To share code with some of the newer parts such as the S3C2416, move
parts of arch/arm/mach-s3c2443/clock.c to a common file called
arch/arm/plat-s3c24xx/s3c2443-clock.c.
Update the build configuration to deal with this new file.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Extend the ARMv5 ID code to deal with S3C2416 being built with
S3C2412/S3C2413 enabled, as these have their ID registers in a
different place.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add arch/arm/mach-s3c2416 for support of the Samsung S3C2416 SoC.
This patch adds support of the S3C2416 SoC, clocks, timers,
and initial IRQ support (without support of secondary set of registers).
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
[ben-linux@fluff.org: removed files to be reworked, fixed conflicts]
[ben-linux@fluff.org: use s3c2443 reset instead of specific reset code]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add s3c_disable_clocks() and change the clock registration code to use
the s3c_register_clocks() followed by s3c_disable_clocks() instead of
the loops it was using.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change s3c2410_gpio_setpin() and s3c2410_gpio_pullup() to use
the new s3c_ gpio configuration calls until all their users
are converted.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the necessary 1,2 and 4 bit configuration read calls for the new
gpio code to allow removal of the old s3c24xx gpio code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove s3c2410_gpio_getirq() as the only users is the pm code, and it
can be replicated by using gpio_to_irq().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the implementation of s3c2410_gpio_setcfg() as it should now be
functionally equivalent to s3c_gpio_cfgpin(), and add a wrapper for those
drivers that are still using this call.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The s3c_gpio_cfgpin() call should be functionally equivalent, so replace
the s3c2410_gpio_cfgpin() calls in the s3c24xx code with s3c_gpio_cfgpin
to allow moving away from a fixed GPIO number to register address mapping
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start moving code that is using the old s3c2410_gpio API to using the
newer s3c_gpio variants by finding all the usages of s3c2410_gpio_pullup()
which disable the pin's pull up and replacing them.
sed 's/s3c2410_gpio_pullup\(.*\), 1/s3c_gpio_cfgpull\1, S3C_GPIO_PULL_NONE/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the GPIO banks that are used on the S3C2443 and above to the
list of available GPIOS.
Currently we do not have any limit on the SoC GPIO, so these are
being registered whether the SoC has them or not. It is currently
up to the user not to try and use them.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for s3c_gpio_setcfg() and s3c_gpio_setpull() implementations
to get ready for removal of the specific code being used by s3c24xx.
Also rename the s3c_gpio_setcfg_s3c24xx_banka to s3c_gpio_setcfg_s3c24xx_a
as seen in the header file to correct a build warning.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The s3c24xx_mci_set_platdata() is init time only, so should
be marked as __init
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
[ben-linux@fluff.org: update description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Setting s3c2410fb_mach_info displays field with a struct marked as __initdata
means it won't be available later for ioctls like FBIOPUT_VSCREENINFO and they
will fail. Copying in s3c24xx_fb_set_platdata() is fixing this issue.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
Commit 58bac7b8de failed to move the two
PLL files s3c2440-pll-12000000.c and s3c2440-pll-16934400.c, so place
these in arch/arm/mach-s3c2440 to fix this commit up.
As a note, these are not built by the default configuration and thus the
failure to move wasn't spotted until much later.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Without resources description driver fails during initialization.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Continue the clearout of plat-s3c by moving audio-simtec.h to plat-s3c24xx
as there are no current implementations outside of this platform.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the Kconfig entries from plat-s3c to plat-samsung and plat-s3c24xx
as necessary. The S3C_BOOT entries and the DMA configuration can go to
plat-samsung. The low-level UART configurations are currently S3C2XX
specific and can go to plat-s3c24xx.
Eliminating plat-s3c from the build process will be submitted seperately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
dma-plat.h is the last file left in plat-s3c64xx, but to remove it we
must also change the use of dma-plat.h by the core code and the s3c24xx
implementation.
Rename the s3c24xx dma-plat.h in the common plat-samsung directory as it
may be used for other ports. Move the specific dma bits into the
mach-s3c64xx directory and update the build as needed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merge these two headers into one, these two SoCs are so similar.
Note, correct fault in mach-smdk2443.h including the wrong header.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the old common S3C2440 and S3C2442 SoC support from plat-s3c24xx
into mach-s3c2440 now this directory is serving both SoCs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rename mach-s3c2410/include/mach/gpio-core.h to mach/gpio-track.h so that
it can be included by <plat/gpio-core.h> when needed.
Eliminate all other empty gpio-core.h files and just include the
<plat/gpio-core.h> as necessary.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a s3c24xx_mci_set_platdata() call for all the machine files that have
platform data for the MCI driver. This brings the MCI device into line with
the other devices with __initdata and a specific call to ensure the right
structure type is being passed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move s3c24xx_uart_devs, s3c24xx_uart_src and the platform devices to a
common entry in plat-samsung since they are the same in all the current
implementations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Reduce the size of struct clk by 12 bytes and make defining clocks with
common implementation functions easier by moving the set_rate, get_rate,
round_rate and set_parent calls into a new structure called 'struct clk_ops'
and using that instead.
This change does make a few clocks larger as they need their own clk_ops,
but this is outweighed by the number of clocks with either no ops or having
a common set of ops.
Update all the users of this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add definition for the touchscreen driver platform data and initial
support for the H1940 machine.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 's3c24xx-updates' of git://git.fluff.org/bjdooks/linux:
ARM: S3C24XX: DMA: Use valid index when accessing array
ARM: S3C: move s3c_pwm_remove to .devexit.text
ARM: S3C24XX: Export s3c24xx_set_fiq for modules.
ARM: S3C: move s3c_adc_remove to .devexit.text
The DMA_CH_VALID bit used in the channel index should be masked out before
using it to access the channel array.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Allow s3c24xx_set_fiq() to be exported so that it can be used by modules
wanting FIQ support.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The function s3c_adc_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-By: Ben Dooks <ben@simtec.co.uk>
Cc: Ramax Lo <ramaxlo@gmail.com>
Cc: Nelson Castillo <arhuaco@freaks-unidos.net>
Cc: linux-kernel@vger.kernel.org
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
There are a number of statements of the form A, B or A, B, C where
the numbers A,B,C are not consecutive. However, referencing [1] it
is the correct thing to replace these with A-B or A-C as apropriate.
[1] http://www.copyrightservice.co.uk/copyright/p03_copyright_notices
section 4iii 'Year of publication'
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
There are a number of statements of the form A, B or A, B, C where
the numbers A,B,C are consecutive. Tidy these up to be A-B or A-C
as appropriate and to comply better with copyright standards [1]
[1] http://www.copyrightservice.co.uk/copyright/p03_copyright_notices
section 4iii 'Year of publication'
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add documentation for the platform data structure in the SD/MMC driver
header file arch/arm/plat-s3c24xx/include/plat/mci.h.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the platform/machine support for the audio devices fitted to
the Simtec range of boards since the move to ASoC.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following warnings from sparse in arch/arm/plat-s3c24xx/gpio.
due to the missing include of <mach/gpio-fns.h>
gpio.c:36:6: warning: symbol 's3c2410_gpio_cfgpin' was not declared. Should it be static?
gpio.c:84:14: warning: symbol 's3c2410_gpio_getcfg' was not declared. Should it be static?
gpio.c:103:6: warning: symbol 's3c2410_gpio_pullup' was not declared. Should it be static?
gpio.c:125:5: warning: symbol 's3c2410_gpio_getpull' was not declared. Should it be static?
gpio.c:138:6: warning: symbol 's3c2410_gpio_setpin' was not declared. Should it be static?
gpio.c:157:14: warning: symbol 's3c2410_gpio_getpin' was not declared. Should it be static?
gpio.c:184:5: warning: symbol 's3c2410_gpio_getirq' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If the NULL test on buf is needed, then the dereference should be after the
NULL test.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the export of s3c_adc_read.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
[ben-linux@fluff.org: remove unexport of s3c_adc_start, needed for ts]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the link errors if cpu-frequency support is enabled on s3c2410 systems
but there is no CONFIG_S3C2410_IOTIMING set. Fix this by ensuring the
relevant symbols are defined NULL if the code is not being built in.
Fixes the following error:
arch/arm/mach-s3c2410/built-in.o: undefined reference to `s3c2410_iotiming_get'
arch/arm/mach-s3c2410/built-in.o: undefined reference to `s3c2410_iotiming_set'
arch/arm/mach-s3c2410/built-in.o: undefined reference to `s3c2410_iotiming_calc'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the S3C2442B CPU ID to aid support the Openmoko GTA02 / Freerunner.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
[ben-linux@fluff.org: edit description for clarity and S3C2442B as uppercase]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Define a macro to avoid the following error during kernel build process
for platforms other than s3c2410:
arch/arm/plat-s3c24xx/cpu.c:84: error: ‘s3c2410a_init’ undeclared here (not in a function)
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Add better support for omitting either the card detect or the write
protect GPIOs if the board does not support it. Add the fields
no_wprotect and no_detect to the platform data which when set indicate the
absence of the respective GPIOs.
