This patch adds support to set the power line polarity for i.MX SoCs.
To let the USB controller control the power it may be necessary to
configure the polarity of the power line. So far the polarity was
configured by Bootloader or alternatively the power line was muxed
as gpio and driven by a regulator.
Also make use of of_property_read_bool.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Up to now the polarity of the over current pin was hard coded to active
high. Use the already defined device tree properties to configure polarity
on i.MX25, too. In difference to i.MX6/7 use active high behavior if the
polarity is unspecified to keep compatibility to existing device trees.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The status quo on i.MX6 is that if "over-current-active-high" is
specified in the device tree this is configured as expected. If
the property is missing polarity isn't changed and so the
polarity is kept as setup by the bootloader. Reset default is
active high, so active low can only be used with help by the
bootloader. On i.MX7 it is similar, but there disabling of
over current detection has a similar inconsistency.
This patch introduces a new property that allows to explicitly
configure for active low over current detection and consistently
sets this up. In the absence of an explicit configuration the
bit is kept as is. On i.MX7 over current detection is used unless
disabled in the device tree.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
To support imx HSIC, there are some special requirement:
- The HSIC pad is 1.2v, it may need to supply from external
- The data/strobe pin needs to be pulled down first, and after
host mode is initialized, the strobe pin needs to be pulled up
- During the USB suspend/resume, special setting is needed
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The SPDX-License-Identifier is set to GPL-2.0+, which correspond to
MODULE_LICENSE "GPL".
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
When initializing the USB subsystem before starting the kernel,
OTG overcurrent detection is disabled. In case the OTG polarity of
overcurrent is low active, the overcurrent detection is never enabled
again and events cannot be reported as expected. Because imx usb
overcurrent polarity is low active by default, only detection needs
to be enable in usbmisc init function.
Signed-off-by: Nicolas Adell <nicolas.adell@actia.fr>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The register write can be done outside the if and else condition
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
evdo bit can be set or reset. We can not trust evdo bit
status after bootloader stage
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB_PHY_CTRL_FUNC is used specific for OTG port as described
in user manual. EVDO need to be set only for index 0 that
correspond to OTG port
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike i.MX53, i.MX51's USBOH3 register file does not implemenent
registers past offset 0x018, which includes
MX53_USB_CLKONOFF_CTRL_OFFSET and trying to access that register on
said platform results in external abort.
Fix it by enabling CLKONOFF accessing codepath only for i.MX53.
Cc: stable <stable@vger.kernel.org>
Fixes 3be3251db0 ("usb: chipidea: imx: Disable internal 60Mhz
clock with ULPI PHY")
Cc: cphealy@gmail.com
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The internal 60Mhz clock for host2 and host3 are useless in ULPI
phy mode, so we disable it when configuring ULPI PHY node for
those host.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In order to use ULPI phy with usb host 2 and 3, we need to configure
controller register to enable ULPI features.
Each USB controller have different behaviour, so in order to avoid to have
several "swicth(data->index)" and lock/unlock, we prefer to get the index
switch and then test for features if they exist for this index.
This patch also remove useless test of reg and val. Those two values cannot
be NULL.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
imx usb over current polarity is low active by default, with
over-current-active-high property added, user can config it to be high
active. Meanwhile keep this setting unchanged for existing platforms
so new platform must set the right value for active low by its usbmisc
init function if over current is enabled.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later. Renaming tmp_dev to of_id (like all others do) in the
process.
Reported-by: coverity (CID 1324135)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Add imx6ul usb support.
Signed-off-by: Peter chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
With this setting and AHBBRST at SBUSCFG as "Incremental burst of
unspecified length", each non-burst size can be taken as single
transfer. It is benefit for non-burst size transfer.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Remove unneeded semicolon.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/semicolon.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Except the same process with earlier imx6, it has below two features:
- Choose which vbus voltage as vbus wakeup source
We choose B_SESSION_VALID as vbus wakeup source since when the system
goes to suspend, the vbus comparator can't compare the vbus voltage
for VBUS_VALID.
- Disable dp/dm (linestate) change as wakeup source at device mode
when the vbus is not there, we don't expect dp/dm change waking up
usb controller at this situation.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This API is used to enable/disable usb wakeup, only imx6 series are
added, since I don't have other imx hardware on hand. Other imx users
can add their API according to reference manual after testing.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move struct imx_usbmisc_data NULL pointer judgement from caller to
each API, it can simplify the caller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All imx usb controller's non core registers uses the same clock gate with
core registers, the usbmisc_imx is the library for imx glue driver, the
glue keeps clock on when it calls usbmisc_imx API to change non-core register.
Besides, we will support runtime pm in the future, it also needs to
close this clock when the usb is not in use.
