changes for reemoteproc platform_data and audio options for
omap2plus_defconfig to keep audio working when changing boards
to use SIMPLE_CARD. The summary of changes is:
- A large set of audio related changes for SIMPLE_CARD from
Peter Ujfalusi <peter.ujfalusi@ti.com> for am335x and am437x
- Pinctrl dts defines for dra7 virtual mode to configure timings
- Change to use cpsw slave0 for dra7 Ethernet
- Remove unconfigured and wrong l3-mux entry for dm816x
- Add support for Gumstix Palo35 and TobiDuo boards, and Overo
PoP NAND and McBSP2
- Start using new HDMI binding for tilcdc
- Start using new sDMA crossbar for dra7
- Start using rproc for am335x and am437x M3 coprocessor
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sPfQ
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.3/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v4.3, part 1" from Tony Lindgren:
Omap dts changes for v4.3 merge window. There are also related
changes for reemoteproc platform_data and audio options for
omap2plus_defconfig to keep audio working when changing boards
to use SIMPLE_CARD. The summary of changes is:
- A large set of audio related changes for SIMPLE_CARD from
Peter Ujfalusi <peter.ujfalusi@ti.com> for am335x and am437x
- Pinctrl dts defines for dra7 virtual mode to configure timings
- Change to use cpsw slave0 for dra7 Ethernet
- Remove unconfigured and wrong l3-mux entry for dm816x
- Add support for Gumstix Palo35 and TobiDuo boards, and Overo
PoP NAND and McBSP2
- Start using new HDMI binding for tilcdc
- Start using new sDMA crossbar for dra7
- Start using rproc for am335x and am437x M3 coprocessor
* tag 'omap-for-v4.3/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (32 commits)
ARM: dts: am335x-evm: Switch using simple-audio-card for audio support
ARM: dts: am335x-evm: Add sleep pin settings for mcasp1
ARM: dts: am335x-evm: Rename pinctrl section for McASP1
ARM: dts: am335x-evm: Fix mcasp1 node's indentation
ARM: dts: am335x-evmsk: Switch using simple-audio-card for audio support
ARM: dts: am335x-evmsk: Add sleep pin settings for mcasp1
ARM: dts: am335x-evmsk: Fix mcasp1 node's indentation
ARM: dts: am437x-gp-evm: Enable analog audio via simple-card
ARM: dts: am437x-gp-evm: McASP1 node for audio support
ARM: dts: am437x-gp-evm: Add node for tlv320aic3106 audio codec
ARM: dts: am437x-gp-evm: Rename fixed regulator vmmcsd_fixed to evm_v3_3d
ARM: dts: am437x-gp-evm: Add gpio-hog for configuring the display/audio mux
ARM: dts: am43xx-epos-evm: Enable analog audio via simple-card
ARM: dts: am43xx-epos-evm: Add node for tlv320aic3111 audio codec
ARM: dts: am43xx-epos-evm: McASP1 node for audio support
ARM: dts: am43xx-epos-evm: Add regulator for VBAT and DCDC4 of tps65218
ARM: dts: am43xx-epos-evm: Add gpio-hog for configuring the display/audio mux
ARM: dts: am437x-sk-evm: Switch using simple-audio-card for audio support
ARM: dts: am437x-sk-evm: Add sleep pin settings for mcasp1
ARM: omap2plus_defconfig: Enable audio related config options
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch creates a sbs-battery fragment for batteries connected
to the i2c tunnel of the cros-ec embedded controller.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Douglas Anderson <dianders@chromium.org>
It is easy to modify settings for Test or other purpose if sound has label
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
It is easy to modify settings for Test or other purpose if sound has label
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This board is used in some TV-boxes like for example the Beelink R89 or
Tronsmart R28.
The board itself follows the reference design for the most part. But
there are no schematics available it seems, so some things should be
taken with a grain of salt.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Romain Perier <romain.perier@gmail.com>
Add basic support for CIAA (Argentine Open Industrial Computer)
LPC4337 board. This commit enables the following peripherals:
* UART
* SSP
* Ethernet
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
CIAA stands for Argentine Open Industrial Computer. The CIAA project
is an initiative sponsored by universities and private companies.
Its main goal is to promote local embedded systems development.
Among other devices, the project developed a NXP LPC4337-based
reference design.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
The sound support consist only Headset output on the board and can be
handled by "simple-audio-card"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use mcasp1_pins as name for the pinctrl section needed for McASP1 instead
of the am335x_evm_audio_pins name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sound support consist only Headset output on the board and can be
handled by "simple-audio-card"
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses McASP1 <-> tlv320aic3106 for analog audio and has
Headphone out and Line in connectors.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node for McASP1 along with the needed pinctrl entries.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The same regulator is used by other chips on the board. The power path is:
VBAT -> TPS63031 - Enable signal is V1_8D regulator -> V3_3D.
V3_3D is used by SD slot and tlv320aic3106 codec as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO5_8 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use simple card for audio support on ePOS-EVM.
The audio on the board is: McASP1 <-> tlv320aic3111 codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node for McASP1 along with the needed pinctrl entries.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VBAT and DCDC4 regulator is needed for audio support (tlv320aic3111)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO2_1 is used as a mux switch between LCD and HDMI displays. This mux
affects audio routing as well since in LCD mode HDMI audio is not possible
and when HDMI is selected analog audio is not working.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sound support consist only Headset output on the board and can be
handled by "simple-audio-card".
Also enable the Line-In route as the board has support for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When McASP is not in use the pins can be put to sleep mode to conserve
power.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More and more boards are moving to have audio support via simple-card.
