This is due to the slave_configuration routine is getting called when
host reset is active, and config page reads are failing, and driver
attempts to added device with stale config data.
To fix the issue, added error checking in slave_configure to check
for configuration pages failing, and return "1" so the device is
not configured. The config pages are failing if raid volume is
configured while issuing a host reset, thus driver is reading stale
data and proceeding to attempt to add. The fix is to return error
so the volume is not configured.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is due to driver reporting a device missing to the OS then the OS sending
a SYNC_CACHE request to driver while the IO queues are locked due to host reset.
To fix the issue, the driver will be waking up the port enable context
immediately when the driver receives the reply message, instead of waiting
on the hot plug worker threads.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix for dead lock occurring between host_lock and sas_device_lock.
The deadlock is between two spin locks, between the shost->host_lock
and driver ioc->sas_device_lock.
The fix is to rearrange the code in the FW/Driver device removal
handshake so the ioc->sas_device_lock is not occurring when the
shost->host_lock is taken.
[jejb: zero initialise sas_address to fix spurious compiler warning]
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The fix is in the driver-firmware handshake device removal code. We
need to read the controller ioc_state to see if controller is OPERATIONAL
prior to sending target reset and OP_REMOVE. Previously it was checking
the flag ioc->shost_recovery flag, which is always set when host reset is
active, thus preventing drives from getting properly deleted.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The fix is to inhibit the warning message in _scsih_get_sas_address
when the MPI2_IOCSTATUS_CONFIG_INVALID_PAGE ioc status is returned.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix for issue : While discovery is in progress, hot unplug and hot plug of
enclosure connected to the controller card is causing system to hang.
When a device is in the process of being detected at driver load time then
if it is removed, the device that is no longer present will not be added
to the list. So the code in _scsih_probe_sas() is rearranged as such so
the devices that failed to be detected are not added to the list.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
New feature Fast Load Support.
(1)Asynchronous SCSI scanning: This will allow the drivers to scan
for devices in parallel while other device drivers are loading at
the same time. This will improve the amount of time it takes for the
OS to load.
(2) Reporting Devices while port enable is active: This feature will
allow devices to be reported to OS immediately while port enable is
active. The previous implementation waits for port enable to complete,
and then report devices. This feature is only enabled on IT firmware
configurations when there are no boot device configured in BIOS Configuration
Utility, else the driver will wait till port enable completes reporting
devices. For IR firmware, this feature is turned off. This feature is to
address large SAS topologies (>100 drives) when the boot OS is using onboard
SATA device, in other words, the boot devices is not
connected to our controller.
(3) Scanning for devices after diagnostic reset completes: A new routine
_scsih_scan_start is added. This will scan the expander pages, IR pages,
and sas device pages, then reporting new devices to SCSI Mid layer. It
seems the driver is not supporting adding devices while diagnostic reset
is active. Apparently this is due to the sanity checks on
ioc->shost_recovery flag throughout the context of kernel work thread FIFO,
and the mpt2sas_fw_work.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Support added for controllers capable of multi reply queues.
The following are the modifications to the driver to support NUMA.
1) Create the new structure adapter_reply_queue to contain the reply queue
info for every msix vector. This object will contain a
reply_post_host_index, reply_post_free for each instance, msix_index, among
other parameters. We will track all the reply queues on a link list called
ioc->reply_queue_list. Each reply queue is aligned with each IRQ, and is
passed to the interrupt via the bus_id parameter.
(2) The driver will figure out the msix_vector_count from the PCIe MSIX
capabilities register instead of the IOC Facts->MaxMSIxVectors. This is
because the firmware is not filling in this field until the driver has
already registered MSIX support.
(3) If the ioc_facts reports that the controller is MSIX compatible in the
capabilities, then the driver will request for multiple irqs. This count
is calculated based on the minimum between the online cpus available and
the ioc->msix_vector_count. This count is reported to firmware in the
ioc_init request.
(4) New routines were added _base_free_irq and _base_request_irq, so
registering and freeing msix vectors were done thru simple function API.
(5) The new routine _base_assign_reply_queues was added to align the msix
indexes across cpus. This will initialize the array called
ioc->cpu_msix_table. This array is looked up on every MPI request so the
MSIxIndex is set appropriately.
(6) A new shost sysfs attribute was added to report the reply_queue_count.