Philipp Zabel also verifies it at imx6q platform, see
http://www.spinics.net/lists/linux-usb/msg118491.html
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
There is no need to do an intermediate step for reading the
MX53_USB_OTG_PHY_CTRL_1_OFFSET register.
Read it directly instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If 'evdo' property is not defined, then reading the MX25_USB_PHY_CTRL_OFFSET
register is an unneeded operation.
Move the reading of MX25_USB_PHY_CTRL_OFFSET inside the 'evdo' if block code,
where it is actually used.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds Vybrid VF610 SoC support. The IP is very similar to i.MX6,
however, the non-core registers are spread in two different register
areas. Hence we support multiple instances of the USB misc driver
and add the driver instance to the imx_usbmisc_data structure.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The field PLLDIVVALUE of register PHY_CTRL_1 selects the reference clock source
for the PHY:
00 = sysclock uses 19.2 MHz
01 = sysclock uses 24 MHz
10 = sysclock uses 26 MHz
11 = sysclock uses 27 MHz
The reset value for this field is 10 according to the reference manual, and
even though this reset value works for mx53, it does not work for mx51.
So instead of relying on the reset value for the PLLDIVVALUE field, explicitly
set it to 01 so that a 24MHz clock can be selected for the PHY and allowing both
mx51 and mx53 to have USB OTG port functional.
Succesfully tested 'g_ether' on a imx51-babbage and on a imx53-qsb boards.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the i.MX25 and the i.MX35 support in the
ChipIdea usbmisc driver.
The i.MX25 and i.MX35 usb controllers are similar enough to be
able to use the same code.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds i.MX51 as the next user of the usbmisc driver.
Functionality is similar to i.MX53, so at this stage simply
reuse existing i.MX53 calls.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds i.MX27 and i.MX31 as the next user of the usbmisc driver.
Tested-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chipidea i.MX driver is split into two drivers. The ci_hdrc_imx driver
handles the chipidea cores and the usbmisc_imx driver handles the noncore
registers common to all chipidea cores (but SoC specific). Current flow is:
- usbmisc sets an ops pointer in the ci_hdrc_imx driver during probe
- ci_hdrc_imx checks if the pointer is valid during probe, if yes calls
the functions in the ops pointer.
- usbmisc_imx calls back into the ci_hdrc_imx driver to get additional
data
This is overly complicated and has problems if the drivers are compiled
as modules. In this case the usbmisc_imx driver can be unloaded even if
the ci_hdrc_imx driver still needs usbmisc functionality.
This patch changes this by letting the ci_hdrc_imx driver calling functions
from the usbmisc_imx driver. This way the symbol resolving during module
load makes sure the ci_hdrc_imx driver depends on the usbmisc_imx driver.
Also instead of letting the usbmisc_imx driver call back into the ci_hdrc_imx
driver, pass the needed data in the first place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"ci13xxx" is bad for at least the following reasons:
* people often mistype it
* it doesn't add any informational value to the names it's used in
* it needlessly attracts mail filters
This patch replaces it with "ci_hdrc", "ci_udc" or "ci_hw", depending
on the situation. Modules with ci13xxx prefix are also renamed accordingly
and aliases are added for compatibility. Otherwise, no functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow udev to autoload the module when booting with device-tree
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts the driver to use the module_platform_driver
macro which makes the code smaller and a bit simpler.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following sparse warnings:
drivers/usb/chipidea/usbmisc_imx.c:246:5: warning: symbol 'usbmisc_imx_drv_init' was not declared. Should it be static?
drivers/usb/chipidea/usbmisc_imx.c:252:6: warning: symbol 'usbmisc_imx_drv_exit' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a post handling routine which is called after
ci13xxx_add_device was called. The first user is the mx25, which has to
disable the external-vbus-divider after the udc has started.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[Alex: also fixed a signed one-bit bitfield a whitespace error and yet
another set of line-too-long and void pointer casting errors]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds mx53 as the next user of the usbmisc driver and makes it
possible to disable the overcurrent-detection of the internal phy.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[Alex: fixed another set of line-too-long and void pointer cast]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This attaches the usbmisc_ops to the of_device_id data and
makes it possible to define special functions per soc.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
[Alex: fixed one case of line-too-long and one bogus cast to void ptr]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a potential race condition where the ci13xxx_imx glue code
could be fast enough to call one of the usbmisc_ops before he got a
valid value on the static usbmisc pointer. To fix that we first set
usbmisc, then call usbmisc_set_ops().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe function checks usbmisc to be NULL in the beginning. Without
this patch the can only be loaded once.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver will be used for every Freescale SoC which has this misc
memory layout to control the basic usb handling. So better name this
driver, function and struct names in a more generic way.
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Philipp Puschmann