Two fixes for nasty kexec/kdump crashes in certain configurations.
A couple of minor fixes for the new TIDR code.
A fix for an oops in a CXL error handling path.
Thanks to:
Andrew Donnellan, Christophe Lombard, David Gibson, Mahesh Salgaonkar, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----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=/LD/
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two fixes for nasty kexec/kdump crashes in certain configurations.
A couple of minor fixes for the new TIDR code.
A fix for an oops in a CXL error handling path.
Thanks to: Andrew Donnellan, Christophe Lombard, David Gibson, Mahesh
Salgaonkar, Vaibhav Jain"
* tag 'powerpc-4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Do not assign thread.tidr if already assigned
powerpc: Avoid signed to unsigned conversion in set_thread_tidr()
powerpc/kexec: Fix kexec/kdump in P9 guest kernels
powerpc/powernv: Fix kexec crashes caused by tlbie tracing
cxl: Check if vphb exists before iterating over AFU devices
A small batch of fixes, about 50% tagged for stable and the rest for recently
merged code.
There's one more fix for the >128T handling on hash. Once a process had
requested a single mmap above 128T we would then always search above 128T. The
correct behaviour is to consider the hint address in isolation for each mmap
request.
Then a couple of fixes for the IMC PMU, a missing EXPORT_SYMBOL in VAS, a fix
for STRICT_KERNEL_RWX on 32-bit, and a fix to correctly identify P9 DD2.1 but in
code that is currently not used by default.
Thanks to:
Aneesh Kumar K.V, Christophe Leroy, Madhavan Srinivasan, Sukadev Bhattiprolu.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gv70
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A small batch of fixes, about 50% tagged for stable and the rest for
recently merged code.
There's one more fix for the >128T handling on hash. Once a process
had requested a single mmap above 128T we would then always search
above 128T. The correct behaviour is to consider the hint address in
isolation for each mmap request.
Then a couple of fixes for the IMC PMU, a missing EXPORT_SYMBOL in
VAS, a fix for STRICT_KERNEL_RWX on 32-bit, and a fix to correctly
identify P9 DD2.1 but in code that is currently not used by default.
Thanks to: Aneesh Kumar K.V, Christophe Leroy, Madhavan Srinivasan,
Sukadev Bhattiprolu"
* tag 'powerpc-4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Fix Power9 DD2.1 logic in DT CPU features
powerpc/perf: Fix IMC_MAX_PMU macro
powerpc/perf: Fix pmu_count to count only nest imc pmus
powerpc: Fix boot on BOOK3S_32 with CONFIG_STRICT_KERNEL_RWX
powerpc/perf/imc: Use cpu_to_node() not topology_physical_package_id()
powerpc/vas: Export chip_to_vas_id()
powerpc/64s/slice: Use addr limit when computing slice mask
Rebooting into a new kernel with kexec fails in trace_tlbie() which is
called from native_hpte_clear(). This happens if the running kernel
has CONFIG_LOCKDEP enabled. With lockdep enabled, the tracepoints
always execute few RCU checks regardless of whether tracing is on or
off. We are already in the last phase of kexec sequence in real mode
with HILE_BE set. At this point the RCU check ends up in
RCU_LOCKDEP_WARN and causes kexec to fail.
Fix this by not calling trace_tlbie() from native_hpte_clear().
mpe: It's not safe to call trace points at this point in the kexec
path, even if we could avoid the RCU checks/warnings. The only
solution is to not call them.
Fixes: 0428491cba ("powerpc/mm: Trace tlbie(l) instructions")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
While computing slice mask for the free area we need make sure we only
search in the addr limit applicable for this mmap. We update the
slb_addr_limit after we request for a mmap above 128TB. But the
following mmap request with hint addr below 128TB should still limit
its search to below 128TB. ie. we should not use slb_addr_limit to
compute slice mask in this case. Instead, we should derive high addr
limit based on the mmap hint addr value.
Fixes: f4ea6dcb08 ("powerpc/mm: Enable mappings above 128TB")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Non-highlights:
- Five fixes for the >128T address space handling, both to fix bugs in our
implementation and to bring the semantics exactly into line with x86.
Highlights:
- Support for a new OPAL call on bare metal machines which gives us a true NMI
(ie. is not masked by MSR[EE]=0) for debugging etc.
- Support for Power9 DD2 in the CXL driver.
