reset_resume for the xHCI USB 2.0 roothub, but not for the USB
3.0 roothub:
[ 164.748310] usb usb1: root hub lost power or was reset
[ 164.748353] usb usb2: root hub lost power or was reset
[ 164.748487] usb usb3: root hub lost power or was reset
[ 164.748488] xhci_hcd 0000:01:00.0: Stop HCD
...
[ 164.870039] hub 4-0:1.0: hub_resume
...
[ 164.870054] hub 3-0:1.0: hub_reset_resume
This causes issues later, because the USB core assumes the USB 3.0 hub
attached to the USB 3.0 roothub is still active. It attempts to queue a
control URB for the external hub, which fails because all the device
slot contexts were released when the USB 3.0 roothub lost power:
[ 164.980044] hub 4-1:1.0: hub_resume
[ 164.980047] xhci_hcd 0000:01:00.0: Get port status returned 0x10101
[ 164.980049] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980053] hub 3-0:1.0: port 1: status 0101 change 0001
[ 164.980056] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980060] xhci_hcd 0000:01:00.0: `MEM_WRITE_DWORD(3'b000, 32'hffffc90008948440, 32'h202e1, 4'hf);
[ 164.980062] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980066] xhci_hcd 0000:01:00.0: clear port connect change, actual port 0 status = 0x2e1
[ 164.980069] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980072] xhci_hcd 0000:01:00.0: get port status, actual port 1 status = 0x2a0
[ 164.980074] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980077] xhci_hcd 0000:01:00.0: Get port status returned 0x100
[ 164.980079] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980082] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980085] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980088] hub 4-1:1.0: port 4: status 0000 change 0000
[ 164.980091] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980094] hub 4-1:1.0: activate --> -22
[ 164.980113] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980117] hub 4-1:1.0: hub_port_status failed (err = -22)
[ 164.980119] xHCI xhci_urb_enqueue called with unaddressed device
[ 164.980123] hub 4-1:1.0: can't resume port 4, status -22
[ 164.980126] hub 4-1:1.0: port 4 status ffff.ffff after resume, -22
[ 164.980129] usb 4-1.4: can't resume, status -22
[ 164.980131] hub 4-1:1.0: logical disconnect on port 4
This causes issues when a USB 3.0 hard drive is attached to the external
USB 3.0 hub when the system is hibernated:
[ 6249.849653] sd 8:0:0:0: [sdb] Unhandled error code
[ 6249.849659] sd 8:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 6249.849663] sd 8:0:0:0: [sdb] CDB: Read(10): 28 00 00 00 2a 08 00 00 02 00
[ 6249.849671] end_request: I/O error, dev sdb, sector 10760
Make sure to inform the USB core that *both* xHCI roothubs lost power.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch clear PORT_POWER when suspend a USB3.0 device behind a USB3.0
external hub, so the system can suspend and resume.
Note USB3.0 device may not work after system resume and this is a temporary
workaround. The correct fix will be in future patches.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If I unplug a device while the UAS driver is loaded, I get an oops
in usb_free_streams(). This is because usb_unbind_interface() calls
usb_disable_interface() which calls usb_disable_endpoint() which sets
ep_out and ep_in to NULL. Then the UAS driver calls usb_pipe_endpoint()
which returns a NULL pointer and passes an array of NULL pointers to
usb_free_streams().
I think the correct fix for this is to check for the NULL pointer
in usb_free_streams() rather than making the driver check for this
situation. My original patch for this checked for dev->state ==
USB_STATE_NOTATTACHED, but the call to usb_disable_interface() is
conditional, so not all drivers would want this check.
Note from Sarah Sharp: This patch does avoid a potential dereference,
but the real fix (which will be implemented later) is to set the
.soft_unbind flag in the usb_driver structure for the UAS driver, and
all drivers that allocate streams. The driver should free any streams
when it is unbound from the interface. This avoids leaking stream rings
in the xHCI driver when usb_disable_interface() is called.