(7) User needs to set the affinity cpu mask, so the interrupts occur on the
same cpu that sent the original request.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/scsi/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
mpt2sas_base_detach() call was removed from _scsih_remove() while
doing some code shuffling. Mainly when we work on adding code for
scsih_shutdown(). I have added back mpt2sas_base_detach() which will
get callled from _scsih_remove().
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue:
This issue is seen on LSI H/W WarpDrive SSS6200 When filed direct I/O
is tried as volume I/O the scmd field in internal lookup table get
cleared and because of that the retried volume I/O never gets reported
as completed to SML.
Result:
I/O timeout and Error handling thread will kicking off
Fix:
Setting back the scmd in the lookup table before retrying the failed
direct i/o
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver should not call shutdown call from _scsih_remove otherwise,
The scsi midlayer can be deadlocked when devices are removed from the driver
pci_driver->shutdown handler.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Properly handling of target reset in multi-initiator environment
Clean up in broadcast change handling:
(1) Need to look at the status of each task management request, and retry
the TM when there are failures.
(2) Need quiescence IO so the driver doesn't take on more IO request while
it's in the middle of sending TM request to firmware
(3) Add support to keep track of how many pending broadcast AEN events
are received while the broadcast handling is active, then loop back at
the end of this routine if there were any events received.
Clean up in mpt2sas_scsih_issue_tm routine:
(1) Make sure proper status is returned when host reset fails
(2) Clean up sanity checks near end of routine, insuring all outstanding
IOs were completed.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This feature is to override the default
max_sectors setting at load time, taking max_sectors as an
command line option when loading the driver. The setting is
currently hard-coded in the driver to 8192 sectors (4MB transfers).
If max_sectors is specified at load time, minimum specified
setting will be 64, and the maximum is 8192. The driver will
modify the setting to be on even boundary. If max_sectors is not
specified, the driver will default to 8192.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch addresses many endian issues solved by runing sparse with the
option __CHECK_ENDIAN__ turned on.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Ensure that the initial reference tag is passed on to the HBA firmware
for DIF Type 2 devices.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Kashyap Desai <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Driver was a sending a SEP request during interrupt context which
required to go to sleep.
The fix is to rearrange the code so a fake event
MPT2SAS_TURN_ON_FAULT_LED is fired from interrupt context, then later
during the kernel worker threads processing, the SEP request is issued
to firmware.
Cc: stable@kernel.org
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch has Support for the new solid state device product SSS6200
from LSI and relavent features w.r.t SSS6200.
The major feature added in this driver is supporting Direct-I/O to the
SSS6200 storage.There are some additional changes done to avoid exposing
the RAID member disks to the OS and hiding/exposing drives based on the
OEM Specific Flag in Manufacturing Page10 (this is required to handle
specific changes in the SSS6200 firmware).
Each and every changes are listed below.
1. Hiding IR related messages.
For SSS6200, the driver is modified not to print IR related events.
Even if the debugging is enabled the IR related messages will not be displayed.
In some places if there is a need to display a message related to IR the
string "IR" is replaced with string "DD" and the string "volume" is replaced
with "direct drive". But the function names are not changed hence there are
some places where the reference to volume can be seen if debug level is set.
2. Removed RAID transport support
In Linux the user can retrieve RAID volume information from the sysfs directory.
This support is removed for SSS6200.
3. Direct I/O support.
The driver tries to enable direct I/O when a volume is reported to the driver
by the firmware through IRCC events and the driver does this just before
reporting to the OS, hence all the OS issued I/O can go through direct path
if they can, The first validation is to see whether the manufacturing page10
flag is set to expose all drives always. If that is set, the driver will not
enable direct I/O and displays the message "DDIO" is disabled globally as
drives are exposed. The driver checks whether there is more than one volume
in the controller, if so the direct I/O will be disabled globally for all
volumes in the controller and the message displayed will be "DDIO is disabled
globally as number of drives > 1.
If retrieving number of PD is failed the driver will not enable direct I/O
and displays the message Failure in computing number of drives DDIO disabled.
If memory allocation for RAIDVolumePage0 is failed, the driver will not enable
direct I/O and displays the message Memory allocation failure for
RVPG0 DDIO disabled. If retrieving RAIDVolumePage0 is failed the driver will
not enable direct I/O and displays the message Failure in retrieving
RVPG0 DDIO disabled
If the number of PD in a volume is greater than 8, then the direct I/O will
be disabled.
If any of individual drives handle retrieval is failed then the DD-IO will
be disabled.