- Improvements to machine check handling so that uncorrectable errors can be
reported into the generic memory_failure() machinery.
- Some fixes and improvements for VPHN, which is used under PowerVM to notify
the Linux partition of topology changes.
- Plumbing to enable TM (transactional memory) without suspend on some Power9
processors (PPC_FEATURE2_HTM_NO_SUSPEND).
- Support for emulating vector loads form cache-inhibited memory, on some
Power9 revisions.
- Disable the fast-endian switch "syscall" by default (behind a CONFIG), we
believe it has never had any users.
- A major rework of the API drivers use when initiating and waiting for long
running operations performed by OPAL firmware, and changes to the
powernv_flash driver to use the new API.
- Several fixes for the handling of FP/VMX/VSX while processes are using
transactional memory.
- Optimisations of TLB range flushes when using the radix MMU on Power9.
- Improvements to the VAS facility used to access coprocessors on Power9, and
related improvements to the way the NX crypto driver handles requests.
- Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit.
Thanks to:
Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew Donnellan, Aneesh
Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin Herrenschmidt, Breno Leitao,
Christophe Leroy, Christophe Lombard, Cyril Bur, Frederic Barrat, Gautham R.
Shenoy, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo Romero, Haren
Myneni, Joel Stanley, Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami
Hiramatsu, Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia Franco de
Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee, Shriya, Stephen
Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel Datwyler, Vaibhav Jain,
Vaidyanathan Srinivasan, William A. Kennington III.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Rq81
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"A bit of a small release, I suspect in part due to me travelling for
KS. But my backlog of patches to review is smaller than usual, so I
think in part folks just didn't send as much this cycle.
Non-highlights:
- Five fixes for the >128T address space handling, both to fix bugs
in our implementation and to bring the semantics exactly into line
with x86.
Highlights:
- Support for a new OPAL call on bare metal machines which gives us a
true NMI (ie. is not masked by MSR[EE]=0) for debugging etc.
- Support for Power9 DD2 in the CXL driver.
- Improvements to machine check handling so that uncorrectable errors
can be reported into the generic memory_failure() machinery.
- Some fixes and improvements for VPHN, which is used under PowerVM
to notify the Linux partition of topology changes.
- Plumbing to enable TM (transactional memory) without suspend on
some Power9 processors (PPC_FEATURE2_HTM_NO_SUSPEND).
- Support for emulating vector loads form cache-inhibited memory, on
some Power9 revisions.
- Disable the fast-endian switch "syscall" by default (behind a
CONFIG), we believe it has never had any users.
- A major rework of the API drivers use when initiating and waiting
for long running operations performed by OPAL firmware, and changes
to the powernv_flash driver to use the new API.
- Several fixes for the handling of FP/VMX/VSX while processes are
using transactional memory.
- Optimisations of TLB range flushes when using the radix MMU on
Power9.
- Improvements to the VAS facility used to access coprocessors on
Power9, and related improvements to the way the NX crypto driver
handles requests.
- Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew
Donnellan, Aneesh Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin
Herrenschmidt, Breno Leitao, Christophe Leroy, Christophe Lombard,
Cyril Bur, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven,
Guilherme G. Piccoli, Gustavo Romero, Haren Myneni, Joel Stanley,
Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami Hiramatsu,
Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia
Franco de Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee,
Shriya, Stephen Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel
Datwyler, Vaibhav Jain, Vaidyanathan Srinivasan, and William A.
Kennington III"
* tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (151 commits)
powerpc/64s: Fix Power9 DD2.0 workarounds by adding DD2.1 feature
powerpc/64s: Fix masking of SRR1 bits on instruction fault
powerpc/64s: mm_context.addr_limit is only used on hash
powerpc/64s/radix: Fix 128TB-512TB virtual address boundary case allocation
powerpc/64s/hash: Allow MAP_FIXED allocations to cross 128TB boundary
powerpc/64s/hash: Fix fork() with 512TB process address space
powerpc/64s/hash: Fix 128TB-512TB virtual address boundary case allocation
powerpc/64s/hash: Fix 512T hint detection to use >= 128T
powerpc: Fix DABR match on hash based systems
powerpc/signal: Properly handle return value from uprobe_deny_signal()
powerpc/fadump: use kstrtoint to handle sysfs store
powerpc/lib: Implement UACCESS_FLUSHCACHE API
powerpc/lib: Implement PMEM API
powerpc/powernv/npu: Don't explicitly flush nmmu tlb
powerpc/powernv/npu: Use flush_all_mm() instead of flush_tlb_mm()
powerpc/powernv/idle: Round up latency and residency values
powerpc/kprobes: refactor kprobe_lookup_name for safer string operations
powerpc/kprobes: Blacklist emulate_update_regs() from kprobes
powerpc/kprobes: Do not disable interrupts for optprobes and kprobes_on_ftrace
powerpc/kprobes: Disable preemption before invoking probe handler for optprobes
...
Most callers users of free_hot_cold_page claim the pages being released
are cache hot. The exception is the page reclaim paths where it is
likely that enough pages will be freed in the near future that the
per-cpu lists are going to be recycled and the cache hotness information
is lost. As no one really cares about the hotness of pages being
released to the allocator, just ditch the parameter.
The APIs are renamed to indicate that it's no longer about hot/cold
pages. It should also be less confusing as there are subtle differences
between them. __free_pages drops a reference and frees a page when the
refcount reaches zero. free_hot_cold_page handled pages whose refcount
was already zero which is non-obvious from the name. free_unref_page
should be more obvious.
No performance impact is expected as the overhead is marginal. The
parameter is removed simply because it is a bit stupid to have a useless
parameter copied everywhere.
[mgorman@techsingularity.net: add pages to head, not tail]
Link: http://lkml.kernel.org/r/20171019154321.qtpzaeftoyyw4iey@techsingularity.net
Link: http://lkml.kernel.org/r/20171018075952.10627-8-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a machine with 5-level paging support a process can allocate
significant amount of memory and stay unnoticed by oom-killer and memory
cgroup. The trick is to allocate a lot of PUD page tables. We don't
account PUD page tables, only PMD and PTE.
We already addressed the same issue for PMD page tables, see commit
dc6c9a35b6 ("mm: account pmd page tables to the process").
Introduction of 5-level paging brings the same issue for PUD page
tables.
The patch expands accounting to PUD level.
[kirill.shutemov@linux.intel.com: s/pmd_t/pud_t/]
Link: http://lkml.kernel.org/r/20171004074305.x35eh5u7ybbt5kar@black.fi.intel.com
[heiko.carstens@de.ibm.com: s390/mm: fix pud table accounting]
Link: http://lkml.kernel.org/r/20171103090551.18231-1-heiko.carstens@de.ibm.com
Link: http://lkml.kernel.org/r/20171002080427.3320-1-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Radix keeps no meaningful state in addr_limit, so remove it from radix
code and rename to slb_addr_limit to make it clear it applies to hash
only.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Radix VA space allocations test addresses against mm->task_size which
is 512TB, even in cases where the intention is to limit allocation to
below 128TB.
This results in mmap with a hint address below 128TB but address +
length above 128TB succeeding when it should fail (as hash does after
the previous patch).
Set the high address limit to be considered up front, and base
subsequent allocation checks on that consistently.
Fixes: f4ea6dcb08 ("powerpc/mm: Enable mappings above 128TB")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
While mapping hints with a length that cross 128TB are disallowed,
MAP_FIXED allocations that cross 128TB are allowed. These are failing
on hash (on radix they succeed). Add an additional case for fixed
mappings to expand the addr_limit when crossing 128TB.
Fixes: f4ea6dcb08 ("powerpc/mm: Enable mappings above 128TB")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Hash unconditionally resets the addr_limit to default (128TB) when the
mm context is initialised. If a process has > 128TB mappings when it
forks, the child will not get the 512TB addr_limit, so accesses to
valid > 128TB mappings will fail in the child.
Fix this by only resetting the addr_limit to default if it was 0. Non
zero indicates it was duplicated from the parent (0 means exec()).
Fixes: f4ea6dcb08 ("powerpc/mm: Enable mappings above 128TB")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When allocating VA space with a hint that crosses 128TB, the SLB
addr_limit variable is not expanded if addr is not > 128TB, but the
slice allocation looks at task_size, which is 512TB. This results in
slice_check_fit() incorrectly succeeding because the slice_count
truncates off bit 128 of the requested mask, so the comparison to the
available mask succeeds.
Fix this by using mm->context.addr_limit instead of mm->task_size for
testing allocation limits. This causes such allocations to fail.
