Need to get the endpoint reference before calling rdma_fini(), which
might fail causing us to not get the reference.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The max depth of a fastreg mr depends on whether the device supports
DSGL or not. So compute it dynamically based on the device support
and the module use_dsgl option.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a race when moving a QP from RTS->CLOSING where a SQ work
request could be posted after the FW receives the RDMA_RI/FINI WR.
The SQ work request will never get processed, and should be completed
with FLUSHED status. Function c4iw_flush_sq(), however was dropping
the oldest SQ work request when in CLOSING or IDLE states, instead of
completing the pending work request. If that oldest pending work
request was actually complete and has a CQE in the CQ, then when that
CQE is proceessed in poll_cq, we'll BUG_ON() due to the inconsistent
SQ/CQ state.
This is a very small timing hole and has only been hit once so far.
The fix is two-fold:
1) c4iw_flush_sq() MUST always flush all non-completed WRs with FLUSHED
status regardless of the QP state.
2) In c4iw_modify_rc_qp(), always set the "in error" bit on the queue
before moving the state out of RTS. This ensures that the state
transition will not happen while another thread is in
post_rc_send(), because set_state() and post_rc_send() both aquire
the qp spinlock. Also, once we transition the state out of RTS,
subsequent calls to post_rc_send() will fail because the "in error"
bit is set. I don't think this fully closes the race where the FW
can get a FINI followed a SQ work request being posted (because
they are posted to differente EQs), but the #1 fix will handle the
issue by flushing the SQ work request.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Some HW platforms can reorder read operations, so we must rmb() after
we see a valid gen bit in a CQE but before we read any other fields
from the CQE.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1) timedout endpoint processing can be starved. If there are continual
CPL messages flowing into the driver, the endpoint timeout
processing can be starved. This condition exposed the other bugs
below.
Solution: In process_work(), call process_timedout_eps() after each CPL
is processed.
2) Connection events can be processed even though the endpoint is on
the timeout list. If the endpoint is scheduled for timeout
processing, then we must ignore MPA Start Requests and Replies.
Solution: Change stop_ep_timer() to return 1 if the ep has already been
queued for timeout processing. All the callers of stop_ep_timer() need
to check this and act accordingly. There are just a few cases where
the caller needs to do something different if stop_ep_timer() returns 1:
1) in process_mpa_reply(), ignore the reply and process_timeout()
will abort the connection.
2) in process_mpa_request, ignore the request and process_timeout()
will abort the connection.
It is ok for callers of stop_ep_timer() to abort the connection since
that will leave the state in ABORTING or DEAD, and process_timeout()
now ignores timeouts when the ep is in these states.
3) Double insertion on the timeout list. Since the endpoint timers
are used for connection setup and teardown, we need to guard
against the possibility that an endpoint is already on the timeout
list. This is a rare condition and only seen under heavy load and
in the presense of the above 2 bugs.
Solution: In ep_timeout(), don't queue the endpoint if it is already on
the queue.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
[ Fix cast from u64* to integer. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add support for the block multicast loopback QP creation flag along
the proper firmware API for that.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As result of the deprecation of the MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block(), all drivers using these
two interfaces need to be updated to use the new
pci_enable_msi_range() or pci_enable_msi_exact() and
pci_enable_msix_range() or pci_enable_msix_exact() interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As result of the deprecation of the MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block(), all drivers using these
two interfaces need to be updated to use the new pci_enable_msi_range()
and pci_enable_msix_range() interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- The biggest change is core API extensions and mlx5 low-level driver
support for handling DIF/DIX-style protection information, and the
addition of PI support to the iSER initiator. Target support will be
arriving shortly through the SCSI target tree.
- A nice simplification to the "umem" memory pinning library now that
we have chained sg lists. Kudos to Yishai Hadas for realizing our
code didn't have to be so crazy.
- Another nice simplification to the sg wrappers used by qib, ipath and
ehca to handle their mapping of memory to adapter.
- The usual batch of fixes to bugs found by static checkers etc. from
intrepid people like Dan Carpenter and Yann Droneaud.
- A large batch of cxgb4, ocrdma, qib driver updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ww6H
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.15:
- The biggest change is core API extensions and mlx5 low-level driver
support for handling DIF/DIX-style protection information, and the
addition of PI support to the iSER initiator. Target support will
be arriving shortly through the SCSI target tree.
- A nice simplification to the "umem" memory pinning library now that
we have chained sg lists. Kudos to Yishai Hadas for realizing our
code didn't have to be so crazy.
- Another nice simplification to the sg wrappers used by qib, ipath
and ehca to handle their mapping of memory to adapter.