If the volume is not RAID0 or if the block size is not 512 then the DD-IO will
be disabled.
If the volume size is greater than 2TB then the DD-IO will be disabled.
If the driver is not able to find a valid stripe exponent using the configured
stripe size then the DD-IO will be disabled
When the DD-IO is enabled the driver will check every I/O request issued to
the storage and checks whether the request is either
READ6/WRITE6/READ10/WRITE10, if it is and if the complete I/O transfer
is within a stripe size then the I/O is redirected to
the drive directly instead of the volume.
On completion of every I/O, if the completion is failure means if the reply
is address reply with a reply frame associated with it, then the type of I/O
will be checked, if the I/O is direct then the I/O will be retried to
the volume once.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Reviewed-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The SCSI midlayer stops all command processing when in error handling, which
means there is no chance for command reuse when the abort handler is called.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
Simple conversions to drop flush_scheduled_work() usages in
drivers/scsi. More involved ones will be done in separate patches.
* NCR5380, megaraid_sas: cancel_delayed_work() +
flush_scheduled_work() -> cancel_delayed_work_sync().
* mpt2sas_scsih: drop unnecessary flush_scheduled_work().
* arcmsr_hba, ipr, pmcraid: flush the used work explicitly instead of
using flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Issue:
IR shutdown(sending) and IR shutdown(complete) messages not
listed in /var/log/messages when driver is removed.
The driver needs to issue a MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED
request when the driver is unloaded so the IR metadata journal is updated.
If this request is not sent, then the volume would need a "check
consistency" issued on the next bootup if the volume was roamed from one
initiator to another. The current driver supports this feature only when the
system is rebooted, however this also need to be supported if the driver is
unloaded
Fix:
To fix this issue, the driver is going
to need to call the _scsih_ir_shutdown prior to reporting
the volumes missing from the OS, hence the device handles
are still present.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
False timeout after hard resets, there were two issues which leads
to timeout.
(1) Panic because of invalid memory access in the broadcast asyn
event processing routine due to a race between accessing the scsi command
pointer from broadcast asyn event processing thread and completing
the same scsi command from the interrupt context.
(2) Broadcast asyn event notifcations are not handled due to events
ignored while the broadcast asyn event is activity being processed
from the event process kernel thread.
In addition, changed the ABRT_TASK_SET to ABORT_TASK in the
broadcast async event processing routine. This is less disruptive to other
request that generate Broadcast Asyn Primitives besides target
reset. e.g clear reservations, microcode download,and mode select.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The "internal device reset complete" event is not supported
for older firmware prior to MPI Rev K We added
a check in the driver so the "internal device reset" event is
ignored for older firmware. When ignored, the tm_busy flag doesn't
get set nor cleared. Without this fix, IO queues would be froozen
indefinetly after the "internal device reset" event, as the "complete" event
never sent to clear the flag.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When zoning end devices, the driver is not sending device
removal handshake alogrithm to firmware. This results in controller
firmware not sending sas topology add events the next time the device is
added. The fix is the driver should be doing the device removal handshake
even though the PHYSTATUS_VACANT bit is set in the PhyStatus of the
event data. The current design is avoiding the handshake when the
VACANT bit is set in the phy status.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix oops loading driver when there is direct attached
SEP device
The driver set max phys count to the value reported in sas iounit page
zero. However this page doesn't take into account additional virutal
phys. When sas topology event arrives, the phy count is larger than
expected, and the driver accesses memory array beyond the end of
allocated space, then oops. Manufacturing page 8 contains the info
on direct attached phys.
For this fix will making sure that sas topology event is not
processing phys greater than the expected phy count.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
change_queue_depth callback API changed
The change_queue_depth callback changed where there is now an additional
parameter called reason, with SCSI_QDEPTH_DEFAULT, SCSI_QDEPTH_QFULL,
and SCSI_QDEPTH_RAMP_UP codes.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
remove support for MPI2_EVENT_TASK_SET_FULL
This event is obsoleted, so this processing of this event
needs to be removed from the driver. The controller firmware is going
to handle TASK_SET_FULL, the driver doesn't need to do anything.
Even though we are removing the EVENT handling, the behavour has not
changed between driver versions becuase fimrware will still be handling
queue throttling, and retrying of commands when the target device queues
are full.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Issue : Switch swap doesn't work when device missing delay is enabled.
(1) add support to individually add and remove phys to and from
existing ports. This replaces the routine
_transport_delete_duplicate_port.
