dm-crypt consumes an excessive amount memory when the user attempts to
zero a dm-crypt device with "blkdiscard -z". The command "blkdiscard -z"
calls the BLKZEROOUT ioctl, it goes to the function __blkdev_issue_zeroout,
__blkdev_issue_zeroout sends a large amount of write bios that contain
the zero page as their payload.
For each incoming page, dm-crypt allocates another page that holds the
encrypted data, so when processing "blkdiscard -z", dm-crypt tries to
allocate the amount of memory that is equal to the size of the device.
This can trigger OOM killer or cause system crash.
Fix this by limiting the amount of memory that dm-crypt allocates to 2%
of total system memory. This limit is system-wide and is divided by the
number of active dm-crypt devices and each device receives an equal
share.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Could be useful for a target to return stats or other information.
If a target does DMEMIT() anything to @result from its .message method
then it must return 1 to the caller.
Signed-off-By: Mike Snitzer <snitzer@redhat.com>
walk; this is critical to allow forward progress without the need to
use the bioset's BIOSET_NEED_RESCUER.
- Remove DM core's BIOSET_NEED_RESCUER based dm_offload infrastructure.
- DM core cleanups and improvements to make bio-based DM more efficient
(e.g. reduced memory footprint as well leveraging per-bio-data more).
- Introduce new bio-based mode (DM_TYPE_NVME_BIO_BASED) that leverages
the more direct IO submission path in the block layer; this mode is
used by DM multipath and also optimizes targets like DM thin-pool that
stack directly on NVMe data device.
- DM multipath improvements to factor out legacy SCSI-only
(e.g. scsi_dh) code paths to allow for more optimized support for NVMe
multipath.
- A fix for DM multipath path selectors (service-time and queue-length)
to select paths in a more balanced way; largely academic but doesn't
hurt.
- Numerous DM raid target fixes and improvements.
- Add a new DM "unstriped" target that enables Intel to workaround
firmware limitations in some NVMe drives that are striped internally
(this target also works when stacked above the DM "striped" target).
- Various Documentation fixes and improvements.
- Misc. cleanups and fixes across various DM infrastructure and targets
(e.g. bufio, flakey, log-writes, snapshot).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJacgwPAAoJEMUj8QotnQNaEw0H/0XRTcg8/lRuGl46kdeI3PgR
ZxUy4XgUrCLiACWO5yCU/nKipB32+3xTlTDTBcjmaBfX8HolH147Pasb1KdHqLVC
dOWLMpjlFztb5fnuOMitJA05qQAbgRlZ52QdVk/FDo9yWicgWjQZduh8aYX53pHw
6XOYWzSFAXQcaduPdz6TLiPw479xBwIpXxQbrO09f4qt3Ub4bqknEhzFXc+6M7zl
ejmW/bG2Qg6WmsfAuaAhFTV0LpTPSEzvaq9TfR7yqFU3DvDIAi7Yh8eQinIUDo4u
txpOGoESRAMPAMKH0/UJdr/u7jTsfgJox4QEavWfnViPvkouah5KdjVOL1veZ5U=
=R3dN
-----END PGP SIGNATURE-----
Merge tag 'for-4.16/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- DM core fixes to ensure that bio submission follows a depth-first
tree walk; this is critical to allow forward progress without the
need to use the bioset's BIOSET_NEED_RESCUER.
- Remove DM core's BIOSET_NEED_RESCUER based dm_offload infrastructure.
- DM core cleanups and improvements to make bio-based DM more efficient
(e.g. reduced memory footprint as well leveraging per-bio-data more).
- Introduce new bio-based mode (DM_TYPE_NVME_BIO_BASED) that leverages
the more direct IO submission path in the block layer; this mode is
used by DM multipath and also optimizes targets like DM thin-pool
that stack directly on NVMe data device.
- DM multipath improvements to factor out legacy SCSI-only (e.g.
scsi_dh) code paths to allow for more optimized support for NVMe
multipath.
- A fix for DM multipath path selectors (service-time and queue-length)
to select paths in a more balanced way; largely academic but doesn't
hurt.
- Numerous DM raid target fixes and improvements.
- Add a new DM "unstriped" target that enables Intel to workaround
firmware limitations in some NVMe drives that are striped internally
(this target also works when stacked above the DM "striped" target).
- Various Documentation fixes and improvements.
- Misc cleanups and fixes across various DM infrastructure and targets
(e.g. bufio, flakey, log-writes, snapshot).
* tag 'for-4.16/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (69 commits)
dm cache: Documentation: update default migration_throttling value
dm mpath selector: more evenly distribute ties
dm unstripe: fix target length versus number of stripes size check
dm thin: fix trailing semicolon in __remap_and_issue_shared_cell
dm table: fix NVMe bio-based dm_table_determine_type() validation
dm: various cleanups to md->queue initialization code
dm mpath: delay the retry of a request if the target responded as busy
dm mpath: return DM_MAPIO_DELAY_REQUEUE if QUEUE_IO or PG_INIT_REQUIRED
dm mpath: return DM_MAPIO_REQUEUE on blk-mq rq allocation failure
dm log writes: fix max length used for kstrndup
dm: backfill missing calls to mutex_destroy()
dm snapshot: use mutex instead of rw_semaphore
dm flakey: check for null arg_name in parse_features()
dm thin: extend thinpool status format string with omitted fields
dm thin: fixes in thin-provisioning.txt
dm thin: document representation of <highest mapped sector> when there is none
dm thin: fix documentation relative to low water mark threshold
dm cache: be consistent in specifying sectors and SI units in cache.txt
dm cache: delete obsoleted paragraph in cache.txt
dm cache: fix grammar in cache-policies.txt
...
Pull block updates from Jens Axboe:
"This is the main pull request for block IO related changes for the
4.16 kernel. Nothing major in this pull request, but a good amount of
improvements and fixes all over the map. This contains:
- BFQ improvements, fixes, and cleanups from Angelo, Chiara, and
Paolo.
- Support for SMR zones for deadline and mq-deadline from Damien and
Christoph.
- Set of fixes for bcache by way of Michael Lyle, including fixes
from himself, Kent, Rui, Tang, and Coly.
- Series from Matias for lightnvm with fixes from Hans Holmberg,
Javier, and Matias. Mostly centered around pblk, and the removing
rrpc 1.2 in preparation for supporting 2.0.
- A couple of NVMe pull requests from Christoph. Nothing major in
here, just fixes and cleanups, and support for command tracing from
Johannes.
- Support for blk-throttle for tracking reads and writes separately.
From Joseph Qi. A few cleanups/fixes also for blk-throttle from
Weiping.
- Series from Mike Snitzer that enables dm to register its queue more
logically, something that's alwways been problematic on dm since
it's a stacked device.
- Series from Ming cleaning up some of the bio accessor use, in
preparation for supporting multipage bvecs.
- Various fixes from Ming closing up holes around queue mapping and
quiescing.
