Add OOB layout description for docg3, so that userspace can
use this information to setup the data for write_oob().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for multiple floors, ie. cascaded docg3
chips. There might be 4 docg3 chips cascaded, sharing the
same address space, and providing up to 4 times the storage
capacity of a unique chip.
Each floor will be seen as an independant mtd device.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the docg3 reads to be able to cope with all possible
data buffer / oob buffer / file mode combinations from
docg3_read_oob().
This especially ensures that raw reads do not use ECC
corrections, and AUTOOOB and PLACEOOB do use ECC
correction.
The approach is to empty docg3_read() and make it a wrapper
to docg3_read_oob(). As docg3_read_oob() handles all the
funny cases (no data buffer but oob buffer, data buffer but
no oob buffer, ...), docg3_read() is just a special use of
docg3_read_oob().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The protection areas boundaries were on 16bit registers, not
8bit. This is consistent with block numbers, which can
extend up to 4096 on bigger chips (and is 2048 on the
docg3).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Writeb was incorrectly traced as a 16 bits write, instead of
a 8 bits write. Fix it by tracing the correct width.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Change the NOP debug log verbosity to very verbose to
unburden log analysis.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for DiskOnChip G3 chips. The support is quite
limited yet :
- no flash writes/erases are implemented
- ECC fixes are not implemented
- powerdown is not implemented
- IPL handling is not yet done
On the brighter side, the chip reading does work.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Robert Jarzmik