(2) _scsih_sas_host_refresh - was modified to change the link rate
from zero to 1.5 GB rate when the firmware reports there is an
attached device with zero link.
(3) add new function mpt2sas_device_remove, this is wrapper function
deletes some redundant code through out driver by combining into one
subrountine
(4) two subroutines were modified so the sas_device, raid_device, and
port lists are traversed once when objects are deleted from the list.
Previously it was looping back each time an object was deleted from the
list.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Create a pool of chain buffers, instead of dedicated per IO:
This enahancment is to address memory allocation failure when asking
for more than 2300 IOs per host. There is just not enough contiquious
DMA physical memory to make one single allocation to hold both message
frames and chain buffers when asking for more than 2300 request. In order
to address this problem we will have to allocate memory for each chain
buffer in a seperate individual memory allocation, placing each chain
element of 128 bytes onto a pool of available chains, which can be
shared amoung all request.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The compiler throws warning messages while compiling without
CONFIG_SCSI_MPT2SAS_LOGGING.
Set proper ifdef for CONFIG_SCSI_MPT2SAS_LOGGING to avoid warnnings.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fixes surrounding PCIe enhanced error handling:
(1) We need to reject all request generated internaly inside the driver as well
as request arriving from the scsi mid layer when PCIe EEH is active. The fix is
to add a per adapter flag called pci_error_recovery which is checked thru out
the driver when request are generated.
(2) We don't need to call the pci_driver->remove directly from the PCIe
callbacks becuase its already called from the PCIe EEH code. In its place we are
shutting down the watchdog timer, and flushing back all pending IO.
(3) We need to save and restore the pci state across PCIe EEH handling.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adding additional messages to the error escallation callbacks which
displays the wwid, sas address, handle, phy number, enclosure logical id,
and slot. In the same eh callbacks, routines, the printks were converted
to sdev_printks, which displays the bus target mapping. These additional
modifications help better identify the device which is in recovery.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ISSUE DESCRIPTION:
This test case involves creating two RAID1 volumes, then
simultaneiously issue host reset and pull all the drives associated to
the 1st raid volume. The observed behavour is the physical drives are
removed, however the volume remains. The expected behavour is the
volume as well as physical drives should be removed from OS.
FIX:
Add support in the post host reset device scan logic for raid volumes
where the driver will have an additional check for responding raid
volume where the status should be either online, optimal, or degraded.
So for voluemes that have a status of missing or failed, the driver
will mark them for deletion.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Actual problem :
Driver may receiving the top level expander
removal event prior to all the individual PD removal events, hence the
driver is breaking down all the PDs in advanced to the actaul PD UNHIDE
event. Driver sends multiple
Target Resets to the same volume handle for each individual PD removal.
FIX DESCRIPTION:
To fix this issue, the entire PD device handshake protocal has to be
moved to interrupt context so the breakdown occurs immediately after the
actual UNHIDE event arrives. The driver will only issue one Target Reset to
the volume handle, occurring after the FAILED or MISSING volume status
event arrives from interrupt context. For the PD UNHIDE event, the driver
will issue target resets to the PD handles, followed by OP_REMOVE. The
driver will set the "deteleted" flag during interrupt context. A "pd_handle"
bitmask was introduced so the driver has a list of known pds during entire
life of the PD; this replaces the "hidden_raid_component" flag handle in
the sas_device object. Each bit in the bitmask represents a device handle.
The bit in the bitmask would be toggled ON/OFF when the HIDE/UNHIDE
events arrive; also this pd_handle bitmask would bould be refreshed
across host resets.
Here we kept older behavior of sending target reset to volume when there is
a single drive pull, wait for the reply, then send target resets
to the PDs. We kept this behavior so the driver will
behave the same for older versions of firmware.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support to display additional debug info for SCSI_IO and
RAID_SCSI_IO_PASSTHROUGH sent from the normal entry queued entry
point, as well as internal generated commands, and IOCTLS. The
additional debug info included the phy number, as well as the
sas address, enclosure logical id, and slot number. This debug info
has to be enabled thru the logging_level command line option, by
default this will not be displayed.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Converting print level from MPT2SAS_DEBUG_FMT to MPT2SAS_INFO_FMT.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Updating MPI header version N.
Removed mpi_history.txt.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver should not allow multiple host reset when already host reset is in
progress. It is possible that host reset was sent by scsi mid layer while there was already an host reset active,
either issued via IOCTL interface or internaly, like a config page timeout.