- BSD partition fix from Richard Narron, fixing a problem where we
can't mount newer (10/11) FreeBSD partitions.
- Series from Tejun reworking blk-mq timeout handling. The previous
scheme relied on atomic bits, but it had races where we would think
a request had timed out if it to reused at the wrong time.
- null_blk now supports faking timeouts, to enable us to better
exercise and test that functionality separately. From me.
- Kill the separate atomic poll bit in the request struct. After
this, we don't use the atomic bits on blk-mq anymore at all. From
me.
- sgl_alloc/free helpers from Bart.
- Heavily contended tag case scalability improvement from me.
- Various little fixes and cleanups from Arnd, Bart, Corentin,
Douglas, Eryu, Goldwyn, and myself"
* 'for-4.16/block' of git://git.kernel.dk/linux-block: (186 commits)
block: remove smart1,2.h
nvme: add tracepoint for nvme_complete_rq
nvme: add tracepoint for nvme_setup_cmd
nvme-pci: introduce RECONNECTING state to mark initializing procedure
nvme-rdma: remove redundant boolean for inline_data
nvme: don't free uuid pointer before printing it
nvme-pci: Suspend queues after deleting them
bsg: use pr_debug instead of hand crafted macros
blk-mq-debugfs: don't allow write on attributes with seq_operations set
nvme-pci: Fix queue double allocations
block: Set BIO_TRACE_COMPLETION on new bio during split
blk-throttle: use queue_is_rq_based
block: Remove kblockd_schedule_delayed_work{,_on}()
blk-mq: Avoid that blk_mq_delay_run_hw_queue() introduces unintended delays
blk-mq: Rename blk_mq_request_direct_issue() into blk_mq_request_issue_directly()
lib/scatterlist: Fix chaining support in sgl_alloc_order()
blk-throttle: track read and write request individually
block: add bdev_read_only() checks to common helpers
block: fail op_is_write() requests to read-only partitions
blk-throttle: export io_serviced_recursive, io_service_bytes_recursive
...
Fix to return error code -ENOMEM from the mempool_create_kmalloc_pool()
error handling case instead of 0, as done elsewhere in this function.
Fixes: ef43aa3806 ("dm crypt: add cryptographic data integrity protection (authenticated encryption)")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Loading key via kernel keyring service erases the internal
key copy immediately after we pass it in crypto layer. This is
wrong because IV is initialized later and we use wrong key
for the initialization (instead of real key there's just zeroed
block).
The bug may cause data corruption if key is loaded via kernel keyring
service first and later same crypt device is reactivated using exactly
same key in hexbyte representation, or vice versa. The bug (and fix)
affects only ciphers using following IVs: essiv, lmk and tcw.
Fixes: c538f6ec9f ("dm crypt: add ability to use keys from the kernel key retention service")
Cc: stable@vger.kernel.org # 4.10+
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Reviewed-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If dm-crypt uses authenticated mode with separate MAC, there are two
concatenated part of the key structure - key(s) for encryption and
authentication key.
Add a missing check for authenticated key length. If this key length is
smaller than actually provided key, dm-crypt now properly fails instead
of crashing.
Fixes: ef43aa3806 ("dm crypt: add cryptographic data integrity protection (authenticated encryption)")
Cc: stable@vger.kernel.org # 4.12+
Reported-by: Salah Coronya <salahx@yahoo.com>
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The bio is always freed after running crypt_free_buffer_pages(), so it
isn't necessary to clear bv->bv_page.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc:dm-devel@redhat.com
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The BIOSET_NEED_RESCUER flag is only needed when a make_request_fn might
do two allocations from the one bioset, and the second one could block
until the first bio completes.
dm-crypt does allocate from this bioset inside the dm make_request_fn,
but does so using GFP_NOWAIT so that the allocation will not block.
So BIOSET_NEED_RESCUER is not needed.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When slub_debug is enabled kmalloc returns unaligned memory. XFS uses
this unaligned memory for its buffers (if an unaligned buffer crosses a
page, XFS frees it and allocates a full page instead - see the function
xfs_buf_allocate_memory).
dm-crypt checks if bv_offset is aligned on page size and these checks
fail with slub_debug and XFS.
Fix this bug by removing the bv_offset checks. Switch to checking if
bv_len is aligned instead of bv_offset (this check should be sufficient
to prevent overruns if a bio with too small bv_len is received).
Fixes: 8f0009a225 ("dm crypt: optionally support larger encryption sector size")
Cc: stable@vger.kernel.org # v4.12+
Reported-by: Bruno Prémont <bonbons@sysophe.eu>
Tested-by: Bruno Prémont <bonbons@sysophe.eu>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If a crypt mapping uses optional sector_size feature, additional
restrictions to mapped device segment size must be applied in
constructor, otherwise the device activation will fail later.
Fixes: 8f0009a225 ("dm crypt: optionally support larger encryption sector size")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fix memory leak of cipher_api.
Fixes: 33d2f09fcb (dm crypt: introduce new format of cipher with "capi:" prefix)
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- Constify a few variables in DM core and DM integrity
- Add bufio optimization and checksum failure accounting to DM integrity
- Fix DM integrity to avoid checking integrity of failed reads
- Fix DM integrity to use init_completion
- A couple DM log-writes target fixes
- Simplify DAX flushing by eliminating the unnecessary flush abstraction
that was stood up for DM's use.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZuo8UAAoJEMUj8QotnQNa5BEIANO4mHh1nrzEbH72a4RCLgxV
H1Pk1zZx/W1bhOOmcRRhxCSM85dPgsCegc5EmpwLZEMavQrP9UZblHcYOUsyIx7W
S/lWa+soOq/5N2OveROc4WdoWVs50UFmc1+BcClc4YrEe+15XC3R0VMkjX2b/hUL
o2eYhPjpMlgaorMtRRU6MAooo2fBRQ9m05aPeVgd35fxibrE7PZm+EYW09wa0STi
9ufuDXJf8+TtFP/38BD41LbUEskuHUZTSDeAJ+3DBaTtfEZcZYxsst4P9JangsHx
jqqqI9aYzFD2a27fl9WLhCvm40YFiKp5nwzED0RZjzWxVa/jTShX7a49BdzTTfw=
=rkSB
-----END PGP SIGNATURE-----
Merge tag 'for-4.14/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Some request-based DM core and DM multipath fixes and cleanups
- Constify a few variables in DM core and DM integrity
- Add bufio optimization and checksum failure accounting to DM
integrity
- Fix DM integrity to avoid checking integrity of failed reads
- Fix DM integrity to use init_completion
- A couple DM log-writes target fixes
- Simplify DAX flushing by eliminating the unnecessary flush
abstraction that was stood up for DM's use.