This should be queued for stable trees back to 2.6.35.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Currently, when resetting a device, xHCI driver disables all but one
endpoints and frees their rings, but leaves alone any streams that
might have been allocated. Later, when users try to free allocated
streams, we oops in xhci_setup_no_streams_ep_input_ctx() because
ep->ring is NULL.
Let's free not only rings but also stream data as well, so that
calling free_streams() on a device that was reset will be safe.
This should be queued for stable trees back to 2.6.35.
Reviewed-by: Micah Elizabeth Scott <micah@vmware.com>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
When we get a port status change event, we need to figure out what type of
port it came from: a USB 3.0 port, or a USB 2.0/1.1 port. We can't know
which usb_hcd to use until that point, so hcd will be NULL for part of the
function. Unfortunately, if any of the sanity checks fail, we'll jump to
the cleanup label before hcd is set to a valid pointer, and then we'll
attempt to tell the USB core to kick the hcd, which is NULL.
Skip kicking the roothub if the sanity checks fail.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When parsing exponent-expressed intervals we subtract 1 from the
value and then expect it to match with original + 1, which is
highly unlikely, and we end with frequent spew:
usb 3-4: ep 0x83 - rounding interval to 512 microframes
Also, parsing interval for fullspeed isochronous endpoints was
incorrect - according to USB spec they use exponent-based
intervals (but xHCI spec claims frame-based intervals). I trust
USB spec more, especially since USB core agrees with it.
This should be queued for stable kernels back to 2.6.31.
Reviewed-by: Micah Elizabeth Scott <micah@vmware.com>
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
The logic of the handling Missed Service Error Events was pretty
confusing as we were checking the same condition several times.
In addition, it caused compiler warning since the compiler could
not figure out that event_trb is actually unused in case we are
skipping current TD.
Fix that by rearranging "skip" condition checks, and factor out
skip_isoc_td() so that it is called explicitly.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Remove 'inline' markings from file-local functions and let compiler
do its job and inline what makes sense for given architecture.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
There were some places that compared port_speed == -1 where port_speed
is a u8. This doesn't work unless we cast the -1 to u8. Some places
did it correctly.
Instead of using -1 directly, I've created a DUPLICATE_ENTRY define
which does the cast and is more descriptive as well.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Macro arguments used in expressions need to be enclosed in parenthesis
to avoid unpleasant surprises.
This should be queued for kernels back to 2.6.31
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Isochronous and interrupt SuperSpeed endpoints use the same mechanisms
for decoding bInterval values as HighSpeed ones so adjust the code
accordingly.
Also bandwidth reservation for SuperSpeed matches highspeed, not
low/full speed.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the HcInterrupt register write to clear the
pending interrupt to after the isr work is done, doing this removes
glitches in the irq line.
Signed-off-by: Richard Retanubun <richardretanubun@ruggedcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver did not take the zero flag in the USB request. If the
request length is the same as the endpoint's maxpacket, an additional
ZLP with no data has to be transmitted.
The method used here is inspired to what is done in fsl_udc_core.c
(and pxa27x_udc.c and at91_udc.c) where this is supported.
There already was a discussion about this topic with people from
Keymile, and I propose here a better implementation:
http://thread.gmane.org/gmane.linux.usb.general/38951
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are two -ENODEV error paths in qcprobe where the allocated private
data is not freed, this patch adds the two missing kfrees to avoid
leaking memory on the error path
Signed-off-by: Steven Hardy <shardy@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the qcprobe logic such that serial->private is not set when
qcprobe exits with -ENODEV, otherwise serial->private will point to freed
memory on -ENODEV
Signed-off-by: Steven Hardy <shardy@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qcprobe function allocates serial->private but this is never freed, this
patch adds a new function qc_release() which frees serial->private, after
calling usb_wwan_release
Signed-off-by: Steven Hardy <shardy@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb serial: ftdi_sio: add two missing USB ID's for Hameg interfaces HO720
and HO730
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bind only modem AT command endpoint to option.