Since there was a host reset active, the driver would return a FAILED response
to the scsi mid layer. The solution is make sure pending host resets will
wait for the active host reset to complete before returning control
back up the call stack.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adding DIF Type 2 protection support, as well as turning on 32 byte cdb's,
and setting the cdb length for > 16 byte in the SCSI_IO->control parameter.
Signed-off-by: Martin Petersen <martin.petersen@oracle.com>
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix a oops in _scsih_sas_device_remove. The driver was attempting to
delete a object from the sas_device link list when the object was not
present.
Added sanity check for sas_device NULL dereference.
before deleting sas_device now driver will search device in list then
only it will follow device removal.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
we added support to set the deleted flag prior to device scan,
then clear the flag for responding devices, leaving the deleted flag only
set for missing devices. The problem is for internal generated host resets,
IO queues are not blocked at scsi mid layer level. IO will be continued
sent to driver, and driver will return SCSI_MLQUEUE_HOST_BUSY. The problem
is the driver checks for the deleted flag before it checks for the
controller being in reset, so there is a window where the driver would be
returning DID_NO_CONNECT for responding devices. This occurs during the
time between calling _scsih_prep_device_scan, and
_scsih_mark_responding_sas_device & _scsih_mark_responding_raid_device.
Fix the queuecommand entry point so ioc->shost_recovery flag sanity check is
given higher presidence then the device "deleted flag" check.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added support in the driver to support EEH and
PCIe Advanced Error Recovery. This involves adding new
pci_error_handler interface for recovering the controller from PCI Bus
errors, such as SERR and PERR. Some tools are available for simulating
PCI errors in order to validate this interface:
http://www.kernel.org/pub/linux/utils/pci/aer-inject
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After Host Reset firmware will have new list of device handles for the target.
Device handle refresh in driver is part of Rescan topology logic.
(See functions like *_search_responding_*). This needs to be done from Host
Reset context before making shost_recovery to 0. Currently it is done in
Firwmare event context, which may leads IO to a wrong device.
Now handler refresh is moved to HBA reset context.
Apart from this, Now driver will stop IOs for all device setting deleted
flag to 1 at the time of HBA Reset through _scsih_prep_device_scan.
It will only unblock devices, if devices has been found as part of RESCAN.
This way it will make more safe IO blocking at the time of HBA reset at
mpt2sas driver layer.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
RAID_SCSI_IO_PASSTHROUGH: Driver needs to be send the default
descriptor for RAID Passthru, currently its sending SCSI_IO descriptor.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Removed all the mutex's for ioc->tm_cmds.mutex, then created one
single mutex inside the function mpt2sas_scsih_issue_tm. This is the
single function used when sending task management. Also the sanity
checks required for scsi mid layer escalation were moved to inside the
same function because these checks need to be done while the mutex is
held. The ioc->tm_cmds.mutex inside the IOCTL branch is really not
required since there is another mutex in this code called for ctl_cmds
handling this sync.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1. Fixes for little endian issues.
2. Now Debug info for Discovery event is more readable.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Now Driver will not treat NEEDS_INIT as failure. In addition to this,
the driver will now display message to describe the the access flags
when bits are set, so the end user can better understand failures.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Aded checks for shost_recovery flag for early return from function.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bug fix in the handling of the internal device reset event
The reason code check in scsih_sas_device_status_change_event never
evaluates as true for internal device reset, hence driver never quiesce s IO
when firmware is sending a device reset. The fix is to change the
evaluate to:
if (event_data->ReasonCode !=
MPI2_EVENT_SAS_DEV_STAT_RC_INTERNAL_DEVICE_RESET &&
event_data->ReasonCode !=
MPI2_EVENT_SAS_DEV_STAT_RC_CMP_INTERNAL_DEV_RESET)
return;
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Setting handle to zero is not required before _scsih_remove_device.
Driver uses sas_device->handle reference in _scsih_remove_device.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
external host not connecting after controller reboot: The
problem is : devices are not coming back after having the cable
disconnected then reconnected. The problem is because the
driver/firmware device removal handshake is failing. Due to this failure,
the controller firmware is not sending out device add events when the target
is reconnected. This is root caused to a race in the driver/firmware device
removal algorithm. There is duplicate code in both interrupt and user
context; where target reset is being issue from user context path while
sas_iounit_control(OP_REMOVE) is being sent from interrupt context. An
active target_reset will fail the OP_REMOVE. To fix this problem, the
duplicate code has been removed from user context path.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
modified _scsih_sas_device_find_by_handle
so to handle the search on both list(device list and device_init_list)
Also, we moved the priority of the
search so the ioc->sas_device_list is done first. The
"sas_device_init_list" is only used during the 1st port enable, so its
unlikely there’s devices on it.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add the cancel_pending_work flag from the fw_event_work structure, and then to
set the flag during host reset, check the flag later from work threads
context and if cancel_pending_work_flag is set ingore those events.
