Patch from Lennert Buytenhek
This patch makes the kernel save Crunch state in userland signal frames,
so that any userland signal handler can safely use the Crunch coprocessor
without corrupting the Crunch state of the code it preempted.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
ixp23xx was including asm/hardware.h in its version of uncompress.h,
to get at the physical address of the debug UART, but this include was
causing various inline functions that are totally unrelated to the
decompressor, defined in headers in include/asm-arm/arch-ixp23xx, to
be included in the decompressor image.
Include asm/arch/ixp23xx.h instead, and move the sole inline function
in ixp23xx.h to another header.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
Remove the remaining legacy __virt_to_bus__is_a_macro and
__bus_to_virt__is_a_macro defines in some ARM platforms.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
If only the S3C2412 based machines are selected,
then the regs-dsc.h does not export the S3C2412_DSC
registers as it is wrapped in CONFIG_CPU_S3C2440.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Back in the days when we had armo (26-bit) and armv (32-bit) combined,
we had an additional layer to the uaccess macros to ensure correct
typing. Since we no longer have 26-bit in this tree, we no longer
need this layer, so eliminate it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for both the S3C2412 and S3C2412 Samsung SoCs to
the increasingly mis-named s3c2410.c driver.
This currently only supports SLC ECCs, and a chip on nFCE0.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
- Initialize timer outside of spinlock to reduce the time the spinlock is held
- Do clk_get to the source clocks during initialization to avoid sleeping later
- New function to set counter register
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform config data for camera sensors. Since it includes pointers,
it should not be passed from the bootloader.
Signed-off-by: Samuel Ortiz <samuel.ortiz@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for omap24xx power domains and
allows suspend to work.
Please note that for some reason core power domain still
does not seem to idle.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement basic support for General-Purpose Memory Controller
as found on OMAP2420.
Dynamic CS address space allocation still needs to be done.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- DMA CSR register is cleared by reading on omap1, but on
omap2 it is cleard by writing to it.
- DMA TOUT interrupt does not exist on omap24xx, rename it
- Add SECURE and MISALIGNED errors by default for omap24xx
- Add defines for external DMA request lines
Signed-off-by: Tony Lindgren <tony@atomide.com>
Port dmtimer framework to OMAP2.
Modify the dmtimers API to support setting of PWM configuration and prescaler.
Convert 32 kHz timer and GP timer to use the dmtimer framework.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds core support for the TI F-Sample Board (OMAP 850).
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add backlight intensity control to the LOCOMO lcd/backlight driver using the
backlight class and add basic power management support.
This is a reimplementation and improvement of patches by John Lenz and Pavel
Machek
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The floppy driver is already calling add_disk_randomness as it should, so this
was redundant.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DEFAULT_FIQ was entirely unused. MODE_* are just redefinitions
of *_MODE. Use *_MODE instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As for RETINSTR/LOADREGS macros, these were for compatibility
with 26-bit ARMs. No longer required, so remove them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
RETINSTR is a left-over from the days when we had 26-bit and
32-bit CPU support integrated into the same tree. Since this
is no longer the case, we can now remove RETINSTR.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
In order for userspace to find saved coprocessor registers, move them from
struct rt_sigframe into struct ucontext. Also allow space for glibc's
sigset_t, so that userspace and kernelspace can use the same ucontext
layout. Define the magic numbers for iWMMXt in the header file for easier
reference. Include the size of the coprocessor data in the magic numbers.
Also define magic numbers and layout for VFP, not yet saved.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Move the decoding of the IRQ_EXT4 and above out of
the entry macro, and into an chained irq handler
as the EXTINT registers move depending on the CPU
being used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Serial port support for the on-board UART blocks
on the Samsung S3C2412 and S3C2413 UARTs.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Clock support for the clocks on the Samsung S3C2412
and S3C2413 SoCs. This provides clock enables and
parent selection for all the standard clocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add support for the Samsung S3C2412 and S3C2413 range
of SoCs. This patch contains the core identification,
debug macros, and basic register updates to get these
to build.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
Remove the remaining legacy __mem_isa() definitions for the ARM
platforms.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add an initial implementation of the clk_* API for the cirrus ep93xx
to the tree. The initial implementation is somewhat minimal, with the
intention of extending it as we go along.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct the return type of handle_IRQ_event() (inconsistency noticed during
Xen development), and remove redundant declarations. The return type
adjustment required breaking out the definition of irqreturn_t into a
separate header, in order to satisfy current include order dependencies.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (21 commits)
[ARM] 3629/1: S3C24XX: fix missing bracket in regs-dsc.h
[ARM] 3537/1: Rework DMA-bounce locking for finer granularity
[ARM] 3601/1: i.MX/MX1 DMA error handling for signaled channels only
[ARM] 3597/1: ixp4xx/nslu2: Board support for new LED subsystem
[ARM] 3595/1: ixp4xx/nas100d: Board support for new LED subsystem
[ARM] 3626/1: ARM EABI: fix syscall restarting
[ARM] 3628/1: S3C24XX: add get_rate call to struct clk
[ARM] 3627/1: S3C24XX: split s3c2410 clocks from core clocks
[ARM] 3613/1: S3C2410: Add sysdev and sysclass
[ARM] 3624/1: Report true modem control line states
[ARM] 3620/2: ixp23xx: add uengine loader support
[ARM] 3618/1: add defconfig for logicpd pxa270 card engine
[ARM] 3617/1: ep93xx: fix slightly incorrect timer tick rate
[ARM] 3616/1: fix timer handler wrap logic for a number of platforms
[ARM] 3615/1: ixp23xx: use platform devices for physmap flash
[ARM] 3614/1: ep93xx: use platform devices for physmap flash
[ARM] 3621/1: fix compilation breakage for pnx4008
[ARM] 3623/1: pnx4008: move GPIO-related defines to gpio.h
[ARM] 3622/1: pnx4008: remove clk_use/clk_unuse
[ARM] Enable VFP to be built when non-VFP capable CPUs are selected
...
