Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This assignment is done by the snd_soc_register_codec so there is no need
to redo it in probe function of a codec driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For digital only paths we need to make sure the bandgap is enabled prior
to starting the FLL which isn't tied into DAPM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The WM8996 can measure the impedance of accessories connected to the
headphone output. Implement initial support for this, measuring the
left channel impedance when an accessory is detected and using this
to distinguish between a line load and a headphone load.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Rather than managing the bandgap in the bias level control use a supply
widget as we only actually need to enable it for analogue paths, not
fully digital ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We need to count the timeout down.
Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The AIF1 channels are numbered from zero than one; do the same thing for
AIF2 too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The WM8996 only requires CPVDD when the charge pump is active so control
it separately to the other supplies, only enabling it when the charge pump
is active. This will result in a small power saving on systems which are
able to provide independent software control of the supply.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We can directly read the FLL lock status on WM8996 so even if we don't
have an interrupt wired up we can still verify that the FLL started
successfully.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
My first patch to ASoC ever! If I did something wrong, blame Ian.
Signed-off-by: Susan Gao <sgao@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In case we have a pending completion, for example due to a problem with
the input clock which got corrected after we timed out.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This occurs frequently if we are in edge triggered mode as we must poll the
interrupt status register until we get no more interrupts so it's worth
the effort - it means we skip writing null acknowledgements to the chip.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
For non-audio uses like accessory detection we can use a lower quality,
unregulated microphone bias, saving a little power. As the hardware can
manually enable and disable the biases we can select regulating mode
automatically with supply widgets connected to the biases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
There's no need for separate widgets for the enables (as the map already
shows).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Make AIFCLK supply the record paths otherwise record will not work unless
there is a simultaneous playback.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This closes the small race between a status being read in response to an
interrupt and clearing the interrupt, meaning that if the status changes
between those periods we might not get a reassertion of the interrupt.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Axel Lin