ARConnect/MCIP IPI sending has a retry-wait loop in case caller had
not seen a previous such interrupt. Turns out that it is not needed at
all. Linux cross core calling allows coalescing multiple IPIs to same
receiver - it is fine as long as there is one.
This logic is built into upper layer already, at a higher level of
abstraction. ipi_send_msg_one() sets the actual msg payload, but it only
calls MCIP IPI sending if msg holder was empty (using
atomic-set-new-and-get-old construct). Thus it is unlikely that the
retry-wait looping was ever getting exercised at all.
Cc: Chuck Jordan <cjordan@synopsys.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
There is no real ARC700 based SMP SoC so remove IPI definition.
EZChip's SMP ARC700 is going to use a different intc and IPI provider
anyways.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARConnect/MCIP Inter-Core-Interrupt module can't send interrupt to
local core. So use core intc capability to trigger software
interrupt to self, using an unsued IRQ #21.
This showed up as csd deadlock with LTP trace_sched on a dual core
system. This test acts as scheduler fuzzer, triggering all sorts of
schedulting activity. Trouble starts with IPI to self, which doesn't get
delivered (effectively lost due to H/w capability), but the msg intended
to be sent remain enqueued in per-cpu @ipi_data.
All subsequent IPIs to this core from other cores get elided due to the
IPI coalescing optimization in ipi_send_msg_one() where a pending msg
implies an IPI already sent and assumes other core is yet to ack it.
After the elided IPI, other core simply goes into csd_lock_wait()
but never comes out as this core never sees the interrupt.
Fixes STAR 9001008624
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org> [4.2]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
multipath is handling faults due to path failures. This leak does not
happen if blk-mq DM multipath is used. It only occurs if .request_fn DM
multipath is stacked ontop of blk-mq paths (e.g. scsi-mq devices).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWzL++AAoJEMUj8QotnQNa++YIAOHGHCMSODU37RVEeTgPXQMX
snT95xbUySmvW5s1uGBISD/kObiwqtr/aDcPqMP4G3piuaRVs07V8wqn2vWVOU9z
g3DEmPF7lsJYg5zisFqmQt1looISplxvXTUPA96vs6VHjUmn4uJKSCTEMtoXp4Xz
SbE0wZgM0p7IQY/dwRqVT7M0wMAoQRNGEz9+AyzvWCx47FFVTAO2RRG8af92Uikf
SpQSqvxxlK/eptexAgEspBcJ/o12vCQc99OFyYgf7td28o3DmBsPg2z+nwDmdIdP
NpvmlOE5dyYfS3ysKSdd2E3kNgyUNI0g9Y+gPtR1EvP87HJfESj4yNcznRFzTmk=
=4YyS
-----END PGP SIGNATURE-----
Merge tag 'dm-4.5-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix a 112 byte leak for each IO request that is requeued while DM
multipath is handling faults due to path failures.
This leak does not happen if blk-mq DM multipath is used. It only
occurs if .request_fn DM multipath is stacked ontop of blk-mq paths
(e.g. scsi-mq devices)"
* tag 'dm-4.5-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix dm_rq_target_io leak on faults with .request_fn DM w/ blk-mq paths
A recent bugfix changed pfn_t to always be 64-bit wide, but did not
change the code in pmem.c, which is now broken on 32-bit architectures
as reported by gcc:
In file included from ../drivers/nvdimm/pmem.c:28:0:
drivers/nvdimm/pmem.c: In function 'pmem_alloc':
include/linux/pfn_t.h:15:17: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
#define PFN_DEV (1ULL << (BITS_PER_LONG_LONG - 3))
This changes the intermediate pfn_flags in struct pmem_device to
be 64 bit wide as well, so they can store the flags correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: db78c22230 ("mm: fix pfn_t vs highmem")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
devm_memremap() returns an ERR_PTR() value in case of error.
However, it returns NULL when memremap() failed. This causes
the caller, such as the pmem driver, to proceed and oops later.
Change devm_memremap() to return ERR_PTR(-ENXIO) when memremap()
failed.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The original format of these commands from the "NVDIMM DSM Interface
Example" [1] are superseded by the ACPI 6.1 definition of the "NVDIMM Root
Device _DSMs" [2].
[1]: http://pmem.io/documents/NVDIMM_DSM_Interface_Example.pdf
[2]: http://www.uefi.org/sites/default/files/resources/ACPI_6_1.pdf
"9.20.7 NVDIMM Root Device _DSMs"
Changes include:
1/ New 'restart' fields in ars_status, unfortunately these are
implemented in the middle of the existing definition so this change
is not backwards compatible. The expectation is that shipping
platforms will only ever support the ACPI 6.1 definition.
2/ New status values for ars_start ('busy') and ars_status ('overflow').
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Linda Knippers <linda.knippers@hpe.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Stable bugfixes:
- Fix nfs_size_to_loff_t
- NFSv4: Fix a dentry leak on alias use
Other bugfixes:
- Don't schedule a layoutreturn if the layout segment can be freed immediately.
- Always set NFS_LAYOUT_RETURN_REQUESTED with lo->plh_return_iomode
- rpcrdma_bc_receive_call() should init rq_private_buf.len
- fix stateid handling for the NFS v4.2 operations
- pnfs/blocklayout: fix a memeory leak when using,vmalloc_to_page
- fix panic in gss_pipe_downcall() in fips mode
- Fix a race between layoutget and pnfs_destroy_layout
- Fix a race between layoutget and bulk recalls
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/WDS
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.5-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Stable bugfixes:
- Fix nfs_size_to_loff_t
- NFSv4: Fix a dentry leak on alias use
Other bugfixes:
- Don't schedule a layoutreturn if the layout segment can be freed
immediately.
- Always set NFS_LAYOUT_RETURN_REQUESTED with lo->plh_return_iomode
- rpcrdma_bc_receive_call() should init rq_private_buf.len
- fix stateid handling for the NFS v4.2 operations
- pnfs/blocklayout: fix a memeory leak when using,vmalloc_to_page
- fix panic in gss_pipe_downcall() in fips mode
- Fix a race between layoutget and pnfs_destroy_layout
- Fix a race between layoutget and bulk recalls"
* tag 'nfs-for-4.5-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.x/pnfs: Fix a race between layoutget and bulk recalls
NFSv4.x/pnfs: Fix a race between layoutget and pnfs_destroy_layout
auth_gss: fix panic in gss_pipe_downcall() in fips mode
pnfs/blocklayout: fix a memeory leak when using,vmalloc_to_page
nfs4: fix stateid handling for the NFS v4.2 operations
NFSv4: Fix a dentry leak on alias use
xprtrdma: rpcrdma_bc_receive_call() should init rq_private_buf.len
pNFS: Always set NFS_LAYOUT_RETURN_REQUESTED with lo->plh_return_iomode
pNFS: Fix pnfs_mark_matching_lsegs_return()
nfs: fix nfs_size_to_loff_t
In commit 11f1a4b975 ("x86: reorganize SMAP handling in user space
accesses") I changed how the stac/clac instructions were generated
around the user space accesses, which then made it possible to do
batched accesses efficiently for user string copies etc.
However, in doing so, I completely spaced out, and didn't even think
about the 32-bit case. And nobody really even seemed to notice, because
SMAP doesn't even exist until modern Skylake processors, and you'd have
to be crazy to run 32-bit kernels on a modern CPU.
Which brings us to Andy Lutomirski.
He actually tested the 32-bit kernel on new hardware, and noticed that
it doesn't work. My bad. The trivial fix is to add the required
uaccess begin/end markers around the raw accesses in <asm/uaccess_32.h>.
I feel a bit bad about this patch, just because that header file really
should be cleaned up to avoid all the duplicated code in it, and this
commit just expands on the problem. But this just fixes the bug without
any bigger cleanup surgery.
Reported-and-tested-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No users, nuke them.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-kfv2wo8xann8t97wdalttcx7@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It is the only user of this function, just use the strlen() to skip
the prefix.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-blao710l5cd5hmwrhy51ftgq@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When we allocate bitmaps in vgic_vcpu_init_maps, we divide the number of
bits we need by 8 to figure out how many bytes to allocate. However,
bitmap elements are always accessed as unsigned longs, and if we didn't
happen to allocate a size such that size % sizeof(unsigned long) == 0,
bitmap accesses may go past the end of the allocation.
When using KASAN (which does byte-granular access checks), this results
in a continuous stream of BUGs whenever these bitmaps are accessed:
=============================================================================
BUG kmalloc-128 (Tainted: G B ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in vgic_init.part.25+0x55c/0x990 age=7493 cpu=3 pid=1730
INFO: Slab 0xffffffbde6d5da40 objects=16 used=15 fp=0xffffffc935769700 flags=0x4000000000000080
INFO: Object 0xffffffc935769500 @offset=1280 fp=0x (null)
Bytes b4 ffffffc9357694f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffffffc935769500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffffffc935769510: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffffffc935769520: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffffffc935769530: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffffffc935769540: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffffffc935769550: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffffffc935769560: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Object ffffffc935769570: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Padding ffffffc9357695b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Padding ffffffc9357695c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Padding ffffffc9357695d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Padding ffffffc9357695e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
Padding ffffffc9357695f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
CPU: 3 PID: 1740 Comm: kvm-vcpu-0 Tainted: G B 4.4.0+ #17
Hardware name: ARM Juno development board (r1) (DT)
Call trace:
[<ffffffc00008e770>] dump_backtrace+0x0/0x280
[<ffffffc00008ea04>] show_stack+0x14/0x20
[<ffffffc000726360>] dump_stack+0x100/0x188
[<ffffffc00030d324>] print_trailer+0xfc/0x168
[<ffffffc000312294>] object_err+0x3c/0x50
[<ffffffc0003140fc>] kasan_report_error+0x244/0x558
[<ffffffc000314548>] __asan_report_load8_noabort+0x48/0x50
[<ffffffc000745688>] __bitmap_or+0xc0/0xc8
[<ffffffc0000d9e44>] kvm_vgic_flush_hwstate+0x1bc/0x650
[<ffffffc0000c514c>] kvm_arch_vcpu_ioctl_run+0x2ec/0xa60
[<ffffffc0000b9a6c>] kvm_vcpu_ioctl+0x474/0xa68
[<ffffffc00036b7b0>] do_vfs_ioctl+0x5b8/0xcb0
[<ffffffc00036bf34>] SyS_ioctl+0x8c/0xa0
[<ffffffc000086cb0>] el0_svc_naked+0x24/0x28
Memory state around the buggy address:
ffffffc935769400: 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffffffc935769480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffffffc935769500: 04 fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffffffc935769580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffffffc935769600: 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Fix the issue by always allocating a multiple of sizeof(unsigned long),
as we do elsewhere in the vgic code.
Fixes: c1bfb577a ("arm/arm64: KVM: vgic: switch to dynamic allocation")
Cc: stable@vger.kernel.org
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The qword_get() function NUL-terminates its output buffer. If the input
string is in hex format \xXXXX... and the same length as the output
buffer, there is an off-by-one:
int qword_get(char **bpp, char *dest, int bufsize)
{
...
while (len < bufsize) {
...
*dest++ = (h << 4) | l;
len++;
}
...
*dest = '\0';
return len;
}
This patch ensures the NUL terminator doesn't fall outside the output
buffer.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
When an error happens during alias parsing currently the complete
parsing of all attributes of the PMU is stopped. This is breaks old perf
on a newer kernel that may have not-yet-know alias attributes (such as
.scale or .per-pkg).
Continue when some attribute is unparseable.
This is IMHO a stable candidate and should be backported to older
versions to avoid problems with newer kernels.
v2: Print warnings when something goes wrong.
v3: Change warning to debug output
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: stable@vger.kernel.org # v3.6+
Link: http://lkml.kernel.org/r/1455749095-18358-1-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding data_src and weight column definitions, so it's displayed for
related sample types.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1455525293-8671-22-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
There's no need to define extra macros for that.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1455525293-8671-13-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adding -e option for perf mem record command, to be able to specify
memory event directly.
Get list of available events:
$ perf mem record -e list
ldlat-loads
ldlat-stores
Monitor ldlat-loads:
$ perf mem record -e ldlat-loads true
Committer notes:
Further testing:
# perf mem record -e ldlat-loads true
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.020 MB perf.data (10 samples) ]
# perf evlist
cpu/mem-loads,ldlat=30/P
#
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1455525293-8671-6-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It will ease up configuration of memory events and addition of other
memory events in following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1455525293-8671-5-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It'll be used in following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1455525293-8671-4-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It'll be used in following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1455525293-8671-3-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The operation '%' is not implemented on event-parse.c, causing an error
when parsing events with '%' the operation in its printk format. For
example,
# perf record -e sched:sched_deadline_yield ~/yield-test
Warning: [sched:sched_deadline_yield] unknown op '%'
....
# perf script
Warning: [sched:sched_deadline_yield] unknown op '%'
test 1641 [006] 3364.109319: sched:sched_deadline_yield: \
[FAILED TO PARSE] now=3364109314595 \
deadline=3364139295135 runtime=19975597
This patch implements the '%' operation. With this patch, we see the
correct output:
# perf record -e sched:sched_deadline_yield ~/yield-test
No Warning
# perf script
yield-test 4005 [001] 4623.650978: sched:sched_deadline_yield: \
now=4623.650974050 \
deadline=4623.680957364 remaining_runtime=19979611
Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Juri Lelli <juri.lelli@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-rt-users <linux-rt-users@vger.kernel.org>
Link: http://lkml.kernel.org/r/5c96a395c56cea6d3d13d949051bdece86cc26e0.1456157869.git.bristot@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Even though DEVTMPFS is required when our pre-built initramfs
is used it is not the case in general. It is perfectly possible
to use initramfs with device nodes already populated or there
could be other usages, see discussion below for more detials:
http://thread.gmane.org/gmane.comp.embedded.openwrt.devel/37819/focus=37821
This change removes mentioned dependency from arch/arc/Kconfig
updating instead those defconfigs that are usually used with this
kind of pre-build initramfs.
And while at it all touched defconfigs were regenerated via
savedefconfig and some options were removed:
* USB is selected by other options implicitly
* VGA_CONSOLE is disableb for ARC since
031e29b587
* EXT3_FS automatically selects EXT4_FS
* MTDxxx and JFFS2_FS make no sense for AXS because
AXS NAND controller is not upstreamed
* NET_OSCI_LAN is not in upstream as well
* ARCPGU_xxx options make no sense because ARC PGU is not yet
in upstream and when it gets there all config options would
be taken from devicetree
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Now that I have switched to another company, I won't
be able to help by maintaining OMAP USB Support and/or
the MUSB driver.
OMAP USB Support is left Orphaned. MUSB's new
maintainer will be Bin Liu from Texas Instruments
who has accepted to take over starting with v4.6.
Cc: Bin Liu <b-liu@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Commit ac33cdb166 ("usb: musb: Remove ifdefs for musb_host_rx in
musb_host.c part5") introduces a problem setting DMA host mode.
The musb_advance_schedule() is called immediately after receiving an
endpoint RX interrupt without waiting for the DMA transfer to complete.
As a consequence when the dma complete interrupt arrives the in_qh
member of hw_ep is already null an the musb_host_rx() exits on !urb
error case. Fix the done condition that advances the musb schedule.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When working in Dual Role Device mode, USB state machine is not kicked,
when host or gadget drivers are loaded. Fix this be explicitly triggering
state detection on client driver load.
Issue is that if the board is booted without micro usb cable and usb
device attached, kernel fails to populate the usb host and device.
The reason for this is that the state machine worker logic only checks
for USB_DR_MODE_PERIPHERAL and USB_DR_MODE_HOST modes to run worker
thread. However if the phy is configured in OTG mode it would fail
to run the state machine, resulting in failure to detect for very
first time.
This patch fixes the issue by removing the explicit checks.
Issue is noticed on Qualcomm Dragon board DB410C.
[srinivas.kandagatla@linaro.org: Added more details to log]
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch fixes the register offset used for super-speed connection's
max packet size. Without it using the 338x series of devices in enhanced
mode will only allow full or high speed operation to function correctly.
Signed-off-by: Simon Appleby <simon.appleby@pickeringtest.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Gadgetfs driver called usb_gadget_unregister_driver unconditionally, even
if it didn't register it earlier due to other failures. This patch fixes
this.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Retry gadget probe only if the probe result is -EPROBE_DEFER, not on
every probe error.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently when setting up an IMR around the kernel's .text section we lock
that IMR, preventing further modification. While superficially this appears
to be the right thing to do, in fact this doesn't account for a legitimate
change in the memory map such as when executing a new kernel via kexec.
In such a scenario a second kernel can have a different size and location
to it's predecessor and can view some of the memory occupied by it's
predecessor as legitimately usable DMA RAM. If this RAM were then
subsequently allocated to DMA agents within the system it could conceivably
trigger an IMR violation.
This patch fixes the this potential situation by keeping the kernel's .text
section IMR lock bit false by default.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: boon.leong.ong@intel.com
Cc: paul.gortmaker@windriver.com
Link: http://lkml.kernel.org/r/1456190999-12685-2-git-send-email-pure.logic@nexus-software.ie
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As per the documentation of the devfreq_dev_profile.target callback, set
the freq argument to the new frequency before returning.
This caused endless messages like this after recent changes in the core:
devfreq 6000c800.actmon: Couldn't update frequency transition information.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reported-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Replace another case where the layout 'plh_block_lgets' can trigger
infinite loops in send_layoutget().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If the server reboots while there is a layoutget outstanding, then
the call to pnfs_choose_layoutget_stateid() will fail with an EAGAIN
error, which causes an infinite loop in send_layoutget(). The reason
why we never break out of the loop is that the layout 'plh_block_lgets'
field is never cleared.
Fix is to replace plh_block_lgets with NFS_LAYOUT_INVALID_STID, which
can be reset after a new layoutget.
Fixes: ab7d763e47 ("pNFS: Ensure nfs4_layoutget_prepare returns...")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
One is by Yang Shi who added a READ_ONCE_NOCHECK() to the scan of the
stack made by the stack tracer. As the stack tracer scans the entire
kernel stack, KASAN triggers seeing it as a "stack out of bounds" error.
As the scan is looking at the contents of the stack from parent functions.
The NOCHECK() tells KASAN that this is done on purpose, and is not some
kind of stack overflow.
The second fix is to the ftrace selftests, to retrieve the PID of executed
commands from the shell with "$!" and not by parsing "jobs".
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWyycyAAoJEKKk/i67LK/8ALoH/RkMZ7Cih7vXb30wB13xSNrB
6o4ApuC4YOS9Un/4ruCXb+cGbW2LJLHkEU2ageoHLOZMvwuAM7iQ6fTUW1KxCRP2
ECvqyqi0ZRyoi/CibxVVH9hHEAJzUTwok67nkLeZBqIN9Fglcfd7toAwgcrH3y59
Pybyv5CV2eaff5IKoLXKZJNRLdrVLeM7v4BvdI0dxEikhWZ0XsA0RoIaNfTPqyQJ
F6sJ/njdoMMJK4N8CCPxlvnvEOzn0DnJnfUNUQEj5J3YU9DbAHAACaBSg5oSh9oK
BcFYKV2GIzPku1cafutRRlErcGyB2yqv7bB8Eo86zXRHbeonaj4XGJmH276ldVg=
=srlj
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Two more small fixes.
One is by Yang Shi who added a READ_ONCE_NOCHECK() to the scan of the
stack made by the stack tracer. As the stack tracer scans the entire
kernel stack, KASAN triggers seeing it as a "stack out of bounds"
error. As the scan is looking at the contents of the stack from
parent functions. The NOCHECK() tells KASAN that this is done on
purpose, and is not some kind of stack overflow.
The second fix is to the ftrace selftests, to retrieve the PID of
executed commands from the shell with '$!' and not by parsing 'jobs'"
* tag 'trace-fixes-v4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing, kasan: Silence Kasan warning in check_stack of stack_tracer
ftracetest: Fix instance test to use proper shell command for pids
As the code in this file is being executed within irq context in some
cases, we must avoid the clk_get_rate which uses mutex internally.
Switch the code to use clk_hw_get_rate instead which is non-locking.
This fixes an issue where PM runtime will hang the system if enabled
with a serial console before a suspend-resume cycle.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Fixes: a53ad8ef3d ("clk: ti: Convert to clk_hw based provider APIs")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- Two scsiback fixes (resource leak and spurious warning).
- Fix DMA mapping of compound pages on arm/arm64.
- Fix some pciback regressions in MSI-X handling.
- Fix a pcifront crash due to some uninitialize state.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWyvatAAoJEFxbo/MsZsTRBFcH+wWnv0/N+gKib3cKCI4lwmTg
n8iVgf8dNWwD36M2s/OlzCAglAIt8Xr6ySNvPqTerpm7lT9yXlIVQxGXTbIGuTAA
h8Kt8WiC0BNLHHlLxBuCz62KR47DvMhsr84lFURE8FmpUiulFjXmRcbrZkHIMYRS
l/X+xJWO1vxwrSYho0P9n3ksTWHm488DTPvZz3ICNI2G2sndDfbT3gv3tMDaQhcX
ZaQR93vtIoldqk29Ga59vaVtksbgxHZIbasY9PQ8rqOxHJpDQbPzpjocoLxAzf50
cioQVyKQ7i9vUvZ+B3TTAOhxisA2hDwNhLGQzmjgxe2TXeKdo3yjYwO6m1dDBzY=
=VY/S
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.5-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Two scsiback fixes (resource leak and spurious warning).
- Fix DMA mapping of compound pages on arm/arm64.
- Fix some pciback regressions in MSI-X handling.
- Fix a pcifront crash due to some uninitialize state.
* tag 'for-linus-4.5-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pcifront: Fix mysterious crashes when NUMA locality information was extracted.
xen/pcifront: Report the errors better.
xen/pciback: Save the number of MSI-X entries to be copied later.
xen/pciback: Check PF instead of VF for PCI_COMMAND_MEMORY
xen: fix potential integer overflow in queue_reply
xen/arm: correctly handle DMA mapping of compound pages
xen/scsiback: avoid warnings when adding multiple LUNs to a domain
xen/scsiback: correct frontend counting
Pull networking fixes from David Miller:
"Looks like a lot, but mostly driver fixes scattered all over as usual.
Of note:
1) Add conditional sched in nf conntrack in cleanup to avoid NMI
watchdogs. From Florian Westphal.
2) Fix deadlock in nfnetlink cttimeout, also from Floarian.
3) Fix handling of slaves in bonding ARP monitor validation, from Jay
Vosburgh.
4) Callers of ip_cmsg_send() are responsible for freeing IP options,
some were not doing so. Fix from Eric Dumazet.
5) Fix per-cpu bugs in mvneta driver, from Gregory CLEMENT.