- The usual batch of fixes to bugs found by static checkers etc.
from intrepid people like Dan Carpenter and Yann Droneaud.
- A large batch of cxgb4, ocrdma, qib driver updates"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (102 commits)
RDMA/ocrdma: Unregister inet notifier when unloading ocrdma
RDMA/ocrdma: Fix warnings about pointer <-> integer casts
RDMA/ocrdma: Code clean-up
RDMA/ocrdma: Display FW version
RDMA/ocrdma: Query controller information
RDMA/ocrdma: Support non-embedded mailbox commands
RDMA/ocrdma: Handle CQ overrun error
RDMA/ocrdma: Display proper value for max_mw
RDMA/ocrdma: Use non-zero tag in SRQ posting
RDMA/ocrdma: Memory leak fix in ocrdma_dereg_mr()
RDMA/ocrdma: Increment abi version count
RDMA/ocrdma: Update version string
be2net: Add abi version between be2net and ocrdma
RDMA/ocrdma: ABI versioning between ocrdma and be2net
RDMA/ocrdma: Allow DPP QP creation
RDMA/ocrdma: Read ASIC_ID register to select asic_gen
RDMA/ocrdma: SQ and RQ doorbell offset clean up
RDMA/ocrdma: EQ full catastrophe avoidance
RDMA/cxgb4: Disable DSGL use by default
RDMA/cxgb4: rx_data() needs to hold the ep mutex
...
Unregister the inet notifier during ocrdma unload to avoid a panic after
driver unload.
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Clean up code. Also modifying GSI QP to error during ocrdma_close is fixed.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Issue mailbox commands to query ocrdma controller information and phy
information and print them while adding ocrdma device.
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As part of SRQ receive buffers posting we populate a non-zero tag
which will be returned in SRQ receive completions.
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Increment the ABI version count for driver/library interface.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
While loading RoCE driver be2net driver should check for ABI version
to catch functional incompatibilities.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow creating DPP QP even if inline-data is not requested. This is an
optimization to lower latency.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
ocrdma driver selects execution path based on sli_family and asic
generation number. This introduces code to read the asic gen number
from pci register instead of obtaining it from the Emulex NIC driver.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Stale entries in the CQ being destroyed causes hardware to generate
EQEs indefinitely for a given CQ. Thus causing uncontrolled execution
of irq_handler. This patch fixes this using following sementics:
* irq_handler will ring EQ doorbell atleast once and implement budgeting scheme.
* cq_destroy will count number of valid entires during destroy and ring
cq-db so that hardware does not generate uncontrolled EQE.
* cq_destroy will synchronize with last running irq_handler instance.
* arm_cq will always defer arming CQ till poll_cq, except for the first arm_cq call.
* poll_cq will always ring cq-db with arm=SET if arm_cq was called prior to enter poll_cq.
* poll_cq will always ring cq-db with arm=UNSET if arm_cq was not called prior to enter poll_cq.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Current hardware doesn't correctly support DSGL.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
To avoid racing with other threads doing close/flush/whatever, rx_data()
should hold the endpoint mutex.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a race between ULP threads doing an accept/reject, and the
ingress processing thread handling close/abort for the same connection.
The accept/reject path needs to hold the lock to serialize these paths.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
[ Fold in locking fix found by Dan Carpenter <dan.carpenter@oracle.com>.
- Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
These methods appear to only mimic the sg_dma_address() and
sg_dma_len() behavior.
They can be safely removed.
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The removal of these methods is compensated for by code changes to
.map_sg to insure that the vanilla sg_dma_address() and sg_dma_len()
will do the same thing as the equivalent former ib_sg_dma_address()
and ib_sg_dma_len() calls into the drivers.
The introduction of this patch required that the struct
ipath_dma_mapping_ops be converted to a C99 initializer.
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove the overload for .dma_len and .dma_address
The removal of these methods is compensated for by code changes to
.map_sg to insure that the vanilla sg_dma_address() and sg_dma_len()
will do the same thing as the equivalent former ib_sg_dma_address()
and ib_sg_dma_len() calls into the drivers.
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Tested-by: Vinod Kumar <vinod.kumar@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
My static checker complains that the sprintf() here can overflow.
drivers/infiniband/hw/mlx4/main.c:1836 mlx4_ib_alloc_eqs()
error: format string overflow. buf_size: 32 length: 69
This seems like a valid complaint. The "dev->pdev->bus->name" string
can be 48 characters long. I just made the buffer 80 characters instead
of 69 and I changed the sprintf() to snprintf().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The code was indented too far and also kernel style says we should have
curly braces.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case of error when writing to userspace, function ehca_create_cq()
does not set an error code before following its error path.