Signed-off-by: Marius B. Kotsbak <marius@kotsbak.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There was an unlock missing on the error path.
Also I did a small cleanup by changing ep->dev->lock for just dev->lock.
They're the same lock, but dev->lock is shorter and that's how it is
used for the spin_unlock_irqrestore() call.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Booting latest kernel on my test machine produces a lockdep
warning from the usb_amd_find_chipset_info() function:
WARNING: at /data/lemmy/linux.trees.git/kernel/lockdep.c:2465 lockdep_trace_alloc+0x95/0xc2()
Hardware name: Snook
Modules linked in:
Pid: 959, comm: work_for_cpu Not tainted 2.6.39-rc2+ #22
Call Trace:
[<ffffffff8103c0d4>] warn_slowpath_common+0x80/0x98
[<ffffffff812387e6>] ? T.492+0x24/0x26
[<ffffffff8103c101>] warn_slowpath_null+0x15/0x17
[<ffffffff81068667>] lockdep_trace_alloc+0x95/0xc2
[<ffffffff810ed9ac>] slab_pre_alloc_hook+0x18/0x3b
[<ffffffff810ef227>] kmem_cache_alloc_trace+0x25/0xba
[<ffffffff812387e6>] T.492+0x24/0x26
[<ffffffff81238816>] pci_get_subsys+0x2e/0x73
[<ffffffff8123886c>] pci_get_device+0x11/0x13
[<ffffffff814082a9>] usb_amd_find_chipset_info+0x3f/0x18a
...
It turns out that this function calls pci_get_device under a spin_lock
with irqs disabled, but the pci_get_device function is only allowed in
preemptible context.
This patch fixes the warning by making all data-structure
modifications on temporal storage and commiting this back
into the visible structure at the end. While at it, this
patch also moves the pci_dev_put calls out of the spinlocks
because this function might sleep too.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In file included from drivers/usb/host/ohci-hcd.c:1028:0:
drivers/usb/host/ohci-au1xxx.c:36:7: warning: "__BIG_ENDIAN" is not defined
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add PID 0x0103 for serial port of the OCT DK201 docking station.
Reported-by: Jan Hoogenraad <jan@hoogenraad.net>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build failure introduced by commit
7acc6197b7 (usb: musb: Idle path retention
and offmode support for OMAP3) when building without gadget
support.
CC drivers/usb/musb/omap2430.o
drivers/usb/musb/omap2430.c: In function ‘musb_otg_notifications’:
drivers/usb/musb/omap2430.c:262: error: ‘struct musb’ has no member named ‘gadget_driver’
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1458) fixes a problem affecting ultra-reliable systems:
When hardware failover of an EHCI controller occurs, the data
structures do not get released correctly. This is because the routine
responsible for removing unused QHs from the async schedule assumes
the controller is running properly (the frame counter is used in
determining how long the QH has been idle) -- but when a failover
causes the controller to be electronically disconnected from the PCI
bus, obviously it stops running.
The solution is simple: Allow scan_async() to remove a QH from the
async schedule if it has been idle for long enough _or_ if the
controller is stopped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-Tested-by: Dan Duval <dan.duval@stratus.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During processing of bunch of eem frames if "echo" command is found
skb is cloned and the cloned version should be used to send reply.
Unfortunately, the data of the original skb were actually used and
the cloned skb is never freed.
Using the cloned skb and freeing the skb in the completion callback
for usb request.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I added new ProdutIds for two devices from CTI GmbH Leipzig.
