Commit Graph

50 Commits

Author SHA1 Message Date
Ben Hutchings bd68e0838f mmc: add module parameter to set whether cards are assumed removable
Some people run general-purpose distribution kernels on netbooks with
a card that is physically non-removable or logically non-removable
(e.g. used for /home) and cannot be cleanly unmounted during suspend.
Add a module parameter to set whether cards are assumed removable or
non-removable, with the default set by CONFIG_MMC_UNSAFE_RESUME.

In general, it is not possible to tell whether a card present in an MMC
slot after resume is the same that was there before suspend.  So there are
two possible behaviours, each of which will cause data loss in some cases:

CONFIG_MMC_UNSAFE_RESUME=n (default): Cards are assumed to be removed
during suspend.  Any filesystem on them must be unmounted before suspend;
otherwise, buffered writes will be lost.

CONFIG_MMC_UNSAFE_RESUME=y: Cards are assumed to remain present during
suspend.  They must not be swapped during suspend; otherwise, buffered
writes will be flushed to the wrong card.

Currently the choice is made at compile time and this allows that to be
overridden at module load time.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Wouter van Heyst <larstiq@larstiq.dyndns.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:35 -08:00
Nicolas Pitre 95cdfb72b9 mmc: propagate error codes back from bus drivers' suspend/resume methods
Especially for SDIO drivers which may have special conditions/errors to
report, it is a good thing to relay the returned error code back to upper
layers.

This also allows for the rationalization of the resume path where code to
"remove" a no-longer-existing or replaced card was duplicated into the
MMC, SD and SDIO bus drivers.

In the SDIO case, if a function suspend method returns an error, then all
previously suspended functions are resumed and the error returned.  An
exception is made for -ENOSYS which the core interprets as "we don't
support suspend so just kick the card out for suspend and return success".

When resuming SDIO cards, the core code only validates the manufacturer
and product IDs to make sure the same kind of card is still present before
invoking functions resume methods.  It's the function driver's
responsibility to perform further tests to confirm that the actual same
card is present (same MAC address, etc.) and return an error otherwise.

Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:38 -07:00
Denis Karpov 53509f0fe2 mmc: power off once at removal
Fix MMC host stop sequence: power off once.

Signed-off-by: Denis Karpov <ext-denis.2.karpov@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:34 -07:00
Jarkko Lavinen b1ebe38456 mmc: add mmc card sleep and awake support
Add support for the new MMC command SLEEP_AWAKE.

Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:33 -07:00
Adrian Hunter eae1aeeed8 mmc: add ability to save power by powering off cards
Power can be saved by powering off cards that are not in use.  This is
similar to suspend / resume except it is under the control of the driver,
and does not require any power management support.  It can only be used
when the driver can monitor whether the card is removed, otherwise it is
unsafe.  This is possible because, unlike suspend, the driver still
receives card detect and / or cover switch interrupts.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:33 -07:00
Adrian Hunter 319a3f1429 mmc: allow host claim / release nesting
This change allows the MMC host to be claimed in situations where the host
may or may not have already been claimed.  Also 'mmc_try_claim_host()' is
now exported.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:33 -07:00
Adrian Hunter 8ea926b22e mmc: add 'enable' and 'disable' methods to mmc host
MMC hosts that support power saving can use the 'enable' and 'disable'
methods to exit and enter power saving states.  An explanation of their
use is provided in the comments added to include/linux/mmc/host.h.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:33 -07:00
Balaji Rao 500f35648e mmc: in mmc_power_up(), use previously selected ocr if available
When mmc_power_up is called during unsafe resume, host->ocr should be used
instead of host->ocr_avail.

Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:32 -07:00
Sascha Hauer 8dfd0374be MMC core: limit minimum initialization frequency to 400kHz
Some controllers allow a much lower frequency than 400kHz.
Keep the minimum frequency within sensible limits.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2009-06-13 22:42:57 +02:00
Jorg Schummer 94d89efb2c mmc: mmc_rescan detects card change in one run
With this patch, mmc_rescan can detect the removal of an mmc card and
the insertion of (possibly another) card in the same run. This means
that a card change can be detected without having to call
mmc_detect_change multiple times.

This change generalises the core such that it can be easily used by
hosts which provide a mechanism to detect only the presence of a card
reader cover, which has to be taken off in order to insert a card. Other
hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when
a card is removed and when a card is inserted, so it is sufficient for
them if mmc_rescan handles only one event at a time. "Cover detect"
hosts, however, only receive events about the cover status. This means
that between 2 subsequent events, both a card removal and a card
insertion can occur. In this case, the pre-patch version of mmc_rescan
would only detect the removal of the previous card but not the insertion
of the new card.

Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-06-13 22:42:56 +02:00
José M. Fernández 79bccc5aef mmc: increase power up delay
The TI controller on Toshiba Tecra M5 needs more time to power up or
the cards will init incorrectly or not at all.

Signed-off-by: José M. Fernández <josemariafg@gmail.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
2009-05-03 22:11:31 +02:00
Linus Torvalds 0a053e8c71 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (42 commits)
  atmel-mci: fix sdc_reg typo
  tmio_mmc: add maintainer
  mmc: Add OpenFirmware bindings for SDHCI driver
  sdhci: Add quirk for forcing maximum block size to 2048 bytes
  sdhci: Add quirk for controllers that need IRQ re-init after reset
  sdhci: Add quirk for controllers that need small delays for PIO
  sdhci: Add set_clock callback and a quirk for nonstandard clocks
  sdhci: Add get_{max,timeout}_clock callbacks
  sdhci: Add support for hosts reporting inverted write-protect state
  sdhci: Add support for card-detection polling
  sdhci: Enable only relevant (DMA/PIO) interrupts during transfers
  sdhci: Split card-detection IRQs management from sdhci_init()
  sdhci: Add support for bus-specific IO memory accessors
  mmc_spi: adjust for delayed data token response
  omap_hsmmc: Wait for SDBP
  omap_hsmmc: Fix MMC3 dma
  omap_hsmmc: Disable SDBP at suspend
  omap_hsmmc: Do not prefix slot name
  omap_hsmmc: Allow cover switch to cause rescan
  omap_hsmmc: Add 8-bit bus width mode support
  ...
2009-04-05 10:18:21 -07:00
David Brownell 5c13941acc MMC: regulator utilities
Glue between MMC and regulator stacks ... verified with
some OMAP3 boards using adjustable and configured-as-fixed
regulators on several MMC controllers.

These calls are intended to be used by MMC host adapters
using at least one regulator per host.  Examples include
slots with regulators supporting multiple voltages and
ones using multiple voltage rails (e.g. DAT4..DAT7 using a
separate supply, or a split rail chip like certain SDIO
WLAN or eMMC solutions).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2009-03-31 09:56:26 +01:00
Wolfgang Muees c0c8887157 mmc_spi: allow higher timeouts for SPI mode
Some SD cards have very high timeouts in SPI mode.
So adjust the timeouts from theory to practice.

Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2009-03-24 21:30:02 +01:00
Balaji Rao d3096f88ac mmc: During unsafe resume, select the right volatge for the card
During mmc unsafe resume, choose the right voltage for the card after
powerup.

Although this has not seen to cause trouble, it's the wrong behaviour.

Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2009-03-24 21:30:01 +01:00
Jorg Schummer 7de427d088 mmc: delayed_work was never cancelled
The delayed work item mmc_host.detect is now cancelled before flushing
the work queue. This takes care of cases when delayed_work was scheduled
for mmc_host.detect, but not yet placed in the work queue.

Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2009-03-24 21:29:58 +01:00
David Brownell f6e10b865c mmc: warn about voltage mismatches
Get rid of a silent failure mode when the MMC/SD host doesn't
support the voltages needed to operate a given card, by
adding a warning.  A 3.3V host and a 3.0V card, for example,
no longer need to mysteriously just not work at all.

This isn't the best diagnostic; ideally it would also tell
what voltage the card and host support (and not just by
dumping the bitmasks).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-12-31 19:27:18 +01:00
Anton Vorontsov 86e8286a0e mmc: Add mmc_vddrange_to_ocrmask() helper function
This function sets the OCR mask bits according to provided voltage
ranges. Will be used by the mmc_spi OpenFirmware bindings.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-12-31 18:18:13 +01:00
Pierre Ossman 493890e75d mmc: increase SD write timeout for crappy cards
It seems that some cards are slightly out of spec and occasionally
will not be able to complete a write in the alloted 250 ms [1].
Incease the timeout slightly to allow even these cards to function
properly.

[1] http://lkml.org/lkml/2008/9/23/390

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-11-08 21:36:59 +01:00
Pierre Ossman a84756c573 mmc: properly iterate over sg list in debug check
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-08-01 19:03:37 +02:00
Pierre Ossman ad3868b2ec mmc,sdio: helper function for transfer padding
There are a lot of crappy controllers out there that cannot handle
all the request sizes that the MMC/SD/SDIO specifications require.
In case the card driver can pad the data to overcome the problems,
this commit adds a helper that calculates how much that padding
should be.

A corresponding helper is also added for SDIO, but it can also deal
with all the complexities of splitting up a large transfer efficiently.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-07-15 14:14:44 +02:00
Anton Vorontsov 28f52482b4 mmc: add support for card-detection polling
Some hosts (and boards that use mmc_spi) do not use interrupts on the CD
line, so they can't trigger mmc_detect_change. We want to poll the card
and see if there was a change. 1 second poll interval seems resonable.

This patch also implements .get_cd() host operation, that could be used
by the hosts that are able to report card-detect status without need to
talk MMC.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-07-15 14:14:41 +02:00
Adrian Bunk 98b843be56 mmc: proper prototypes for mmc_attach_*()
This patch adds proper prototypes for mmc_attach_*() in
drivers/mmc/core/core.h

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:32 +02:00
Adrian Bunk 261172fd1b mmc: make __mmc_release_bus() static
This patch makes the needlessly global __mmc_release_bus() static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-04-18 20:05:32 +02:00
Adrian Bunk 87ae9afdca cleanup asm/scatterlist.h includes
Not architecture specific code should not #include <asm/scatterlist.h>.

This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-11-02 08:47:06 +01:00
Pierre Ossman af8350c756 mmc: add led trigger
Add a led trigger for each host controller that indicates if there
is a request active on the controller.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-24 07:15:48 +02:00
David Brownell af51715079 MMC core learns about SPI
Teach the MMC/SD/SDIO core about using SPI mode.

 - Use mmc_host_is_spi() so enumeration works through SPI signaling
   and protocols, not just the native versions.

 - Provide the SPI response type flags with each request issued,
   including requests from the new lock/unlock code.

 - Understand that cmd->resp[0] and mmc_get_status() results for SPI
   return different values than for "native" MMC/SD protocol; this
   affects resetting, checking card lock status, and some others.

 - Understand that some commands act a bit differently ... notably:
     * OP_COND command doesn't return the OCR
     * APP_CMD status doesn't have an R1_APP_CMD analogue

Those changes required some new and updated primitives:

 - Provide utilities to access two SPI-only requests, and one
   request that wasn't previously needed:
     * mmc_spi_read_ocr() ... SPI only
     * mmc_spi_set_crc() ... SPI only (override by module parm)
     * mmc_send_cid() ... for use without broadcast mode

 - Updated internal routines:
     * Previous mmc_send_csd() modified into mmc_send_cxd_native();
       it uses native "R2" responses, which include 16 bytes of data.
     * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
       helper for command-and-data access
     * Bugfix to that mmc_send_cxd_data() code:  dma-to-stack is
       unsafe/nonportable, so kmalloc a bounce buffer instead.

 - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper

 - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
   those helper routines based on whether they're native or SPI

The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI:  MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:51:30 +02:00
Pierre Ossman f9996aee36 mmc: increase power up delay
Increase delay for power up in order to support some slower boards.

Also add some comments about why the delays are there.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:26:06 +02:00
Pierre Ossman d84075c8ae mmc: replace BUG_ON with WARN_ON
Replace all cases of BUG_ON with WARN_ON where there is a chance
(with varying degrees of slim) that the kernel can continue without
incidence.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:23:07 +02:00
Pierre Ossman e6f918bf39 mmc: fix sdio timeout calculation
SDIO doesn't have a CSD so it uses different timeout values than
SD memory.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:16:01 +02:00
Pierre Ossman ce252edd86 mmc: fix incorrect divisor in debug output
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 21:15:45 +02:00
Nicolas Pitre 2342f3323c sdio: allow for mmc_claim_host to be aborted
It is sometimes necessary to give up on trying to claim the host lock,
especially if that happens in a thread that has to be stopped.

While at it, fix the description for mmc_claim_host() which was wrong.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:55:13 +02:00
Nicolas Pitre 26074962e8 mmc: initialize mmc subsystem with subsys_initcall()
The problem is that the sdio_bus must be registered before any SDIO
drivers are registered against it otherwise the kernel sulks.  Because
the sdio_bus registration happens through module_init (equivalent to
device_initcall), then any SDIO
drivers linked before the SDIO core code in the kernel will be initialized
first.