This patch sets the error code to -EFAULT when ib_copy_to_udata()
fails.
This was caught when using spatch (aka. coccinelle)
to rewrite call to ib_copy_{from,to}_udata().
Link: 75ebf2c103:ib_copy_udata.cocci
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case of error when writing to userspace, the function mthca_create_cq()
does not set an error code before following its error path.
This patch sets the error code to -EFAULT when ib_copy_to_udata() fails.
This was caught when using spatch (aka. coccinelle)
to rewrite call to ib_copy_{from,to}_udata().
Link: 75ebf2c103:ib_copy_udata.cocci
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If kmalloc() fails in c4iw_alloc_ucontext(), the function
leaves but does not set an error code in ret variable:
it will return 0 to the caller.
This patch set ret to -ENOMEM in such case.
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Steve Wise <swise@chelsio.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code which is dealing with SRIOV alias GUIDs in the mlx4 IB driver has some
logic which operated according to the maximal possible active functions (PF + VFs).
After the single port VFs code integration this resulted in a flow of false-positive
warnings going to the kernel log after the PF driver started the alias GUID work.
Fix it by referring to the actual number of functions.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing an MPA Start Request, if the listening endpoint is
DEAD, then abort the connection.
If the IWCM returns an error, then we must abort the connection and
release resources. Also abort_connection() should not post a CLOSE
event, so clean that up too.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These are generated by HW in some error cases and need to be
silently discarded.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If cxgb4_ofld_send() returns < 0, then send_fw_pass_open_req() must
free the request skb and the saved skb with the tcp header.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
In wrapped commands, we need to verify and convert
the slave's port into the real physical port.
Furthermore, when sending the response back to the slave,
a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
The slave assumes that sqpn is used for QP1 communication.
If the slave is assigned to a port != (first port), we need
to adjust the sqpn that will direct its QP1 packets into the
correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
In B0 steering, gid[5] contains the port. It needs
to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
When a slave queries the hardware, it needs to view only
the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
The QP port is encoded in the sched_qp, thus in modify_qp we need
to encode the correct port in sched_qp.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some code in the mlx4 IB driver stack assumed MLX4_MAX_PORTS ports.
Instead, we should only loop until the number of actual ports in i
the device, which is stored in dev->caps.num_ports.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning directly is easier to read than do-nothing gotos. Remove the
duplicative check on "olp" and pull the code in one indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Improve performance by changing the behavour of the driver when all
SDMA descriptors are in use, and the processes adding new descriptors
are single- or multi-rail.
For single-rail processes, the driver will block the call and finish
posting all SDMA descriptors onto the hardware queue before returning
back to PSM. Repeated kernel calls are slower than blocking.
For multi-rail processes, the driver will return to PSM as quick as
possible so PSM can feed packets to other rail. If all hardware
queues are full, PSM will buffer the remaining SDMA descriptors until
notified by interrupt that space is available.
This patch builds a red-black tree to track the number rails opened by
a particular PID. If the number is more than one, it is a multi-rail
PSM process, otherwise, it is a single-rail process.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: John A Gregor <john.a.gregor@intel.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: CQ Tang <cq.tang@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We cannot save the mapped length using the rdma max_page_list_len field
of the ib_fast_reg_page_list struct because the core code uses it. This
results in an incorrect unmap of the page list in c4iw_free_fastreg_pbl().
I found this with dma mapping debugging enabled in the kernel. The
fix is to save the length in the c4iw_fr_page_list struct.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Based on original work from Jay Hernandez <jay@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Always release the neigh entry in rx_pkt().
Based on original work by Santosh Rastapur <santosh@chelsio.com>.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
find_route() must treat loopback as a valid egress interface.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a four byte hole at the end of the "uresp" struct after the
->qid_mask member.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
These sizes should be unsigned so we don't allow negative values and
have underflow bugs. These can come from the user so there may be
security implications, but I have not tested this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix the following warning for the mlx4 driver:
$ make M=drivers/infiniband C=2 CF=-D__CHECK_ENDIAN__
drivers/infiniband/hw/mlx4/qp.c:1885:31: warning: restricted __be16 degrades to integer
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
drivers/infiniband/hw/ocrdma/ocrdma_verbs.c: In function ‘_ocrdma_modify_qp’:
drivers/infiniband/hw/ocrdma/ocrdma_verbs.c:1299:31: error: ‘old_qps’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
status = ocrdma_mbx_modify_qp(dev, qp, attr, attr_mask, old_qps);
ocrdma_mbx_modify_qp() (and subsequent calls) doesn't appear to use old_qps
so it doesn't need to be passed on. Removing the variable results in the
warning going away.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Devesh Sharma (Devesh.sharma@emulex.com)
Signed-off-by: Roland Dreier <roland@purestorage.com>
We don't need to test "ret" twice and also the white space is messed up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We already know "pusable" is non-zero, no need to check again.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
%pa format already prints in hexadecimal format, so remove the '0x' annotation
to avoid a double '0x0x' pattern.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case of error while accessing to userspace memory, function
nes_create_qp() returns NULL instead of an error code wrapped through
ERR_PTR(). But NULL is not expected by ib_uverbs_create_qp(), as it
check for error with IS_ERR().