Signed-off-by: Christian Simon <simon@swine.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because the disconnect function in the composite driver will call spin_lock,
this driver has to call spin_unlock before calling driver->disconnet().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable USB_ARCH_HAS_EHCI in arch Kconfig and enable it in usb Kconfig
Warning log:
warning: (MICROBLAZE) selects USB_ARCH_HAS_EHCI which has unmet
direct dependencies (USB_SUPPORT)
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ep_read() acquires data->lock mutex in get_ready_ep() and releases it on
all paths except for one: when usb_endpoint_xfer_isoc() failed. The
patch adds mutex_unlock(&data->lock) at that path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix printk format build warning and grammar typo on same line.
drivers/usb/host/isp1760-hcd.c:300: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-greg' of git://gitorious.org/usb/usb:
USB: musb: blackfin: work around anomaly 05000450
usb: musb: Fix the crash issue during reboot
usb: musb: gadget: check the correct list_head
usb: musb: temporarily make it bool
USB: musb: dereferencing an iomem pointer
USB: musb: silence printk format warning
USB: musb: using 0 instead of NULL
USB: musb: add missing unlock in cppi_interrupt()
usb: musb: ux500: copy dma mask from platform device to musb device
usb: musb: clear AUTOSET while clearing DMAENAB
priv->tx_power_next is not initialized to max supported power,
but instead default value is used, what cause errors like
[ 58.597834] iwl3945 0000:03:00.0: Requested user TXPOWER 15 above upper limit 14.
[ 58.597839] iwl3945 0000:03:00.0: Error setting Tx power (-22).
if maximum tx power read from the eeprom is smaller than default.
In consequence card is unable to initialize properly. Fix the problem
and cleanup tx power initialization.
Reported-and-tested-by: Robin Dong <hao.bigrat@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 74888760d4
"dt/net: Eliminate users of of_platform_{,un}register_driver"
broke building mscan driver. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using uninitialised watermarks values for disabled pipes which
were combined into a single WM register and so corrupting the values for
the enabled pipe and upsetting the display hardware.
Reported-by: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32612
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (22 commits)
Revert "i915: restore only the mode of this driver on lastclose"
Revert "ttm: Utilize the DMA API for pages that have TTM_PAGE_FLAG_DMA32 set."
i915: select VIDEO_OUTPUT_CONTROL for ACPI_VIDEO
drm/radeon/kms: properly program vddci on evergreen+
drm/radeon/kms: add voltage type to atom set voltage function
drm/radeon/kms: fix pcie_p callbacks on btc and cayman
drm/radeon/kms: fix suspend on rv530 asics
drm/radeon/kms: clean up gart dummy page handling
drm/radeon/kms: make radeon i2c put/get bytes less noisy
drm/radeon/kms: pll tweaks for rv6xx
drm/radeon: Fix KMS legacy backlight support if CONFIG_BACKLIGHT_CLASS_DEVICE=m.
radeon: Fix KMS CP writeback on big endian machines.
i915: restore only the mode of this driver on lastclose
drm/nvc0: improve vm flush function
drm/nv50-nvc0: remove some code that doesn't belong here
drm/nv50: use "nv86" tlb flush method on everything except 0x50/0xac
drm/nouveau: quirk for XFX GT-240X-YA
drm/nv50-nvc0: work around an evo channel hang that some people see
drm/nouveau: implement init table opcode 0x5c
drm/nouveau: fix oops on unload with disabled LVDS panel
...
When the crop rectangle needs to be modified to match hardware
requirements, center the resulting rectangle on the requested rectangle
instead of removing pixels from the right and bottom sides only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since commit
379fa5d ([media] V4L: mx3_camera: convert to videobuf2)
mx3_camera uses videobuf2, but that commit didn't upgrade the select
resulting in the following build failure:
drivers/built-in.o: In function `mx3_camera_init_videobuf':
clkdev.c:(.text+0x86580): undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `mx3_camera_probe':
clkdev.c:(.devinit.text+0x3548): undefined reference to `vb2_dma_contig_init_ctx'
clkdev.c:(.devinit.text+0x3578): undefined reference to `vb2_dma_contig_cleanup_ctx'
drivers/built-in.o: In function `mx3_camera_remove':
clkdev.c:(.devexit.text+0x674): undefined reference to `vb2_dma_contig_cleanup_ctx'
make[2]: *** [.tmp_vmlinux1] Error 1
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the camera host driver (sh_mobile_ceu_camera.c) is unloaded and then
reloaded, probe will fail, because camera client .set_bus_param() and
.query_bus_param() methods have been set to NULL. Fix this by caching
the original pointers and restoring them on driver-unbind.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
i2c_unregister_device() frees the I2C client, so, dereferencing it
afterwards is a bug, that leads to Oopses.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the introduction of CSI2 support on sh-mobile, the host driver
switched to using v4l2_device_call_until_err() with grp_id == 0 to
call subdev operations on the sensor and the CSI2 subdev. However,
this has broken multi-client set ups like the one on migor, because
that way all operations get called on both clients. To fix this add
a grp_id and set it to the client private context.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
buf->size is not yet initialised in videobuf2-dma-contig at the time of
the error message, use "size."
