- The asm helpers for calling into irq tracer were missing
- Add calls to above helpers in low level assembly entry code for ARCv2
- irq_save() uses CLRI to disable interrupts and returns the prev interrupt
state (in STATUS32) in a specific encoding (and not the raw value of
STATUS32). This is usable with SETI in irq_restore(). However
save_flags() reads the raw value of STATUS32 which doesn't pair with
irq_save/restore() and thus needs fixing.
Signed-off-by: Evgeny Voevodin <evgeny.voevodin@intel.com>
[vgupta: updated changelog and also added some comments]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARConnect/MCIP Inter-Core-Interrupt module can't send interrupt to
local core. So use core intc capability to trigger software
interrupt to self, using an unsued IRQ #21.
This showed up as csd deadlock with LTP trace_sched on a dual core
system. This test acts as scheduler fuzzer, triggering all sorts of
schedulting activity. Trouble starts with IPI to self, which doesn't get
delivered (effectively lost due to H/w capability), but the msg intended
to be sent remain enqueued in per-cpu @ipi_data.
All subsequent IPIs to this core from other cores get elided due to the
IPI coalescing optimization in ipi_send_msg_one() where a pending msg
implies an IPI already sent and assumes other core is yet to ack it.
After the elided IPI, other core simply goes into csd_lock_wait()
but never comes out as this core never sees the interrupt.
Fixes STAR 9001008624
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org> [4.2]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Returning to delay slot, riding an interrupti, had one loose end.
AUX_USER_SP used for restoring user mode SP upon RTIE was not being
setup from orig task's saved value, causing task to use wrong SP,
leading to ProtV errors.
The reason being:
- INTERRUPT_EPILOGUE returns to a kernel trampoline, thus not expected to restore it
- EXCEPTION_EPILOGUE is not used at all
Fix that by restoring AUX_USER_SP explicitly in the trampoline.
This was broken in the original workaround, but the error scenarios got
reduced considerably since v3.14 due to following:
1. The Linuxthreads.old based userspace at the time caused many more
exceptions in delay slot than the current NPTL based one.
Infact with current userspace the error doesn't happen at all.
2. Return from interrupt (delay slot or otherwise) doesn't get exercised much
after commit 4de0e52867 ("Really Re-enable interrupts to avoid deadlocks")
since IRQ_ACTIVE.active being clear means most returns are as if from pure
kernel (even for active interrupts)
Infact the issue only happened in an experimental branch where I was tinkering with
reverted 4de0e52867
Cc: stable@kernel.org # v4.2+
Fixes: 4255b07f2c ("ARCv2: STAR 9000793984: Handle return from intr to Delay Slot")
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Bus errors from userspace on ARCompact based cores are handled by core
as a high priority L2 interrupt but current code treated it as interrupt
Handling an interrupt like exception is certainly not going to go unnoticed.
(and it worked so far as we never saw a Bus error from userspace until
IPPK guys tested a DDR controller with ECC error detection etc hence
needed to explicitly trigger/handle such errors)
- So move mem_service exception handler from common code into ARCv2 code.
- In ARCompact code, define mem_service as L2 interrupt handler which
just drops down to pure kernel mode and goes of to enqueue SIGBUS
Reported-by: Nelson Pereira <npereira@synopsys.com>
Tested-by: Ana Martins <amartins@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
For Run-on-reset, non masters need to spin wait. For Halt-on-reset they
can jump to entry point directly.
Also while at it, made reset vector handler as "the" entry point for
kernel including host debugger based boot (which uses the ELF header
entry point)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Evgeny Voevodin