* tag 'for-4.14/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dax: remove the pmem_dax_ops->flush abstraction
dm integrity: use init_completion instead of COMPLETION_INITIALIZER_ONSTACK
dm integrity: make blk_integrity_profile structure const
dm integrity: do not check integrity for failed read operations
dm log writes: fix >512b sectorsize support
dm log writes: don't use all the cpu while waiting to log blocks
dm ioctl: constify ioctl lookup table
dm: constify argument arrays
dm integrity: count and display checksum failures
dm integrity: optimize writing dm-bufio buffers that are partially changed
dm rq: do not update rq partially in each ending bio
dm rq: make dm-sq requeuing behavior consistent with dm-mq behavior
dm mpath: complain about unsupported __multipath_map_bio() return values
dm mpath: avoid that building with W=1 causes gcc 7 to complain about fall-through
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
The arrays of 'struct dm_arg' are never modified by the device-mapper
core, so constify them so that they are placed in .rodata.
(Exception: the args array in dm-raid cannot be constified because it is
allocated on the stack and modified.)
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This flag is never set right after calling bio_integrity_alloc,
so don't clear it and confuse the reader.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There are quite a number of occurrences in the kernel of the pattern
if (dst != src)
memcpy(dst, src, walk.total % AES_BLOCK_SIZE);
crypto_xor(dst, final, walk.total % AES_BLOCK_SIZE);
or
crypto_xor(keystream, src, nbytes);
memcpy(dst, keystream, nbytes);
where crypto_xor() is preceded or followed by a memcpy() invocation
that is only there because crypto_xor() uses its output parameter as
one of the inputs. To avoid having to add new instances of this pattern
in the arm64 code, which will be refactored to implement non-SIMD
fallbacks, add an alternative implementation called crypto_xor_cpy(),
taking separate input and output arguments. This removes the need for
the separate memcpy().
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The big-endian IV (plain64be) is needed to map images from extracted
disks that are used in some external (on-chip FDE) disk encryption
drives, e.g.: data recovery from external USB/SATA drives that support
"internal" encryption.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This patch converts bioset_create() to not create a workqueue by
default, so alloctions will never trigger punt_bios_to_rescuer(). It
also introduces a new flag BIOSET_NEED_RESCUER which tells
bioset_create() to preserve the old behavior.
All callers of bioset_create() that are inside block device drivers,
are given the BIOSET_NEED_RESCUER flag.
biosets used by filesystems or other top-level users do not
need rescuing as the bio can never be queued behind other
bios. This includes fs_bio_set, blkdev_dio_pool,
btrfs_bioset, xfs_ioend_bioset, and one allocated by
target_core_iblock.c.
biosets used by md/raid do not need rescuing as
their usage was recently audited and revised to never
risk deadlock.
It is hoped that most, if not all, of the remaining biosets
can end up being the non-rescued version.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Credit-to: Ming Lei <ming.lei@redhat.com> (minor fixes)
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
"flags" arguments are often seen as good API design as they allow
easy extensibility.
bioset_create_nobvec() is implemented internally as a variation in
flags passed to __bioset_create().
To support future extension, make the internal structure part of the
API.
i.e. add a 'flags' argument to bioset_create() and discard
bioset_create_nobvec().
Note that the bio_split allocations in drivers/md/raid* do not need
the bvec mempool - they should have used bioset_create_nobvec().
Suggested-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace bi_error with a new bi_status to allow for a clear conversion.
Note that device mapper overloaded bi_error with a private value, which
we'll have to keep arround at least for now and thus propagate to a
proper blk_status_t value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead use the special DM_MAPIO_KILL return value to return -EIO just
like we do for the request based path. Note that dm-log-writes returned
-ENOMEM in a few places, which now becomes -EIO instead. No consumer
treats -ENOMEM special so this shouldn't be an issue (and it should
use a mempool to start with to make guaranteed progress).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
whether blocks should migrate to/from the cache. The bio-prison-v2
interface supports this improvement by enabling direct dispatch of
work to workqueues rather than having to delay the actual work
dispatch to the DM cache core. So the dm-cache policies are much more
nimble by being able to drive IO as they see fit. One immediate
benefit from the improved latency is a cache that should be much more
adaptive to changing workloads.
- Add a new DM integrity target that emulates a block device that has
additional per-sector tags that can be used for storing integrity
information.
- Add a new authenticated encryption feature to the DM crypt target that
builds on the capabilities provided by the DM integrity target.
- Add MD interface for switching the raid4/5/6 journal mode and update
the DM raid target to use it to enable aid4/5/6 journal write-back
support.
- Switch the DM verity target over to using the asynchronous hash crypto
API (this helps work better with architectures that have access to
off-CPU algorithm providers, which should reduce CPU utilization).
- Various request-based DM and DM multipath fixes and improvements from
Bart and Christoph.
- A DM thinp target fix for a bio structure leak that occurs for each
discard IFF discard passdown is enabled.
- A fix for a possible deadlock in DM bufio and a fix to re-check the
new buffer allocation watermark in the face of competing admin changes
to the 'max_cache_size_bytes' tunable.
- A couple DM core cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZB6vtAAoJEMUj8QotnQNaoicIALuZTLElgAzxzA28cfk1+1Ea
Gd09CfJ3M6cvk/YGUU7WwiSYIwu16yOJALG4sLcYnEmUCzvKfFPcl/RpeSJHPpYM
0aVXa6NIJw7K2r3C17toiK2DRMHYw6QU843WeWI93vBW13lDJklNJL9fM7GBEOLH
NMSNw2mAq9ajtLlnJhM3ZfhloA7/u/jektvlBO1AA3RQ5Kx1cXVXFPqN7FdRfcqp
4RuEMe9faAadlXLsj3bia5IBmF/W0Qza6JilP+NLKLWB4fm7LZDjN/k+TsHWMa9e
cGR73TgUGLMBJX+sDJy8R3oeBG9JZkFVkD7I30eCjzyhSOs/54XNYQ23EkqHJU0=
=9Ryi
-----END PGP SIGNATURE-----
Merge tag 'for-4.12/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- A major update for DM cache that reduces the latency for deciding
whether blocks should migrate to/from the cache. The bio-prison-v2
interface supports this improvement by enabling direct dispatch of
work to workqueues rather than having to delay the actual work
dispatch to the DM cache core. So the dm-cache policies are much more
nimble by being able to drive IO as they see fit. One immediate
benefit from the improved latency is a cache that should be much more
adaptive to changing workloads.
- Add a new DM integrity target that emulates a block device that has
additional per-sector tags that can be used for storing integrity
information.
- Add a new authenticated encryption feature to the DM crypt target
that builds on the capabilities provided by the DM integrity target.
- Add MD interface for switching the raid4/5/6 journal mode and update
the DM raid target to use it to enable aid4/5/6 journal write-back
support.
- Switch the DM verity target over to using the asynchronous hash
crypto API (this helps work better with architectures that have
access to off-CPU algorithm providers, which should reduce CPU
utilization).
- Various request-based DM and DM multipath fixes and improvements from
Bart and Christoph.