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videobuf2-dma-contig allocator returns an ERR_PTR() on failure, not
a NULL like all other allocators. Fix videobuf2-core to also correctly
recognise those failures.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If allocating stream buffers for one of the primary streams (e.g. YUV)
failed during card probe, the error path clean up would try to manipulate
the yet unitialized IDX stream structures. This caused a BUG due to
unitialized list heads.
Detect that case and ignore the uninitialized IDX stream.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DMA mode 1 data corruption anomaly on Blackfin systems. This issue is
specific to the Blackfin silicon as the bug appears to be related to the
connection of the musb ip to the bus/dma fabric.
Data corruption when using USB DMA mode 1. (Issue manager 17-01-0105)
DMA mode 1 allows large size transfers to generate a single interrupt
at the end of the entire transfer. The transfer is split up in packets
of length specified in the Maximum Packet Size field for that endpoint.
If the transfer size is not an integer multiple of the Maximum Packet
Size, a short packet will be present at the end of the transfer.
Under certain conditions this packet may be corrupted in the USB FIFO.
Workaround:
Use DMA mode 1 to transfer (n* Maximum Packet Size) and schedule DMA
mode 0 to transfer the short packet.
As an example if your transfer size is 33168 bytes and Maximum Packet
Size equals 512, schedule [33168 - (33168 mod 512)] in DMA mode 1 and
the remainder (33168 mod 512) in DMA mode 0.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We are now using our own list_head, so we should
be checking against that, not the gadget driver's
list_head.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to the recent changes to musb's glue layers,
we can't compile musb-hdrc as a module - compilation
will break due to undefined symbol musb_debug. In
order to fix that, we need a big re-work of the
debug support on the MUSB driver.
Because that would mean a lot of new code coming
into the -rc series, it's best to defer that to
next merge window and for now just disable module
support for MUSB.
Once we get the refactor of the debugging support
done, we can simply revert this patch and things
will go back to normal again.
Cc: stable@kernel.org # v2.6.38
Signed-off-by: Felipe Balbi <balbi@ti.com>
"tx_ram" points to io memory. We can't dereference it directly. Sparse
complains about this: "drivers/usb/musb/cppi_dma.c:1205:25: warning:
dereference of noderef expression"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gcc gives the following warnings:
drivers/usb/musb/cppi_dma.c: In function ‘cppi_next_tx_segment’:
drivers/usb/musb/cppi_dma.c:600: warning: format ‘%x’ expects type ‘unsigned int’, but argument 8 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c: In function ‘cppi_next_rx_segment’:
drivers/usb/musb/cppi_dma.c:822: warning: format ‘%x’ expects type ‘unsigned int’, but argument 9 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c: In function ‘cppi_rx_scan’:
drivers/usb/musb/cppi_dma.c:1042: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 4 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c:1114: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 7 has type ‘dma_addr_t’
dma_addr_t is sometimes 32 bit and sometimes 64. We normally cast them
to unsigned long long for printk().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On the completion of tx dma, dma is disabled by clearing MUSB_TXCSR_DMAENAB in
TXCSR. If MUSB_TXCSR_AUTOSET was set in txstate() it will remain set although
it is not needed in PIO mode. Clear it as soon as it is not needed.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a new EV_SYN code, SYN_DROPPED, to inform the client when input
events have been dropped from the evdev input buffer due to a
buffer overrun. The client should use this event as a hint to
reset its state or ignore all following events until the next
packet begins.