At the same time enable options needed for most am335x and am43xx board for
audio support: McASP and TLV320AIC3X codecs.
The later two has been selected by the CONFIG_SND_AM33XX_SOC_EVM option, but
the aim is to convert all boards to use simple card.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In addition to the regular mux configuration such as mux mode 1,
2 etc, certain pins of DRA7 require to have "virtual mode" also
programmed. This allows for predefined delay characteristics to
be used by the SoC to meet timing characterstics needed for the
interface.
Provide easy to use macro to do the same.
It is important to note that the official TI guidelines recommend
to do as minimal pin reconfiguration beyond the bootloader given
the design of the hardware involved which can result in substantial
glitches which may impair functionality of certain peripherals.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. Add gpio hog entry to pcf_gpio_21 in order to
select cpsw slave0.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The interconnects on dm816x are like on omap4, so we should use
l3-noc instead of l3-smx. But as the related SoC specific
l3_target_data is still missing from omap_l3_noc let's just
remove the entry for now.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Also, reduce the maximum SPI device speed to the max. supported by the
LCD controller used on the LGPhilips LB035Q02 panel for this board.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some Overo COM models include NAND flash in the on-board
package-on-package (PoP) chip. Add this to the base Overo devicetree.
Most commonly, this is 512MB NAND from the Micron MT29C4G96MAZ family
but, as discussed [1], several different sized are possible. To
support different sizes, the last partition should fill to the end of
the chip (i.e. MTDPART_SIZ_FULL).
With thanks to Florian Vaussard for the original patch [2] and Adam Lee for
updating it here.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2013-June/175760.html
[2] http://lists.infradead.org/pipermail/linux-arm-kernel/2013-June/175449.html
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both Gumstix Overo and Overo Storm COMs use TWL4030 audio module
connected to the McBSP2. As such, enable the McBSP2 module in the
common device tree file, omap3-overo-base.dtsi, rather than in the
processor-specific device tree files, omap3-overo.dtsi and
omap3-overo-storm.dtsi. This corrects audio on the Storm COMs where
the setting was accidentally missing from the device tree.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Gumstix "Tobi-Duo" expansion board [1] can be used with either
OMAP3 Overo or Overo Storm COMs. It provides two NICs using LAN9221
chips.
It is necessary to duplicate the interface information for the
second SMSC9221 chip as discussed [2].
[1] https://store.gumstix.com/index.php/products/241/
[2] http://www.spinics.net/lists/linux-omap/msg115282.html
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sDMA requests are routed through the DMA crossbar and without the
crossbar only peripherals using DMA request 0-127 can be used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the Wakeup M3 remote processor device node for
the AM4372 SoC. The WkupM3 remote processor is used
to implement and achieve low-power functionality on
the AM33xx & AM43xx SoCs.
This node is added as a child of the recently added
l4_wkup node to reflect its presence within the SoC.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The WakeupM3 remote processor device node has been moved to
be a child node of the newly created l4_wkup node, to reflect
its presence properly within the SoC. The node was added
previously before any driver support, it is now updated as
per the wkup_m3_rproc bindings added alongside the driver
support.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use pdata-quirks to provide platform data required for reset
management during boot and shutdown of the wkup_m3 processor
on both the AM33xx and AM43xx SoCs. The WkupM3 remote processor
is used to implement and achieve low-power functionality on
the AM33xx & AM43xx SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* Configure IRLM mode via DT on r8a7779 SoC
* Use "arm,gic-400" for GIC on r8a777[01349] and r8a73a4 SoCs
* Add pinctrl and gpio-hog for lcdc0 to armadillo800eva board
* EtherAVB DT support for r8a7790 SoC
* Minimal device tree for r8a7793 SoC and its Gose board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vwn6
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.3" from Simon Horman:
* Configure IRLM mode via DT on r8a7779 SoC
* Use "arm,gic-400" for GIC on r8a777[01349] and r8a73a4 SoCs
* Add pinctrl and gpio-hog for lcdc0 to armadillo800eva board
* EtherAVB DT support for r8a7790 SoC
* Minimal device tree for r8a7793 SoC and its Gose board
* tag 'renesas-dt-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: Configure IRLM mode via DT
ARM: shmobile: r8a7794 dtsi: Use "arm,gic-400" for GIC
ARM: shmobile: r8a7793 dtsi: Use "arm,gic-400" for GIC
ARM: shmobile: r8a7791 dtsi: Use "arm,gic-400" for GIC
ARM: shmobile: r8a7790 dtsi: Use "arm,gic-400" for GIC
ARM: shmobile: r8a73a4 dtsi: Use "arm,gic-400" for GIC
ARM: shmobile: armadillo800eva dts: Add pinctrl and gpio-hog for lcdc0
ARM: shmobile: r8a7790: add EtherAVB DT support
ARM: shmobile: r8a7790: add EtherAVB clocks
ARM: shmobile: r8a7793: add minimal Gose board device tree
ARM: shmobile: add r8a7793 minimal SoC device tree
No dedicated driver compatible with "socionext,uniphier-ehci" has
been supported in the mainline yet, so it falls into "generic-ehci"
and it works well enough with our USB 2.0 host controllers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The UniPhier on-chip UART driver was merged into the mainline by
commit 1a8d2903cb ("serial: 8250_uniphier: add UniPhier serial
driver").
Add device nodes to make it really available.
We no longer have to depend on the on-board UART device (16550A),
so let's change the chosen and aliases to point to the on-chip ones.
Also, turn on the on-board Ethernet device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson