There is one design rule according to SAI's reference manual:
If the transmitter bit clock and frame sync are to be used by both transmitter
and receiver, the transmitter must be configured for asynchronous operation
and the receiver for synchronous operation.
And SYNC of TCR2 is a 2-width control bit:
00 Asynchronous mode.
01 Synchronous with receiver.
10 Synchronous with another SAI transmitter.
11 Synchronous with another SAI receiver.
So the driver should have set SYNC bit of TCR2 to 0x0, and meanwhile set SYNC
bit of RCR2 to 0x1 (Synchronous with transmitter).
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This adds an initial machine driver for the ES8328 audio codec on Freescale
boards. The driver supports headphones and an audio regulator for an onboard
speaker amp.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The previous patch (ASoC: fsl_sai: Add asynchronous mode support) added
new Device Tree bindings for Asynchronous and Synchronous modes support.
However, these two shall not be present at the same time.
So this patch just simply makes them exclusive so as to avoid incorrect
Device Tree binding usage.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SAI supports these operation modes:
1) asynchronous mode
Both Tx and Rx are set to be asynchronous.
2) synchronous mode (Rx sync with Tx)
Tx is set to be asynchronous, Rx is set to be synchronous.
3) synchronous mode (Tx sync with Rx)
Rx is set to be asynchronous, Tx is set to be synchronous.
4) synchronous mode (Tx/Rx sync with another SAI's Tx)
5) synchronous mode (Tx/Rx sync with another SAI's Rx)
* 4) and 5) are beyond this patch because they are related with another SAI.
As the initial version of this SAI driver, it supported 2) as default while
the others were totally missing.
So this patch just adds supports for 1) and 3).
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is one design rule according to SAI's reference manual:
If the transmitter bit clock and frame sync are to be used by both transmitter
and receiver, the transmitter must be configured for asynchronous operation
and the receiver for synchronous operation.
And SYNC of TCR2 is a 2-width control bit:
00 Asynchronous mode.
01 Synchronous with receiver.
10 Synchronous with another SAI transmitter.
11 Synchronous with another SAI receiver.
So the driver should have set SYNC bit of TCR2 to 0x0, and meanwhile set SYNC
bit of RCR2 to 0x1 (Synchronous with transmitter).
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds software reset code in dai_probe() so as to make a true init
by clearing SAI's internal logic, including the bit clock generation, status
flags, and FIFO pointers.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Original driver didn't store the number of slots, just fix the slot number
to 2, use this default number to calculate bclk and pins for TX/RX.
In this patch, add one parameter for slots, and update the calculation of
bclk and pins of TX/RX. Then driver will be compatible with slots > 2 in
TDM mode.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Freescale Generic ASoC Sound Card is a general ASoC DAI Link driver that
can be used, ideally, for all Freescale CPU DAI drivers and external CODECs.
The idea of this generic sound card is a bit like ASoC Simple Card. However,
for Freescale SoCs (especially those released in recent years), most of them
have ASRC (Documentation/devicetree/bindings/sound/fsl,asrc.txt) inside. And
this is a specific feature that might be painstakingly controlled and merged
into the Simple Card driver.
So having this driver will allow all Freescale SoC users to benefit from the
simplification to support a new card and the capability of wide sample rates
support through ASRC.
The driver is initially designed for sound card using I2S or PCM DAI formats.
However, it's also possible to merge those non-I2S/PCM type sound cards, such
as S/PDIF audio and HDMI audio, into this card as long as the merge will not
break the original function and as long as there is something redundant that
can be abstracted along with I2S type sound cards.
As an initial version, it only supports three cards that I can test:
imx-audio-cs42888, a new card that links ESAI with CS42888 CODEC
imx-audio-sgtl5000, just like the old imx-sgtl5000.c driver
imx-audio-wm8962, just like the old imx-wm8962.c driver
The driver is also compatible with the old Device Tree bindings of WM8962 and
SGTL5000. So we may consider to remove those two drivers after this driver is
totally enabled. (It needs to be added into defconfig)
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Original driver didn't store the number of slots, just fix the slot number
to 2, use this default number to calculate bclk and pins for TX/RX.
In this patch, add one parameter for slots, and update the calculation of
bclk and pins of TX/RX. Then driver will be compatible with slots > 2 in
TDM mode.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit a603c8ee52.
fsl_asoc_xlate_tdm_slot_mask() is different with snd_soc_xlate_tdm_slot_mask().
fsl_asoc_xlate_tdm_slot_mask() will set the enabled bit to 0, disabled bit
to 1. snd_soc_xlate_tdm_slot_mask() will set the enabled bit to 1, disabled
bit to 0.
For esai when the bit value is 1, the slot is enabled, when the bit value is 0,
the slot is disabled. If using fsl_asoc_xlate_tdm_slot_mask(), the esai will
work abnormally. So revert this patch, make the esai use default function.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add SND_SOC_DAIFMT_CBM_CFS support for Freescale architecture.
Successfully tested on i.MX 6Quad Wandboard and UDOO boards connected to
the pcm1792a codec.
In CBM_CFS mode, when using a sample size of 16 bits, we cannot use
CCSR_SSI_SCR_I2S_MODE_MASTER since we get a frame sync every 16 bits.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Fabio Falzoi <fabio.falzoi84@gmail.com>
Tested-by: Angelo Adamo <adamo.a60@gmail.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since we pass the port number through file private data for debugfs we cast
it to and from a pointer so use uintptr_t in order to ensure that the
types are compatible, avoiding warnings on 64 bit platforms where pointers
are 64 bit and unsigned integers 32 bit.
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch 3117bb3109dc: "ASoC: fsl_asrc: Add ASRC ASoC CPU DAI and
platform drivers" from Jul 29, 2014, leads to the following Smatch
complaint:
sound/soc/fsl/fsl_asrc_dma.c:304 fsl_asrc_dma_shutdown()
warn: variable dereferenced before check 'pair' (see line 302)
sound/soc/fsl/fsl_asrc_dma.c
301 struct fsl_asrc_pair *pair = runtime->private_data;
302 struct fsl_asrc *asrc_priv = pair->asrc_priv;
^^^^^^^^^^^^^^^
Dereference.
303
304 if (pair && asrc_priv->pair[pair->index] == pair)
^^^^
Check.
305 asrc_priv->pair[pair->index] = NULL;
306
So we just let the driver check pair before using it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DPCM needs extra dapm routes in the machine driver to route audio
between Front-End and Back-End. In order to differ the stream names
in the route map from CODECs, we here add specific stream names to
SSI driver so that we can implement ASRC via DPCM to it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
DPCM needs extra dapm routes in the machine driver to route audio
between Front-End and Back-End. In order to differ the stream names
in the route map from CODECs, we here add specific stream names to
SPDIF driver so that we can implement ASRC via DPCM to it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DPCM needs extra dapm routes in the machine driver to route audio
between Front-End and Back-End. In order to differ the stream names
in the route map from CODECs, we here add specific stream names to
SAI driver so that we can implement ASRC via DPCM to it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DPCM needs extra dapm routes in the machine driver to route audio
between Front-End and Back-End. In order to differ the stream names
in the route map from CODECs, we here add specific stream names to
ESAI driver so that we can implement ASRC via DPCM to it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a cut and paste bug so it returns success instead of the error
code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Building a kernel with SND_SOC_GENERIC_DMAENGINE_PCM=n leads to the following
error:
ERROR: "snd_dmaengine_pcm_prepare_slave_config" [sound/soc/fsl/snd-soc-fsl-asrc.ko] undefined!
Let SND_SOC_FSL_ASRC select SND_SOC_GENERIC_DMAENGINE_PCM in order to fix such
error.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following build errors that were observed by building with
make ARCH=microblaze allyesconfig:
>> sound/soc/fsl/fsl_asrc.c:906:5: warning: "CONFIG_PM_RUNTIME" is not defined [-Wundef]
#if CONFIG_PM_RUNTIME
^
>> sound/soc/fsl/fsl_asrc.c:934:5: warning: "CONFIG_PM_SLEEP" is not defined [-Wundef]
#if CONFIG_PM_SLEEP
^
>> sound/soc/fsl/fsl_asrc.c:906:5: warning: "CONFIG_PM_RUNTIME" is not defined [-Wundef]
#if CONFIG_PM_RUNTIME
^
>> sound/soc/fsl/fsl_asrc.c:934:5: warning: "CONFIG_PM_SLEEP" is not defined [-Wundef]
#if CONFIG_PM_SLEEP
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Asynchronous Sample Rate Converter (ASRC) converts the sampling rate of a
signal associated with an input clock into a signal associated with a different
output clock. The driver currently works as a Front End of DPCM with other Back
Ends DAI links such as ESAI<->CS42888 and SSI<->WM8962 and SAI. It converts the
original sample rate to a common rate supported by Back Ends for playback while
converts the common rate of Back Ends to a desired rate for capture. It has 3
pairs to support three different substreams within totally 10 channels.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The previous enable flow:
1, Enable TE&RE (SAI starts to consume tx FIFO and feed rx FIFO)
2, Mask IRQ of Tx/Rx to enable its interrupt.
3, Enable DMA request of Tx/Rx.
As this flow would enable DMA request later than TERE, the Tx FIFO
would be easily emptied into underrun while Rx FIFO would be easily
stuffed into overrun due to the delayed DMA transfering.
This issue happened merely occational before the patch 'ASoC: fsl_sai:
Reset FIFOs after disabling TE/RE' because there were useless data
remaining in the FIFO for the gap. However, it manifested after FIFO
reset's implemented.
After this patch, the new flow:
1, Enable DMA request of Tx/Rx.
2, Enable TE&RE (SAI starts to consume tx FIFO and feed rx FIFO)
3, Mask IRQ of Tx/Rx to enable its interrupt.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
TE/RE bit of T/RCSR will remain set untill the current frame is physically
finished. The FIFO reset operation should wait this bit's totally cleared
rather than ignoring its status which might cause TE/RE disabling failed.
This patch adds delay and timeout to wait for its completion before FIFO
reset.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For trigger start, we don't need to check if it's the first time to
enable TE/RE or second time. It doesn't hurt to enable them any way,
which in the meantime can reduce race condition for TE/RE enabling.
For trigger stop, we will definitely clear FRDE of current direction.
Thus the driver only needs to read the opposite one's.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Quite a few build coverage fixes in here among the usual small driver
fixes includling the sigmadsp change from Lars - moving the driver to
separate modules per bus (which is basically just code motion) avoids
issues with some combinations of buses being enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O7yF
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.16-rc1' into asoc-linus
ASoC: Fixes for v3.16
Quite a few build coverage fixes in here among the usual small driver
fixes includling the sigmadsp change from Lars - moving the driver to
separate modules per bus (which is basically just code motion) avoids
issues with some combinations of buses being enabled.
# gpg: Signature made Thu 19 Jun 2014 11:57:31 BST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
In the rx irq handling part, we should clear the flags in RCSR not TCSR.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SAI will not clear their FIFOs after disabling TE/RE. Therfore, the driver
should take care the task so as not to let useless data remain in the FIFO.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I received a report this morning from one of the Novena developers that
the behaviour of the iMX6 ASoC codec driver (using imx-pcm-dma.c) was
sub-optimal under high system load.
While there are issues relating to system load remaining, upon reviewing
the ASoC imx-pcm-dma.c driver, it was noticed that it not using the
residue support, because SDMA doesn't support it. This has the effect
that SDMA has to make multiple calls into the ASoC and ALSA code, one
for each period.
Since ALSA's snd_pcm_elapsed() does not need to be called multiple times
and it is entirely sufficient to call it once to update ALSA with the
current buffer position via the pointer method, we can do better here.
We can also avoid stopping the DMA entirely, just like real cyclic DMA
implementations behave. While this means that we replay some old samples,
this is a nicer behaviour than having audio stop and restart.
The changes to achieve this are relatively minor - imx-sdma.c can track
where the DMA is to the nearest descriptor boundary - it does this
already when deciding how many callbacks to issue. In doing this,
buf_tail always points at the descriptor which will complete next.
The residue is defined by the bytes remaining to the end of the buffer,
when the buffer is viewed as a single block of memory [start...end].
So, when we start out, there's a full buffer worth of residue, and this
counts down as we approach the end of the buffer, eventually becoming
zero at the end, before returning to the full buffer worth when we
wrap back to the start.
Moving the walking of the descriptors into the interrupt handler means
that we can update the BD_DONE flag at interrupt time, thus avoiding
a delayed tasklet stopping the cyclic DMA.
This means that the residue can be calculated from (total descriptors -
buf_tail) * descriptor size. This is what the change below does. We
update imx-pcm-dma.c to remove the NO_RESIDUE flag since we now provide
the residue.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 31ee2bfd72 ("ASoC: fsl: select SND_SOC_IMX_PCM_DMA
where needed") started selecting SND_SOC_IMX_PCM_DMA and
SND_SOC_IMX_PCM_FIQ for two drivers when building for i.MX.
This has turned out too aggressive, as FIQ is only available
for i.mx2 through i.mx5, but not i.mx6 or vybrid.
Further, two more drivers have become user-selectable in the
meantime, and they both depend on DMA for the imx platform
as well.
This changes the selection of FIQ to depend on the TZIC or
AVIC interrupt controllers that actually export the imx
specific FIQ interfaces, and adds the missing select statements
for SAI and ESAI.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
do_div() requires that the first parameter is a 64-bit integer,
which but clkrate was defined as an unsigned long. This caused
the following warnings:
CC sound/soc/fsl/fsl_ssi.o
sound/soc/fsl/fsl_ssi.c: In function 'fsl_ssi_set_bclk':
sound/soc/fsl/fsl_ssi.c:593:3: warning: comparison of distinct pointer types lacks a cast
sound/soc/fsl/fsl_ssi.c:593:3: warning: right shift count >= width of type
sound/soc/fsl/fsl_ssi.c:593:3: warning: passing argument 1 of '__div64_32' from incompatible pointer type
include/asm-generic/div64.h:35:17: note: expected 'uint64_t *' but argument is of type 'long unsigned int *'
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for the output sample rates 96kHz and 192kHz.
Tested with a Cubox-i imx6 system and an Onkyo TX-SR607 receiver.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
1) Apply better indentations
2) Drop braces for single statement.
3) Use simpler ternary to reduce code.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 432481220 (ASoC: fsl-ssi: Use regmap) removed struct ccsr_ssi.
Unfortunately, the structure is still used. This causes
mpc85xx_smp_defconfig and mpc85xx_defconfig builds to fail with
sound/soc/fsl/fsl_dma.c:926:50:
error: invalid use of undefined type 'struct ccsr_ssi'
dma->ssi_stx_phys = res.start + offsetof(struct ccsr_ssi, stx0);
ound/soc/fsl/fsl_dma.c:927:50:
error: invalid use of undefined type 'struct ccsr_ssi'
dma->ssi_srx_phys = res.start + offsetof(struct ccsr_ssi, srx0);
Fix by using constants, similar to original commit.
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
The calculation code does
u64 = (u32 - u32) * 100000;
The 64 bits are of no help here as the type is casted only after the
multiplication, and therefore the result may overflow, possibly causing
inoptimal or wrong clock setup in an unfortunate case (the maximum
result value of the first substraction is currently 47999).
Fix the code to cast before multiplication.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We should not copy the return value into this val since it's supposed to
get the value of the register not the success result of regmap_read().
Thus fix it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Eukrea-i.MX51 board was converted to use DT, ie we no longer have a
MACH_EUKREA_MBIMXSD51_BASEBOARD symbol.
Transformation of other boards planned for the near future, so this
patch removes all these dependencies and restricts build of this
driver to ARCH_MXC.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch replaces the ssi specific functions write_ssi, read_ssi and
write_ssi_mask by standard regmap function calls.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Reorder all variables in struct fsl_ssi_private to have groups that make
sense together. The patch also updates the struct documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The baudclock may be used and set by different streams.
Allow only the first stream to set the bitclock rate. Other streams have
to try to get to the correct rate without modifying the bitclock rate
using the SSI internal clock modifiers.
The variable baudclk_streams is introduced to keep track of the active
streams that are using the baudclock. This way we know if the baudclock
may be set and whether we may enable/disable the clock.
baudclock enable/disable is moved to hw_params()/hw_free(). This way we can
keep track of the baudclock in those two functions and avoid a running
clock while it is not used. As hw_params()/hw_free() may be called
multiple times for the same stream, we have to use baudclk_streams
variable to know whether we may enable/disable the clock.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In i2s master mode the fsl_ssi driver depends on someone calling
.set_tdm_slot correctly. In this mode though only a DC value of
2 is allowed, so set it in this case and no longer depend on
.set_tdm_slot.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The baudclock_locked variable is only used in functions which
are serialized anyway from the core. No need to have a lock
around the variable, so remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The fsl_ssi driver uses the .set_sysclk callback to configure the
bitclock for master mode. This is unnecessary since the bitclock
is known in hw_params. This patch configures the bitclock from .hw_params.
.set_dai_sysclk now sets a bitclock frequency which is preferred over
the default calculated bitclock frequency.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The simple soundcard binding has its own way for specifying the dai
format. To be able to use this binding we have to make the fsl,mode
property optional. As the property is used in existing devicetrees
keep the option around for compatibility reasons.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Introduce a SoC data struct which contains the differences between
the different SoCs this driver supports. This makes it easy to support
more differences without having to introduce a new switch/case each
time.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
fsl_ssi_set_dai_sysclk will be called from fsl_ssi_hw_params in the
next patch. Move up to avoid forward declaration and to keep the next patch
more readable. No functional change.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the fsl-ssi unit is used in i2s slave mode, it is possible that the
SSI unit starts transmitting data on the wrong channel. This happens
because the SSI does not synchronize with the left-right-clock by
default.
This patch enables transmit enable synchronization.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are some variables defined in struct fsl_ssi_private that describe
states that are also described by other variables.
This patch adds some helper functions that return exactly the same
information based on available variables. This helps to clean up struct
fsl_ssi_private and remove them from the probe function.
It also removes some not really used variables (new_binding, name).
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Reorder the probe function to be able to move the second imx-specific
block to the seperate imx probe function. The patch also removes some
comments/variables/code that are not used anymore or could be simply
replaced by other variables.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify dma DT property handling. fsl,ssi-dma-events is not used
anymore. It passes invalid data to imx_pcm_dma_params_init_data() which
copies some data into an imx dma struct. This struct is never used in
imx-dma or imx-sdma because of generic OF DMA handling. The
"fsl,ssi-dma-events" is not used anywhere in dts files.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move imx specific probe code to a seperate function. It reduces the
size of the probe() function and makes the code and error handling
easier to understand.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of creating a name using string manipulation functions, we can
simply use the device name for the DAI driver struct.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move all code that is only used for debugging to a seperate file. This
makes it easier to see what functions are used for debugging only.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The bits we have to clear when disabling are different when the other
stream is still active.
This patch fixes the calculation of new register values after disabling
one stream. It also adds a more detailed description of the new register
value calculation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We don't need to change those dividers if bclk and mclk remains the same
directions and values.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
According to Reference Manual -- ESAI Initialization chapter, as the
standard procedure of ESAI personal reset, the PCRC and PRRC registers
should be remained in its reset value and then configured after T/RCCR
and T/RCR configurations's done but before TE/RE's enabling.
So this patch moves PCRC and PRRC settings to the end of hw_params().
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ESAI can only output EXTAL clock source directly. But for FSYS clock source,
ESAI can not output it without getting through PSR PM dividers.
So this patch adds an extra check in the code.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The range here from 1 to 16 is confined to FP divider only while the
sck_div indicates if the calculation contains PSR and PM dividers. So
for the case using PSR and PM since the sck_div is true, the range of
ratio would simply become bigger than 16.
So this patch fixes the condition here and adds one line comments to
make the purpose here clear.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Other people would clearly understand each member and improve if they want.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
People would simply know what the driver gets the best for the current
sample rate playback.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The sysclk is one the clock sources that could be selected to derive
tx clock. But the route for sysclk is a bit different that it does
not only contain txclk df divider but also have an extra sysclk df.
So this patch mainly adds syclk df configuration support so as to
let the driver be able to get clock from sysclk.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We should have used _df by following the reference manual at the beginning.
So this patch just renames them.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The clock mux for the Freescale S/PDIF controller has eight clock sources
while most of them are from other moudles and even system clocks that do
not allow a rate-changing operation.
So we here only allow the clk_set_rate() and clk_round_rate() happened to
spdif root clock, the private clock for S/PDIF controller.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 204dec93ea "ASoC: fsl: Allow to select individual common
options", it is possible to enable SND_SOC_FSL_SSI and SND_SOC_FSL_SPDIF
manually, either as loadable modules or built-in. This unfortunately
leads to a link error if one or both of them are built-in, while
the imx-pcm-dma framework is a loadable module:
sound/built-in.o: In function `fsl_ssi_probe':
:(.text+0x51fb8): undefined reference to `imx_pcm_dma_init'
sound/built-in.o: In function `fsl_spdif_probe':
:(.text+0x52e20): undefined reference to `imx_pcm_dma_init'
This changes Kconfig to prevent this case by using 'select' to turn
on the imx-pcm-dma code from both drivers. For consistency, we also
turn on the imx-pcm-fiq code, which is an alternative to the dma
implementation.
Note that imx-pcm-fiq is platform dependent, so we must not enable
that unless we are building a kernel for i.MX. Note also the
"if SND_IMX_SOC != n" syntax as opposed to the normal "if SND_IMX_SOC".
This is needed to avoid turning on the options as 'm' if 'SND_IMX_SOC'
is a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This will be useful for out-of-tree drivers since in-tree drivers
could select it automatically.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This will be useful for out-of-tree drivers since in-tree drivers
could select it automatically.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Building ARM randconfig got into a situation where CONFIG_INPUT
is turned off and SND_SOC_ALL_CODECS is turned on, which failed
for two codecs trying to use the input subsystem. Some other
drivers also select one of these codecs and consequently need an
explicit dependency added.
Appending to the dependency list seems the easiest way out,
since this is not a practical limitation. If anyone really
needs to build these codecs for a kernel with no input support,
a more sophisticated solution can be implemented.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Xia Kaixu <kaixu.xia@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The rxclk rate actually uses sysclk, ipg clock for example, as its
reference clock to calculate it. But the driver currently doesn't
pass a correct clock source. So fix it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now ASoC core is getting the intersection of supported formats not only
from CPU and CODEC dai's but also from DMA's. However, there should be
no specific width limitation from SDMA side.