Signed-off-by: Jeff Brown <jeffbrown@android.com>
[dtor@mail.ru: Implement Henrik's suggestion and drop old events in
case of overflow.]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This fixes the failure to register the IRQ_RTCAlrm alarm as a wakeup
event. It is misinterpreted as a gpio irq not a PWER bitmask. Fixed
this by converting the incorrect IRQ_TO_IRQ() to a correct version of
irq_to_gpio().
Reported-by: Nick Bane <nickbane1@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This reverts commit 0a0883c843.
this was in my tree by accident, I meant to rebase it out and
didn't realise in time.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 69a07f0b11.
We've tracked a number of problems back to this, and Thomas
thinks we should redesign this for .40/41 anyways so I'm
happy to revert it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
fix Kconfig warning:
(DRM_I915 && STUB_POULSBO) selects ACPI_VIDEO which has unmet direct dependencies
(ACPI && X86 && BACKLIGHT_CLASS_DEVICE && VIDEO_OUTPUT_CONTROL && INPUT)
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Change vddci as well as vddc when changing power modes
on evergreen/ni. Also, properly set vddci on boot up
for ni cards. The vbios only sets the limited clocks
and voltages on boot until the mc ucode is loaded. This
should fix stability problems on some btc cards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is needed for setting voltages other than vddc.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
btc and cayman asics use the same callback for
pcie port registers.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Apparently only rv515 asics need the workaround
added in f24d86f1a4
(drm/radeon/kms: fix resume regression for some r5xx laptops).
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=34709
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
As per Konrad's original patch, the dummy page used
by the gart code and allocated in radeon_gart_init()
was not freed properly in radeon_gart_fini().
At the same time r6xx and newer allocated and freed the
dummy page on their own. So to do Konrad's patch one
better, just remove the allocation and freeing of the
dummy page in the r6xx, 7xx, evergreen, and ni code and
allocate and free in the gart_init/fini() functions for
all asics.
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Enabling write-combining may also enable read reordering. The BIU is
only guaranteed to read from a 128-bit CSR or 64-bit SRAM word when
the host reads from its lowest address; otherwise the BIU may use the
latched value. Therefore we need to reinstate the read memory
barriers after the first read operation for each CSR or SRAM word.
Signed-off-by; Ben Hutchings <bhutchings@solarflare.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
thinkpad-acpi fails to load with newer Thinkpad X201s BIOS
acer-wmi: Fix capitalisation of GUID in module alias
sony-laptop: keyboard backlight fixes
sony-laptop: only show the handles sysfs file in debug mode
samsung-laptop: set backlight type
staging: samsung-laptop has moved to platform/x86
samsung-laptop: Samsung R410P backlight driver
samsung-laptop: add support for N230 model
platform-drivers: x86: pmic: Restore the dropped buslock/unlock
sony-laptop: fix early NULL pointer dereference
msi-laptop: fix config-dependent build error
eeepc-wmi: add keys found on EeePC 1215T
asus-wmi: swap input name and phys
asus-laptop: remove removed features from feature-removal-schedule.txt
When a skb is delivered to a registered callback, cn_call_callback()
incorrectly returns -ENODEV after freeing the skb, causing cn_rx_skb()
to free the skb a second time.
Reported-by: Eric B Munson <emunson@mgebm.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the correct module name and device interface so that
ethtool can display the proper values.
The firmware version will be fixed later on when the FW
can actually report a version. :)
Reported-by: Richard Farina <sidhayn@gmail.com>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Tested-by: Richard Farina <sidhayn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During PHY errors, the MAC can sometimes fail to enter an idle state on older
hardware (before AR9380) after an rx stop has been requested.