As page 0 is likely not mapped, it is going to trigger an Oops when
the kernel will try to dereference NULL pointer to access to struct
ib_qp's fields.
In some rare cases, page 0 could be mapped by userspace, which could
turn this bug to a vulnerability that could be exploited: the function
pointers in struct ib_device will be under userspace total control.
This was caught when using spatch (aka. coccinelle)
to rewrite calls to ib_copy_{from,to}_udata().
Link: https://www.gitorious.org/opteya/ib-hw-nes-create-qp-null
Link: 75ebf2c103:ib_copy_udata.cocci
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In qib_create_ctxts() we allocate an array to hold recv contexts. Then attempt
to create data for those recv contexts. If that call to qib_create_ctxtdata()
fails then an error is returned but the previously allocated memory is not
freed.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit af061a644a add some code in qib_ib_rcv() which
trigger a warning from coccicheck (coccinelle/spatch):
$ make C=2 CHECK=scripts/coccicheck drivers/infiniband/hw/qib/
CHECK drivers/infiniband/hw/qib/qib_verbs.c
drivers/infiniband/hw/qib/qib_verbs.c:679:5-32: code aligned with following code on line 681
CC [M] drivers/infiniband/hw/qib/qib_verbs.o
In fact, according to similar code in qib_kreceive(),
qib_ib_rcv() code is correct but improperly indented.
This patch fix indentation for the misaligned portion.
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: infinipath@intel.com
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: cocci@systeme.lip6.fr
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit c804f07248 moved qib_assign_ctxt() to
do_qib_user_sdma_queue_create() but dropped the braces
around the statements.
This was spotted by coccicheck (coccinelle/spatch):
$ make C=2 CHECK=scripts/coccicheck drivers/infiniband/hw/qib/
CHECK drivers/infiniband/hw/qib/qib_file_ops.c
drivers/infiniband/hw/qib/qib_file_ops.c:1583:2-23: code aligned with following code on line 1587
This patch adds braces back.
Link: http://marc.info/?i=cover.1394485254.git.ydroneaud@opteya.com
Cc: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: infinipath@intel.com
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: cocci@systeme.lip6.fr
Cc: stable@vger.kernel.org
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The counters, unicast_xmit, unicast_rcv, multicast_xmit, multicast_rcv
are now maintained as percpu variables.
The mad code is modified to add a z_ latch so that the percpu counters
monotonically increase with appropriate adjustments in the reset,
read logic to maintain the z_ latch.
This patch also corrects the fact the unitcast_xmit wasn't handled
at all for UC and RC QPs.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch replaces the dd->int_counter with a percpu counter.
The maintanance of qib_stats.sps_ints and int_counter are
combined into the new counter.
There are two new functions added to read the counter:
- qib_int_counter (for a particular qib_devdata)
- qib_sps_ints (for all HCAs)
A z_int_counter is added to allow the interrupt detection logic
to determine if interrupts have occured since z_int_counter
was "reset".
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The debugfs init code was incorrectly called before the idr mechanism
is used to get the unit number, so the dd->unit hasn't been
initialized. This caused the unit relative directory creation to fail
after the first.
This patch moves the init for the debugfs stuff until after all of the
failures and after the unit number has been determined.
A bug in unwind code in qib_alloc_devdata() is also fixed.
Cc: <stable@vger.kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Guard against a potential buffer overrun. The size to read from the
user is passed in, and due to the padding that needs to be taken into
account, as well as the place holder for the ICRC it is possible to
overflow the 32bit value which would cause more data to be copied from
user space than is allocated in the buffer.
Cc: <stable@vger.kernel.org>
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Guard against a potential buffer overrun. Right now the qib driver is
protected by the fact that the data structure in question is only 16
bits. Should that ever change the problem will be exposed. There is a
similar defect in the ipath driver and this brings the two code paths
into sync.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fixes to enable the negotiation of the supported IRD/ORD sizes with
the peer when exchanging MPA v2 messages in connection establishment.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current logic suffers from a slow response time to disable user DB
usage, and also fails to avoid DB FIFO drops under heavy load. This commit
fixes these deficiencies and makes the avoidance logic more optimal.
