On OMAP4+ platforms the functional clock for the McPDM IP is suplied by
the twl6040 codec (bit clock on the PDM bus).
This common clock driver for twl6040 will register the mcpdm_fclk clock to
be used by the McPDM driver to make sure that the needed clocks are
available when needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In case of error, the function clk_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In case of error, the function clk_register_fixed_rate() returns
ERR_PTR() not NULL pointer. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
For u8500 and using 100MHz as the frequency also requires the ape opp 100
voltage, thus use the prcmu_opp_volt_scalable clock type.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some scalable prcmu clocks needs to be handled in conjuction with the
ape opp 100 voltage. A new prcmu clock type clk_prcmu_opp_volt_scalable
is implemented to handle this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some of the helper functions return negative error codes if
passed a NULL clock. This can lead to confusing behavior when the
expected return value is unsigned. Fix up these accessors so that
they return unsigned values (or bool in the case of is_enabled).
This way we can't interpret NULL clocks as having valid and
interesting values.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Currently we are getting following warning for SPEAr clk-vco-pll.
"warning: i is used uninitialized in this function."
This is because we are getting value of i by passing its pointer to another
routine.
The variables here are really not used uninitialized.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Fix typo in message reported when unable to lookup the uart1 clock.
Signed-off-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
No framework work here, only a bunch of driver updates of varying sizes:
- Factoring out of the core hardware support from the MXS MMC driver by
Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ld23
-----END PGP SIGNATURE-----
Merge tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi updates from Mark Brown:
"No framework work here, only a bunch of driver updates of varying
sizes:
- Factoring out of the core hardware support from the MXS MMC driver
by Marek Vasut to allow the hardware to also be used for SPI.
- Lots of error handling cleanups from Guenter Roeck
- Removal of the existing Tegra driver which is quite comprehensively
broken as detailed in the changelog for the removal.
- DT suppport for the PL022 and GPIO drivers.
- pinctrl support for OMAP and PL022."
Pulling from Mark Brown as Grant Likely is still busy moving.
* tag 'spi-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc: (53 commits)
spi: remove completely broken Tegra driver
spi/imx: set the inactive state of the clock according to the clock polarity
spi/pl022: get/put resources on suspend/resume
spi/pl022: use more managed resources
spi/pl022: Devicetree support w/o platform data
spi/s3c64xx: Don't free controller_data on non-dt platforms
spi: omap2-mcspi: add pinctrl support
spi/pl022: adopt pinctrl support
spi: omap2-mcspi: Cleanup the omap2_mcspi_txrx_dma function
spi/gpio: Fix stub for spi_gpio_probe_dt()
spi/mxs: Make the SPI block clock speed configurable via DT
spi: spi-sh-hspi: drop frees of devm_ alloc'd data
spi/pl022: Fix chipselects pointer computation
spi: spi-tle62x0: Use module_spi_driver macro
mxs/spi: Rework the mxs_ssp_timeout to be more readable
mxs/spi: Decrement the DMA/PIO border
mxs/spi: Increment the transfer length only if transfer succeeded
mxs/spi: Fix issues when doing long continuous transfer
spi: spi-gpio: Add DT bindings
spi: spi-gpio: store chipselect information in private structure
...
This branch converts the MXS Freescale platform to use irqdomains and
sparse IRQ, in preparation for DT probing and multiplatform kernels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wVa3
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc-specific updates, take 2 from Olof Johansson:
"This branch converts the MXS Freescale platform to use irqdomains and
sparse IRQ, in preparation for DT probing and multiplatform kernels."
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: remove mach/irqs.h
ARM: mxs: select SPARSE_IRQ
ARM: mxs: adopt irq_domain support for icoll driver
ARM: mxs: select MULTI_IRQ_HANDLER
ARM: mxs: retrieve timer irq from device tree
gpio/mxs: adopt irq_domain support for mxs gpio driver
Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=q7ZY
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc device tree updates from Olof Johansson:
"Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8."
Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
arm: vt8500: Fixup for missing gpio.h
ARM: LPC32xx: LED fix in PHY3250 DTS file
ARM: dt: mmp-dma: add binding file
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
...
Most notable here is probably the addition of basic support for the
BCM2835, an SoC used in some of the Roku 2 players as well as the
much-hyped Raspberry Pi, cleaned up and contributed by Stephen
Warren. It's still early days on mainline support, with just the
basics working. But it has to start somewhere!
Beyond that there's some conversions of clock infrastructure on tegra
to common clock, misc updates for several other platforms, and OMAP
now has its own bus (under drivers/bus) to manage its devices through.
This branch adds two new directories outside of arch/arm:
drivers/irqchip for new irq controllers, and drivers/bus for the above
OMAP bus. It's expected that some of the other platforms will migrate
parts of their platforms to those directories over time as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=BCp4
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc-specific updates from Olof Johansson:
"Most notable here is probably the addition of basic support for the
BCM2835, an SoC used in some of the Roku 2 players as well as the
much-hyped Raspberry Pi, cleaned up and contributed by Stephen Warren.
It's still early days on mainline support, with just the basics
working. But it has to start somewhere!
Beyond that there's some conversions of clock infrastructure on tegra
to common clock, misc updates for several other platforms, and OMAP
now has its own bus (under drivers/bus) to manage its devices through.
This branch adds two new directories outside of arch/arm:
drivers/irqchip for new irq controllers, and drivers/bus for the above
OMAP bus. It's expected that some of the other platforms will migrate
parts of their platforms to those directories over time as well."