This typically shows up in the kernel log with messages like these:
ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]()
Call Trace:
[<8023f0e8>] dump_stack+0x8/0x34
[<80075050>] warn_slowpath_common+0x78/0xa4
[<80075094>] warn_slowpath_null+0x18/0x24
[<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k]
[<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k]
[<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k]
When this happens, the state that the MAC enters is easy to identify and
does not result in bogus DMA traffic, however to ensure a working state
after a channel change, the hardware should still be reset.
This patch adds detection for this specific MAC state, after which the above
warnings completely disappear in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to booting, we need to inspect the state left by the BIOS and
remove any conflicting bits before we take over. The example reported by
Seth Forshee is very similar to the bug we encountered with the state left
by grub2, that the crtc pipe<->planning mapping was reversed from our
expectations and so we failed to turn off the outputs when booting or,
in this case, resuming. This may be in fact the same bug, but triggered
at resume time.
This patch rearranges the code we already have to clear up the
conflicting state upon init and calls it from reset (which is called
after we have lost control of the hardware, i.e. along both the boot and
resume paths) instead.
Reported-and-tested-by: Seth Forshee <seth.forshee@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35796
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
The tidy ups in 7f58aabc36 ("drm/i915:
cleanup per-pipe reg usage") changed intel_crtc->plane to intel_crtc->pipe in
intel_tv_mode_set(). This caused the screen to quickly turn off before
returning whenever modesetting/mode probing took place on my 915GM EeePC
900 creating a flickering effect. This patch changes intel_crtc->pipe back
to intel_crtc->plane which solves the problem for me.
References: https://bugs.freedesktop.org/show_bug.cgi?id=35903
Signed-off-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Humbly-acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
As a probe for a TV connection modifies the TV_CTL register, it causes a
loss of sync and a regular glitch on the output. This is highly
undesirable when using the TV, so only poll for TV connections and wait
for an explicit query for detecting the disconnection event.
Reported-by: Mathew McKernan <matmckernan@rauland.com.au>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35977
Signed-off-by: Mathew McKernan <matmckernan@rauland.com.au>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
During detect() we would probe the connection bits to determine if
there was a TV attached, and what video input type (Component, S-Video,
Composite, etc) to use. However, we promptly discarded this vital bit of
information and never propagated it to where it was used to determine
the correct modes and setup the control registers. Fix it!
This fixes a regression from 7b334fcb45.
Reported-and-tested-by: Mathew McKernan <matmckernan@rauland.com.au>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35977
Signed-off-by: Mathew McKernan <matmckernan@rauland.com.au>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Create a kconfig option symbol for PCI_LABEL and enable it
when DMI || ACPI are enabled.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During self-tests we use efx_process_channel_now() to handle
completion and other events synchronously. This disables interrupts
and NAPI processing for the channel in question, but it may still be
interrupted by another channel. A single socket may receive packets
from multiple net devices or even multiple channels of the same net
device, so this can result in deadlock on a socket lock.
Receiving packets in process context will also result in incorrect
classification by the network cgroup classifier.
Therefore, we must only use efx_process_channel_now() in the offline
loopback tests (which never deliver packets up the stack) and not for
the online interrupt and event tests.
For the interrupt test, there is no reason to process events. We
only care that an interrupt is raised.
For the event test, we want to know whether events have been received,
and there may be many events ahead of the one we inject. Therefore
remove efx_channel::magic_count and instead test whether
efx_channel::eventq_read_ptr advances. This is currently an event
queue index and might wrap around to exactly the same value, resulting
in a false negative. Therefore move the masking to efx_event() and
efx_nic_eventq_read_ack() so that it cannot wrap within the time of
the test.
The event test also tries to diagnose failures by checking whether an
event was delivered without causing an interrupt. Add and use a
helper function that only does this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The new BIOS has a slightly different EC version string.