This is a patch for the Hilscher netx builtin ethernet ports. The
netx board support was merged into 2.6.17-git2.
The netx is a arm926 based SoC.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
--
drivers/net/Kconfig | 11
drivers/net/Makefile | 1
drivers/net/netx-eth.c | 516 ++++++++++++++++++++++++++++++++++++++++
include/asm-arm/arch-netx/eth.h | 27 ++
4 files changed, 555 insertions(+)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
VGA_MAP_MEM translates to ioremap() on some architectures. It makes sense
to do this to vga_vram_base, because we're going to access memory between
vga_vram_base and vga_vram_end.
But it doesn't really make sense to map starting at vga_vram_end, because
we aren't going to access memory starting there. On ia64, which always has
to be different, ioremapping vga_vram_end gives you something completely
incompatible with ioremapped vga_vram_start, so vga_vram_size ends up being
nonsense.
As a bonus, we often know the size up front, so we can use ioremap()
correctly, rather than giving it a zero size.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
Fix missing bracket in include/asm-arm/arch-s3c2410/regs-dsc.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Pisa
There has been bug, that dma_err_handler() touches even
channels not signaling error condition.
Problem noticed by Andrea Paterniani.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch allows the ixp2000 uengine loader that is already in the
tree to also be used on the ixp23xx.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
pnx4008_defconfig fails to build:
include/asm/hardware/debug-8250.S: Assembler messages:
include/asm/hardware/debug-8250.S:12: Error: Macro with this name was already defined.
This is due to senduart macro erroneously defined in include/asm-arm/arch-pnx4008/debug-macro.S. This patch removes it from that file.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
This patch moves GPIO-related defines and static inline funcs from include/asm-arm/arch-pnx4008/pm.h to include/asm-arm/arch-pnx4008/gpio.h.
Also, some more GPIO-related defines are added to include/asm-arm/arch-pnx4008/gpio.h as they are needed for the USB host driver (coming soon...)
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some machine classes need to allow VFP support to be built into the
kernel, but still allow the kernel to run even though VFP isn't
present. Unfortunately, the kernel hard-codes VFP instructions
into the thread switch, which prevents this being run-time selectable.
Solve this by introducing a notifier which things such as VFP can
hook into to be informed of events which affect the VFP subsystem
(eg, creation and destruction of threads, switches between threads.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* git://git.infradead.org/hdrcleanup-2.6: (63 commits)
[S390] __FD_foo definitions.
Switch to __s32 types in joystick.h instead of C99 types for consistency.
Add <sys/types.h> to headers included for userspace in <linux/input.h>
Move inclusion of <linux/compat.h> out of user scope in asm-x86_64/mtrr.h
Remove struct fddi_statistics from user view in <linux/if_fddi.h>
Move user-visible parts of drivers/s390/crypto/z90crypt.h to include/asm-s390
Revert include/media changes: Mauro says those ioctls are only used in-kernel(!)
Include <linux/types.h> and use __uXX types in <linux/cramfs_fs.h>
Use __uXX types in <linux/i2o_dev.h>, include <linux/ioctl.h> too
Remove private struct dx_hash_info from public view in <linux/ext3_fs.h>
Include <linux/types.h> and use __uXX types in <linux/affs_hardblocks.h>
Use __uXX types in <linux/divert.h> for struct divert_blk et al.
Use __u32 for elf_addr_t in <asm-powerpc/elf.h>, not u32. It's user-visible.
Remove PPP_FCS from user view in <linux/ppp_defs.h>, remove __P mess entirely
Use __uXX types in user-visible structures in <linux/nbd.h>
Don't use 'u32' in user-visible struct ip_conntrack_old_tuple.
Use __uXX types for S390 DASD volume label definitions which are user-visible
S390 BIODASDREADCMB ioctl should use __u64 not u64 type.
Remove unneeded inclusion of <linux/time.h> from <linux/ufs_fs.h>
Fix private integer types used in V4L2 ioctls.
...
Manually resolve conflict in include/linux/mtd/physmap.h
Patch from Deepak Saxena
This patch makes soft reboot work on the Versatile board. Thanks to
Catalin Marinas @ ARM for pointing out the proper way to do this.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch removes some now unnecessary global variables -
at91_master_clock, at91_serial_map, at91_console_port.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This final patch includes some general fixes.