This is done by more efficiently notifying the ULDs of potential DB
problems, and implements a smoother flow control algorithm in iw_cxgb4,
which is the ULD that puts the most load on the DB fifo.
Design:
cxgb4:
Direct ULD callback from the DB FULL/DROP interrupt handler. This allows
the ULD to stop doing user DB writes as quickly as possible.
While user DB usage is disabled, the LLD will accumulate DB write events
for its queues. Then once DB usage is reenabled, a single DB write is
done for each queue with its accumulated write count. This reduces the
load put on the DB fifo when reenabling.
iw_cxgb4:
Instead of marking each qp to indicate DB writes are disabled, we create
a device-global status page that each user process maps. This allows
iw_cxgb4 to only set this single bit to disable all DB writes for all
user QPs vs traversing the idr of all the active QPs. If the libcxgb4
doesn't support this, then we fall back to the old approach of marking
each QP. Thus we allow the new driver to work with an older libcxgb4.
When the LLD upcalls iw_cxgb4 indicating DB FULL, we disable all DB writes
via the status page and transition the DB state to STOPPED. As user
processes see that DB writes are disabled, they call into iw_cxgb4
to submit their DB write events. Since the DB state is in STOPPED,
the QP trying to write gets enqueued on a new DB "flow control" list.
As subsequent DB writes are submitted for this flow controlled QP, the
amount of writes are accumulated for each QP on the flow control list.
So all the user QPs that are actively ringing the DB get put on this
list and the number of writes they request are accumulated.
When the LLD upcalls iw_cxgb4 indicating DB EMPTY, which is in a workq
context, we change the DB state to FLOW_CONTROL, and begin resuming all
the QPs that are on the flow control list. This logic runs on until
the flow control list is empty or we exit FLOW_CONTROL mode (due to
a DB DROP upcall, for example). QPs are removed from this list, and
their accumulated DB write counts written to the DB FIFO. Sets of QPs,
called chunks in the code, are removed at one time. The chunk size is 64.
So 64 QPs are resumed at a time, and before the next chunk is resumed, the
logic waits (blocks) for the DB FIFO to drain. This prevents resuming to
quickly and overflowing the FIFO. Once the flow control list is empty,
the db state transitions back to NORMAL and user QPs are again allowed
to write directly to the user DB register.
The algorithm is designed such that if the DB write load is high enough,
then all the DB writes get submitted by the kernel using this flow
controlled approach to avoid DB drops. As the load lightens though, we
resume to normal DB writes directly by user applications.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Anand Priyadarshee <anandp@chelsio.com>.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To activate RoCE/SRIOV, need to remove the following:
1. In mlx4_ib_add, need to remove the error return preventing
initialization of a RoCE port under SRIOV.
2. In update_vport_qp_params (in resource_tracker.c) need to remove
the error return when a RoCE RC or UD qp is detected.
This error return causes the INIT-to-RTR qp transition to fail
in the wrapper function under RoCE/SRIOV.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Handle CM_SIDR_REQ_ATTR_ID and CM_SIDR_REP_ATTR_ID
in multiplex_cm_handler and demux_cm_handler.
* Handle Service ID Resolution messages and REQ messages
separately, for their formats are different.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,
This is achieved as follows:
Outgoing MADs:
1. Source MAC: obtained from the CQ completion structure
(struct ib_wc, smac field).
2. Destination MAC: obtained from the tunnel header
3. vlan_id: obtained from the tunnel header.
Incoming MADs
1. The source (i.e., remote) MAC and vlan_id are passed in
the tunnel header to the proxy QP1.
VST mode support:
For outgoing MADs, the vlan_id obtained from the header is
discarded, and the vlan_id specified by the Hypervisor is used
instead.
For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
"invalid" vlan (0xffff) is substituted when forwarding to the slave.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IB side of RoCE requires the MAC table index of the
MAC address used by its QPs.
To obtain the real MAC index, the IB side registers the
MAC (increasing its ref count, and also returning the
real MAC index) during the modify-qp sequence.
This protects against the ETH side deleting or modifying
that MAC table entry while the QP is active.
Note that until the modify-qp command returns success,
the MAC and VLAN information only has "candidate" status.
If the modify-qp succeeds, the "candidate" info is promoted
to the operational MAC/VLAN info for the qp. If the modify fails,
the candidate MAC/VLAN is unregistered, and the old qp info
is preserved.
The patch is a bit complex, because there are multiple qp
transitions where the primary-path information may be
modified: INIT-to-RTR, and SQD-to-SQD.
Similarly for the alternate path information.
Therefore the code must handle cases where path information
has already been entered into the QP context by previous
qp transitions.