- A DM thinp target fix for a bio structure leak that occurs for each
discard IFF discard passdown is enabled.
- A fix for a possible deadlock in DM bufio and a fix to re-check the
new buffer allocation watermark in the face of competing admin
changes to the 'max_cache_size_bytes' tunable.
- A couple DM core cleanups.
* tag 'for-4.12/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (50 commits)
dm bufio: check new buffer allocation watermark every 30 seconds
dm bufio: avoid a possible ABBA deadlock
dm mpath: make it easier to detect unintended I/O request flushes
dm mpath: cleanup QUEUE_IF_NO_PATH bit manipulation by introducing assign_bit()
dm mpath: micro-optimize the hot path relative to MPATHF_QUEUE_IF_NO_PATH
dm: introduce enum dm_queue_mode to cleanup related code
dm mpath: verify __pg_init_all_paths locking assumptions at runtime
dm: verify suspend_locking assumptions at runtime
dm block manager: remove an unused argument from dm_block_manager_create()
dm rq: check blk_mq_register_dev() return value in dm_mq_init_request_queue()
dm mpath: delay requeuing while path initialization is in progress
dm mpath: avoid that path removal can trigger an infinite loop
dm mpath: split and rename activate_path() to prepare for its expanded use
dm ioctl: prevent stack leak in dm ioctl call
dm integrity: use previously calculated log2 of sectors_per_block
dm integrity: use hex2bin instead of open-coded variant
dm crypt: replace custom implementation of hex2bin()
dm crypt: remove obsolete references to per-CPU state
dm verity: switch to using asynchronous hash crypto API
dm crypt: use WQ_HIGHPRI for the IO and crypt workqueues
...
There is no need to have a duplication of the generic library, i.e. hex2bin().
Replace the open coded variant.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm-crypt used to use separate crypto transforms for each CPU, but this
is no longer the case. To avoid confusion, fix up obsolete comments and
rename setup_essiv_cpu().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Running dm-crypt with workqueues at the standard priority results in IO
competing for CPU time with standard user apps, which can lead to
pipeline bubbles and seriously degraded performance. Move to using
WQ_HIGHPRI workqueues to protect against that.
Signed-off-by: Tim Murray <timmurray@google.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The message "key wipe" used to wipe real key stored in crypto layer by
rewriting it with zeroes. Since commit 28856a9 ("crypto: xts -
consolidate sanity check for keys") this no longer works in FIPS mode
for XTS.
While running in FIPS mode the crypto key part has to differ from the
tweak key.
Fixes: 28856a9 ("crypto: xts - consolidate sanity check for keys")
Cc: stable@vger.kernel.org
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Previously, dm-crypt could use blocks composed of multiple 512b sectors
but it created integrity profile for each 512b sector (it padded it with
zeroes). Fix dm-crypt so that the integrity profile is sent for each
block not each sector.
The user must use the same block size in the DM crypt and integrity
targets.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Now that we use the proper REQ_OP_WRITE_ZEROES operation everywhere we can
kill this hack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
sector_div is very slow, so we introduce a variable sector_shift and
use shift instead of sector_div.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add optional "sector_size" parameter that specifies encryption sector
size (atomic unit of block device encryption).
Parameter can be in range 512 - 4096 bytes and must be power of two.
For compatibility reasons, the maximal IO must fit into the page limit,
so the limit is set to the minimal page size possible (4096 bytes).
NOTE: this device cannot yet be handled by cryptsetup if this parameter
is set.
IV for the sector is calculated from the 512 bytes sector offset unless
the iv_large_sectors option is used.
Test script using dmsetup:
DEV="/dev/sdb"
DEV_SIZE=$(blockdev --getsz $DEV)
KEY="9c1185a5c5e9fc54612808977ee8f548b2258d31ddadef707ba62c166051b9e3cd0294c27515f2bccee924e8823ca6e124b8fc3167ed478bca702babe4e130ac"
BLOCK_SIZE=4096
# dmsetup create test_crypt --table "0 $DEV_SIZE crypt aes-xts-plain64 $KEY 0 $DEV 0 1 sector_size:$BLOCK_SIZE"
# dmsetup table --showkeys test_crypt
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
For the new authenticated encryption we have to support generic composed
modes (combination of encryption algorithm and authenticator) because
this is how the kernel crypto API accesses such algorithms.
To simplify the interface, we accept an algorithm directly in crypto API
format. The new format is recognised by the "capi:" prefix. The
dmcrypt internal IV specification is the same as for the old format.
The crypto API cipher specifications format is:
capi:cipher_api_spec-ivmode[:ivopts]
Examples:
capi:cbc(aes)-essiv:sha256 (equivalent to old aes-cbc-essiv:sha256)
capi:xts(aes)-plain64 (equivalent to old aes-xts-plain64)
Examples of authenticated modes:
capi:gcm(aes)-random
capi:authenc(hmac(sha256),xts(aes))-random
capi:rfc7539(chacha20,poly1305)-random
Authenticated modes can only be configured using the new cipher format.
Note that this format allows user to specify arbitrary combinations that
can be insecure. (Policy decision is done in cryptsetup userspace.)
Authenticated encryption algorithms can be of two types, either native
modes (like GCM) that performs both encryption and authentication
internally, or composed modes where user can compose AEAD with separate
specification of encryption algorithm and authenticator.
For composed mode with HMAC (length-preserving encryption mode like an
XTS and HMAC as an authenticator) we have to calculate HMAC digest size
(the separate authentication key is the same size as the HMAC digest).
Introduce crypt_ctr_auth_cipher() to parse the crypto API string to get
HMAC algorithm and retrieve digest size from it.
Also, for HMAC composed mode we need to parse the crypto API string to
get the cipher mode nested in the specification. For native AEAD mode
(like GCM), we can use crypto_tfm_alg_name() API to get the cipher
specification.
Because the HMAC composed mode is not processed the same as the native
AEAD mode, the CRYPT_MODE_INTEGRITY_HMAC flag is no longer needed and
"hmac" specification for the table integrity argument is removed.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Allow the use of per-sector metadata, provided by the dm-integrity
module, for integrity protection and persistently stored per-sector
Initialization Vector (IV). The underlying device must support the
"DM-DIF-EXT-TAG" dm-integrity profile.
The per-bio integrity metadata is allocated by dm-crypt for every bio.