Fix up trivial conflicts with the clk infrastructure changes.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (62 commits)
ARM: shmobile: add new __iomem annotation for new code
ARM: LPC32xx: Support GPI 28
ARM: LPC32xx: Platform update for devicetree completion of spi-pl022
ARM: LPC32xx: Board cleanup
irqchip: fill in empty Kconfig
ARM: SAMSUNG: Add check for NULL in clock interface
ARM: EXYNOS: Put PCM, Slimbus, Spdif clocks to off state
ARM: EXYNOS: Add bus clock for FIMD
ARM: SAMSUNG: Fix HDMI related warnings
ARM: S3C24XX: Add .get_rate callback for "camif-upll" clock
ARM: EXYNOS: Fix incorrect help text
ARM: EXYNOS: Turn off clocks for NAND, OneNAND and TSI controllers
ARM: OMAP: AM33xx hwmod: fixup SPI after platform_data move
MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
ARM: bcm2835: instantiate console UART
ARM: bcm2835: add stub clock driver
ARM: bcm2835: add system timer
ARM: bcm2835: add interrupt controller driver
ARM: add infra-structure for BCM2835 and Raspberry Pi
ARM: tegra20: add CPU hotplug support
...
ports to the framework along with one MIPS port, one MFD port, one minor
framework enhancement and one helper function for platforms expressing
their clock data through device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQadDCAAoJEDqPOy9afJhJCvcQAMVvkmom7aROkXfn6V3pxlUq
dAtwpzvmikzdrE/4wMAus38o04Lygk6vEdXIJZyood1WTxBNbl+C9SJPg0ZmN8P+
0I2Vx6u7ZoHggeG44s3ziDTVBC/+MolDlXlgJrqG7SHyLRGzHF4W6BDLvSUHzMcq
zoFFAQPSx2TKfSkHHNj3PKdWX/vFOSZL5tkMU5QMNCC3kYyd9j+StaiIRAN0V7Nz
kHy2tdkEA323E6fTwHlFOwBi/CjddIdVLZQr1DVIjwdmKfuf45hglZYULNbvPwOF
AB8hyVFMozA44GKi+92u3NZ0TIrirctVDiK6k3UcD2tcgRNjrFHwQpe4ogg6/S58
U+AXM62fsWhA6vykBgNadbeGhsIvfI8HJdRqjULxfqLkQsqNCAGjINJJbTC9Mev/
zGfi3vjAUbbC0nAOmDloD93x8JI+P75IQC4GJD6FuHgoW7rDlKs+z9FXzJh/0W5T
fQCnjLaPMnPv1VYWToGy0aCBGLpDhbTJNPqVA4SZBJQ5u2XXXLr8BjpavcG6ns5j
zmXWVJo6Y+X7rU5+0RH3VGhnUylFEvQZyEa1O3rnNoNfy4Q9ymA/G27iZC5OPklw
mSH4N+ndX6hT+KM+gDL9t6gyhkIhyhUSoQCRpWKAFqihYR2ckRPFUcK6OvqsA7JH
vQMNdm2fW4zYSTsvT3mP
=7v8L
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clk framework update from Michael Turquette:
"The common clk framework changes for 3.7 are dominated by ARM platform
ports to the framework along with one MIPS port, one MFD port, one
minor framework enhancement and one helper function for platforms
expressing their clock data through device tree."
* tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: add of_clk_src_onecell_get() support
clk: ux500: Define smp_twd clock for u8500
mfd: dbx500: Provide a more accurate smp_twd clock
clk: ux500: Support for prmcu_rate clock
clk: Provide option for clk_get_rate to issue hw for new rate
clock: max77686: Add driver for Maxim 77686 32Khz crystal oscillator.
ARM: ux500: Switch to use common clock framework
clk: ux500: Clock definitions for u8500
clk: ux500: First version of clock definitions for ux500
clk: ux500: Adapt PRCMU and PRCC clocks for common clk
clk: versatile: make config option boolean
clk: add Loongson1B clock support
arm: mmp: make all SOCs use common clock by default
clk: mmp: add clock definition for mmp2
clk: mmp: add clock definition for pxa910
clk: mmp: add clock definition for pxa168
clk: mmp: add mmp specific clocks
clk: convert ARM RealView to common clk
clk: prima2: move from arch/arm/mach to drivers/clk
ARM: PRIMA2: convert to common clk and finish full clk tree
remove existing non-dt code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQXBatAAoJEAKiPfwuf9N/VZoIAI7PKNwakjM/KDiVzytwqZ+U
h9kkjYW4ra8MH+jpjFQqvSyIJ3U+t016xqW3ZbqRuZBDgH0I7Gax7QoAZ/ljPlpG
RAKl2l9WVPiBSwCESTpvR5lafBLklk6fL0Z267qIxDGld6YBiWHvTKIh1zDmeCWW
hgDeWtcb1M61VlPrj9nPnCze66h2dUk+QSxaCodv7co5kzb0Q4S7U64BCs0hGe01
kkdoUwnBjdeK0cUhDAJAP1vRyk04N16+H7yp4npmKhv/blKVc3MIRjg1iBV78ncd
Kke/G1B9TJRpNTXdySYnsDQpaCWNSAryKXKkdxP0gh6MW8CMKYc1mdKYcEP3Tk8=
=xG1+
-----END PGP SIGNATURE-----
Merge tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code into next/dt
From Tony Prisk:
Update arch-vt8500 and drivers to device tree and
remove existing non-dt code.
* tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code:
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
Resolved add/change conflict in drivers/clk/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds common clock framework support for arch-vt8500.
Support for PLL and device clocks on VT8500, WM8505 and WM8650
are included.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Mike Turquette <mturquette@linaro.org>
This patch adds a minimal stub clock driver for the BCM2835. Its sole
purpose is to allow the PL011 AMBA clk_get() API calls to provide
something that looks enough like a clock that the driver probes and
operates correctly.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:
* Reworked to call clk_register_fixed_rate(), and clk_register_clkdev()
rather than using static data to represent the clocks.
* Moved implementation to drivers/clk/.
* Modified .dev_id for UART clocks to match UART DT node names.
* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Surprisingly devres_destroy() doesn't call the destructor for the
resource it is destroying, use the newly added devres_release() instead
to fix this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The managed clk functions are currently only available when the generic clk
lookup framework is build. But the managed clk functions are merely wrappers
around clk_get and clk_put and do not depend on any specifics of the generic
lookup functions and there are still quite a few custom implementations of the
clk API. So make the managed functions available whenever the clk API is
implemented.