Fixes: f4ea6dcb08 ("powerpc/mm: Enable mappings above 128TB")
Cc: stable@vger.kernel.org # v4.12+
Reported-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently userspace is able to request mmap() search between 128T-512T
by specifying a hint address that is greater than 128T. But that means
a hint of 128T exactly will return an address below 128T, which is
confusing and wrong.
So fix the logic to check the hint is greater than *or equal* to 128T.
Fixes: f4ea6dcb08 ("powerpc/mm: Enable mappings above 128TB")
Cc: stable@vger.kernel.org # v4.12+
Suggested-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of Nick's bigger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When using the radix MMU on Power9 DD1, to work around a hardware
problem, radix__pte_update() is required to do a two stage update of
the PTE. First we write a zero value into the PTE, then we flush the
TLB, and then we write the new PTE value.
In the normal case that works OK, but it does not work if we're
updating the PTE that maps the code we're executing, because the
mapping is removed by the TLB flush and we can no longer execute from
it. Unfortunately the STRICT_RWX code needs to do exactly that.
The exact symptoms when we hit this case vary, sometimes we print an
oops and then get stuck after that, but I've also seen a machine just
get stuck continually page faulting with no oops printed. The variance
is presumably due to the exact layout of the text and the page size
used for the mappings. In all cases we are unable to boot to a shell.
There are possible solutions such as creating a second mapping of the
TLB flush code, executing from that, and then jumping back to the
original. However we don't want to add that level of complexity for a
DD1 work around.
So just detect that we're running on Power9 DD1 and refrain from
changing the permissions, effectively disabling STRICT_RWX on Power9
DD1.
Fixes: 7614ff3272 ("powerpc/mm/radix: Implement STRICT_RWX/mark_rodata_ro() for Radix")
Cc: stable@vger.kernel.org # v4.13+
Reported-by: Andrew Jeffery <andrew@aj.id.au>
[Changelog as suggested by Michael Ellerman <mpe@ellerman.id.au>]
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Unmaps that free page tables always flush the entire PID, which is
sub-optimal. Provide TLB range flushing with an additional PWC flush
that can be use for va range invalidations with PWC flush.
Time to munmap N pages of memory including last level page table
teardown (after mmap, touch), local invalidate:
N 1 2 4 8 16 32 64
vanilla 3.2us 3.3us 3.4us 3.6us 4.1us 5.2us 7.2us
patched 1.4us 1.5us 1.7us 1.9us 2.6us 3.7us 6.2us
Global invalidate:
N 1 2 4 8 16 32 64
vanilla 2.2us 2.3us 2.4us 2.6us 3.2us 4.1us 6.2us
patched 2.1us 2.5us 3.4us 5.2us 8.7us 15.7us 6.2us
Local invalidates get much better across the board. Global ones have
the same issue where multiple tlbies for va flush do get slower than
the single tlbie to invalidate the PID. None of this test captures
the TLB benefits of avoiding killing everything.
Global gets worse, but it is brought in to line with global invalidate
for munmap()s that do not free page tables.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The single page flush ceiling is the cut-off point at which we switch
from invalidating individual pages, to invalidating the entire process
address space in response to a range flush.
Introduce a local variant of this heuristic because local and global
tlbie have significantly different properties:
- Local tlbiel requires 128 instructions to invalidate a PID, global
tlbie only 1 instruction.
- Global tlbie instructions are expensive broadcast operations.
The local ceiling has been made much higher, 2x the number of
instructions required to invalidate the entire PID (i.e., 256 pages).
Time to mprotect N pages of memory (after mmap, touch), local invalidate:
N 32 34 64 128 256 512
vanilla 7.4us 9.0us 14.6us 26.4us 50.2us 98.3us
patched 7.4us 7.8us 13.8us 26.4us 51.9us 98.3us
The behaviour of both is identical at N=32 and N=512. Between there,
the vanilla kernel does a PID invalidate and the patched kernel does
a va range invalidate.
At N=128, these require the same number of tlbiel instructions, so
the patched version can be sen to be cheaper when < 128, and more
expensive when > 128. However this does not well capture the cost
of invalidated TLB.
The additional cost at 256 pages does not seem prohibitive. It may
be the case that increasing the limit further would continue to be
beneficial to avoid invalidating all of the process's TLB entries.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently for radix, flush_tlb_range flushes the entire PID, because
the Linux mm code does not tell us about page size here for THP vs
regular pages. This is quite sub-optimal for small mremap / mprotect
/ change_protection.