1. Link in pm.o if CONFIG_PM is enabled. [Should have been included in
patch 3605/1].
2. Use __raw_readl()/__raw_writel() when accessing System Peripheral
registers.
3. Removed some unnecessary includes
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds the core Power Management support for the AT91RM9200
processor. It will support suspend-to-RAM and standby modes.
The suspend-to-RAM functionality is not 100% complete. The code that
needs to be execute from the internal SRAM to restore the system is
outstanding. For now we just fall through to Standby mode.
The AT91-specific at91_suspend_entering_slow_clock() function will
eventually be replaced by clk_must_disable() once that functionality is
added to mainline clock API.
Patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch removes the now unnecessary
include/asm-arm/arch-at91rm9200/pio.h file. The pin configuration is
now handled in the platform-device setup code
(arch/arm/mach-at91rm9200/devices.c).
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Liam Girdwood
This patch adds some new PXA27x SSP port registers and also fixes the
SSP slots per frame macro
Changes:-
o SSCR0_SlotPerFrm fixed
o Added SSP port TSA, RSA, TSS and ACD registers
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Fix two typos in include/asm-arm/arch-ixp23xx.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Poodle Updates:
* Update corgi_ssp to make the GPIO chip selects optional
* Enable corgi_ssp for use by poodle
* Add corgi touchscreen platform device for poodle
* Export locomo platform device.
* Set framebuffer device parent correctly
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Abstract some machine specific parameters from the sharpsl_pm core
into the machine specific drivers. This allows the core to support
tosa/poodle.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Correct the Poodle power control for the MMC/SD port. Also
add write protection switch support.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Add functionality to allow machine specific reboot handlers on ARM.
Add machine specific reboot and poweroff handlers for all PXA Zaurus
models.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch includes a number of updates to the AT91RM9200 serial driver.
Changes include:
1. Conversion to a platform_driver. [Ivan Kokshaysky]
2. Replaced all references to AT91RM9200 with AT91. This driver can now
also be used for the AT91SAM9216.
3. Allow TIOCM_LOOP to configure local loopback mode.
4. Cleaned up the 'read_status_mask' usage and interrupt handler code.
[Chip Coldwell]
5. Suspend/resume support. [David Brownell]
There are a few 'unused variable' warning when compiling this - I
removed the new DMA support to keep this first patch simpler.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch includes the structures and exported functions required for
the platform-device support (added in patch 3585/1).
Also adds the arch_identify() function for run-time detection of which
AT91 processor the code is running on. [Original patch from Ivan
Kokshaysky]
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
These headers define the registers and bits for the SPI (Serial
Peripheral Interface), SSC (Synchronous Serial), TC (Timer/Counter) and
UDP (USB Device) peripherals integrated in the AT91RM9200 processor.
(They will probably also be usable for the AT91SAM9 series of SoC
processors)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
Added definition for the bits in the Chip ID register.
Corrected the capitalization of AT91_RTC_AMPM register name.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The byte order functions are visible to userspace. Unfortunately,
__arch_swab32() contains an assembly instruction which is invalid when
compiling for Thumb. This reverts to the C version when compiling for
Thumb.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
The netX processors have generic network bitstream engines (XMAC/XPEC).
This driver adds support for firmware loading and start, stop, reset
commands.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds support for the pointer FIFOs on netX.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds the base support for Hilscher's netX network
processors.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch maps the AT91RM9200's internal SRAM into the virtual memory
address space - just below the internal peripheral registers.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds the register definitions for Hilscher's netX network
processors.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Core support for the Samsung S3C2442, and the
serial port driver update to allow the serial
port blocks to be used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch fixes some dyntick locking issues on ARM as pointed
out by Russell King.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Using the low-level debug routines early in the
kernel debug cause the 1:1 mapping to get into
the TLB, which is not flushed until after the
CPU detection process (which needs the GPIO VA).
This patch moves the VA for the GPIO to the
same offset as the physical offset of the UART
to the GPIO.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vitaly Wool
This patch adds kernel headers for PNX4008 ARM platform.
It's basically the same as the previos one, but with the rmk's comments taken into account.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Updates to the lpd7a40x_platform files. Includes support for new
architecture, lpd7a400.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Updates to the lpd7a40x platform headers. Includes support for new
architecture, lpd7a400.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These include nothing more than the basic set of files listed in
asm-generic/Kbuild.asm. Any extra arch-specific files will need to be
added.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Patch from Richard Purdie
Add a power budget variable to the PXA OHCI platform data and add a
default value for the spitz platform(s) which prevents known failures
with certain USB devices.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replacing mistyped "buad" with "baud" where applicable.
Signed-off-by: Horst Schirmeier <horst@schirmeier.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The current __ixp23xx_arch_is_coherent() check assumes that the
lower byte of IXP23XX_PRODUCT_ID is identical to the lower byte of
processor_id, but this is not the case, and because of this we were
incorrectly enabling coherency on A1 stepping CPUs.