The patch also removes the custom implementation of devm_clk_get for the
coldfire platform.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It replaces clk_register_clkdev in mxs clock driver with DT lookup.
The series depends on pull request mxs-dt-3.7 and Mike's clk branch
below.
git://git.linaro.org/people/mturquette/linux.git clk-3.7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQTvyZAAoJEFBXWFqHsHzO3kEIAKsT3i7vdriXVAityIMiC1el
pVDR2qVq0q7+MhCIO/wXWbjJBHK+vEiMY2sKWCD4jVfLCa751mwENAdf1h1/+NNZ
+W6uzRaMt3w4FGryn4/xXt4eVgZNNZba9NxE73tVSanK9oJilPwBLCCkwbZLFbjk
SughytSMml1uO8Z3mEG0DDmrCnwb1KsILasVLazTGA1gpQ02c+6ASPa8s0App6/2
DLkIOn6D3022LzQiIungxUc4wLBojylex/GCAPubyhX3pXyjlzUElp4G3AFex8KM
tMnuXBfpi1dLkgYPn+rkM8m48dCY821LxFT9OA3AfpzqVpRWU6Kcq60vNzUDnt0=
=scyJ
-----END PGP SIGNATURE-----
Merge tag 'mxs-clk-dt-lookup' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
It replaces clk_register_clkdev in mxs clock driver with DT lookup.
* tag 'mxs-clk-dt-lookup' of git://git.linaro.org/people/shawnguo/linux-2.6:
clk: mxs: replace imx23 clk_register_clkdev with clock DT lookup
clk: mxs: replace imx28 clk_register_clkdev with clock DT lookup
It really becomes a maintenance issue that every time a device needs
to look up (clk_get) a clock we have to patch kernel clock file to call
clk_register_clkdev for that clock.
Since clock DT support which is meant to resolve clock lookup in device
tree is in place, the patch moves imx23 client devices' clock lookup
over to device tree, so that any new lookup to be added at later time
can just get done in DT instead of kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It really becomes a maintenance issue that every time a device needs
to look up (clk_get) a clock we have to patch kernel clock file to call
clk_register_clkdev for that clock.
Since clock DT support which is meant to resolve clock lookup in device
tree is in place, the patch moves imx28 client devices' clock lookup
over to device tree, so that any new lookup to be added at later time
can just get done in DT instead of kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
For those SoCs that have hundreds of clock outputs, their clock
DT bindings could reasonably define #clock-cells as 1 and require
the client device specify the index of the clock it consumes in the
cell of its "clocks" phandle.
Add a generic of_clk_src_onecell_get() function for this purpose.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The smp_twd clock is based upon a prcmu_rate clock type
for the PRCMU_ARMSS clock.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The prmcu_rate clock is not gateable and has a rate which
only can be fetched.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
By using CLK_GET_RATE_NOCACHE flag, we tell the clk_get_rate API to
issue the hw for an updated clock rate. This can be used for a clock
which rate may be updated without a client necessary modifying it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch supports max77686 mfd's clock driver using common clock frame work.
max77686 has 3 clock ouputs which all are generated from crystal oscillator and
SOC can enable/disable them via I2C bus. All clocks are fixed-rate clock sources
so that it doesn't supply interface for changing clock rate.
Driver uses regmap API to communicate with internal register.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Remove machine specific clock implementation and switch to use
new common clock framework.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
First version of clock definitions of PRCMU and PRCC clocks
for the u8500 platform.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In this first version of the clock definitions, the structure for
ux500 are set. Support for u8500, u9540 and u8540 are prepared.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
First version of common clock implementation of PRCMU clocks
and PRCC clocks for ux500 platforms.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
There is no choice to have the RealView clocks as module for sure,
so turn this config option into a boolean.
Reported-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Rather than using the static timer irq definition, we should retrieve
timer irq from device tree for better.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds clock support to Loongson1B SoC using the common clock
infrastructure.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This converts the ARM RealView machine over to using the common
clock. The approach is similar to the one used for the Integrator,
and we're reusing the ICST wrapper code.
We have to put the clock intialization in the timer init function
for the clocks to be available when initializing the timer,
keeping them in early_init() is too early for the common clk.
Since we now have to go down and compile drivers/clk/versatile
a CONFIG_COMMON_CLK_VERSATILE symbol has been added so the proper
code gets compiled into the kernel for either machine. A leftover
CLK_VERSATILE in the Integrator Kconfig was fixed up to use
the new symbol as well.
Tested on ARM RealView PB1176.
Cc: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Pull out the MMC clock configuration function and make it
into SSP clock configuration function, so it can be used by
the SPI driver too.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
clk_get() returns -ENOENT on error and some careless caller might
dereference it without error checking:
In mxc_rnga_remove():
struct clk *clk = clk_get(&pdev->dev, "rng");
// ...
clk_disable(clk);
Since it's insane to audit the lots of existing and future clk users,
let's add a check in the callee to avoid kernel panic and warn about
any buggy user.
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
menu "Common Clock Framework" has "depends on COMMON_CLK" and so configs
defined within menu don't require these "depends on COMMON_CLK again".
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
framework improvments, platform ports and new DT bindings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=V8ad
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull common clk framework changes from Michael Turquette:
"This includes a small number of core framework improvments, platform
ports and new DT bindings."
Fix up trivial conflicts in drivers/clk/Makefile
* tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux: (21 commits)
clk: fix compile for OF && !COMMON_CLK
clk: fix clk_get on of_clk_get_by_name return check
clk: mxs: clk_register_clkdev mx28 usb clocks
clk: add highbank clock support
dt: add clock binding doc to primecell bindings
clk: add DT fixed-clock binding support
clk: add DT clock binding support
ARM: integrator: convert to common clock
clk: add versatile ICST307 driver
ARM: integrator: put symbolic bus names on devices
ARM: u300: convert to common clock
clk: cache parent clocks only for muxes
clk: wm831x: Add initial WM831x clock driver
clk: Constify struct clk_init_data
clk: Add CLK_IS_BASIC flag to identify basic clocks
clk: Add support for rate table based dividers
clk: Add support for power of two type dividers
clk: mxs: imx28: decrease the frequency of ref_io1 for SSP2 and SSP3
clk: mxs: add clkdev lookup for pwm
clk: mxs: Fix the GPMI clock name
...
This adds support for three new SoC types:
* The mvebu platform includes Marvell's Armada XP and Armada 370 chips,
made by the mvebu business unit inside of Marvell. Since the same
group also made the older but similar platforms we call "orion5x",
"kirkwood", "mv78xx0" and "dove", we plan to move all of them into
the mach-mvebu directory in the future.
* socfpga is Altera's platform based on Cortex-A9 cores and a lot of
FPGA space. This is similar to the Xilinx zynq platform we already
support. The code is particularly clean, which is helped by the fact
that the hardware doesn't do much besides the parts that are
expected to get added in the FPGA.
* The OMAP subarchitecture gains support for the latest generation,
the OMAP5 based on the new Cortex-A15 core. Support is rather
rudimentary for now, but will be extended in the future.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=MwdJ
-----END PGP SIGNATURE-----
Merge tag 'newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull support for three new arm SoC types from Arnd Bergmann:
- The mvebu platform includes Marvell's Armada XP and Armada 370 chips,
made by the mvebu business unit inside of Marvell. Since the same
group also made the older but similar platforms we call "orion5x",
"kirkwood", "mv78xx0" and "dove", we plan to move all of them into
the mach-mvebu directory in the future.
- socfpga is Altera's platform based on Cortex-A9 cores and a lot of
FPGA space. This is similar to the Xilinx zynq platform we already
support. The code is particularly clean, which is helped by the fact
that the hardware doesn't do much besides the parts that are expected
to get added in the FPGA.
- The OMAP subarchitecture gains support for the latest generation, the
OMAP5 based on the new Cortex-A15 core. Support is rather
rudimentary for now, but will be extended in the future.
* tag 'newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
ARM: socfpga: initial support for Altera's SOCFPGA platform
arm: mvebu: generate DTBs for supported SoCs
ARM: mvebu: MPIC: read number of interrupts from control register
arm: mach-mvebu: add entry to MAINTAINERS
arm: mach-mvebu: add compilation/configuration change
arm: mach-mvebu: add defconfig
arm: mach-mvebu: add documentation for new device tree bindings
arm: mach-mvebu: add support for Armada 370 and Armada XP with DT
arm: mach-mvebu: add source files
arm: mach-mvebu: add header
clocksource: time-armada-370-xp: Marvell Armada 370/XP SoC timer driver
ARM: Kconfig update to support additional GPIOs in OMAP5
ARM: OMAP5: Add the build support
arm/dts: OMAP5: Add omap5 dts files
ARM: OMAP5: board-generic: Add device tree support
ARM: omap2+: board-generic: clean up the irq data from board file
ARM: OMAP5: Add SMP support
ARM: OMAP5: Add the WakeupGen IP updates
ARM: OMAP5: l3: Add l3 error handler support for omap5
ARM: OMAP5: gpmc: Update gpmc_init()
...
Conflicts:
Documentation/devicetree/bindings/arm/omap/omap.txt
arch/arm/mach-omap2/Makefile
drivers/clocksource/Kconfig
drivers/clocksource/Makefile
This is stuff that does not fit well into another category and in
particular is not related to a particular board. The largest part
in here is extending the am33xx support in the omap platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Qclg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific updates from Arnd Bergmann:
"This is stuff that does not fit well into another category and in
particular is not related to a particular board. The largest part in
here is extending the am33xx support in the omap platform."
Fix up trivial conflicts in arch/arm/mach-{imx/mach-mx35_3ds.c, tegra/Makefile}
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (74 commits)
ARM: LPC32xx: Add PWM support
ARM: LPC32xx: Add PWM clock
ARM: LPC32xx: Set system serial based on cpu unique id
ARM: vexpress: Config option for early printk console
ARM: vexpress: Add Device Tree for V2P-CA15_CA7 core tile
ARM: vexpress: Convert V2P-CA15 Device Tree to 64 bit addresses
ARM: vexpress: Add fixed regulator for SMSC
ARM: vexpress: Add missing SP804 interrupt in motherboard's DTS files
ARM: vexpress: Initial common clock support
ARM: SAMSUNG: Introduce Kconfig variable for Samsung custom clk API
ARM: EXYNOS: Add missing static storage class specifier in pmu.c file
ARM: EXYNOS: Make combiner_init function static
ARM: EXYNOS: Update HSOTG PHY clock setting for EXYNOS4X12
ARM: versatile: Make plat-versatile clock optional
ARM: vexpress: Check master site in daughterboard's sysctl operations
ARM: vexpress: remove automatic errata workaround selection
ARM: LPC32xx: Adjust to pl08x DMA interface changes
ARM: EXYNOS: Clear SYS_WDTRESET bit to use watchdog reset
ARM: imx: fix mx51 ehci setup errors
ARM: imx: make ehci power/oc polarities configurable
...
With commit 766e6a4ec6 (clk: add DT clock binding support),
compiling with OF && !COMMON_CLK is broken.
Reported-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Reported-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The commit 766e6a4 (clk: add DT clock binding support) plugs device
tree clk lookup of_clk_get_by_name into clk_get, and fall on non-DT
lookup clk_get_sys if DT lookup fails.
The return check on of_clk_get_by_name takes (clk != NULL) as a
successful DT lookup. But it's not the case. For any system that
does not define clk lookup in device tree, ERR_PTR(-ENOENT) will be
returned, and consequently, all the client drivers calling clk_get
in their probe functions will fail to probe with error code -ENOENT
returned.
Fix the issue by checking of_clk_get_by_name return with !IS_ERR(clk),
and update of_clk_get and of_clk_get_by_name for !CONFIG_OF build
correspondingly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Tested-by: Marek Vasut <marex@denx.de>
Tested-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
sys_clk has multiple parents and selection of parent depends on sys_clk_ctrl
register bit no. 23:25, with following possibilities
0XX: pll1_clk
10X: sys_synth_clk
110: pll2_clk
111: pll3_clk
Out of several possibilities (h/w wise) to select same clock parent for
sys_clk, current clock implementation was considering just one value.
When bootloader programmed different (valid) value to select a clock
parent then Linux breaks.
Here, we try to include all possibilities which can lead to same
clock selection thus making Linux independent of bootloader selection
values.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch is to fix typing mistake of clk enable register of i2c1 and
uart1.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The max limit of con_id is 16 and dev_id is 20. As of now for spear6xx, many clk
ids are exceeding this predefined limit.
This patch is intended to rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
ras_gen1_synth_gate_clk -> ras_syn1_gclk
pll3_48m -> pll3_
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The max limit of con_id is 16 and dev_id is 20. As of now for spear3xx, many clk
ids are exceeding this predefined limit.
This patch is intended to rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
ras_gen1_synth_gate_clk -> ras_syn1_gclk
ras_pll3_48m -> ras_pll3_
pll3_48m -> pll3_
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The max limit of con_id is 16 and dev_id is 20. As of now for spear1310, many
clk ids are exceeding this predefined limit.
This patch is intended to rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
gmac_phy -> phy_
gmii_125m_pad -> gmii_pad
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The max limit of con_id is 16 and dev_id is 20. As of now for spear1340, many
clk ids are exceeding this predefined limit.
This patch rename clk ids like:
mux_clk -> _mclk
gate_clk -> _gclk
synth_clk -> syn_clk
gmac_phy -> phy_
gmii_125m_pad_ -> gmii_pad
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This adds real clock support to Calxeda Highbank SOC using the common
clock infrastructure.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
[mturquette@linaro.org: fixed up invalid writes to const struct member]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for DT "fixed-clock" binding to the common fixed rate clock
support.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[Rob Herring] Rework and move into common clock infrastructure
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Based on work 1st by Ben Herrenschmidt and Jeremy Kerr, then by Grant
Likely, this patch adds support to clk_get to allow drivers to retrieve
clock data from the device tree.
Platforms scan for clocks in DT with of_clk_init and a match table, and
the register a provider through of_clk_add_provider. The provider's
clk_src_get function will be called when a device references the
provider's OF node for a clock reference.
v6 (Rob Herring):
- Return error values instead of NULL to match clock framework
expectations
v5 (Rob Herring):
- Move from drivers/of into common clock subsystem
- Squashed "dt/clock: add a simple provider get function" and
"dt/clock: add function to get parent clock name"
- Rebase to 3.4-rc1
- Drop CONFIG_OF_CLOCK and just use CONFIG_OF
- Add missing EXPORT_SYMBOL to various functions
- s/clock-output-name/clock-output-names/
- Define that fixed-clock binding is a single output
v4 (Rob Herring):
- Rework for common clk subsystem
- Add of_clk_get_parent_name function
v3: - Clarified documentation
v2: - fixed errant ';' causing compile error
- Editorial fixes from Shawn Guo
- merged in adding lookup to clkdev
- changed property names to match established convention. After
working with the binding a bit it really made more sense to follow the
lead of 'reg', 'gpios' and 'interrupts' by making the input simply
'clocks' & 'clock-names' instead of 'clock-input-*', and to only use
clock-output* for the producer nodes. (Sorry Shawn, this will mean
you need to change some code, but it should be trivial)
- Add ability to inherit clocks from parent nodes by using an empty
'clock-ranges' property. Useful for busses. I could use some feedback
on the new property name, 'clock-ranges' doesn't feel right to me.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Shawn Guo <shawn.guo@freescale.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This converts the Integrator platform to use common clock
and the ICST driver. Since from this point not all ARM
reference platforms use the clock, we define
CONFIG_PLAT_VERSATILE_CLOCK and select it for all platforms
except the Integrator.
Open issue: I could not use the .init_early() field of the
machine descriptor to initialize the clocks, but had to
move them to .init_irq(), so presumably .init_early() is
so early that common clock is not up, and .init_machine()
is too late since it's needed for the clockevent/clocksource
initialization. Any suggestions on how to solve this is
very welcome.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[mturquette@linaro.org: use 'select' instead of versatile Kconfig]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The ICST307 VCO clock has a shared driver in the ARM
architecture. This patch provides a wrapper into the common
clock framework so we can use the implementation in the
ARM architecture without duplicating the code until all
ARM platforms using this VCO are moved over. At that point
we can merge the driver from the ARM platform into the
generic file altogether.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[mturquette@linaro.org: removed versatile Kconfig]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This converts the U300 clock implementation over to use the common
struct clk and moves the implementation down into drivers/clk.
Since VCO isn't used in tree it was removed, it's not hard to
put it back in if need be.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[mturquette@linaro.org: trivial Makefile conflict]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
caching parent clocks makes sense only when a clock has more
than one parent (mux clocks).
Avoid doing this for every other clock.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[mturquette@linaro.org: removed extra parentheses]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The WM831x and WM832x series of PMICs contain a flexible clocking
subsystem intended to provide always on and system core clocks. It
features:
- A 32.768kHz crystal oscillator which can optionally be used to pass
through an externally generated clock.
- A FLL which can be clocked from either the 32.768kHz oscillator or
the CLKIN pin.
- A CLKOUT pin which can bring out either the oscillator or the FLL
output.
- The 32.768kHz clock can also optionally be brought out on the GPIO
pins of the device.
This driver fully supports the 32.768kHz oscillator and CLKOUT. The FLL
is supported only in AUTO mode, the full flexibility of the FLL cannot
currently be used.
Due to a lack of access to systems where the core SoC has been converted
to use the generic clock API this driver has been compile tested only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Most platforms end up using a mix of basic clock types and
some which use clk_hw_foo struct for filling in custom platform
information when the clocks don't fit into basic types supported.
In platform code, its useful to know if a clock is using a basic
type or clk_hw_foo, which helps platforms know if they can
safely use to_clk_hw_foo to derive the clk_hw_foo pointer from
clk_hw.
Mark all basic clocks with a CLK_IS_BASIC flag.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some divider clks do not have any obvious relationship
between the divider and the value programmed in the
register. For instance, say a value of 1 could signify divide
by 6 and a value of 2 could signify divide by 4 etc.
Also there are dividers where not all values possible
based on the bitfield width are valid. For instance
a 3 bit wide bitfield can be used to program a value
from 0 to 7. However its possible that only 0 to 4
are valid values.
All these cases need the platform code to pass a simple
table of divider/value tuple, so the framework knows
the exact value to be written based on the divider
calculation and can also do better error checking.
This patch adds support for such rate table based
dividers and as part of the support adds a new
registration function 'clk_register_divider_table()'
and a new macro for static definition
'DEFINE_CLK_DIVIDER_TABLE'.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Quite often dividers and the value programmed in the
register have a relation of 'power of two', something like
value div
0 1
1 2
2 4
3 8...
Add support for such dividers as part of clk-divider.
The clk-divider flag 'CLK_DIVIDER_POWER_OF_TWO' should be used
to define such clocks.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
SSP0 and SSP1 use ref_io0 which has decreased frequency. Expand
the frequency fix for ref_io1 to get SSP2 and SSP3 to work.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The below commit introduced a bug in __clk_set_parent()
which could cause it to *skip* the parent validation
which makes sure the parent passed to the api is a valid
one.
commit 7975059db5
Author: Rajendra Nayak <rnayak@ti.com>
Date: Wed Jun 6 14:41:31 2012 +0530
clk: Allow late cache allocation for clk->parents
This was identified by the following compiler warning..
drivers/clk/clk.c: In function '__clk_set_parent':
drivers/clk/clk.c:1083:5: warning: 'i' may be used uninitialized in this function [-Wuninitialized]
.. as reported by Marc Kleine-Budde.
There were various options discussed on how to fix this, one
being initing 'i' to clk->num_parents, but the below approach
was found to be more appropriate as it also makes the 'parent
validation' code simpler to read.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org
The correct name for the GPMI clock is 'gpmi-nand'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
rename the clock name from `8000c000.gpmi` to `8000c000.gpmi-nand`.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The struct clk_lookup are marked as __initdata, resulting in being
removed from memory after the kernel finished booting. However this
leads to a NULL pointer de-ref if loading a module which uses clk_get.
This patch removes the __initdata from the struct clk_lookup.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The definition of clocks ref_io0 and ref_io1 were inverted. It causes
a mmc regression on some boards right away. Fix the regression by
correcting the ref_io clock definition.
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_change_rate() is accessing parent's rate without checking
if the parent exists at all. In case of root clocks this will
cause NULL pointer dereference.
This patch follows what clk_calc_new_rates() does in such
situation.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org
Parent clocks for muxes are cached in clk->parents to
avoid frequent lookups, however the cache allocation happens
only during clock registeration and later clk_set_parent()
assumes a cache space available and allocated.
This is not entirely true for platforms which do early clock
registerations wherein the cache allocation using kzalloc
could fail during clock registeration.
Allow cache allocation to happen later as part of clk_set_parent()
to help such cases and avoid crashes assuming a cache being
available.
While here also replace existing kmalloc() with kzalloc()
in the file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove more custom stuff by simply converting the Nomadik machine
to use generic clocks and move the driver to drivers/clk.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the spear13xx platform, which has first been under
review a long time ago and finally been completed after generic spear
work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=W2Ri
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc: soc specific changes (part 2) from Olof Johansson:
"This adds support for the spear13xx platform, which has first been
under review a long time ago and finally been completed after generic
spear work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch."
Fix up trivial conflicts in drivers/gpio/gpio-samsung.c that look much
worse than they are: the exonys5 init code was refactored in commit
fd454997d6 ("gpio: samsung: refactor gpiolib init for exynos4/5"), and
then commit f10590c983 ("ARM: EXYNOS: add GPC4 bank instance") added a
new gpio chip define and did tiny updates to the init code.
So the conflict diff looks like hell, but it's actually a fairly simple
change.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: exynos: fix building with CONFIG_OF disabled
ARM: EXYNOS: Add AUXDATA for i2c controllers
ARM: dts: Update device tree source files for EXYNOS5250
ARM: EXYNOS: Add device tree support for interrupt combiner
ARM: EXYNOS: Add irq_domain support for interrupt combiner
ARM: EXYNOS: Remove a new bus_type instance for EXYNOS5
ARM: EXYNOS: update irqs for EXYNOS5250 SoC
ARM: EXYNOS: Add pre-divider and fout mux clocks for bpll and mpll
ARM: EXYNOS: add GPC4 bank instance
ARM: EXYNOS: Redefine IRQ_MCT_L0,1 definition
ARM: EXYNOS: Modify the GIC physical address for static io-mapping
ARM: EXYNOS: Add watchdog timer clock instance
pinctrl: SPEAr1310: Fix pin numbers for clcd_high_res
SPEAr: Update MAINTAINERS and Documentation
SPEAr13xx: Add defconfig
SPEAr13xx: Add compilation support
SPEAr13xx: Add dts and dtsi files
pinctrl: Add SPEAr13xx pinctrl drivers
pinctrl: SPEAr: Create macro for declaring GPIO PINS
SPEAr13xx: Add common clock framework support
...
These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WeDQ
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The clk_set_rate() code shouldn't check the clock's enable count when
validating CLK_SET_RATE_GATE flag since the enable count could change after
the validation. Similar to clk_set_parent(), it should instead check the
prepare count. The prepare count should go to zero only when the end user
expects the clock to not be enabled in the future. Since the code already
grabs the prepare count before validation, it's not possible for prepare
count to change after validation and by association not possible for a well
behaving end user to enable the clock while the set rate is in progress.
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
While there's no actual implementation behind it having the call to use
in drivers makes them feel neater from a driver author point of view. An
actual implementation can wait for someone who needs to use the function
in a real system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[mturquette@linaro.org: void return type instead of int -EINVAL]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds SPEAr1310 and SPEAr1340's clock framework support. It is based
on earlier support for SPEAr3xx family.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Mike Turquette <mturquette@ti.com>
The register HW_SSP_VERSION is broken for ssp version detection,
as the address of the register is different between imx23 and imx28.
Let's use platform_device_id to detect the device, so that the use
of cpu_is_xxx can be removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
SPEAr SoCs used its own clock framework since now. From now on they will move to
use common clock framework.
This patch updates existing SPEAr machine support to adapt for common clock
framework.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
All SPEAr SoC's contain GPT Synthesizers. Their Fout is derived from
following equations:
Fout= Fin/((2 ^ (N+1)) * (M+1))
This patch adds in support for this type of clock.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
All SPEAr SoC's contain Fractional Synthesizers. Their Fout is derived from
following equations:
Fout = Fin / (2 * div) (division factor)
div is 17 bits:-
0-13 (fractional part)
14-16 (integer part)
div is (16-14 bits).(13-0 bits) (in binary)
Fout = Fin/(2 * div)
Fout = ((Fin / 10000)/(2 * div)) * 10000
Fout = (2^14 * (Fin / 10000)/(2^14 * (2 * div))) * 10000
Fout = (((Fin / 10000) << 14)/(2 * (div << 14))) * 10000
div << 14 is simply 17 bit value written at register.
This patch adds in support for this type of clock.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
All SPEAr SoC's contain Auxiliary Synthesizers. Their Fout is derived based on
values of eq, x and y.
Fout from synthesizer can be given from two equations:
Fout1 = (Fin * X/Y)/2 EQ1
Fout2 = Fin * X/Y EQ2
This patch adds in support for this type of clock.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
All SPEAr SoC's contain PLLs. Their Fout is derived based on following equations
- In normal mode
vco = (2 * M[15:8] * Fin)/N
- In Dithered mode
vco = (2 * M[15:0] * Fin)/(256 * N)
pll_rate = vco/2^p
vco and pll are very closely bound to each other,
"vco needs to program: mode, m & n" and "pll needs to program p",
both share common enable/disable logic and registers.
This patch adds in support for this type of clock.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Rewrite mxs_dma_is_apbh and mxs_dma_is_apbx in order to support
other SoCs like imx6q and reform the platform_device_id for the
better further dt support.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Huang Shijie <b32955@freescale.com>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
It adds initial device tree support for imx23-evk board, and only
serial console is enabled.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
This patch includes basic dt support which can boot via nfs rootfs.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Shawn Guo <shawn.guo@linaro.org> writes:
mxs common clk porting for v3.5. It depends on the following two branches.
[1] git://git.linaro.org/people/mturquette/linux.git clk-next
[2] http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-arm.git clkdev
As the mxs device tree conversion will constantly touch clock files,
to save the conflicts, the updated mxs/dt branch coming later will
based on this pull-request.
* 'clk/mxs' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: remove now unused timer_clk argument from mxs_timer_init
ARM: mxs: remove old clock support
ARM: mxs: switch to common clk framework
ARM: mxs: change the lookup name for fec phy clock
ARM: mxs: request clock for timer
clk: mxs: add clock support for imx28
clk: mxs: add clock support for imx23
clk: mxs: add mxs specific clocks
Includes an update to Linux 3.4-rc6
Conflicts:
drivers/clk/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Having fixed factors/dividers in hardware is a common pattern, so
add a basic clock type doing this. It basically describes a fixed
factor clock using a nominator and a denominator.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
[mturquette@linaro.org: constify parent_names in static init macro]
[mturquette@linaro.org: copy/paste bug from mux in static init macro]
[mturquette@linaro.org: fix error handling in clk_register_fixed_factor]
[mturquette@linaro.org: improve division accuracy; thanks to Saravana]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The original conversion to struct clk_hw_init failed to add the pointer
assignment in clk_register_mux.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Exposing this option generates confusion and incorrect behavior for
single-image builds across platforms. Enable this behavior permanently.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Patch 'clk: always pass parent_rate into .round_rate' made a subtle
change to the semantics of .round_rate. It is now expected for the
parent's rate to always be passed in, simplifying the implemenation of
various .round_rate callback definitions.
However the patch also introduced a bug in clk_calc_new_rates whereby a
clock without the CLK_SET_RATE_PARENT flag set could still propagate a
rate change up to a parent clock if the the .round_rate callback
modified the &best_parent_rate value in any way.
This patch fixes the issue at the framework level (in
clk_calc_new_rates) by specifically handling the case where the
CLK_SET_RATE_PARENT flag is not set.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
With old mxs clock support removed, the timer_clk argument of
mxs_timer_init is unused now, so remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The common clock framework allocates clocks dynamically. Provide a
set of helpers to streamline the clkdev registration of the clock
lookups to avoid repetitive code sequences.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is well documented but isn't implemented. clk_set_rate() must check if
flags have CLK_SET_RATE_GATE bit set and is enabled too.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Create a struct clk_init_data to hold all data that needs to be passed from
the platfrom specific driver to the common clock framework during clock
registration. Add a pointer to this struct inside clk_hw.
This has several advantages:
* Completely hides struct clk from many clock platform drivers and static
clock initialization code that don't care for static initialization of
the struct clks.
* For platforms that want to do complete static initialization, it removed
the need to directly mess with the struct clk's fields while still
allowing to statically allocate struct clk. This keeps the code more
future proof even if they include clk-private.h.
* Simplifies the generic clk_register() function and allows adding optional
fields in the future without modifying the function signature.
* Simplifies the static initialization of clocks on all platforms by
removing the need for forward delcarations or convoluted macros.
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
[mturquette@linaro.org: kept DEFINE_CLK_* macros and __clk_init]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnd Bergman <arnd.bergmann@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Richard Zhao <richard.zhao@linaro.org>
Cc: Saravana Kannan <skannan@codeaurora.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Deepak Saxena <dsaxena@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Using the common clock infrastructure without the common clkdev code makes
little sense, so select CLKDEV_LOOKUP for COMMON_CLK.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
if (!clk->ops->round_rate && (clk->flags & CLK_SET_RATE_PARENT)) is true, then
we don't need to set clk->new_rate here, as we will call clk_calc_subtree()
afterwards and it also sets clk->new_rate.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch tries to remove duplicate code for clk_gate clocks. This creates
another routine clk_gate_endisable() which will take care of enable/disable
clock with knowledge of CLK_GATE_SET_TO_DISABLE flag.
It works on following logic:
For enabling clock, enable = 1
set2dis = 1 -> clear bit -> set = 0
set2dis = 0 -> set bit -> set = 1
For disabling clock, enable = 0
set2dis = 1 -> set bit -> set = 1
set2dis = 0 -> clear bit -> set = 0
So, result is always: enable xor set2dis.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Need to propagate round_rate call for the clk that has no .round_rate
operation but with flag CLK_SET_RATE_PARENT set.
For example, clk_mux is a clk with no .round_rate operation. However,
it could likely be in a clk_set_rate propagation path, saying it has
parent clk who has .round_rate and .set_rate operations.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
For most of .set_rate implementation, parent_rate will be used, so just
like passing parent_rate into .recalc_rate, let's pass parent_rate into
.set_rate too.
It also updates the kernel doc for .set_rate ops.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The parent_rate will likely be used by most .round_rate implementation
no matter whether flag CLK_SET_RATE_PARENT is set or not, so let's
always pass parent_rate into .round_rate.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch is the basic clk version of 'clk: core: copy parent_names &
return error codes'.
The registration functions are changed to allow the core code to copy
the array of strings and allow platforms to declare those arrays as
__initdata.
This patch also converts all of the basic clk registration functions to
return error codes which better aligns them with the existing clk.h api.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch cleans up clk_register and solves a few bugs by teaching
clk_register and __clk_init to return error codes (instead of just NULL)
to better align with the existing clk.h api.
Along with that change this patch also introduces a new behavior whereby
clk_register copies the parent_names array, thus allowing platforms to
declare their parent_names arrays as __initdata.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Drivers should be able to declare their arrays of parent names as const
so the APIs need to accept const arguments.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[mturquette@linaro.org: constified gate]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Most users of clk_get_rate() actually assume a non zero
return value as a valid rate returned. Returing -EINVAL
might confuse such users, so make it instead return zero
on error.
Besides the return value of clk_get_rate seems to be
'unsigned long'.
Signed-off-by: Rajendra nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clk_ops of basic clks should have "const" to match the definition
in "struct clk" and clk_register prototype.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It makes no sense to have EXPORT_SYMBOL_GPL on static functions.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Change clk_register_mux to use kzalloc, just like what all other basic
clk registration functions do.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Documentation/clk.txt has some handsome ASCII art outlining which
clk_ops are mandatory for a given clock, given the capability of the
hardware. Enforce those mandates with sanity checks in __clk_init.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It is possible to call clk_set_rate on a clock with a NULL parent. One
such example is an adjustable-rate root clock. Ensure that
clk_calc_new_rates does not dereference parent without checking first
and also handle the corner cases gracefully.
Reported-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some static inline dummy functions were left over from before the clock
core was consolidated from several C files down to one. Remove them.
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Remove old and misleading documentation from the previous clk_set_rate
implementaion.
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_find must return as soon as it gets the correct clock. Currently it check
all clocks until it found a lookup with both dev_id and con_id matching.
If only one of them is passed, then we don't actually need to wait for both of
them to match. We can quit as soon as the requested id (dev_id or con_id)
matches.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow clk API users to simplify their cleanup paths by providing a
managed version of clk_get() and clk_put().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All platforms that use the common clk infrastructure should select
COMMON_CLK from platform code, and on all other platforms, it must
not be enabled, so there is no point making the option visible to
users, and when it is visible, we break randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Many platforms support simple gateable clocks, fixed-rate clocks,
adjustable divider clocks and multi-parent multiplexer clocks.
This patch introduces basic clock types for the above-mentioned hardware
which share some common characteristics.
Based on original work by Jeremy Kerr and contribution by Jamie Iles.
Dividers and multiplexor clocks originally contributed by Richard Zhao &
Sascha Hauer.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnd Bergman <arnd.bergmann@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Richard Zhao <richard.zhao@linaro.org>
Cc: Saravana Kannan <skannan@codeaurora.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Deepak Saxena <dsaxena@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The common clock framework defines a common struct clk useful across
most platforms as well as an implementation of the clk api that drivers
can use safely for managing clocks.
The net result is consolidation of many different struct clk definitions
and platform-specific clock framework implementations.
This patch introduces the common struct clk, struct clk_ops and an
implementation of the well-known clock api in include/clk/clk.h.
Platforms may define their own hardware-specific clock structure and
their own clock operation callbacks, so long as it wraps an instance of
struct clk_hw.
See Documentation/clk.txt for more details.
This patch is based on the work of Jeremy Kerr, which in turn was based
on the work of Ben Herrenschmidt.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <rob.herring <at> calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Cc: Arnd Bergman <arnd.bergmann@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Richard Zhao <richard.zhao@linaro.org>
Cc: Saravana Kannan <skannan@codeaurora.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Deepak Saxena <dsaxena@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The commit 40d3e0f (clk: provide prepare/unprepare functions) provides
the config option HAVE_CLK_PREPARE for platforms that have
prepare/unprepare implementation to select. This patch adds the option
into drivers/clk/Kconfig, so that it can be actually selected.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Now most of ARM machines has the alsmot same __clk_get/put() macro
So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files
But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config
Now there are only 3 caese.
1) define the clk structure with clkdev macro => Need to move clk structure to proper header file
arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h
2) export the __clk_get/put function at clock.c
arch/arm/mach-shmobile/include/mach/clkdev.h
3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
clkdev may incorrectly cause a clkdev entry with a NULL clk to return
-ENOENT. This is not the intention of this code; -ENOENT should only
be returned if the clock entry can not be found in the table. Fix
this.
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Peter Ujfalusi