So implement va range flushes with two flush passes, one for each
page size (regular and THP). The second flush has an order of matnitude
fewer tlbie instructions than the first, so it is a relatively small
additional cost.
There is still room for improvement here with some changes to generic
APIs, particularly if there are mostly THP pages to be invalidated,
the small page flushes could be reduced.
Time to mprotect 1 page of memory (after mmap, touch):
vanilla 2.9us 1.8us
patched 1.2us 1.6us
Time to mprotect 30 pages of memory (after mmap, touch):
vanilla 8.2us 7.2us
patched 6.9us 17.9us
Time to mprotect 34 pages of memory (after mmap, touch):
vanilla 9.1us 8.0us
patched 9.0us 8.0us
34 pages is the point at which the invalidation switches from va
to entire PID, which tlbie can do in a single instruction. This is
why in the case of 30 pages, the new code runs slower for this test.
This is a deliberate tradeoff already present in the unmap and THP
promotion code, the idea is that the benefit from avoiding flushing
entire TLB for this PID on all threads in the system.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the barriers and range iteration down into the _tlbie* level,
which improves readability.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Short range flushes issue a sequences of tlbie(l) instructions for
individual effective addresses. These do not all require individual
barrier sequences, only one covering all tlbie(l) instructions.
Commit f7327e0ba3 ("powerpc/mm/radix: Remove unnecessary ptesync")
made a similar optimization for tlbiel for PID flushing.
For tlbie, the ISA says:
The tlbsync instruction provides an ordering function for the
effects of all tlbie instructions executed by the thread executing
the tlbsync instruction, with respect to the memory barrier
created by a subsequent ptesync instruction executed by the same
thread.
Time to munmap 30 pages of memory (after mmap, touch):
local global
vanilla 10.9us 22.3us
patched 3.4us 14.4us
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have some dependencies & conflicts between patches in fixes and
things to go in next, both in the radix TLB flush code and the IMC PMU
driver. So merge fixes into next.
In commit e6f81a9201 ("powerpc/mm/hash: Support 68 bit VA") the
masking is folded into ASM_VSID_SCRAMBLE but the comment about masking
is removed only from the firt use of ASM_VSID_SCRAMBLE.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently if the hardware supports the radix MMU we will use
it, *unless* "disable_radix" is passed on the kernel command line.
However some users would like the reverse semantics. ie. The kernel
uses the hash MMU by default, unless radix is explicitly requested on
the command line.
So add a CONFIG option to choose whether we use radix by default or
not, and expand the disable_radix command line option to allow
"disable_radix=no" which *enables* radix.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_PPC_STD_MMU_64 indicates support for the "standard" powerpc MMU
on 64-bit CPUs. The "standard" MMU refers to the hash page table MMU
found in "server" processors, from IBM mainly.
Currently CONFIG_PPC_STD_MMU_64 is == CONFIG_PPC_BOOK3S_64. While it's
annoying to have two symbols that always have the same value, it's not
quite annoying enough to bother removing one.
However with the arrival of Power9, we now have the situation where
CONFIG_PPC_STD_MMU_64 is enabled, but the kernel is running using the
Radix MMU - *not* the "standard" MMU. So it is now actively confusing
to use it, because it implies that code is disabled or inactive when
the Radix MMU is in use, however that is not necessarily true.
So s/CONFIG_PPC_STD_MMU_64/CONFIG_PPC_BOOK3S_64/, and do some minor
formatting updates of some of the affected lines.
This will be a pain for backports, but c'est la vie.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
According to the architecture, the process table entry cache must be
flushed with tlbie RIC=2.
Currently the process table entry is set to invalid right before the
PID is returned to the allocator, with no invalidation. This works on
existing implementations that are known to not cache the process table
entry for any except the current PIDR.
It is architecturally correct and cleaner to invalidate with RIC=2
after clearing the process table entry and before the PID is returned
to the allocator. This can be done in arch_exit_mmap that runs before
the final flush, and to ensure the final flush (fullmm) is always a
RIC=2 variant.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Preempt should be consistently disabled for mm_is_thread_local tests,
so bring the rest of these under preempt_disable().
Preempt does not need to be disabled for the mm->context.id tests,
which allows simplification and removal of gotos.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A fix to the handling of misaligned paste instructions (P9 only), where a change
to a #define has caused the check for the instruction to always fail.