Stepping A1 of the ixp2350, which has a PRODUCT_ID of 0x401, has '02'
in the lower byte of processor_id, while A2, with a PRODUCT_ID of
0x402, has '04' in the lower byte of processor_id.
So, to check for >= A2, we really need to check the lower byte of
processor_id against >= 4.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM Architecture Reference Manual lists bit 4 of the PMD as "implementation
defined" and it must be set to zero on Intel XScale CPUs or the cache does
not behave properly. Found by Mike Rapoport while debugging a flash issue
on the PXA255:
http://marc.10east.com/?l=linux-arm-kernel&m=114845287600782&w=1
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix some outstanding issues with the pxa2xx_spi driver when running on a
PXA270:
- Wrong timeout calculation in the setup function due to different
peripheral clock rates in the PXAxxx family.
- Bad handling of SSSR_TFS interrupts in interrupt_transfer function.
- Added locking to interface between the pump_messages workqueue and the
pump_transfers tasklet.
Much thanks to Juergen Beisert for the extensive testing on the PXA270.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hardware based SPI driver for Samsung S3C24XX SoC systems
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SPI driver for SPI by GPIO on the Samsung S3C24XX series of SoC processors.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Catalin Marinas
Recent patches introduced the write_can_lock() call in the kernel/ptrace.c
file. Implement the __raw_* variants on ARM (SMP) as well.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This driver turns a PXA2xx synchronous serial port (SSP) into a SPI master
controller (see Documentation/spi/spi_summary). The driver has the following
features:
- Support for any PXA2xx SSP
- SSP PIO and SSP DMA data transfers.
- External and Internal (SSPFRM) chip selects.
- Per slave device (chip) configuration.
- Full suspend, freeze, resume support.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Uwe Zeisberger
The symbol is only used in arch/arm/kernel/head-common.S. This in turn
is included from arch/arm/kernel/head.S and arch/arm/kernel/head-nommu.S
which include asm-offsets.h .
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Include hardware.h in debug-macro.S, otherwise io_p2v is undefined.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Since git commit 2b78838842, entry-macro.S needs to include asm/arch/irqs.h
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch fixes the addruart macro to work with both mmu enabled and
disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
... but only for user space.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Intel PXA27x developers manual section 5.4.1.1 lists a priority
distribution for the DMA channels differently than what the code
currently assumes. This patch fixes that.
Noticed by Simon Vogl <vogl@soft.uni-linz.ac.at>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
... for the definition of NULL.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch moves the i.MX uart resources and the gpio pin setup to the
board files. This allows the boards to decide how many internal uarts
are connected to the outside world and whether they use rts/cts or
not.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch allows for the addition of IXP4xx systems that do not make
use of the PCI interface by moving the CONFIG_PCI symbol selection to
be platform-specific instead of for all of IXP4xx. If at least one machine
with PCI support is built, the PCI code will be compiled in, but when
building !PCI, this will drastically shrink the kernel size.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Markus Gutschke
In order to prevent gcc from making incorrect optimizations, all asm()
statements that define system calls should report memory as
clobbered. Recent versions of the headers for i386 have been changed
accordingly, but the ARM headers are still defective.
This patch fixes the bug tracked at
http://bugzilla.kernel.org/show_bug.cgi?id=6205
Signed-off-by: Markus Gutschke <markus@google.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These aren't needed by glibc or klibc, and they're broken in some cases
anyway. The uClibc folks are apparently switching over to stop using
them too (now that we agreed that they should be dropped, at least).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Patch from Nicolas Pitre
Avoid confusion for libraries assuming that a given syscall is available
when corresponding symbol is defined.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
GPIO LED support for Samsung S3C24XX SoC series processors.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current implementations define NODES_SHIFT in include/asm-xxx/numnodes.h for
each arch. Its definition is sometimes configurable. Indeed, ia64 defines 5
NODES_SHIFT values in the current git tree. But it looks a bit messy.
SGI-SN2(ia64) system requires 1024 nodes, and the number of nodes already has
been changeable by config. Suitable node's number may be changed in the
future even if it is other architecture. So, I wrote configurable node's
number.
This patch set defines just default value for each arch which needs multi
nodes except ia64. But, it is easy to change to configurable if necessary.
On ia64 the number of nodes can be already configured in generic ia64 and SN2
config. But, NODES_SHIFT is defined for DIG64 and HP'S machine too. So, I
changed it so that all platforms can be configured via CONFIG_NODES_SHIFT. It
would be simpler.
See also: http://marc.theaimsgroup.com/?l=linux-kernel&m=114358010523896&w=2
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Catalin Marinas
The X variants are deprecated starting with ARMv6. Using the D variants,
the fpmx_state in vfp_hard_struct is no longer needed.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The debug-8250 macros do byte accesses, which means that if we're in
big-endian mode, we need to logically OR the UART address with 3, as
the LSB byte lane (where UART data and status is transferred) has the
highest byte address in the word when we are in big-endian mode.