From a1541710300b083a1a9acff2890d721d15ede62b Mon Sep 17 00:00:00 2001
From: Keith Packard <keithp@keithp.com>
Date: Sun, 13 Mar 2011 23:46:22 -0700
Subject: [PATCH] thinkpad-acpi: Some BIOS versions don't end in WW, remove check
My X201s BIOS version string is 6QET46V1 (1.16 ). The
EC version string is 6QHT28WW-1.09. The driver was requiring that both
of these have 'WW' in positions 6 and 7. I don't know what the
significance of having 'V1' there instead is, but removing the test
makes the driver load on my machine.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
wmi:6AF4F258-B401-42Fd-BE91-3D4AC2D7C0D3 needs to be
wmi:6AF4F258-B401-42FD-BE91-3D4AC2D7C0D3 in module alias for acer-wmi is
automatically loaded.
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Lee, Chun-Yi <jlee@novell.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Restore the original state on module removal, set the latest values on
resume.
When setting the keyboard backlight mode try to turn on/off backlight
immediately.
[malattia@linux.it: patch taken from a largely modified sony-laptop.c,
ported and slightly modified to use defines already available.]
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
It makes no sense to expose this type of information to userspace unless
the driver was explicitly loaded with the debug option.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cherry-picked from drivers/staging/samsung-laptop/samsung-laptop.c
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
If the TX queues are running during loopback self tests, host
traffic gets looped back which causes the test to fail. Avoid
restarting the TX queues after the port reset so that any packets
sent by the host get held back until after the tests have completed.
[bwh: Also wake all TX queues at the end of self-tests.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Here's a trivial patch which adds support to the backlight device found
in Samsung R410 Plus laptops.
Signed-off-by: Alberto Mardegan <mardy@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[mmarek: cherry-picked from staging commit d542f180]
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[mmarek: cherry-picked from staging commit 0789b003]
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In case CONFIG_FB_PXA_OVERLAY is not defined, the pxafb_freq_transition()
function tests nonexistent member of pxafb_info (since the member is not
part of the structure).
Fix this by wraping the test in ifdef, even if I don't really like how the code
looks now. The check doesn't have to happen if overlays are disabled at all as
the check is always true then.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
In order for MFD drivers to fetch their cell pointer but also their
platform data one, an mfd cell pointer is added to the platform_device
structure.
That allows all MFD sub devices drivers to be MFD agnostic, unless
they really need to access their MFD cell data. Most of them don't,
especially the ones for IPs used by both MFD and non MFD SoCs.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We should first check whether platform data is NULL or not, before
dereferencing it to get the keymap.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'stable/bug-fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: Allow PV-OPS kernel to detect whether XSAVE is supported
xen: just completely disable XSAVE
xen/debug: Don't be so verbose with WARN on 1-1 mapping errors.
xen: events: fix error checks in bind_*_to_irqhandler()
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
dt/fsldma: fix build warning caused by of_platform_device changes
spi: Fix race condition in stop_queue()
gpio/pch_gpio: Fix output value of pch_gpio_direction_output()
gpio/ml_ioh_gpio: Fix output value of ioh_gpio_direction_output()
gpio/pca953x: fix error handling path in probe() call
Xen save/restore is going to use hibernate device callbacks for
quiescing devices and putting them back to normal operations and it
would need to select CONFIG_HIBERNATION for this purpose. However,
that also would cause the hibernate interfaces for user space to be
enabled, which might confuse user space, because the Xen kernels
don't support hibernation. Moreover, it would be wasteful, as it
would make the Xen kernels include a substantial amount of code that
they would never use.
To address this issue introduce new power management Kconfig option
CONFIG_HIBERNATE_CALLBACKS, such that it will only select the code
that is necessary for the hibernate device callbacks to work and make
CONFIG_HIBERNATION select it. Then, Xen save/restore will be able to
select CONFIG_HIBERNATE_CALLBACKS without dragging the entire
hibernate code along with it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Shriram Rajagopalan <rshriram@cs.ubc.ca>
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace relpy with reply.
replace premanent with permanent.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace tranmitted with transmitted.
replace tranmitting with transmitting.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Shah