The preempt handling was unbalanced in the radix THP flush (P9 only). Though we
don't generally use preempt we want to keep it working as much as possible.
Two fixes for IMC (P9 only), one when booting with restricted number of CPUs and
one in the error handling when initialisation fails due to firmware etc.
A revert to fix function_graph on big endian machines, and then a rework of the
reverted patch to fix kprobes blacklist handling on big endian machines.
Thanks to:
Anju T Sudhakar, Guilherme G. Piccoli, Madhavan Srinivasan, Naveen N. Rao,
Nicholas Piggin, Paul Mackerras.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vTi1
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.14-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 4.14.
This is bigger than I like to send at rc7, but that's at least partly
because I didn't send any fixes last week. If it wasn't for the IMC
driver, which is new and getting heavy testing, the diffstat would
look a bit better. I've also added ftrace on big endian to my test
suite, so we shouldn't break that again in future.
- A fix to the handling of misaligned paste instructions (P9 only),
where a change to a #define has caused the check for the
instruction to always fail.
- The preempt handling was unbalanced in the radix THP flush (P9
only). Though we don't generally use preempt we want to keep it
working as much as possible.
- Two fixes for IMC (P9 only), one when booting with restricted
number of CPUs and one in the error handling when initialisation
fails due to firmware etc.
- A revert to fix function_graph on big endian machines, and then a
rework of the reverted patch to fix kprobes blacklist handling on
big endian machines.
Thanks to: Anju T Sudhakar, Guilherme G. Piccoli, Madhavan Srinivasan,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras"
* tag 'powerpc-4.14-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/perf: Fix core-imc hotplug callback failure during imc initialization
powerpc/kprobes: Dereference function pointers only if the address does not belong to kernel text
Revert "powerpc64/elfv1: Only dereference function descriptor for non-text symbols"
powerpc/64s/radix: Fix preempt imbalance in TLB flush
powerpc: Fix check for copy/paste instructions in alignment handler
powerpc/perf: Fix IMC allocation routine
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 424de9c6e3 ("powerpc/mm/radix: Avoid flushing the PWC on every flush_tlb_range")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We call these functions with non-NULL mm or vma. Hence we can skip the
NULL check in these functions. We also remove now unused function
__local_flush_hugetlb_page().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Drop the checks with is_vm_hugetlb_page() as noticed by Nick]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/vphn: On Power systems with shared configurations of CPUs
and memory, there are some issues with the association of additional
CPUs and memory to nodes when hot-adding resources. This patch
fixes an end-of-updates processing problem observed occasionally
in numa_update_cpu_topology().
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/hotplug: On Power systems with shared configurations of CPUs
and memory, there are some issues with the association of additional
CPUs and memory to nodes when hot-adding resources. During hotplug
CPU operations, this patch resets the timer on topology update work
function to a small value to better ensure that the CPU topology is
detected and configured sooner.
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/vphn: On Power systems with shared configurations of CPUs
and memory, there are some issues with the association of additional
CPUs and memory to nodes when hot-adding resources. This patch
updates the initialization checks to independently recognize PRRN
or VPHN support.
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/vphn: On Power systems with shared configurations of CPUs
and memory, there are some issues with the association of additional
CPUs and memory to nodes when hot-adding resources. This patch
corrects the currently broken capability to set the topology for
shared CPUs in LPARs. At boot time for shared CPU lpars, the
topology for each CPU was being set to node zero. Now when
numa_update_cpu_topology() is called appropriately, the Virtual
Processor Home Node (VPHN) capabilities information provided by the
pHyp allows the appropriate node in the shared configuration to be
selected for the CPU.
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It turns out that not all paths calling arch_update_cpu_topology() hold
cpu_hotplug_lock, but that's OK because those paths can't race with
any concurrent hotplug events.
Warnings were reported with the following trace:
lockdep_assert_cpus_held
arch_update_cpu_topology
sched_init_domains
sched_init_smp
kernel_init_freeable
kernel_init
ret_from_kernel_thread
Which is safe because it's called early in boot when hotplug is not
live yet.