Example of low-level mapping table for various types of use:
DEV=/dev/sdb
SIZE=417792
# Additional HMAC with CBC-ESSIV, key is concatenated encryption key + HMAC key
SIZE_INT=389952
dmsetup create x --table "0 $SIZE_INT integrity $DEV 0 32 J 0"
dmsetup create y --table "0 $SIZE_INT crypt aes-cbc-essiv:sha256 \
11ff33c6fb942655efb3e30cf4c0fd95f5ef483afca72166c530ae26151dd83b \
00112233445566778899aabbccddeeff00112233445566778899aabbccddeeff \
0 /dev/mapper/x 0 1 integrity:32:hmac(sha256)"
# AEAD (Authenticated Encryption with Additional Data) - GCM with random IVs
# GCM in kernel uses 96bits IV and we store 128bits auth tag (so 28 bytes metadata space)
SIZE_INT=393024
dmsetup create x --table "0 $SIZE_INT integrity $DEV 0 28 J 0"
dmsetup create y --table "0 $SIZE_INT crypt aes-gcm-random \
11ff33c6fb942655efb3e30cf4c0fd95f5ef483afca72166c530ae26151dd83b \
0 /dev/mapper/x 0 1 integrity:28:aead"
# Random IV only for XTS mode (no integrity protection but provides atomic random sector change)
SIZE_INT=401272
dmsetup create x --table "0 $SIZE_INT integrity $DEV 0 16 J 0"
dmsetup create y --table "0 $SIZE_INT crypt aes-xts-random \
11ff33c6fb942655efb3e30cf4c0fd95f5ef483afca72166c530ae26151dd83b \
0 /dev/mapper/x 0 1 integrity:16:none"
# Random IV with XTS + HMAC integrity protection
SIZE_INT=377656
dmsetup create x --table "0 $SIZE_INT integrity $DEV 0 48 J 0"
dmsetup create y --table "0 $SIZE_INT crypt aes-xts-random \
11ff33c6fb942655efb3e30cf4c0fd95f5ef483afca72166c530ae26151dd83b \
00112233445566778899aabbccddeeff00112233445566778899aabbccddeeff \
0 /dev/mapper/x 0 1 integrity:48:hmac(sha256)"
Both AEAD and HMAC protection authenticates not only data but also
sector metadata.
HMAC protection is implemented through autenc wrapper (so it is
processed the same way as an authenticated mode).
In HMAC mode there are two keys (concatenated in dm-crypt mapping
table). First is the encryption key and the second is the key for
authentication (HMAC). (It is userspace decision if these keys are
independent or somehow derived.)
The sector request for AEAD/HMAC authenticated encryption looks like this:
|----- AAD -------|------ DATA -------|-- AUTH TAG --|
| (authenticated) | (auth+encryption) | |
| sector_LE | IV | sector in/out | tag in/out |
For writes, the integrity fields are calculated during AEAD encryption
of every sector and stored in bio integrity fields and sent to
underlying dm-integrity target for storage.
For reads, the integrity metadata is verified during AEAD decryption of
every sector (they are filled in by dm-integrity, but the integrity
fields are pre-allocated in dm-crypt).
There is also an experimental support in cryptsetup utility for more
friendly configuration (part of LUKS2 format).
Because the integrity fields are not valid on initial creation, the
device must be "formatted". This can be done by direct-io writes to the
device (e.g. dd in direct-io mode). For now, there is available trivial
tool to do this, see: https://github.com/mbroz/dm_int_tools
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Ondrej Mosnacek <omosnacek@gmail.com>
Signed-off-by: Vashek Matyas <matyas@fi.muni.cz>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
rcu_dereference_key() and user_key_payload() are currently being used in
two different, incompatible ways:
(1) As a wrapper to rcu_dereference() - when only the RCU read lock used
to protect the key.
(2) As a wrapper to rcu_dereference_protected() - when the key semaphor is
used to protect the key and the may be being modified.
Fix this by splitting both of the key wrappers to produce:
(1) RCU accessors for keys when caller has the key semaphore locked:
dereference_key_locked()
user_key_payload_locked()
(2) RCU accessors for keys when caller holds the RCU read lock:
dereference_key_rcu()
user_key_payload_rcu()
This should fix following warning in the NFS idmapper
===============================
[ INFO: suspicious RCU usage. ]
4.10.0 #1 Tainted: G W
-------------------------------
./include/keys/user-type.h:53 suspicious rcu_dereference_protected() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 0
1 lock held by mount.nfs/5987:
#0: (rcu_read_lock){......}, at: [<d000000002527abc>] nfs_idmap_get_key+0x15c/0x420 [nfsv4]
stack backtrace:
CPU: 1 PID: 5987 Comm: mount.nfs Tainted: G W 4.10.0 #1
Call Trace:
dump_stack+0xe8/0x154 (unreliable)
lockdep_rcu_suspicious+0x140/0x190
nfs_idmap_get_key+0x380/0x420 [nfsv4]
nfs_map_name_to_uid+0x2a0/0x3b0 [nfsv4]
decode_getfattr_attrs+0xfac/0x16b0 [nfsv4]
decode_getfattr_generic.constprop.106+0xbc/0x150 [nfsv4]
nfs4_xdr_dec_lookup_root+0xac/0xb0 [nfsv4]
rpcauth_unwrap_resp+0xe8/0x140 [sunrpc]
call_decode+0x29c/0x910 [sunrpc]
__rpc_execute+0x140/0x8f0 [sunrpc]
rpc_run_task+0x170/0x200 [sunrpc]
nfs4_call_sync_sequence+0x68/0xa0 [nfsv4]
_nfs4_lookup_root.isra.44+0xd0/0xf0 [nfsv4]
nfs4_lookup_root+0xe0/0x350 [nfsv4]
nfs4_lookup_root_sec+0x70/0xa0 [nfsv4]
nfs4_find_root_sec+0xc4/0x100 [nfsv4]
nfs4_proc_get_rootfh+0x5c/0xf0 [nfsv4]
nfs4_get_rootfh+0x6c/0x190 [nfsv4]
nfs4_server_common_setup+0xc4/0x260 [nfsv4]
nfs4_create_server+0x278/0x3c0 [nfsv4]
nfs4_remote_mount+0x50/0xb0 [nfsv4]
mount_fs+0x74/0x210
vfs_kern_mount+0x78/0x220
nfs_do_root_mount+0xb0/0x140 [nfsv4]
nfs4_try_mount+0x60/0x100 [nfsv4]
nfs_fs_mount+0x5ec/0xda0 [nfs]
mount_fs+0x74/0x210
vfs_kern_mount+0x78/0x220
do_mount+0x254/0xf70
SyS_mount+0x94/0x100
system_call+0x38/0xe0
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Implement wraparound-safe refcount_t and kref_t types based on
generic atomic primitives (Peter Zijlstra)
- Improve and fix the ww_mutex code (Nicolai Hähnle)
- Add self-tests to the ww_mutex code (Chris Wilson)
- Optimize percpu-rwsems with the 'rcuwait' mechanism (Davidlohr
Bueso)
- Micro-optimize the current-task logic all around the core kernel
(Davidlohr Bueso)
- Tidy up after recent optimizations: remove stale code and APIs,
clean up the code (Waiman Long)
- ... plus misc fixes, updates and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
fork: Fix task_struct alignment
locking/spinlock/debug: Remove spinlock lockup detection code
lockdep: Fix incorrect condition to print bug msgs for MAX_LOCKDEP_CHAIN_HLOCKS
lkdtm: Convert to refcount_t testing
kref: Implement 'struct kref' using refcount_t
refcount_t: Introduce a special purpose refcount type
sched/wake_q: Clarify queue reinit comment
sched/wait, rcuwait: Fix typo in comment
locking/mutex: Fix lockdep_assert_held() fail
locking/rtmutex: Flip unlikely() branch to likely() in __rt_mutex_slowlock()
locking/rwsem: Reinit wake_q after use
locking/rwsem: Remove unnecessary atomic_long_t casts
jump_labels: Move header guard #endif down where it belongs
locking/atomic, kref: Implement kref_put_lock()
locking/ww_mutex: Turn off __must_check for now
locking/atomic, kref: Avoid more abuse
locking/atomic, kref: Use kref_get_unless_zero() more
locking/atomic, kref: Kill kref_sub()
locking/atomic, kref: Add kref_read()
locking/atomic, kref: Add KREF_INIT()
...