Note, this also fixes a minor bug where it tries to free IRQ0 if there is
no detect gpio available.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a selection for the data transfer mode of the s3cmci driver, allowing
for either a configuration or rumtime selection of the use of the DMA or
PIO transfer code.
The PIO only mode is 476 bytes smaller than the driver with both methods
compiled in.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the S5PC100 does not define S3C_PA_NAND, leaving the NAND device
definitions in arch/arm/plat-s3c/dev-nand.c unbuildable. Add a KConfig
entry to select whether this is built.
As backwards compatibility, both the S3C24XX and S3C64XX define the new
configuration in their main Kconfig files until better support for basing
this selection on a per-machine basis can be sorted out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add configuration callback for SPI bus 1 on GPD[8..10] and ensure the
correct GPIO configuration register definitions in regs-gpio.h
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the definition of the "generic" IRQ in the process.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for routing an IRQ from the normal ARM IRQ mechanism to the
FIQ input of the processor.
Note, also fix a bug where the init_FIQ() function has not been called
when CONFIG_FIQ is enabled.
Signed-off-by; Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The s3c64xx devices use the same hardware core as s3c24xx, so move
the timer/pwm handling to plat-s3c so it can be used by both.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the s3c_device_nand platform device from plat-s3c24xx to plat-s3c,
now that the nand driver also support the s3c64xx devices.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The pwm hardware only checks the compare register after a decrement,
so the pin never toggles if tcmp = tcnt.
This happens when a very low duty cycle is requested. Fix it by always
ensuring that tcmp < tcnt.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add debugfs support for the cpufreq driver to allow
information about the system state to be exported to
the user.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a sysdev S3C2410A sysdev to allow the differentiation
of the S3C2410A from the S3C2410. This is needed for the
CPUFREQ code to enable the extra features and update cpu
specific information.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add entries to select the crystal to select for each different
supported board. This information is then available for anything
else requiring this, such as the CPUFreq PLL tables.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add io-timing support for frequency scaling on the S3C2410 SoC.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the structure s3c_cpufreq_config from cpu-freq.h to the
less advertised cpu-freq-core.h as it is not needed by anything
outside the core drivers.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the core of the support for enabling the CPUFreq driver on
all S3C24XX based systems.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
To add HWMON support, we need a synchronous read() call that blocks
until completion. Add the client that is being service to the select
and convert callbacks to make the code easier.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change the hwmon device name to something more generic as this
should be functional for both the s3c24xx and s3c64xx archs.
Since it has yet to have a driver, it is pretty safe to change
as there are no extant users.
Also add the necessary entry in devs.h which seems to have been
missed out at somepoint.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The commit ec976d6eb0
removed a number of gpio definitions from <mach/hardware.h>
but misssed updating these two files:
Fix the following build errors by including <linux/gpio.h>:
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c: In function 's3c24xx_spi_gpiocfg_bus1_gpg5_6_7':
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c:25: error: implicit declaration of function 's3c2410_gpio_cfgpin'
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c:28: error: implicit declaration of function 's3c2410_gpio_pullup'
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c: In function 's3c24xx_spi_gpiocfg_bus0_gpe11_12_13':
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c:25: error: implicit declaration of function 's3c2410_gpio_cfgpin'
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c:28: error: implicit declaration of function 's3c2410_gpio_pullup'
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
CONFIG_S3C24XX_PWM was defined in arch/arm/plat-s3c24xx/Kconfig but
not used anywhere else as the corresponding makefile used
CONFIG_HAVE_PWM (selected by CONFIG_S3C24XX_PWM) to compile the PWM
driver.
Change the makefile to use CONFIG_S3C24XX_PWM to compile this driver
to ensure it is only build when needed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The arch_initcall() is too late for board initialisation to use
gpiolib when doing their machine specific initilisation via the
.init_machine callback.
Bring the file into line with the s3c64xx implementation and use
the core_initcall() to register the GPIO chips.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Several GPIO functions have been returning -1 to indicate
an error instead of returning a proper error code. Change
to return -EINVAL for invalid argument(s).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Prepare to remove the large number of S3C2410_GPxn defines
by moving to S3C2410_GPx(n) in arch/arm.
The following perl was used to change the files:
perl -pi~ -e 's/S3C2410_GP([A-Z])([0-9]+)([^_^0-9])/S3C2410_GP\1\(\2\)\3/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C24XX_GPIO_BASE makes it difficult to compress the
GPIO number space, and is only used in a few places of
which everything outside arch/arm/plat-s3c24xx/gpiolib.c
will be removed as soon as possible.
Change gpiolib.c to use the S3C2410_GPxCON register addresses
as the base for each bank, thus eliminating S3C24XX_GPIO_BASE.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In our recent changes, arch/arm/plat-s3c24xx/gpiolib.c needs
to have <linux/sysdev.h> included for it to build.
This fixes the following error/warnings:
arch/arm/plat-s3c/include/plat/pm.h:104: error: expected declaration specifiers or '...' before 'pm_message_t'
arch/arm/plat-s3c/include/plat/pm.h:104: warning: 'struct sys_device' declared inside parameter list
arch/arm/plat-s3c/include/plat/pm.h:104: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/plat-s3c/include/plat/pm.h:105: warning: 'struct sys_device' declared inside parameter list
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The use of S3C2410_GP[A-Z]x_INP and S3C2410_GP[A-Z]x_OUTP are
very rare and are taking up large amounts of space in the
regs-gpio.h header.
The GPIO layer has had generic input and out defines called
S3C2410_GPIO_INPUT and S3C2410_GPIO_OUTPUT for a while which work
for all S3C24XX GPIOs.
Do the following replacements:
S3C2410_GP[A-Z][0-9]*_\OUTP => S3C2410_GPIO_OUTPUT
S3C2410_GP[A-Z][0-9]*_\INP => /S3C2410_GPIO_INPUT
S3C2410_GPA[0-9]*_OUT => S3C2410_GPIO_OUTPUT
to remove any usages of these and prepare the header for
the removal of these.
The following command was used to acheive this:
find . -type f -writable ! -name regs-gpio.h ! -name "*~" | xargs sed -i~ -e 's/S3C2410_GP[A-Z][0-9]*_\OUTP/S3C2410_GPIO_OUTPUT/g' -e 's/S3C2410_GP[A-Z][0-9]*_\INP/S3C2410_GPIO_INPUT/g' -e 's/S3C2410_GPA[0-9]*_OUT/S3C2410_GPIO_OUTPUT/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the s3c2410_gpio_irq2pin() function as it is not being
used in any in kernel driver and the function is probably not
being used anywhere else.
This is also part of the effort to remove any of the s3c24xx gpio
specific code that cannot be recreated by using the gpiolib
framework now in the kernel.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
convert callback
This patch allow us to efficiently modify the number of
remaining conversions from the client side. This us useful
when we do not know in advance how many conversions we will
need or when we need to cancel pending conversions.
This change is simple enough to be compatible with existing
code that can just define the new pointer in the callback
and ignore it.
Sample usage:
http://tinyurl.com/s3c2410-ts-c (function stylus_adc_action).
Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix unused code warning in arch/arm/plat-s3c24xx/dma.c if there
is no PM support enabled. The function to_dma_chan() should
be marked inline so that the compiler will eliminate it without
warning if it isn't used.
arch/arm/plat-s3c24xx/dma.c:1239: warning: 'to_dma_chan' defined but not used
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the GPIO suspend/resume support inline with the gpiolib support
so that it will work with both the S3C24XX and S3C64XX series.
The s3c_gpio_chip is extended to have a pm callback and a save block
to keep the state of the GPIO over suspend, and the code from the
s3c24xx implementation is added to a new common file.
The suspend process now uses the list of registered chips to go through
saving and restoring each one as appropriate, using the pm callback to
select the appropriate routine depending on the type of control register
present.
This change also means that any additional GPIO added should not require
changes to the PM.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a simple debug message on saving the UART state and add a per-arch
pre-restore function to be used by the s3c64xx restore code to ensure
the UARTs control registers do not go through any illegal state changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The USB host base address is available on both the S3C24XX and S3C64XX
ranges.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add common definition for USB OHCI platform device, add a Kconfig
to selectively compile it and add update all the users.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change the name of S3C2410_DMA_CHANNELS to S3C_DMA_CHANNELS in the process.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The <plat/dma-regs.h> pre-date the invention of the TAB character,
so fix the indentation of the register defines.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The <mach/dma.h> is for the driver API for the DMA system and should
not have anything relying on the CPU specific registers.
Remove the registers to <plat/dma-regs.h> for the code that really
needs to know about them.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
calls
The S3C24XX DMA API channel configuration registers are being passed
values comprised of register values which makes it hard to move the
API to cover both the S3C24XX and S3C64XX.
These values can be calculated from knowing which device the channel
is connected to, so remove them from the two calls s3c2410_dma_config
and s3c2410_dma_devconfig.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the platform dma.h to dma-plat.h to ensure it doen't get
confused with plat/dma.h
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Check pending queue and remove the adc client being released.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The symbol 's3c_adc_try' in arch/arm/plat-s3c24xx/adc.c
does not need to be exported and thus should be static.
This fixes the following sparse warning:
adc.c:103:6: warning: symbol 's3c_adc_try' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix the following sparse error generated by including
<plat/gpio-core.h> instead of <mach/gpio-core.h>
gpiolib.c:78:22: warning: symbol 's3c24xx_gpios' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not. There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().
This patch fixes things to pass this string to arch_reset(). This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As noted by Russell King, the sleep code path is not
elegant and makes use of leaving items on the stack
between calls.
Change the code that does the following:
if (s3c_cpu_save(regs_save) == 0) {
flush_cache_all();
S3C_PMDBG("preparing to sleep\n");
pm_cpu_sleep();
}
to simply call s3c_cpu_save, and let that do the
necessary calls to quiesce and sleep the system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change the way the UART state is saved over suspend to allow the s3c64xx
code to modify the settings on resume to avoid any illegal state changes
to the UART clocks. This will also allow us to save the UDIVSLOT register
on newer SoCs.
Move to using a structure for the UART use the extant Kconfig configuration
specifying the number of UARTs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rename s3c2410_cpu_resume to s3c_cpu_resume and s3c2410_cpu_save to
s3c_cpu_save to remove the CPU specific naming of these functions
which are now in the generic PM code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Since we have moved a large proportion of the PM code to the common
support area, remove the cpu specific name from the initialisation
function.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the IRQ_EINT sleep control to be available to all
s3c impelmentations. Since s3c_irqext_wake is not large,
place it in arch/arm/plat-s3c/pm.c as adding it to a new
file would be a waste of compile time.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Split the PM code out of arch/arm/plat-s3c24xx/irq.c to
remove some of the #ifdefs being used. Also fix a couple
of places where the absecnce of a function was redefined
to the same thing.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Split the optional memory check code out of the pm.c file
as it is quite a big #ifdef block and as-such can be moved
out and simply compiled when the configuration is set.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start moving the PM code by moving all the common support functions
to a common location in arch/arm/plat-s3c. With the move we rename
the functions from s3cxxx_ to s3c_ to fit the new location.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the <plat/pm.h> header to plat-s3c as preparation
for moving parts of the s3c24xx pm support which are
common into the plat-s3c support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the IIS headers to their correct place.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per Russell King's last review comment, find and remove
all unnecessary includes of <linux/delay.h> in the files
that do not need them.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the fourth UART definition for the S3C2443, and at the
same time fixup the problems caused by the enlarging of the
UART array in the previous commits.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A common core driver for the S3C24XX ADC block so that
the touchscreen, hwmon and any other drivers can share
the resource.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C64XX timer is running at the wrong rate due to the
assumptions made in the timer initialisation about the way
the pwm dividers work. This means that time on the S3C64XX
runs twice as fast as it should.
Fix the problem by moving to using the clk framework to setup
the pwm timer clock muxes, as the pwm-clock code has all the
necessary knowledge of how the timer clock inputs are routed.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The S3C64XX series has a new TCFG divider setting to allow the clock
directly through, which means that we need to update the pwm-clock
code to cope with this.
Add <mach/pwm-clock.h> containing the specific code to deal with the
TCFG divider settings and provide any other per-arch data that the
pwm-clock driver needs to function.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the definition for the hsmmc device to plat-s3c
to be shared between the s3c24xx and s3c64xx platforms.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Initial architecture support for the S3C24A0 ARCH_S3C24A0.
We don't yet add an kconfig entry in the main arch/arm/Kconfig
file as the series is not complete, so that is left until enough
support is in to be useful.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Split the map.h definitions into common S3C24XX code by
adding arch/arm/plat-s3c24xx/include/plat/map.h and
altering the machine specific header for the S3C24A0.
As we add a new <plat/map.h> we move the original one
in arch/arm/plat-s3c include directory to be called
map-base.h to distinguish the two files.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
All the s3c24xx gpiolib chips share the same get/set
calls and all but one bank shares the same calls for
.direction_input and .direction_output methods.
Change the initialisation process to use an new call
to register the chips that fills in any blank calls
with the default values to avoid having to fill them
in the structure initialisers.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the core clock registration and definitions
in arch/arm/plat-s3c24xx/clock.c to arch/arm/plat-s3c
to be shared with the S3C64XX implementations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Ben Dooks