So drop it. Otherwise, we would only support S16_LE format for all i.MX
platforms.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Regmap is able to enable/disable the core clock automatically each time
it's going to access the registers. But for DMA cases during playback or
recording, it's totally beyong control of regmap. So we have to open the
clock manually.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
audmux_debugfs_init() is marked as __init, but is called from imx_audmux_probe()
which is not marked as __init. This creates a section mismatch and a potential
runtime crash (if imx_audmux_probe() is called after the .init section was
dropped). This patch removes the __init annotation from audmux_debugfs_init(),
which fixes the following warning:
WARNING: sound/soc/built-in.o(.text+0x86960): Section mismatch in reference
from the function imx_audmux_probe() to the function
.init.text:audmux_debugfs_init()
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
It should use STC_SYSCLK_DIV_OFFSET. Thus fix it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Hopefully fixing a build failure reported by Stephen Rothwell - though
quite why the other OF headers don't include this as well I'm not sure.
Signed-off-by: Mark Brown <broonie@linaro.org>
By doing this, the driver can drop around 50 lines and become neater.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the precise definition of 'ret', which will be used for
the error check.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Patch ASoC: fsl_sai: Fix buggy configurations in trigger() doesn't entirely
fix the condition: FRDE of the current substream direction is being cleared
while the code is still using the non-updated one.
Thus this patch fixes this issue by checking the opposite one's FRDE alone
since the current one's is absolutely disabled.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In fsl_ssi_hw_params() we update the I2S and NET bits using the i2s_mode
variable. The fsl_ssi_set_dai_fmt() function only writes the i2s-mode to
the i2s_mode variable and not the NET bit. This fixes it by adding that
bit to i2s_mode.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
fsl_ssi_set_dai_fmt() manages most of the register setup routines now.
fsl_ssi_setup() makes the same as fsl_ssi_set_dai_fmt() but it relies on
DT properties.
In most cases the settings of fsl_ssi_setup() are already overwritten by
fsl_ssi_set_dai_fmt() when it is called by the soc-core when a sound
card is added. As these settings depend on the combination of codec and
cpu DAI, this should really be done by sound cards.
This patch removes fsl_ssi_setup() and adds the missing register setups
to fsl_ssi_set_dai_fmt(). It also removes all calls to fsl_ssi_setup().
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SAI mainly has the following clocks:
bus clock
control and configure registers and to generate synchronous
interrupts and DMA requests.
mclk1, mclk2, mclk3
to generate the bit clock when the receiver or transmitter is
configured for an internally generated bit clock.
So this patch adds these clocks and their clock controls to the driver.
[ To concern the old DTB cases, I've added a bit of extra code to make
the driver compatible with them. And by marking clock NULL if failed
to get, the clk_prepare() or clk_get_rate() would easily return 0
so no further path should be broken. -- by Nicolin ]
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The next coming i.MX6 Solo X SoC also contains SAI module while we use
imp_pcm_init() for i.MX platform.
So this patch adds one compatible route for imx6sx and updates the DT
doc accordingly.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We only enable one side interrupt for each stream since over/underrun
on the opposite stream would be resulted from what we previously did,
enabling TERE but remaining FRDE disabled, even though the xrun on the
opposite direction will not break the current stream.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The current trigger() has two crucial problems:
1) The DMA request enabling operations (FSL_SAI_CSR_FRDE) for Tx and Rx are
now totally exclusive: It would fail to run simultaneous Tx-Rx cases.
2) The TERE disabling operation depends on an incorrect condition -- active
reference count that only gets increased in snd_pcm_open() and decreased
in snd_pcm_close(): The TERE would never get cleared.
So this patch overwrites the trigger function by following these rules:
A) We continue to support tx-async-while-rx-sync-to-tx case alone, which's
originally limited by this fsl_sai driver, but we make the code easy to
modify for the further support of the opposite case.
B) We enable both TE and RE for PLAYBACK stream or CAPTURE stream but only
enabling the DMA request bit (FSL_SAI_CSR_FRDE) of the current direction
due to the requirement of SAI -- For tx-async-while-rx-sync-to-tx case,
the receiver is enabled only when both the transmitter and receiver are
enabled.
Tested cases:
a) aplay test.wav -d5
b) arecord -r44100 -c2 -fS16_LE test.wav -d5
c) arecord -r44100 -c2 -fS16_LE -d5 | aplay
d) (aplay test2.wav &); sleep 1; arecord -r44100 -c2 -fS16_LE test.wav -d1
e) (arecord -r44100 -c2 -fS16_LE test.wav -d5 &); sleep 1; aplay test.wav -d1
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch improves fsl_sai_isr() in these ways:
1, Add comment for mask fetching code.
2, Return IRQ_NONE if the IRQ is not for the device.
3, Use regmap_write() instead of regmap_update_bits().
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch allow to select individual common sound options and
as a result allow using sound cards/codecs based on DT description.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch provide separation of the main audio options and boards.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
The BCP bit in TCR4/RCR4 register rules as followings:
0 Bit clock is active high with drive outputs on rising edge
and sample inputs on falling edge.
1 Bit clock is active low with drive outputs on falling edge
and sample inputs on rising edge.
For all formats currently supported in the fsl_sai driver, they're exactly
sending data on the falling edge and sampling on the rising edge.
However, the driver clears this BCP bit for all of them which results click
noise when working with SGTL5000 and big noise with WM8962.
Thus this patch corrects the BCP settings for all the formats here to fix
the nosie issue.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Acked-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It's quite cricial to clear error flags because SAI might hang if getting
FIFO underrun during playback (I haven't confirmed the same issue on Rx
overflow though).