It's unclear why this problem didn't surface earlier.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
FLUSH_BASE must be visible to arch/arm/mm/init.c in order for the
memory region to be setup. Move these definitions from
asm-arm/arch-*/hardware.h into asm-arm/arch-*/memory.h where mm
stuff can see them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes arch_local_page_offset(pfn,nid) in arm.
This new one (added by unify_pfn_to_page patches) is obviously buggy.
This macro calculate page offset in a node.
Note: about LOCAL_MAP_NR()
comment in arm's sub-archs says...
/*
* Given a kaddr, LOCAL_MAP_NR finds the owning node of the memory
* and returns the index corresponding to the appropriate page in the
* node's mem_map.
*/
but LOCAL_MAP_NR() is designed to be able to take both paddr and kaddr.
In this case, paddr is better.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitu.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Pisa
This patch adds support of i.MX/MX1 SD/MMC controller.
It has been significantly redesigned from the original Sascha Hauer's
version to support scatter-gather DMA, to conform to latest Pierre Ossman's
and Russell King's MMC-SD Linux 2.6.x infrastructure.
The handling of all events has been moved to the softirq context
and is designed with no busy-looping in mind. Unfortunately
some controller bugs has to be overcome by limited looping
about 2-20 usec but these are observed only for initial card
recognition phase.
There are still some missing/missed IRQs problems under heavy load.
Help of somebody with access to the full SDHC design information
is probably necessary.
Regenerated against 2.6.16-git-060402 to solve clash with other patches.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds support for the MMC/SD card interface on the Atmel
AT91RM9200 processor.
Original driver was by Nick Randell, but a number of people have
subsequently worked on it. It's currently maintained by Malcolm Noyes.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs OMAP board support with linux-omap tree.
The highlights of the patch are:
- Add support for Nokia 770 by Juha Yrjola
- Add support for Samsung Apollon by Kyungmin Park
- Add support for Amstrad E3 videophone by Jonathan McDowell
- Remove board-netstar.c board support as requested by Ladislav Michl
- Do platform_device registration in board files by Komal Shah et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update misc OMAP core code from linux-omap tree:
- McBSP updates by Samuel Ortiz, Andrzej Zaborowski
- Whitespace cleanups by Ladislav Michl
- Other fixes by various linux-omap developers
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP framebuffer low-level init code from linux-omap tree
by Imre Deak.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP PM code from linux-omap tree:
- Move PM code from plat-omap to mach-omap1 and mach-omap2
by Tony Lindgren
- Add minimal PM support for omap24xx by Tony Lindgren and
Richard Woodruff
- Misc updates to omap1 PM code by Tuukka Tikkanen et al
- Updates to the SRAM code needed for PM and FB by Imre Deak
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP pin multiplexing code from linux-omap tree.
This patch adds new pin configurations by various OMAP
developers, and suport for omap730 by Brian Swetland.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP timers from linux-omap tree. The highlights of the
patch are:
- Move timer32k code from mach-omap1 to plat-omap and make it
work also on omap24xx by Tony Lindgren
- Add support for dmtimer idle check for PM by Tuukka Tikkanen
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP clock framework from linux-omap tree.
The highlights of the patch are:
- Add support for omap730 clocks by Andrzej Zaborowski
- Fix compile warnings by Dirk Behme
- Add support for using dev id by Tony Lindgren and Komal Shah
- Move memory timings and PRCM into separate files by Tony Lindgren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch updates the platform device resources for the Ethernet and
MMC peripherals. It also adds platform device information for the NAND
(SmartMedia), I2C and the RTC.
(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds support for the LED(s) on the AT91RM9200-based boards.
(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Pisa
This patch contains simplified set of changes to add scatter-gather
emulation capability into MX1 DMA support. The result should
be still usable for next combination of DMA transfers
Statter-Gather/linear/2D/FIFO to linear/2D/FIFO and
linear/2D/FIFO to Statter-Gather/2D/FIFO
The patch corrects channel priority allocation to be compatible
with MX1 hardware implementation.
Previous code has not been adapted from its PXA original.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Instantiate the recently merged m48t86 rtc driver in the ts72xx code.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Remove the old debug from the IRQ entry code,
update the comments on the handling of the
IRQ registers.
The message "bad interrupt offset" is removed
as it is only helpful for debugging, and can
cause printk() flooding when under load.
Make the code to deal with GPIO interrupts
faster, and use the same path to deal with
unexplained results from the IRQ registers.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the I/O coherent cache available on the
xsc3. The approach is to provide a simple API to determine whether the
chipset supports coherency by calling arch_is_coherent() and then
setting the appropriate system memory PTE and PMD bits. In addition,
we call this API on dma_alloc_coherent() and dma_map_single() calls.
A generic version exists that will compile out all the coherency-related
code that is not needed on the majority of ARM systems.
Note that we do not check for coherency in the dma_alloc_writecombine()
function as that still requires a special PTE setting. We also don't
touch dma_mmap_coherent() as that is a special ARM-only API that is by
definition only used on non-coherent system.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
On the Double Espresso board, the IXP2350s are PCI slave devices and
we skip calling pci_common_init() as that enumerates the bus. But even
though we are a PCI slave device, there is still some PCI-related setup
that has to be done.