The lockdep splat below hints at a bug in RCU usage in dm-crypt that
was introduced with commit c538f6ec9f ("dm crypt: add ability to use
keys from the kernel key retention service"). The kernel keyring
function user_key_payload() is in fact a wrapper for
rcu_dereference_protected() which must not be called with only
rcu_read_lock() section mark.
Unfortunately the kernel keyring subsystem doesn't currently provide
an interface that allows the use of an RCU read-side section. So for
now we must drop RCU in favour of rwsem until a proper function is
made available in the kernel keyring subsystem.
===============================
[ INFO: suspicious RCU usage. ]
4.10.0-rc5 #2 Not tainted
-------------------------------
./include/keys/user-type.h:53 suspicious rcu_dereference_protected() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
2 locks held by cryptsetup/6464:
#0: (&md->type_lock){+.+.+.}, at: [<ffffffffa02472a2>] dm_lock_md_type+0x12/0x20 [dm_mod]
#1: (rcu_read_lock){......}, at: [<ffffffffa02822f8>] crypt_set_key+0x1d8/0x4b0 [dm_crypt]
stack backtrace:
CPU: 1 PID: 6464 Comm: cryptsetup Not tainted 4.10.0-rc5 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.1-1.fc24 04/01/2014
Call Trace:
dump_stack+0x67/0x92
lockdep_rcu_suspicious+0xc5/0x100
crypt_set_key+0x351/0x4b0 [dm_crypt]
? crypt_set_key+0x1d8/0x4b0 [dm_crypt]
crypt_ctr+0x341/0xa53 [dm_crypt]
dm_table_add_target+0x147/0x330 [dm_mod]
table_load+0x111/0x350 [dm_mod]
? retrieve_status+0x1c0/0x1c0 [dm_mod]
ctl_ioctl+0x1f5/0x510 [dm_mod]
dm_ctl_ioctl+0xe/0x20 [dm_mod]
do_vfs_ioctl+0x8e/0x690
? ____fput+0x9/0x10
? task_work_run+0x7e/0xa0
? trace_hardirqs_on_caller+0x122/0x1b0
SyS_ioctl+0x3c/0x70
entry_SYSCALL_64_fastpath+0x18/0xad
RIP: 0033:0x7f392c9a4ec7
RSP: 002b:00007ffef6383378 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007ffef63830a0 RCX: 00007f392c9a4ec7
RDX: 000000000124fcc0 RSI: 00000000c138fd09 RDI: 0000000000000005
RBP: 00007ffef6383090 R08: 00000000ffffffff R09: 00000000012482b0
R10: 2a28205d34383336 R11: 0000000000000246 R12: 00007f392d803a08
R13: 00007ffef63831e0 R14: 0000000000000000 R15: 00007f392d803a0b
Fixes: c538f6ec9f ("dm crypt: add ability to use keys from the kernel key retention service")
Reported-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This is a nasty interface and setting the state of a foreign task must
not be done. As of the following commit:
be628be095 ("bcache: Make gc wakeup sane, remove set_task_state()")
... everyone in the kernel calls set_task_state() with current, allowing
the helper to be removed.
However, as the comment indicates, it is still around for those archs
where computing current is more expensive than using a pointer, at least
in theory. An important arch that is affected is arm64, however this has
been addressed now [1] and performance is up to par making no difference
with either calls.
Of all the callers, if any, it's the locking bits that would care most
about this -- ie: we end up passing a tsk pointer to a lot of the lock
slowpath, and setting ->state on that. The following numbers are based
on two tests: a custom ad-hoc microbenchmark that just measures
latencies (for ~65 million calls) between get_task_state() vs
get_current_state().
Secondly for a higher overview, an unlink microbenchmark was used,
which pounds on a single file with open, close,unlink combos with
increasing thread counts (up to 4x ncpus). While the workload is quite
unrealistic, it does contend a lot on the inode mutex or now rwsem.
[1] https://lkml.kernel.org/r/1483468021-8237-1-git-send-email-mark.rutland@arm.com
== 1. x86-64 ==
Avg runtime set_task_state(): 601 msecs
Avg runtime set_current_state(): 552 msecs
vanilla dirty
Hmean unlink1-processes-2 36089.26 ( 0.00%) 38977.33 ( 8.00%)
Hmean unlink1-processes-5 28555.01 ( 0.00%) 29832.55 ( 4.28%)
Hmean unlink1-processes-8 37323.75 ( 0.00%) 44974.57 ( 20.50%)
Hmean unlink1-processes-12 43571.88 ( 0.00%) 44283.01 ( 1.63%)
Hmean unlink1-processes-21 34431.52 ( 0.00%) 38284.45 ( 11.19%)
Hmean unlink1-processes-30 34813.26 ( 0.00%) 37975.17 ( 9.08%)
Hmean unlink1-processes-48 37048.90 ( 0.00%) 39862.78 ( 7.59%)
Hmean unlink1-processes-79 35630.01 ( 0.00%) 36855.30 ( 3.44%)
Hmean unlink1-processes-110 36115.85 ( 0.00%) 39843.91 ( 10.32%)
Hmean unlink1-processes-141 32546.96 ( 0.00%) 35418.52 ( 8.82%)
Hmean unlink1-processes-172 34674.79 ( 0.00%) 36899.21 ( 6.42%)
Hmean unlink1-processes-203 37303.11 ( 0.00%) 36393.04 ( -2.44%)
Hmean unlink1-processes-224 35712.13 ( 0.00%) 36685.96 ( 2.73%)
== 2. ppc64le ==
Avg runtime set_task_state(): 938 msecs
Avg runtime set_current_state: 940 msecs
vanilla dirty
Hmean unlink1-processes-2 19269.19 ( 0.00%) 30704.50 ( 59.35%)
Hmean unlink1-processes-5 20106.15 ( 0.00%) 21804.15 ( 8.45%)
Hmean unlink1-processes-8 17496.97 ( 0.00%) 17243.28 ( -1.45%)
Hmean unlink1-processes-12 14224.15 ( 0.00%) 17240.21 ( 21.20%)
Hmean unlink1-processes-21 14155.66 ( 0.00%) 15681.23 ( 10.78%)
Hmean unlink1-processes-30 14450.70 ( 0.00%) 15995.83 ( 10.69%)
Hmean unlink1-processes-48 16945.57 ( 0.00%) 16370.42 ( -3.39%)
Hmean unlink1-processes-79 15788.39 ( 0.00%) 14639.27 ( -7.28%)
Hmean unlink1-processes-110 14268.48 ( 0.00%) 14377.40 ( 0.76%)
Hmean unlink1-processes-141 14023.65 ( 0.00%) 16271.69 ( 16.03%)
Hmean unlink1-processes-172 13417.62 ( 0.00%) 16067.55 ( 19.75%)
Hmean unlink1-processes-203 15293.08 ( 0.00%) 15440.40 ( 0.96%)
Hmean unlink1-processes-234 13719.32 ( 0.00%) 16190.74 ( 18.01%)
Hmean unlink1-processes-265 16400.97 ( 0.00%) 16115.22 ( -1.74%)
Hmean unlink1-processes-296 14388.60 ( 0.00%) 16216.13 ( 12.70%)
Hmean unlink1-processes-320 15771.85 ( 0.00%) 15905.96 ( 0.85%)
x86-64 (known to be fast for get_current()/this_cpu_read_stable() caching)
and ppc64 (with paca) show similar improvements in the unlink microbenches.