Upcoming SDIO function drivers are likely to be located outside the
drivers/mmc directory as it is common practice to group drivers according
to their function rather than the bus they use.  SDIO drivers are therefore
likely to appear at random location in the kernel link.

To make sure the sdio_bus is always initialized before any SDIO drivers,
let's move the MMC init to the subsys_initcall level.

Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 20:45:39 +02:00
Pierre Ossman e29a7d73f4 mmc: basic SDIO device model
Add the sdio bus type and basic device handling.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 19:45:31 +02:00
Pierre Ossman 5c4e6f1301 mmc: detect SDIO cards
Really basic init sequence for SDIO cards.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 19:40:07 +02:00
Pierre Ossman b146d26a61 mmc: mmc_set_data_timeout() parameter write is redundant
The write parameter in mmc_set_data_timeout() is redundant as the
data structure contains information about the direction of the
transfer.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 09:15:00 +02:00
Pierre Ossman 17b0429dde mmc: remove custom error codes
Convert the MMC layer to use standard error codes and not its own,
incompatible values.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-09-23 08:46:48 +02:00
Adrian Bunk 393618510d drivers/mmc/core/: make 3 functions static
This patch makes the following needlessly global functions static:
- sd_ops.c: mmc_app_cmd()
- core.c: __mmc_release_bus()
- core.c: mmc_start_request()

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-07-26 02:05:57 +02:00
Pierre Ossman e4d2170874 mmc: proper debugging output in core
Make sure that the debugging output in the core is complete.
This should allow us to clean up all the extra debug output
that each and every other host driver seems to contain.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-07-26 02:05:30 +02:00
Pierre Ossman cf795bfb3a mmc: add a might_sleep() to mmc_claim_host()
In the normal case, the host lock can be claimed directly.
When it cannot, the caller will sleep. Make sure we don't
have any latent bugs by always calling might_sleep().

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-07-26 01:53:48 +02:00
Pierre Ossman 67a61c4847 mmc: update kerneldoc
Make sure the kerneldoc comments are up to date and relevant.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-07-26 01:53:39 +02:00
Pierre Ossman ffce2e7e70 mmc: move layer init and workqueue to core file
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-07-09 21:28:06 +02:00
Pierre Ossman b93931a61a mmc: refactor host class handling
Move basic host class device handling to its own file for clarity.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-07-09 21:28:01 +02:00
Pierre Ossman 4101c16a91 mmc: refactor bus operations
Move bus operations to its own file for the sake of clarity. Also
delegate sysfs attributes to bus handlers in preparation for other
more exotic types.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-07-09 21:27:56 +02:00
Andrew Morton 01f41ec7b3 mmc build fix
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-09 12:30:44 -07:00
Pierre Ossman 1efd48b3ae mmc: use lock instead of claim in debug check
As mmc_detect_change() can be called from irq context, using
claim (which can sleep) is inherently unsafe. Use the host
spinlock instead, which also is faster.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-05-08 22:42:57 +02:00
Pierre Ossman 6abaa0c9fe mmc: support unsafe resume of cards
Since many have the system root on MMC/SD we must allow some foot
shooting when it comes to resume.

We cannot detect if a card is removed and reinserted during suspend,
so the safe approach would be to assume it was, avoiding potential
filesystem corruption. This will of course not work if you cannot
release the card before suspend.

This commit adds a compile time option that makes the MMC layer
assume the card wasn't touched if it is redetected upon resume.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-05-01 16:00:02 +02:00
Pierre Ossman 7ea239d9e6 mmc: add bus handler
Delegate protocol handling to "bus handlers". This allows the core to
just handle the task of arbitrating the bus. Initialisation and
pampering of cards is now done by the different bus handlers.

This design also allows MMC and SD (and later SDIO) to be more cleanly
separated, allowing easier maintenance.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-05-01 13:41:06 +02:00
Pierre Ossman da7fbe58d2 mmc: Separate out protocol ops
Move protocol operations and definitions into their own files
in an effort to separate protocol handling and bus
arbitration more clearly.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-05-01 13:04:18 +02:00
Pierre Ossman aaac1b470b mmc: Move core functions to subdir
Create a "core" subdirectory to house the central bus handling
functions.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-05-01 13:04:18 +02:00