And also this trace:
lockdep_assert_cpus_held
arch_update_cpu_topology
partition_sched_domains
cpuset_update_active_cpus
sched_cpu_deactivate
cpuhp_invoke_callback
cpuhp_down_callbacks
cpuhp_thread_fun
smpboot_thread_fn
kthread
ret_from_kernel_thread
Which is safe because it's called as part of CPU hotplug, so although
we don't hold the CPU hotplug lock, there is another thread driving
the CPU hotplug operation which does hold the lock, and there is no
race.
Thanks to tglx for deciphering it for us.
Fixes: 3e401f7a2e ("powerpc: Only obtain cpu_hotplug_lock if called by rtasd")
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The PSL and nMMU need to see all TLB invalidations for the memory
contexts used on the adapter. For the hash memory model, it is done by
making all TLBIs global as soon as the cxl driver is in use. For
radix, we need something similar, but we can refine and only convert
to global the invalidations for contexts actually used by the device.
The new mm_context_add_copro() API increments the 'active_cpus' count
for the contexts attached to the cxl adapter. As soon as there's more
than 1 active cpu, the TLBIs for the context become global. Active cpu
count must be decremented when detaching to restore locality if
possible and to avoid overflowing the counter.
The hash memory model support is somewhat limited, as we can't
decrement the active cpus count when mm_context_remove_copro() is
called, because we can't flush the TLB for a mm on hash. So TLBIs
remain global on hash.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Fixes: f24be42aab ("cxl: Add psl9 specific code")
Tested-by: Alistair Popple <alistair@popple.id.au>
[mpe: Fold in updated comment on the barrier from Fred]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the optimizations introduced by commit a46cc7a90f
("powerpc/mm/radix: Improve TLB/PWC flushes"), flush_tlb_mm() no
longer flushes the page walk cache (PWC) with radix. This patch
introduces flush_all_mm(), which flushes everything, TLB and PWC, for
a given mm.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-By: Alistair Popple <alistair@popple.id.au>
[mpe: Add a WARN_ON_ONCE() in the empty hash routines]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Two single characters (line breaks) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 9445aa1a30 ("ppc: move exports to definitions")
added EXPORT_SYMBOL() for memset() and flush_hash_pages() in
the middle of the functions.
This patch moves them at the end of the two functions.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we map memory at boot we print out the ranges of real addresses
that we mapped and the page size that was used.
Currently it's a bit ugly:
Mapped range 0x0 - 0x2000000000 with 0x40000000
Mapped range 0x200000000000 - 0x202000000000 with 0x40000000
Pad the addresses so they line up, and print the page size using
actual units, eg:
Mapped 0x0000000000000000-0x0000000001200000 with 64.0 KiB pages
Mapped 0x0000000001200000-0x0000000040000000 with 2.00 MiB pages
Mapped 0x0000000040000000-0x0000000100000000 with 1.00 GiB pages
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It's too big to be inline, there is no reason to keep it
that way.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Rework to incorporate the comment changes via fixes branch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of comparing the whole CPU mask every time, let's
keep a counter of how many bits are set in the mask. Thus
testing for a local mm only requires testing if that counter
is 1 and the current CPU bit is set in the mask.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We open-code testing for the mm being local to the current CPU
in a few places. Use our existing helper instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's a non-trivial dependency between some commits we want to put in
next and the KVM prefetch work around that went into fixes. So merge
fixes into next.
We use mm cpumask for serializing against lockless page table walk.
Anybody who is doing a lockless page table walk is expected to disable
irq and only cpus in mm cpumask is expected do the lockless walk. This
ensure that a THP split can send IPI to only cpus in the mm cpumask,
to make sure there are no parallel lockless page table walk.
Add the CAPI fault handling cpu to the mm cpumask so that we can do
the lockless page table walk while inserting hash page table entries.
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we made sure that lockless walk of linux page table is mostly
limitted to current task(current->mm->pgdir) we can update the THP
update sequence to only send IPI to CPUs on which this task has run.
This helps in reducing the IPI overload on systems with large number
of CPUs.
WRT kvm even though kvm is walking page table with vpc->arch.pgdir,
it is done only on secondary CPUs and in that case we have primary CPU
added to task's mm cpumask. Sending an IPI to primary will force the
secondary to do a vm exit and hence this mm cpumask usage is safe
here.
WRT CAPI, we still end up walking linux page table with capi context
MM. For now the pte lookup serialization sends an IPI to all CPUs in
CPI is in use. We can further improve this by adding the CAPI
interrupt handling CPU to task mm cpumask. That will be done in a
later patch.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Linus Torvalds