The small delta for ppc64 (2ms), does not represent the gains on the unlink
runs. In the case of x86, there was a decent amount of variation in the
latency runs, but always within a 20 to 50ms increase), ppc was more constant.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dave@stgolabs.net
Cc: mark.rutland@arm.com
Link: http://lkml.kernel.org/r/1483479794-14013-5-git-send-email-dave@stgolabs.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
. some locking improvements in DM bufio
. add Kconfig option to disable the DM block manager's extra locking
which mainly serves as a developer tool
. a few bug fixes to DM's persistent-data
. a couple changes to prepare for multipage biovec support in the block
layer
. various improvements and cleanups in the DM core, DM cache, DM raid
and DM crypt
. add ability to have DM crypt use keys from the kernel key retention
service
. add a new "error_writes" feature to the DM flakey target, reads are
left unchanged in this mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYUW8zAAoJEMUj8QotnQNaAWEIAMRQ4aCXq5T7F9Hf4K/l6FwO
FoBr2TPS3Lf0vm/A5Tr819I47hk7q0oroa61ARbpS90iuGt/Au/Sk35cn1BwT0YW
llMvMGbh+w9ZBUJGkyexdXbyfm5ywPHuthMr4CK/UNASyjDl2QMAeBuUZ6FLSPn1
RUL/RYv0mG/7EXOPz0PURPb5rpjO15cAU0NjfNS0862UVR8x8dNS6iImOmScsioe
Flw90qPl3kMBxBHik8xSPJfhtW+lD7xSaOlWzHKtalnUZHRG2BNUtlAMKdiaynx2
yl9MhSsi8wlgd4h9WmlmaOr0VqkU5UYY9D9TDuuJwXnHUXGenVSJ/aGOohr+bm4=
=kOoK
-----END PGP SIGNATURE-----
Merge tag 'dm-4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- various fixes and improvements to request-based DM and DM multipath
- some locking improvements in DM bufio
- add Kconfig option to disable the DM block manager's extra locking
which mainly serves as a developer tool
- a few bug fixes to DM's persistent-data
- a couple changes to prepare for multipage biovec support in the block
layer
- various improvements and cleanups in the DM core, DM cache, DM raid
and DM crypt
- add ability to have DM crypt use keys from the kernel key retention
service
- add a new "error_writes" feature to the DM flakey target, reads are
left unchanged in this mode
* tag 'dm-4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (40 commits)
dm flakey: introduce "error_writes" feature
dm cache policy smq: use hash_32() instead of hash_32_generic()
dm crypt: reject key strings containing whitespace chars
dm space map: always set ev if sm_ll_mutate() succeeds
dm space map metadata: skip useless memcpy in metadata_ll_init_index()
dm space map metadata: fix 'struct sm_metadata' leak on failed create
Documentation: dm raid: define data_offset status field
dm raid: fix discard support regression
dm raid: don't allow "write behind" with raid4/5/6
dm mpath: use hw_handler_params if attached hw_handler is same as requested
dm crypt: add ability to use keys from the kernel key retention service
dm array: remove a dead assignment in populate_ablock_with_values()
dm ioctl: use offsetof() instead of open-coding it
dm rq: simplify use_blk_mq initialization
dm: use blk_set_queue_dying() in __dm_destroy()
dm bufio: drop the lock when doing GFP_NOIO allocation
dm bufio: don't take the lock in dm_bufio_shrink_count
dm bufio: avoid sleeping while holding the dm_bufio lock
dm table: simplify dm_table_determine_type()
dm table: an 'all_blk_mq' table must be loaded for a blk-mq DM device
...
Unfortunately key_string may theoretically contain whitespace even after
it's processed by dm_split_args(). The reason for this is DM core
supports escaping of almost all chars including any whitespace.
If userspace passes a key to the kernel in format ":32:logon:my_prefix:my\ key"
dm-crypt will look up key "my_prefix:my key" in kernel keyring service.
So far everything's fine.
Unfortunately if userspace later calls DM_TABLE_STATUS ioctl, it will not
receive back expected ":32:logon:my_prefix:my\ key" but the unescaped version
instead. Also userpace (most notably cryptsetup) is not ready to parse
single target argument containing (even escaped) whitespace chars and any
whitespace is simply taken as delimiter of another argument.
This effect is mitigated by the fact libdevmapper curently performs
double escaping of '\' char. Any user input in format "x\ x" is
transformed into "x\\ x" before being passed to the kernel. Nonetheless
dm-crypt may be used without libdevmapper. Therefore the near-term
solution to this is to reject any key string containing whitespace.
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The kernel key service is a generic way to store keys for the use of
other subsystems. Currently there is no way to use kernel keys in dm-crypt.
This patch aims to fix that. Instead of key userspace may pass a key
description with preceding ':'. So message that constructs encryption
mapping now looks like this:
<cipher> [<key>|:<key_string>] <iv_offset> <dev_path> <start> [<#opt_params> <opt_params>]
where <key_string> is in format: <key_size>:<key_type>:<key_description>
Currently we only support two elementary key types: 'user' and 'logon'.
Keys may be loaded in dm-crypt either via <key_string> or using
classical method and pass the key in hex representation directly.
dm-crypt device initialised with a key passed in hex representation may be
replaced with key passed in key_string format and vice versa.