Create ixp23xx_pci_common_init(), move the common initialisation bits
there, and have this function called from both the PCI master and the
PCI slave init path.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3424/2: ixp23xx: fix uncompress.h for recent CRLF decompressor change
[ARM] 3434/1: pxa i2s amsl define
[ARM] 3425/1: xsc3: need to include pgtable-hwdef.h
[ARM] Allow un-muxed syscalls to be available for everyone
[ARM] 3420/1: Missing clobber in example code
[ARM] nommu: fixups for the exception vectors
[ARM] nommu: add nommu specific Kconfig and MMUEXT variable in Makefile
[ARM] nommu: start-up code
[ARM] nommu: MPU support in boot/compressed/head.S
Generalise the Corgi backlight driver by moving the default intensity and
limit mask settings into the platform specific data structure. This enables
the driver to support other Zaurus hardware, specifically the SL-6000x (Tosa)
model.
Also change the spinlock to a mutex (the spinlock is overkill).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for the Compact Flash controller integrated in
the Atmel AT91RM9200 processor.
Signed-off-by: Andrew Victor <andrew@sanpeople.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Patch from Lennert Buytenhek
Adapt ixp23xx uncompress.h to a081568d70.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc-Andre Hebert
The error concerns a bit mask define for the AMSL bit of the SACR1 register in the 2.6 kernel tree. The AMSL is bit 0 and it was defined as so in the 2.4 kernel tree but it is inccorrectly set as bit 1 (a reserved bit) in the 2.6 kernel tree.
Signed-off-by: Marc-Andre Hebert <marcandreh@humanware.ca>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's been a while since the un-muxed socket and ipc syscalls were
introduced, so make the unistd.h number definitions visible for
non-EABI as well as EABI.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the Intel ixp23xx series of CPUs. The
ixp23xx is an XSC3 based CPU with 512K of L2 cache, a 64bit 66MHz PCI
interface, two DDR RAM interfaces, QDR RAM interfaces, two gigabit
MACs, two 10/100 MACs, expansion bus, four microengines, a Media and
Switch Fabric unit almost identical to the one on the ixp2400, two
xscale (8250ish) UARTs and a bunch of other stuff.
This patch adds the core ixp23xx support code, and support for the
ADI Engineering Roadrunner, Intel IXDP2351, and IP Fabrics Double
Espresso platforms.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add support for the LogicPD PXA270 Card Engine.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the new XScale v3 core. This is an
ARMv5 ISA core with the following additions:
- L2 cache
- I/O coherency support (on select chipsets)
- Low-Locality Reference cache attributes (replaces mini-cache)
- Supersections (v6 compatible)
- 36-bit addressing (v6 compatible)
- Single instruction cache line clean/invalidate
- LRU cache replacement (vs round-robin)
I attempted to merge the XSC3 support into proc-xscale.S, but XSC3
cores have separate errata and have to handle things like L2, so it
is simpler to keep it separate.
L2 cache support is currently a build option because the L2 enable
bit must be set before we enable the MMU and there is no easy way to
capture command line parameters at this point.
There are still optimizations that can be done such as using LLR for
copypage (in theory using the exisiting mini-cache code) but those
can be addressed down the road.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As per the corresponding change to the serial drivers, arrange
for ARM decompressors to give CRLF. Move the common putstr code
into misc.c such that machines only need to supply "putc" and
"flush" functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes from the ARM subsytem some of the rtc-related functions
that have been included in the RTC subsystem. It also fixes some naming
collisions.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ARM can use generic funcs.
PFN_TO_NID, LOCAL_MAP_NR are defined by sub-archs.
Signed-off-by: KAMEZAWA Hirotuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Lennert Buytenhek
The Redboot version that cirrus supplies for the cirrus ep93xx doesn't
turn off DMA from the ethernet MAC before jumping to linux, which means
that we might end up with bits of RX status and packet data scribbled
over the uncompressed kernel image.
Work around this by resetting the ethernet MAC before we uncompress.
We don't usually work around bootloader bugs, but considering that the
large majority of ep93xx boards out there have this problem, I figured
this it was justified in this case.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch defines constant_fls() instead of removed generic_fls().