Now Rescan after host reset is changed.
Added special task MPT2SAS_RESCAN_AFTER_HOST_RESET. This task will be queued
at the time of HBA reset. this task is treated as barrier. All work after
MPT2SAS_RESCAN_AFTER_HOST_RESET will be treated as new work and will be
server by callback handle. If host_recovery is going on while running RESCAN
task, it will wait for shos_recovery_done completion which will be called
from HBA reset DONE context.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
scsi_dma_map() returns -1 if an error occurred (zero means that the
command has no data). So the following current code can't catch an
error:
sges_left = scsi_dma_map(scmd);
if (!sges_left) {
sdev_printk(KERN_ERR, scmd->device, "pci_map_sg"
" failed: request for %d bytes!\n", scsi_bufflen(scmd));
return -ENOMEM;
}
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
For RAID volume sas_is_tlr_enabled call will hit BUG at
scsi_transport_sas.c:163, since raid volume
is not visible to sas transport layer.
Now Added check to make sure arg pass in sas_is_tlr_enabled() is not a volume.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If TLR is supported for end device, MPT2SAS driver will enable the TLR
bit in the SCSI_IO for every request. If there is a response with
MPI2_SCSITASKMGMT_RSP_INVALID_FRAME, the driver will turn off the TLR
logic.
[jejb: updated to new transport class TLR API]
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Adding support for raid transport layer. This will provide sysfs attributes
containing raid level, state, and resync rate.
MPT2SAS module will select RAID_ATTRS.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver hangs when doing `rmmod mpt2sas` if there are any
IR volumes present.The hang is due the scsi midlayer trying to access the
IR volumes after the driver releases controller resources. Perhaps when
scsi_remove_host is called,the scsi mid layer is sending some request.
This doesn't occur for bare drives becuase the driver is already reporting
those drives deleted prior to calling mpt2sas_base_detach.
To solve this issue, we need to delete the volumes as well.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) target resets are sending link change rate events with no link rate
change -> thus said the driver was modified so when there is no link rate
change, we don't need to call mpt2sas_transport_update_links nor
_scsih_ublock_io_device.
(2) There were changes made in _scsih_sas_topology_change_event_debug to
change the debug strings so they are more clear. Also the link rate change
information was added to display the new and previous link rate.
for the MPI2_EVENT_SAS_TOPOLOGY_CHANGE_LIST event when the ExpStatus is
set to zero, display "responding" instead of "unknown status".
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) Added new function _scsih_ir_shutdown. This function will issue the
MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED request via
MPI2_FUNCTION_RAID_ACTION. The function will wait 10 seconds for reply
message frame, then print out the ioc status and loginfo. This function is
only called when there are raid volumes present.
(2) Add shutdown callback in the struct pci_driver object scsih_driver. This
will be called only when the system is shutting down. From this function, we
will call _scsih_ir_shutdown mentioned above.
(3) Add support in _scsih_remove to call _scsih_ir_shutdown. The function
_scsih_remove will be called when the driver is unloaded (and system is
still running).
scsih internal command contex is added to send internal message frames
from mpt2sas_scsih.c.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When receiving the MPI2_EVENT_SAS_DEV_STAT_RC_INTERNAL_DEVICE_RESET event,
the driver will set the tm_busy flag in the sdev private host data, When
tm_busy flag is set, the driver will return SCSI_MLQUEUE_DEVICE_BUSY,
effectly freezing the IO to the device. The tm_busy flag is cleared with the
MPI2_EVENT_SAS_DEV_STAT_RC_CMP_INTERNAL_DEV_RESET event.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) EEDP(End to End data protection) was not working. This was due to not
setting EEDP BlockSize and Flags to little endian format in the message
frame.
(2) Some expander sysfs attributes were not getting set properly. The sas
format was not getting set due to endian issues with sas_format field in the
struct rep_manu_reply. Since sas_format was not set properly, the
component_vendor_id, component_revision_id, and component_id were not set.