For the MAC address, the success logic is as follows:
1. If there was no previous MAC, simply move the candidate
MAC information to the operational information, and reset
the candidate MAC info.
2. If there was a previous MAC, unregister it. Then move
the MAC information from candidate to operational, and
reset the candidate info (as in 1. above).
The MAC address failure logic is the same for all cases:
- Unregister the candidate MAC, and reset the candidate MAC info.
For Vlan registration, the logic is similar.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs: Remaining GIDS are divided evenly between VFs activated by the driver.
If the division is not even, lower-numbered VFs get an extra GID.
For an IB interface, the number of gids per guest remains as before: one gid per guest.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.
This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently support only T10-DIF types of signature handover operations
(types 1|2|3).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This commit takes care of the generated signature error CQE generated
by the HW (if happened). The underlying mlx5 driver will handle
signature error completions and will mark the relevant memory region
as dirty.
Once the consumer gets the completion for the transaction, it must
check for signature errors on signature memory region using a new
lightweight verb ib_check_mr_status().
In case the user doesn't check for signature error (i.e. doesn't call
ib_check_mr_status() with status check IB_MR_CHECK_SIG_STATUS), the
memory region cannot be used for another signature operation
(REG_SIG_MR work request will fail).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch implements IB_WR_REG_SIG_MR posted by the user.
Baisically this WR involves 3 WQEs in order to prepare and properly
register the signature layout:
1. post UMR WR to register the sig_mr in one of two possible ways:
* In case the user registered a single MR for data so the UMR data segment
consists of:
- single klm (data MR) passed by the user
- BSF with signature attributes requested by the user.
* In case the user registered 2 MRs, one for data and one for protection,
the UMR consists of:
- strided block format which includes data and protection MRs and
their repetitive block format.
- BSF with signature attributes requested by the user.
2. post SET_PSV in order to set the memory domain initial
signature parameters passed by the user.
SET_PSV is not signaled and solicited CQE.
3. post SET_PSV in order to set the wire domain initial
signature parameters passed by the user.
SET_PSV is not signaled and solicited CQE.
* After this compound WR we place a small fence for next WR to come.
This patch also introduces some helper functions to set the BSF correctly
and determining the signature format selectors.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
get_umr_flags helper function might be used for types of access modes
other than ACCESS_MODE_MTT, such as ACCESS_MODE_KLM. So remove it from
helper, and callers will add their own access mode flag.
This commit does not add/change functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As a preliminary step for signature feature which will require posting
multiple (3) WQEs for a single WR, we break post_send routine WQE
indexing into begin and finish routines.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If user requested signature enable we initialize relevant mlx5_ib_qp
members. We mark the qp as sig_enable and we increase the effective
SQ size, but still limit the user max_send_wr to original size
computed. We also allow the create_qp routine to accept sig_enable
create flag.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Support create_mr and destroy_mr verbs. Creating ib_mr may be done
for either ib_mr that will register regular page lists like
alloc_fast_reg_mr routine, or indirect ib_mrs that can register other
(pre-registered) ib_mrs in an indirect manner.
In addition user may request signature enable, that will mean that the
created ib_mr may be attached with signature attributes (BSF, PSVs).
Currently we only allow direct/indirect registration modes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch refactors the IB core umem code and vendor drivers to use a
linear (chained) SG table instead of chunk list. With this change the
relevant code becomes clearer—no need for nested loops to build and
use umem.
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We should use rdma_vlan_dev_real_dev() instead of using vlan_dev_real_dev()
when building the GID table for a vlan interface.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use correct value for obtaining traffic class from device
response for Query QP request.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Error reported at http://marc.info/?l=linux-rdma&m=138995755801039&w=2
Fix short to int cast for big endian systems.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove Kconfig dependency of mlx5_ib/mlx5_core on X86, since there is
no such dependency in reality.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Research has shown that commit a77fcf8950 ("IB/qib: Use a single
txselect module parameter for serdes tuning") missed a key serdes init
sequence.
This patch add that sequence.
Cc: <stable@vger.kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For userspace RoCE UD QPs we need to know the GID format that the
kernel uses, e.g when working over older kernels. For that end, add a
new port capability IB_PORT_IP_BASED_GIDS and report it when query
port is issued.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When scanning netdevices we need to check a few more conditions and
cases to build the IBoE GID table properly. For example, under
bonding we must make sure that when a port is down, the bond IP
address isn't programmed as a GID, since doing so will cause failure
with IB core flows that selects ports by GID.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The IBoE code used to reset the GID table did it for all Ethernet
ports of the device. Since the whole architecture of generating GIDs
and responding to events is port-based, this is inefficient and can
lead to wrong content in the GID table. Change the reset flow to be
per-port.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Updating the GID table under IBoE requires read/write from/to shared
data structures. These data structures are protected with the device
iboe lock. The flows that modify the GID table start from
1. Initializing the GID table
2. NETDEV events
3. INET or INET6 events
This patch makes sure that the flow of initializing the GID table is
consistent with the other two flows w.r.t on what step the lock is taken.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
On the one hand, the invocation of netdev_master_upper_dev_get()
within mlx4_ib_scan_netdevs() must be done with rtnl lock held. On
the other hand, it's wrong to call rtnl_lock() from within this
function since it's also called by our netdev notifier callback.
Therefore move the locking to mlx4_ib_add() so that both cases are
covered.
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Make sure that for Ethernet ports, the port GID table index 0 is always
occupied with a default GID of the relevant IPv6 link-local adderss.
This provides better user experience for legacy applications that don't use
the RDMA CM and were working on index 0 prior to the IP addressing change.
Also, as GIDs are generated from IP addresses of the network devices that
are associated with the port, it's basically possible that the GID table
will be empty if no IP address was assigned. This doesn't comply with the
IB spec section 4.1.1 "GID usage and properties".
Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When the device has only Ethernet ports, don't try to allocate range
of steerable UD QPs since they aren't needed. This fixes an issue
where mlx4 VFs tried to allocate a range of UD steerable QPs, but
failed to do so.
Fixes: c1c9850112 ("IB/mlx4: Add support for steerable IB UD QPs")
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently Connect-IB does not support blocking multicast loopback, so
don't set IB_DEVICE_BLOCK_MULTICAST_LOOPBACK in the device caps.
Reported by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit c1be5232d2 ("Fix micro UAR allocator") broke binary compatibility
between libmlx5 and mlx5_ib since it defines a different value to the number
of micro UARs per page, leading to wrong calculation in libmlx5. This patch
defines struct mlx5_ib_alloc_ucontext_req_v2 as an extension to struct
mlx5_ib_alloc_ucontext_req. The extended size is determined in mlx5_ib_alloc_ucontext()
and in case of old library we use uuarn 0 which works fine -- this is
acheived due to create_user_qp() falling back from high to medium then to
low class where low class will return 0. For new libraries we use the
more sophisticated allocation algorithm.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix the RC QPs send queue overhead computation to take into account
two additional segments in the WQE which are needed for registration
operations.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Verify that reserved fields in struct mlx5_ib_resize_cq are cleared
before continuing execution of the verb. This is required to allow
making use of this area in future revisions.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current code attmepts to call ib_umem_get() even if the length is
zero, which causes a failure. Since the spec allows zero length work
queues, change the code so we don't call ib_umem_get() in those cases.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Implement resize CQ which is a mandatory verb in mlx5.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Modify CQ is used by ULPs like IPoIB to change moderation parameters. This
patch adds support in mlx5.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Put a wmb() to make sure the doorbell record is visible to the HCA before we
hit doorbell.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use the possibly more efficient ether_addr_equal() instead of memcmp().
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The GSI QP type is compatible with and should be allowed to send data
to/from any UD QP. This was found when testing ibacm on the same node
as an SA.
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Building mem.o for 32 bits x86 triggers a GCC warning:
drivers/infiniband/hw/cxgb4/mem.c: In function '_c4iw_write_mem_dma_aligned':
drivers/infiniband/hw/cxgb4/mem.c:79:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Silence that warning by casting "&wr_wait" to unsigned long before
casting it to __be64. That's what _c4iw_write_mem_inline() already does.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a path in handle_vq() where kmem_cache_free() can be called
with pointer to a local variable. It can happen if vq_repbuf_alloc()
failed to allocate memory from cache and req is NULL.
The patch adds check if cache memory was allocated before freeing it.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Svetlana Mavrina <another.karnil@gmail.com>
Reviewed-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This is called from qp_grp_and_vf_bind() and we are holding the
vf->lock so the allocation can't sleep.
Fixes: e3cf00d0a8 ('IB/usnic: Add Cisco VIC low-level hardware driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Now that ocrdma supports IP-based addressing, we need to depend on
INET, since ocrdma registers itself for net device events.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Since mlx4_ib supports IP based addressing, a dependency on INET needs
to be added, since mlx4_ib registers itself for net device events.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch is similar in spirit to the "IB/mlx4: Use IBoE (RoCE) IP
based GIDs in the port GID table" patch.
Changes to inet4 and inet6 addresses for the host are monitored and if
the address is associated with an ocrdma device then a gid is added or
deleted from the device's gid table. The gid format will be a IPv4 to
IPv6 mapped or the IPv6 address.
Cc: Naresh Gottumukkala <bgottumukkala@emulex.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch is similar in spirit to the "IB/mlx4: Handle Ethernet L2
parameters for IP based GID addressing". It handles the fact that IP
based RoCE gids don't store Ethernet L2 parameters, MAC and VLAN.
When building an address handle, instead of parsing the dgid to
get the MAC and VLAN, take them from the address handle attributes.
Cc: Naresh Gottumukkala <bgottumukkala@emulex.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
IP based RoCE gids don't store Ethernet L2 parameters, MAC and VLAN.
Therefore, we need to extract them from the CQE and place them in
struct ib_wc (to be used for cases were they were taken from the gid).
Also, when modifying a QP or building address handle, instead of
parsing the dgid to get the MAC and VLAN, take them from the address
handle attributes.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Currently, the mlx4 driver set IBoE (RoCE) gids to encode related
Ethernet netdevice interface MAC address and possibly VLAN id.
Change this scheme such that gids encode interface IP addresses (both
IP4 and IPv6).
This requires learning the IP addresses which are of use by a
netdevice associated with the HCA port, formatting them to gids and
adding them to the port gid table. Furthermore, events of add and
delete address are caught to maintain the gid table accordingly.
Associated IP addresses may belong to a master of an Ethernet
netdevice on top of that port so this should be considered when
building and maintaining the gid table.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The variable qp_grp is initialized but never used otherwise, so remove
the unused variable.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Roland Dreier <roland@purestorage.com>
usNIC userspace/kernel ABI should be set to 4 instead of 3.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
usNIC default transport is UDP. Hence, advertise RDMA_NODE_USNIC_UDP
by default for usNIC devices.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
usNIC needs inet notifiers to function correctly, so add a Kconfig
dependency on CONFIG_INET.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch add the support for Ethernet L2 attributes in the
verbs/cm/cma structures.
When dealing with L2 Ethernet, we should use smac, dmac, vlan ID and priority
in a similar manner that the IB L2 (and the L4 PKEY) attributes are used.
Thus, those attributes were added to the following structures:
* ib_ah_attr - added dmac
* ib_qp_attr - added smac and vlan_id, (sl remains vlan priority)
* ib_wc - added smac, vlan_id
* ib_sa_path_rec - added smac, dmac, vlan_id
* cm_av - added smac and vlan_id
For the path record structure, extra care was taken to avoid the new
fields when packing it into wire format, so we don't break the IB CM
and SA wire protocol.
On the active side, the CM fills. its internal structures from the
path provided by the ULP. We add there taking the ETH L2 attributes
and placing them into the CM Address Handle (struct cm_av).
On the passive side, the CM fills its internal structures from the WC
associated with the REQ message. We add there taking the ETH L2
attributes from the WC.
When the HW driver provides the required ETH L2 attributes in the WC,
they set the IB_WC_WITH_SMAC and IB_WC_WITH_VLAN flags. The IB core
code checks for the presence of these flags, and in their absence does
address resolution from the ib_init_ah_from_wc() helper function.
ib_modify_qp_is_ok is also updated to consider the link layer. Some
parameters are mandatory for Ethernet link layer, while they are
irrelevant for IB. Vendor drivers are modified to support the new
function signature.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds support for steerable (NETIF) QP creation. When we
create the device, we allocate a range of steerable QPs.
Afterward when a QP is created with the NETIF flag, it's allocated
from this range. Allocation is managed by bitmap allocator.
Internal steering rules for those QPs is automatically generated on
their creation.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The mlx4 device requires adding IB flow spec to rules that apply over
infiniband link layer. This patch adds a mechanism to add such a rule.
If higher levels e.g. IP/UDP/TCP flow specs are provided, the device
requires us to add an empty wild-carded IB rule. Furthermore, the device
requires the QPN to be put in the rule.
Add here specific parsing support for IB empty rules and the ability
to self-generate missing specs based on existing ones.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Up until now, flow steering wasn't supported when using IB ports.
This patch enables support for flow steering if all hardware ports
support that, for example the new MLX4_DEV_CAP_FLAG2_DMFS_IPOIB mlx4
device capability.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The micro UAR (uuar) allocator had a bug which resulted from the fact
that in each UAR we only have two micro UARs avaialable, those at
index 0 and 1. This patch defines iterators to aid in traversing the
list of available micro UARs when allocating a uuar.
In addition, change the logic in create_user_qp() so that if high
class allocation fails (high class means lower latency), we revert to
medium class and not to the low class.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The variable start in struct mlx5_ib_mr is never used. Remove it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add comment describing usnic_transport_rsrv port and remove
extraneous space from usnic_transport.c.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Roland Dreier