(Based on original work by Andrey Ryabinin)
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The crypt_iv_operations are never modified, so declare them
as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In the past, dm-crypt used per-cpu crypto context. This has been removed
in the kernel 3.15 and the crypto context is shared between all cpus. This
patch renames the function crypt_setkey_allcpus to crypt_setkey, because
there is really no activity that is done for all cpus.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In crypt_set_key(), if a failure occurs while replacing the old key
(e.g. tfm->setkey() fails) the key must not have DM_CRYPT_KEY_VALID flag
set. Otherwise, the crypto layer would have an invalid key that still
has DM_CRYPT_KEY_VALID flag set.
Cc: stable@vger.kernel.org
Signed-off-by: Ondrej Kozina <okozina@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use bio_add_page(), the standard interface for adding a page to a bio,
rather than open-coding the same.
It should be noted that the 'clone' bio that is allocated using
bio_alloc_bioset(), in crypt_alloc_buffer(), does _not_ set the
bio's BIO_CLONED flag. As such, bio_add_page()'s early return for true
bio clones (those with BIO_CLONED set) isn't applicable.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Now that we don't need the common flags to overflow outside the range
of a 32-bit type we can encode them the same way for both the bio and
request fields. This in addition allows us to place the operation
first (and make some room for more ops while we're at it) and to
stop having to shift around the operation values.
In addition this allows passing around only one value in the block layer
instead of two (and eventuall also in the file systems, but we can do
that later) and thus clean up a lot of code.
Last but not least this allows decreasing the size of the cmd_flags
field in struct request to 32-bits. Various functions passing this
value could also be updated, but I'd like to avoid the churn for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
. add support for delaying the requeue of requests; used by DM multipath
when all paths have failed and 'queue_if_no_path' is enabled
. DM cache improvements to speedup the loading metadata and the writing
of the hint array
. fix potential for a dm-crypt crash on device teardown
. remove dm_bufio_cond_resched() and just using cond_resched()
. change DM multipath to return a reservation conflict error
immediately; rather than failing the path and retrying (potentially
indefinitely)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX7n9KAAoJEMUj8QotnQNab74IANm+rW2uYdpLNCxWUmcaih0d
BK8dLS/Mz35S0TRSekvynuBcPx18VP2Zueulc+aHTWcT4sj79l6KnVYT9g6c98rL
zzcv10QTteqhiiWwFmPHsZgv5dW8Y5wiRdt+SqcQ5sAHMFci6C05gzp9caNu7VTs
fbcLUdyYm40y3j84Lx/+ABXgnBhq+40OTtdnYSkEmLtdscPLzwpHgPmMctkrEl7e
7mqGC1KbDDzartqOZOeGP2P2qOCNN21qA+8ctMw9Xyze33uwvj7Vx6cro6e28wMm
ZClY9XNGlfuW9dCNtFR9o6NXS6NIK30UJbKqyZPPsK+70JrOgzh6GzQnwSXdyNs=
=7SkG
-----END PGP SIGNATURE-----
Merge tag 'dm-4.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- various fixes and cleanups for request-based DM core
- add support for delaying the requeue of requests; used by DM
multipath when all paths have failed and 'queue_if_no_path' is
enabled
- DM cache improvements to speedup the loading metadata and the writing
of the hint array
- fix potential for a dm-crypt crash on device teardown
- remove dm_bufio_cond_resched() and just using cond_resched()
- change DM multipath to return a reservation conflict error
immediately; rather than failing the path and retrying (potentially
indefinitely)
* tag 'dm-4.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (24 commits)
dm mpath: always return reservation conflict without failing over
dm bufio: remove dm_bufio_cond_resched()
dm crypt: fix crash on exit
dm cache metadata: switch to using the new cursor api for loading metadata
dm array: introduce cursor api
dm btree: introduce cursor api
dm cache policy smq: distribute entries to random levels when switching to smq
dm cache: speed up writing of the hint array
dm array: add dm_array_new()
dm mpath: delay the requeue of blk-mq requests while all paths down
dm mpath: use dm_mq_kick_requeue_list()
dm rq: introduce dm_mq_kick_requeue_list()
dm rq: reduce arguments passed to map_request() and dm_requeue_original_request()
dm rq: add DM_MAPIO_DELAY_REQUEUE to delay requeue of blk-mq requests
dm: convert wait loops to use autoremove_wake_function()
dm: use signal_pending_state() in dm_wait_for_completion()
dm: rename task state function arguments
dm: add two lockdep_assert_held() statements
dm rq: simplify dm_old_stop_queue()
dm mpath: check if path's request_queue is dying in activate_path()
...
Pull block layer updates from Jens Axboe:
"This is the main pull request for block layer changes in 4.9.
As mentioned at the last merge window, I've changed things up and now
do just one branch for core block layer changes, and driver changes.
This avoids dependencies between the two branches. Outside of this
main pull request, there are two topical branches coming as well.
This pull request contains:
- A set of fixes, and a conversion to blk-mq, of nbd. From Josef.
- Set of fixes and updates for lightnvm from Matias, Simon, and Arnd.
Followup dependency fix from Geert.
- General fixes from Bart, Baoyou, Guoqing, and Linus W.
- CFQ async write starvation fix from Glauber.
- Add supprot for delayed kick of the requeue list, from Mike.
- Pull out the scalable bitmap code from blk-mq-tag.c and make it
generally available under the name of sbitmap. Only blk-mq-tag uses
it for now, but the blk-mq scheduling bits will use it as well.
From Omar.
- bdev thaw error progagation from Pierre.
- Improve the blk polling statistics, and allow the user to clear
them. From Stephen.
- Set of minor cleanups from Christoph in block/blk-mq.
- Set of cleanups and optimizations from me for block/blk-mq.
- Various nvme/nvmet/nvmeof fixes from the various folks"
* 'for-4.9/block' of git://git.kernel.dk/linux-block: (54 commits)
fs/block_dev.c: return the right error in thaw_bdev()
nvme: Pass pointers, not dma addresses, to nvme_get/set_features()
nvme/scsi: Remove power management support
nvmet: Make dsm number of ranges zero based
nvmet: Use direct IO for writes
admin-cmd: Added smart-log command support.
nvme-fabrics: Add host_traddr options field to host infrastructure
nvme-fabrics: revise host transport option descriptions
nvme-fabrics: rework nvmf_get_address() for variable options
nbd: use BLK_MQ_F_BLOCKING
blkcg: Annotate blkg_hint correctly
cfq: fix starvation of asynchronous writes
blk-mq: add flag for drivers wanting blocking ->queue_rq()
blk-mq: remove non-blocking pass in blk_mq_map_request
blk-mq: get rid of manual run of queue with __blk_mq_run_hw_queue()
block: export bio_free_pages to other modules
lightnvm: propagate device_add() error code
lightnvm: expose device geometry through sysfs
lightnvm: control life of nvm_dev in driver
blk-mq: register device instead of disk
...
Mikulas Patocka