(3) In _transport_smp_handler: we don't need to convert the smid from little
endian to cpu prior to calling mpt2sas_base_free_smid, because its allready
in cpu format. (4) Some loginfos and ioc status were not xonverted from
little endian to cpu.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
cpu_to_le64 when calculating the physical dma address. This will properly
handle endianess on big endian systems. The return value of this function
was changed from dma_addr_t to __le64. Remove the typecasting of u32 when
setting the SenseBufferLowAddress, since its already in __le32 format.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1 Its observed that the OS was sending request to the driver after it had been
put into blocking state, so the driver was modified to return
SCSI_MLQUEUE_DEVICE_BUSY.
2. Driver will return DID_TRANSPORT_DISRUPTED when sdev is haivng nexus loss.
This occurrs when sdev is blocked, between the
MPI2_EVENT_SAS_TOPO_RC_DELAY_NOT_RESPONDING and
MPI2_EVENT_SAS_TOPO_RC_TARG_NOT_RESPONDING events.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) for the MPI2_EVENT_IR_OPERATION_STATUS event, add support to print
"background init" or "make data consistent" for debugging purposes. If the
RAIDOperation is set to a value not defined, then don't print anything
(2) for the MPI2_EVENT_SAS_DEVICE_STATUS_CHANGE event, add support to print
"expander reduced functionality" and "expander reduced functionality
complete", which are new events.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added sanity check in _scsih_change_queue_depth to limit the max_depth to 32
for SATA devices. This is only for physical devices not part of a volume.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added command line option and shost sysfs attribute called
mpt2sas_fwfault_debug. When enduser writes a "1" to this parameter, this
will enable support in the driver for debugging firmware timeout related
issues. This handling was added in three areas (a) scsi error handling
callback called task_abort, (b) IOCTL interface, and (c) other timeouts that
result in diag resets, such as manufacturing config pages. When this
support is enabled, the driver will provide dump_stack to console, halt
controller firmware, and panic driver. The end user probably would want to
setup serial console redirection so the dump stack can be seen.
Here are the three methods for enable this support:
(a) # insmod mpt2sas.ko mpt2sas_fwfault_debug=1
(b) # echo 1 > /sys/module/mpt2sas/parameters/mpt2sas_fwfault_debug
(c) # echo 1 > /sys/class/scsi_host/host#/fwfault_debug (where # is
the host number)
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support in the driver to check for valid response info in the scsi
state, then check to see if the response code is
MPI2_SCSITASKMGMT_RSP_INVALID_FRAME; when this condition occurrs, the driver
will return DID_SOFT_ERROR. A return code of DID_SOFT_ERROR will result in
a retry at the scsi-mid layer level. An additional change added to obtain
the response code from the 1st byte of the response info instead of last.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This handles the case where driver receives a expander removal event while
it is in the middle of processing an expander add event. The existing
implementation will stop processing futher device adds when a expander
delete arrives on top of add expander add. Due to a sanity check in the
driver, the devices there were not added, were never handshaked to firmware
with the device removal handshake protocal. Since the driver didnt' do the
handshake, the controller never provide further add events. To fix this
issue, the sanity check was removed so the driver will always do the device
removal handshake protocal.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The device driver was not handling updating device handles in all cases
across diag resets. To fix this issue, the driver is converted to using sas
address instead of handle as a lookup reference to the parent expander or
sas_host. Also, for both expanders and sas host, the phy handle will be one
unique handle. In the sas host case, the phy handle can be different for
every phy, so the change is to set the handle to the handle of the first
phy; every phy will be one single sas address(phy 0) instead of a different
sas address for every phy(previous implementation). So making one consistent
sas address for all the direct attachedports to the sas host, will make it
better user experience when using udev /dev/disk/by-path dev nodes
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support to process device removal events when the phy status is set to
MPI2_EVENT_SAS_TOPO_PHYSTATUS_VACANT.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
(1) Added three new functions to handle sending target resest and OP_REMOVE
from interrupt time, they are _scsih_tm_tr_send, _scsih_tm_tr_complete, and
_scsih_sas_control_complete. This code will create a link list of pending
target resets if there is no more available request in the hipriority
request queue. The list is stored in ioc->delayed_tr_list.
(2) All callback handler return type is changed from void to u8.
Now _base_interrupt will check for return type of callback handlers to
take decision of message frame is already freed or not.
In genral,
Return 1 meaning mf should be freed from _base_interrupt
0 means the mf is freed from function.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
1) create a pool of high priority message frames in the region of memory
between message frames and chains. The modifications are in
_base_allocate_memory_pools. Also create a seperate pool of memory for
internal commands located near the same region of memory. The pool of high
priority message frames is restriced by the facts->HighPriorityCredit.
2) Create additional API for accessing request message frames. New function
mpt2sas_base_get_smid_hpr is for highpriority request. New function
mpt2sas_base_get_smid_scsiio for SCSI_IO, passing in the scsi command
pointer. The mpt2sas_base_get_smid function is for requesting internal
commands.
3) Added new function _base_get_cb_idx to obtain the callback
index from one of the three pools of request message frames.
4) Removed wrapper functions _scsih_scsi_lookup_set and
_scsih_scsi_lookup_getclear. These were removed because this handling was
moved into mpt2sas_base_get_smid_scsiio and mpt2sas_base_free_smid.
5) The function mpt2sas_base_free_smid is modified so the request message
frames are put back on one of the three pools of request message frames.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update the copyright year to 2009 through out the code.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Drivers header are updated to the MPI2 REV K headers.
Renamed VF_ID to msix_index in all call back handlers.
VF_ID is removed from all request descriptor.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cleaned up base_interrupt routine to be more effiecent.
Deleted about a third of the config page API by moving redundant code from all
the calling functions to _config_request.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch modifies the slave_configure callback so the messages that get sent
to system log for RAID1E volumes contain the string "RAID10" instead of
"RAID1E". These messages contain information regarding what kind of scsi device
is being added. Certain OEMS can enable displaying the RAID10 string instead of
RAID1E via manufacturing page 10. The driver will read this config page at
driver load time, then determine from the GenericFlags0 bits whether display
the RAID10 or RAID1E string, also even drive count is taken into consideration.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Changing SDEV Running state from interrupt context. Previously It was
handle in work queue thread. With this change It will not wait for work
queue thread to execute scsih_ublock_io_device to put SDEV into Running
state. This will reduce delay for Device becoming RUNNING.
Modified this patch considering James comment "Not to change SDEV state
using scsi_device_set_state API, instead use scsi_internal_device_unblock
scsi_internal_device_block API"
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Deleted the wrapper function called _scsih_link_change. This function was
implemented for compatibility reasons only, between different kernel versions.
Currently this function is no longer needed. The calling function are
converted to calling mpt2sas_transport_update_phy_link_change directly in the
transport layer.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch renames the flag for indicating host reset from
ioc_reset_in_progress to shost_recovery. It also removes the spin locks
surrounding the setting of this flag, which are unnecessary. Sanity checks on
the shost_recovery flag were added thru out the code so as to prevent sending
firmware commands during host reset. Also, the setting of the shost state to
SHOST_RECOVERY was removed to prevent deadlocks, this is actually better
handled by the shost_recovery flag.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Following host reset its possible that the controller firmware could
assign new handles for devices, as well as adding or deleting devices. There is
code in the driver that will rescan the topology folowing host reset; updating
device handles, and remove devices that are no longer responding. This patch
will improve the responsivness by moving this rescaning from the delayed hotplug
worker thread to immediately following the host reset.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix oops ocurring at hibernation time. This oops was due to the firmware fault
watchdog timer still running after we freed resources. To fix the issue we need
to terminate the watchdog timer at hibernation time.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Inhibit 0x3117 loginfos - during cable pull, there are too many printks going
to the syslog, this is have impact on how fast the interrupt routine can handle
keeping up with command completions; this was the root cause to the config
pages timeouts.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When a volume is activated, the driver will recieve a pair of ir config change
events to remove the foreign volume, then add the native.
In the process of the removal event, the hidden raid componet is removed from
the parent.When the disks is added back, the adding of the port fails becuase
there is no instance of the device in its parent.
To fix this issue, the driver needs to call mpt2sas_transport_update_links()
prior to calling _scsih_add_device. In addition, we added sanity checks on
volume add and removal to ignore events for foreign volumes.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kernel panic is seen because driver did not tear down the port which should
be dnoe using mpt2sas_transport_port_remove(). without this fix When expander
is added back we would oops inside sas_port_add_phy.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kernel panic is seen because of enclosure_handle received from FW is zero.
Check is introduced before calling mpt2sas_config_get_enclosure_pg0.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
nagalakshmi.nandigama@lsi.com