So this patch enables those irq and adds isr() to clear the flags so as to
keep playback entirely safe.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch add .xlate_tdm_slot_mask support for IMX SSI, and this
will generate the TDM slot TX and RX masks.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch add .xlate_tdm_slot_mask support for ESAI, and this will
generate the TDM slot TX and RX masks.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch add fsl_asoc_xlate_tdm_slot_mask() support for utils.
For the some spcified DAI driver, this will be used to generate the
TDM slot TX/RX mask. And the TX/RX mask will use a 0 bit for an active
slot as default, and the default active bits are at the LSB of
the masks.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that AIC23 supports two control interfaces all existing I2C users
should select I2C variant.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no point in using FIQ if DMA is available (it is selected) and
selecting FIQ currently breaks the build on non-i.MX platforms. If FIQ
is actually required the build will need to be restricted or have a
select for the relevant FIQ code adding.
Signed-off-by: Mark Brown <broonie@linaro.org>
Use table based setup to register the DAPM widgets and routes. This on one hand
makes the code a bit shorter and cleaner and on the other hand the board level
DAPM elements get registered in the card's DAPM context rather than in the
CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: alsa-devel@alsa-project.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
o Add SND_SOC_DAIFMT_DSP_A support.
o Add SND_SOC_DAIFMT_DSP_B support.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
o Fix some bugs of fsl_sai_set_dai_fmt_tr().
o Add SND_SOC_DAIFMT_LEFT_J support.
o Add SND_SOC_DAIFMT_CBS_CFM support.
o Add SND_SOC_DAIFMT_CBM_CFS support.
o And SND_SOC_DAIFMT_RIGHT_J need to be done in the future.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of jumping to the 'out' label, just return the error code immediately.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For most platforms, the CPU and ESAI device is in the same endianess
mode. While for the LS1 platform, the CPU is in LE mode and the ESAI
is in BE mode.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For most platforms, the CPU and SPDIF device is in the same endianess
mode. While for the LS1 platform, the CPU is in LE mode and the SPDIF
is in BE mode.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since the Freescale SAI, ESAI and SPDIF are using the regmap-mmio,
there needs a select of REGMAP_MMIO in the Kconfig to ensure that
regmap-mmio is actually enabled.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The commit 1abe729 (ASoC: fsl: Add missing pm to current machine
drivers) enables pm support for a few IMX machine drivers. But it does
not update dev drvdata to be the pointer to 'card'. This causes the
kernel dump below in system suspend, because snd_soc_suspend() expects
that the dev drvdata points to 'card', while it still points to the
private data of machine driver.
This patch fixes imx-sgtl5000 and imx-wm8962 by attaching 'card' to dev
drvdata and private data to card drvdata. For imx-mc13783, I simply
revert the pm change because it must be broken for the same reason and
I don't have hardware to test pm enabling code.
$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
mmc1: card e624 removed
Freezing user space processes ... (elapsed 0.002 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
PM: Entering mem sleep
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 1861 Comm: bash Not tainted 3.14.0-rc1+ #1648
Backtrace:
[<80012144>] (dump_backtrace) from [<800122e4>] (show_stack+0x18/0x1c)
r6:8079c77c r5:00000c5a r4:00000000 r3:00000000
[<800122cc>] (show_stack) from [<80637ac0>] (dump_stack+0x78/0x94)
[<80637a48>] (dump_stack) from [<80028918>] (warn_slowpath_common+0x6c/0x8c)
r4:bdb21c38 r3:be62df00
[<800288ac>] (warn_slowpath_common) from [<800289dc>] (warn_slowpath_fmt+0x38/0x40)
r8:be62e3a8 r7:bf122960 r6:00000005 r5:00000000 r4:00000000
[<800289a8>] (warn_slowpath_fmt) from [<8006518c>] (__lock_acquire+0x1ae0/0x1ce0)
r3:8079d598 r2:80799e70
[<800636ac>] (__lock_acquire) from [<80065894>] (lock_acquire+0x68/0x7c)
r10:bdb20000 r9:be62df00 r8:00000000 r7:00000000 r6:60000013 r5:bdb20000
r4:00000000
[<8006582c>] (lock_acquire) from [<8063c938>] (mutex_lock_nested+0x5c/0x3b8)
r7:00000000 r6:80dfc78c r5:804be444 r4:bf122928
[<8063c8dc>] (mutex_lock_nested) from [<804be444>] (snd_soc_suspend+0x34/0x42c)
r10:00000000 r9:00000000 r8:00000000 r7:bf1c4444 r6:bf1c4410 r5:be978150
r4:be978010
[<804be410>] (snd_soc_suspend) from [<8034392c>] (platform_pm_suspend+0x34/0x64)
r10:00000000 r8:00000000 r7:bf1c4444 r6:bf1c4410 r5:803438f8 r4:bf1c4410
[<803438f8>] (platform_pm_suspend) from [<80348e18>] (dpm_run_callback.isra.7+0x34/0x6c)
[<80348de4>] (dpm_run_callback.isra.7) from [<80349354>] (__device_suspend+0x10c/0x220)
r9:808dd974 r8:808c4a5c r6:00000002 r5:80e5001c r4:bf1c4410
[<80349248>] (__device_suspend) from [<8034a338>] (dpm_suspend+0x60/0x220)
r7:bf1c4410 r6:808dd90c r5:80e5001c r4:bf1c44c0
[<8034a2d8>] (dpm_suspend) from [<8034a790>] (dpm_suspend_start+0x60/0x68)
r10:8079a818 r9:00000000 r8:00000004 r7:80dfbe90 r6:80641eec r5:00000000
r4:00000002
[<8034a730>] (dpm_suspend_start) from [<8006a788>] (suspend_devices_and_enter+0x74/0x318)
r4:00000003 r3:80dfbe98
[<8006a714>] (suspend_devices_and_enter) from [<8006abd8>] (pm_suspend+0x1ac/0x244)
r10:8079a818 r8:00000004 r7:00000003 r6:80641eec r5:00000000 r4:00000003
[<8006aa2c>] (pm_suspend) from [<80069a4c>] (state_store+0x70/0xc0)
r5:00000003 r4:bd85ea40
[<800699dc>] (state_store) from [<80294034>] (kobj_attr_store+0x1c/0x28)
r10:beb9fe08 r8:00000000 r7:bdb21f78 r6:bd85ea40 r5:00000004 r4:beb9fe00
[<80294018>] (kobj_attr_store) from [<80140f90>] (sysfs_kf_write+0x54/0x58)
[<80140f3c>] (sysfs_kf_write) from [<8014474c>] (kernfs_fop_write+0xc4/0x160)
r6:bd85ea40 r5:beb9fe00 r4:00000004 r3:80140f3c
[<80144688>] (kernfs_fop_write) from [<800dfa14>] (vfs_write+0xbc/0x184)
r10:00000000 r9:00000000 r8:00000000 r7:bdb21f78 r6:00500c08 r5:00000004
r4:be782600
[<800df958>] (vfs_write) from [<800dfe00>] (SyS_write+0x48/0x70)
r10:00000000 r8:00000000 r7:00000004 r6:00500c08 r5:00000000 r4:be782600
[<800dfdb8>] (SyS_write) from [<8000e800>] (ret_fast_syscall+0x0/0x48)
r9:bdb20000 r8:8000e9c4 r7:00000004 r6:00500c08 r5:00000004 r4:76eb65e0
Fixes: 1abe729 (ASoC: fsl: Add missing pm to current machine drivers)
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The big chunks here are the updates for oxygen driver for Xonar DG
devices, which were slipped from the previous pull request. They are
device-specific and thus not too dangerous.
Other than that, all patches are small bug fixes, mainly for Samsung
build fixes, a few HD-audio enhancements, and other misc ASoC fixes.
(And this time ASoC merge is less than Octopus, lucky seven :)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=QB98
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The big chunks here are the updates for oxygen driver for Xonar DG
devices, which were slipped from the previous pull request. They are
device-specific and thus not too dangerous.
Other than that, all patches are small bug fixes, mainly for Samsung
build fixes, a few HD-audio enhancements, and other misc ASoC fixes.
(And this time ASoC merge is less than Octopus, lucky seven :)"
* tag 'sound-fix-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (42 commits)
ALSA: hda/hdmi - allow PIN_OUT to be dynamically enabled
ALSA: hda - add headset mic detect quirks for another Dell laptop
ALSA: oxygen: Xonar DG(X): cleanup and minor changes
ALSA: oxygen: Xonar DG(X): modify high-pass filter control
ALSA: oxygen: Xonar DG(X): modify input select functions
ALSA: oxygen: Xonar DG(X): modify capture volume functions
ALSA: oxygen: Xonar DG(X): use headphone volume control
ALSA: oxygen: Xonar DG(X): modify playback output select
ALSA: oxygen: Xonar DG(X): capture from I2S channel 1, not 2
ALSA: oxygen: Xonar DG(X): move the mixer code into another file
ALSA: oxygen: modify CS4245 register dumping function
ALSA: oxygen: modify adjust_dg_dac_routing function
ALSA: oxygen: Xonar DG(X): modify DAC/ADC parameters function
ALSA: oxygen: Xonar DG(X): modify initialization functions
ALSA: oxygen: Xonar DG(X): add new CS4245 SPI functions
ALSA: oxygen: additional definitions for the Xonar DG/DGX card
ALSA: oxygen: change description of the xonar_dg.c file
ALSA: oxygen: export oxygen_update_dac_routing symbol
ALSA: oxygen: add mute mask for the OXYGEN_PLAY_ROUTING register
ALSA: oxygen: modify the SPI writing function
...
Pull slave-dma updates from Vinod Koul:
- new driver for BCM2835 used in R-pi
- new driver for MOXA ART
- dma_get_any_slave_channel API for DT based systems
- minor fixes and updates spread acrooss driver
[ The fsl-ssi dual fifo mode support addition clashed badly with the
other changes to fsl-ssi that came in through the sound merge. I did
a very rough cut at fixing up the conflict, but Nicolin Chen (author
of both sides) will need to verify and check things ]
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (36 commits)
dmaengine: mmp_pdma: fix mismerge
dma: pl08x: Export pl08x_filter_id
acpi-dma: align documentation with kernel-doc format
dma: fix vchan_cookie_complete() debug print
DMA: dmatest: extend the "device" module parameter to 32 characters
drivers/dma: fix error return code
dma: omap: Set debug level to debugging messages
dmaengine: fix kernel-doc style typos for few comments
dma: tegra: add support for Tegra148/124
dma: dw: use %pad instead of casting dma_addr_t
dma: dw: join split up messages
dma: dw: fix style of multiline comment
dmaengine: k3dma: fix sparse warnings
dma: pl330: Use dma_get_slave_channel() in the of xlate callback
dma: pl330: Differentiate between submitted and issued descriptors
dmaengine: sirf: Add device_slave_caps interface
DMA: Freescale: change BWC from 256 bytes to 1024 bytes
dmaengine: Add MOXA ART DMA engine driver
dmaengine: Add DMA_PRIVATE to BCM2835 driver
dma: imx-sdma: Assign a default script number for ROM firmware cases
...
New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et. al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL' removal,
unused uninitialised warning mitigation, error message clarity,
removal of redundant/duplicate checks, licensing (GPL -> GPL2),
coding consistency, duplicate function declaration, ret checks,
commit corrections, redundant of_match_ptr() helper removal,
spelling, #if-deffery removal and header guards name changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=PuTE
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd
Pull MFD changes from Lee Jones:
"New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
removal, unused uninitialised warning mitigation, error
message clarity, removal of redundant/duplicate checks,
licensing (GPL -> GPL2), coding consistency, duplicate
function declaration, ret checks, commit corrections,
redundant of_match_ptr() helper removal, spelling,
#if-deffery removal and header guards name changes"
* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
mfd: wm5110: Add register patch for rev D chip
mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
gpio: lp3943: Remove redundant of_match_ptr helper
mfd: sta2x11-mfd: Use named constants for pci_power_t values
Documentation: mfd: Fix LDO index in s2mps11.txt
mfd: Cleanup mfd-mcp-sa11x0.h header
mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
mfd: twl6030: Fix endianness problem in IRQ handler
mfd: sec-core: Add cells for S5M8767-clocks
mfd: max14577: Remove redundant of_match_ptr helper
mfd: twl6040: Fix sparse non static symbol warning
mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
mfd: rtsx: Fix sparse non static symbol warning
mfd: max77693: Set proper maximum register for MUIC regmap
mfd: max77686: Fix regmap resource leak on driver remove
mfd: Represent correct filenames in file headers
mfd: rtsx: Add support for card reader rtl8402
mfd: rtsx: Add set pull control macro and simplify rtl8411
mfd: max8997: Enforce mfd_add_devices() return value check
mfd: mc13xxx: Simplify probe() & remove()
...
Currently everytime we get the following message on boot:
fsl-ssi-dai 202c000.ssi: could not get baud clock: -2
This is not really useful information to get on every boot, so make it a debug
message instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit aafa85e71a (ASoC: fsl_ssi: Add DAI master mode support for SSI on
i.MX series) master mode is supported, so update the comments and code to
reflect that.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Symbol MFD_MC13783 always selected by MFD_MC13XXX, so no need
to keep additional symbol.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
SNDRV_PCM_RATE_CONTINUOUS means that all rates (possibly limited to a certain
interval) are supported. There is no need to manually set other rate bits.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch implements a device-tree-only CPU DAI driver for Freescale ESAI
controller that supports:
- 12 channels playback and 8 channels record.
[ Some of the inner transmitters and receivers are sharing same group of
pins. So the maxmium 12 output or 8 input channels are only valid if
there is no pin conflict occurring to it. ]
- Independent (asynchronous mode) or shared (synchronous mode) transmit and
receive sections with separate or shared internal/external clocks and frame
syncs, operating in Master or Slave mode.
[ Current ALSA seems not to allow CPU DAI drivers to configure DAI format
separately for PLAYBACK and CAPTURE. So this first version only supports
the case that uses the same DAI format for both directions. ]
- Various DAI formats: I2S, Left-Justified, Right-Justified, DSP-A and DSP-B.
- Programmable word length (8, 16, 20 or 24bits)
- Flexible selection between system clock or external oscillator as input
clock source, programmable internal clock divider and frame sync generation.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For those platforms using DAI master mode like I2S, it's better to pre-set
a default slot number so that there's no need for these common cases to set
the slot number from its machine driver any more.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add the missing clk_disable_unprepare() before return from
fsl_ssi_probe() in the request irq error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
single_open requires a function with signature
'int (*)(struct seq_file *, void *)'. This patch fixes the warning by
fixing the wrong return type of fsl_ssi_stats_show.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The normal trigger function can now be used for AC97. Drop AC97 trigger
function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch defines the appropriate register values for different
oparation modes and IP versions. We have to handle DMA/FIQ, AC97,
DEBUG-IRQs and offline/online configuration support.
With this patch we cleanup some driver code that was not reference
manual conform and try to cleanup the whole trigger function to seperate
the actual register values from the enable/disable logic, which is now
hidden in fsl_ssi_config helpers.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a struct 'fsl_ssi_rxtx_reg_val' which holds register
values necessary to enable rx/tx. Based on those preset register values,
the added configuration functions will cleanly enable/disable different
parts of the SSI IP while supporting online/offline configuration.
Different operating modes can be setup directly as different register
values in fsl_ssi_reg_val.
These functions and structs will help to cleanup and simplify the
trigger function to support many different IP versions (online/offline
configuration) and different operating modes.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
imx50-ssi and later versions of this IP support online reconfiguration
of all registers. The reference manual does not list any registers that
can only be configured while the SSI unit is disabled. This patch
introduces the flag for later use.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
irqs should only be requested/released with enabled DMA. Previously
interrupt statistics where disabled for IMX Processors because of
different writeable SISR bits.
This patch introduces support for irqstats on imx processors again by
creating a sisr writeback mask and introducing a imx35-ssi compatible.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a small but significant difference between imx21-ssi and
imx51-ssi and above. imx21-ssi does not allow online reconfiguration of
some registers. They have to be configured at the beginning.
imx51-ssi has to reconfigure the SSI unit while it is running. Otherwise
it would not be possible to have two streams in parallel. The new SDMA
unit in imx51 and above has to be configured before the first DMA
request arrives. Therefor we need to setup TDMAE/RDMAE just before
starting the stream.
This patch introduces distinct imx51-ssi as compatible and adds
of_device_id matching in the probe function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Interrupt statistics of fsl_ssi are mainly for debugging purpose. Most
of those interrupts show error states, e.g. under/overflow.
The stats should be exposed via debugfs instead of sysfs.
This patch moves the statistics file to debugfs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the error handling in the fsl-ssi probe function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 6873ee464a (ASoC: fsl_ssi: Fix printing return code on clk error) caused
the following build warning:
sound/soc/fsl/fsl_ssi.c: In function 'fsl_ssi_probe':
sound/soc/fsl/fsl_ssi.c:1196:6: warning: format '%d' expects argument of type 'int', but argument 3 has type 'long int' [-Wformat]
Fix it by using '%ld' to print the 'long int' format.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Nicolin Chen