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3030/2: fix permission check in the obscur cmpxchg syscall
[ARM] nommu: rename compressed/head.S symbols to a new style
[ARM] select TLS_REG_EMUL and NEEDS_SYSCALL_FOR_CMPXCHG
[ARM] nommu: Move hardware page table definitions to pgtable-hwdef.h
[ARM] Move read of processor ID out of lookup_processor_type()
[ARM] Fix typo in tlbflush.h
[ARM] noMMU: removes TLB codes in nommu mode
[ARM] noMMU: block sys_fork in nommu mode
[ARM] 3399/1: Fix link problem when CONFIG_PRINTK is disabled
[ARM] 3398/1: Fix the VFP registers loading/storing base address
[ARM] 3397/1: AT91RM9200 Header update
[ARM] 3385/1: Battery support for sharp zaurus sl-5500 (collie)
[ARM] SMP: don't set cpu_*_map in smp_prepare_boot_cpu
include/linux/clk.h is betraying its ARM origins
[ARM] Move enable_irq and disable_irq to assembler.h
[ARM] 3391/1: use PLAT8250_DEV_PLATFORM{,1} for platform device id instead of 0/1
Patch from Andrew Victor
This patch updates the hardware header to include definitions for the
Memory Controller registers.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement the half-closed devices notifiation, by adding a new POLLRDHUP
(and its alias EPOLLRDHUP) bit to the existing poll/select sets. Since the
existing POLLHUP handling, that does not report correctly half-closed
devices, was feared to be changed, this implementation leaves the current
POLLHUP reporting unchanged and simply add a new bit that is set in the few
places where it makes sense. The same thing was discussed and conceptually
agreed quite some time ago:
http://lkml.org/lkml/2003/7/12/116
Since this new event bit is added to the existing Linux poll infrastruture,
even the existing poll/select system calls will be able to use it. As far
as the existing POLLHUP handling, the patch leaves it as is. The
pollrdhup-2.6.16.rc5-0.10.diff defines the POLLRDHUP for all the existing
archs and sets the bit in the six relevant files. The other attached diff
is the simple change required to sys/epoll.h to add the EPOLLRDHUP
definition.
There is "a stupid program" to test POLLRDHUP delivery here:
http://www.xmailserver.org/pollrdhup-test.c
It tests poll(2), but since the delivery is same epoll(2) will work equally.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for the Ethernet controller integrated in the
Atmel AT91RM9200 SoC processor.
Changes since the previous submission (01/02/2006) are:
- Make use of the clk.h clock infrastructure.
- The multicast hash function is not crc32. [Patch by Pedro Perez]
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
unused isa_...() helpers removed.
Adrian Bunk:
The asm-sh part was rediffed due to unrelated changes.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
5d25ac038a broke VFP builds due to
enable_irq not being defined as an assembly macro. Move it to
assembler.h so everyone can use it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The original version of the chip docs had the PW and SU fields in
the slowport write timing control register accidentally reversed.
This is mentioned in the errata (documentation change #4) and fixed
in newer docs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
On the IXDP2x00s, the NPU that is PCI master is always the egress
(i.e. 'master') NPU. At least on the IXDP2800, both NPUs have flash,
so the ixp2000_has_flash() check in ixdp2x00_master_npu() is useless.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
The xscale UART in the ixp2000 is basically just an 8250 UART (with
some extra bits and pieces), so we can use the generic 8250 debug
macros on the ixp2000.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only issue a "nobody cared" warning after 99900 spurious interrupts.
This avoids the occasional spurious interrupt causing warnings, as
per x86.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add GPIO interrupt support for the first 16 GPIO lines (port A
and B.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Move the uengine loader from arch/arm/mach-ixp2000 to arch/arm/common
so that ixp23xx can use it too.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Add support for setting the direction of and getting/setting the
value of the 64 GPIO lines.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the Cirrus ep93xx series of CPUs. The
ep93xx is an ARM920T based CPU with two VICs, PL010 based UARTs,
IrDA, MaverickCrunch floating point coprocessor, between 24 and 64
GPIOs, ethernet, OHCI USB and, depending on the model, pcmcia, raster
engine, graphics accelerator, IDE controller and a bunch of other
stuff.
This patch adds the core ep93xx support code, and support for the
Glomation GESBC-9312-sx and the Technologic Systems TS-72xx SBCs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
This patch adds a few defines that are useful
to configure the CS regions on ixp4xx.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: OEyvind Repvik <oyvind@repvik.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Peter Teichmann
Currently, if the kernels HZ value is greater than 100, delays with the udelay function are too short. This can cause trouble for instance with the zd1201 usb wlan driver.
This patch suggests a solution that keeps the overhead small and maintains (hopefully) sufficient resolution.
Signed-off-by: Peter Teichmann
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This patch adds support for Intel's IXDP28x5 platform. This
is just and IXDP2801 with a new CPU rev but the bootloader
has been updated to reflect a new machine ID so we just build
support for it by default when we build IXDP2801.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add enable and set_parent calls for the dclk
and clkout clocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Support for Simtec IM2440D20 CPU modules (Osiris)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This field is redundent since it must be equal to PHYS_OFFSET anyway.
There is no reference to it anymore so remove it at last.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Several ARM machine implementations used a PL01x primecell compatible
serial port for debugging purposes, and indepdently implemented the low
level debug macros every time. Provide a common implementation and
convert these implementations to use this version.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Several ARM machine implementations used an 8250 compatible port for
debugging purposes, and indepdently implemented the low level debug
macros every time. Provide a common implementation and convert these
implementations to use this version.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some SoCs have multiple VIC devices. Adapt the generic vic code
to allow multiple implementations to be handled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In all current use cases, "chipdata" is used to store an iomem address.
Mark it with __iomem, and rename it to 'base'. Leave the accessor macros
alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/arch/irq.h used to be included from asm/irq.h, but was removed
from the ARM kernel a long time ago. Consequently, the contents
of asm/arch/irq.h (which mostly contain a definition for fixup_irq())
have not been used. Hence, remove asm/arch/irq.h.
Some machine support files incorrectly included this file, making
little or no use of the contents. Move the contents to a local
include file, and remove those include statements as well.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the HZ definition into Kconfig, and set appropriate defaults
for platforms. Remove mostly empty asm/arch/param.h include file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the hardware PMD and PTE page table definitions from pgtable.h
into pgtable-hwdef.h, and include pgtable-hwdef.h as necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes TLB related codes in nommu mode.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The enable_hlt and disable_hlt should be declared in
include/asm/setup.h. This fixes sparse errors from
arch/arm/kernel/process.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the reliance of iwmmxt on hand coded alignments.
Since thread_info is always 8K aligned, specifying that fpstate is
8-byte aligned achieves the same effect without needing to resort
to hand coded alignments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Chapter B2.7.3 in the latest ARM ARM (with v6 information) states that
the completion of a TLB maintenance operation is only guaranteed by
the execution of a DSB (Data Syncronization Barrier, formerly Data
Write Barrier or Drain Write Buffer).
Note that a DSB is only needed in the flush_tlb_kernel_* functions
since the completion is guaranteed by a mode change (i.e. switching
back to user mode) for the flush_tlb_user_* functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds the at91_set_multi_drive() function to enable/disable
the multi-drive (open collector) pin capability on the AT91RM9200
processor.
This is necessary to fix the UDC (USB Gadget) driver for the AT91RM9200
board as it will not allow the board reset line to be pulled low if the
pullup is not driven as an open collector output as the boards are wired
to the USB connector on both the DK/EK.
This version of the patch updates it to 2.6.16-rc4.
Orignal patch by Jeff Warren.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
The I2C pin assignment for the Iomega NAS100d board was incorrect. This
patch fixes it. The correct assignment has now been tested using the
new RTC class and a new driver for the RTC on the NAS100d.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
With EABI the multiplex sys_ipc and sys_socketcall syscalls are
unavailable and their support code even removed from the compiled
kernel, and the new unmuxed syscalls must be used instead.
Make those syscall numbers visible.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A change to the SMP initialisation caused the following oops:
CPU1: Booted secondary processor
CPU1: D VIPT write-back cache
CPU1: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU1: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
<7>Calibrating delay loop... 83.14 BogoMIPS (lpj=415744)
<1>Unable to handle kernel NULL pointer dereference at virtual address 0000001c
...
PC is at enqueue_task+0x1c/0x64
LR is at activate_task+0xcc/0xe4
SMP initialisation now requires cpu_possible_map to be initialised in
setup_arch(). Move this from smp_prepare_cpus() to smp_init_cpus()
and call it from our setup_arch() if CONFIG_SMP is enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make new MADV_REMOVE, MADV_DONTFORK, MADV_DOFORK consistent across all
arches. The idea is to make it possible to use them portably even before
distros include them in libc headers.
Move common flags to asm-generic/mman.h
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, copy-on-write may change the physical address of a page even if the
user requested that the page is pinned in memory (either by mlock or by
get_user_pages). This happens if the process forks meanwhile, and the parent
writes to that page. As a result, the page is orphaned: in case of
get_user_pages, the application will never see any data hardware DMA's into
this page after the COW. In case of mlock'd memory, the parent is not getting
the realtime/security benefits of mlock.
In particular, this affects the Infiniband modules which do DMA from and into
user pages all the time.
This patch adds madvise options to control whether memory range is inherited
across fork. Useful e.g. for when hardware is doing DMA from/into these
pages. Could also be useful to an application wanting to speed up its forks
by cutting large areas out of consideration.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
Define the bits for the two board control latches
that control various items on the H1940 iPAQ.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch adds the missing cache flushes to common low-level
init that are needed to access the IO region. These flushes
are normally done at the end of devicemaps_init(), but we
need to detect the OMAP core type early.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Since:
if (unlikely(__res || __ex_flag))
produces worse code on ARM than:
if (unlikely(__res | __ex_flag))
I therefore made it more explicit:
__res |= __ex_flag;
if (unlikely(__res != 0))
so it is not seen as a typo again.
Also made everything static inline rather than macros for better readability
(both produce the same code after all).
And finally added missing \t from multi-line assembly code.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lucas Correia Villa Real
This patch adds support to GPIO on the S3C2400, which is going to
be used by the GP32 machine and the SMDK2400 development board.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
ip_fast_csum() accesses memory via a pointer (iph) within an
asm function. To prevent memory corruption when the function is
inlined, it needs "memory" on the clobber list.
This fixes ip checksum errors reported by a Zaurus user.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
This Freescale Semiconductor, Inc. contributed patch adds mem_types[]
support for ARMv6 non-shared device memory region attributes. This
implementation provides support for only first level section mapped
non-shared devices. Second level non-shared device mappings are not
yet supported.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lucas Correia Villa Real
This patch defines S3C2400 memory map and adds a S3C24XX macro for
common resources between S3C2400, S3C2410 and S3C2440 cpus.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Lennert Buytenhek