6) Fix vlan handling in mv88e6xxx DSA driver, from Vivien Didelot.
7) bcm7xxx PHY driver bug fixes from Florian Fainelli.
8) Avoid unaligned accesses to protocol headers wrt. GRE, from
Alexander Duyck.
9) SKB leaks and other problems in arc_emac driver, from Alexander
Kochetkov.
10) tcp_v4_inbound_md5_hash() releases listener socket instead of
request socket on error path, oops. Fix from Eric Dumazet.
11) Missing socket release in pppoe_rcv_core() that seems to have
existed basically forever. From Guillaume Nault.
12) Missing slave_dev unregister in dsa_slave_create() error path,
from Florian Fainelli.
13) crypto_alloc_hash() never returns NULL, fix return value check in
__tcp_alloc_md5sig_pool. From Insu Yun.
14) Properly expire exception route entries in ipv4, from Xin Long.
15) Fix races in tcp/dccp listener socket dismantle, from Eric
Dumazet.
16) Don't set IFF_TX_SKB_SHARING in vxlan, geneve, or GRE, it's not
legal. These drivers modify the SKB on transmit. From Jiri Benc.
17) Fix regression in the initialziation of netdev->tx_queue_len.
From Phil Sutter.
18) Missing unlock in tipc_nl_add_bc_link() error path, from Insu Yun.
19) SCTP port hash sizing does not properly ensure that table is a
power of two in size. From Neil Horman.
20) Fix initializing of software copy of MAC address in fmvj18x_cs
driver, from Ken Kawasaki"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (129 commits)
bnx2x: Fix 84833 phy command handler
bnx2x: Fix led setting for 84858 phy.
bnx2x: Correct 84858 PHY fw version
bnx2x: Fix 84833 RX CRC
bnx2x: Fix link-forcing for KR2
net: ethernet: davicom: fix devicetree irq resource
fmvj18x_cs: fix incorrect indexing of dev->dev_addr[] when copying the MAC address
Driver: Vmxnet3: Update Rx ring 2 max size
net: netcp: rework the code for get/set sw_data in dma desc
soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data
net: ti: netcp: restore get/set_pad_info() functionality
MAINTAINERS: Drop myself as xen netback maintainer
sctp: Fix port hash table size computation
can: ems_usb: Fix possible tx overflow
Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb
net: bcmgenet: Fix internal PHY link state
af_unix: Don't use continue to re-execute unix_stream_read_generic loop
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
bnxt_en: Failure to update PHY is not fatal condition.
bnxt_en: Remove unnecessary call to update PHY settings.
...
Remove an un-necessary speed_index lookup for thermal hook in the gpio-fan
driver. The unnecessary speed lookup can hog the system.
Handle negative conversion values correctly in the ads1015 driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=luAI
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Two fixes headed for stable:
- Remove an unnecessary speed_index lookup for thermal hook in the
gpio-fan driver. The unnecessary speed lookup can hog the system.
- Handle negative conversion values correctly in the ads1015 driver"
* tag 'hwmon-for-linus-v4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (gpio-fan) Remove un-necessary speed_index lookup for thermal hook
hwmon: (ads1015) Handle negative conversion values correctly
- One fix ocrdma - The new CQ API support was added to ocrdma, but they
got the arming logic wrong, so without this, transfers eventually fail
when they fail to arm the interrupt properly under load
- Two related fixes for mlx4 - When we added the 64bit extended counters
support to the core IB code, they forgot to update the RoCE side of the
mlx4 driver (the IB side they properly updated). I debated whether or
not to include these patches as they could be considered feature
enablement patches, but the existing code will blindy copy the 32bit
counters, whether any counters were requested at all (a bug). These
two patches make it A) check to see that counters were requested and
B) copy the right counters (the 64bit support is new, the 32bit is
not). For that reason I went ahead and took them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QD36
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"One ocrdma fix:
- The new CQ API support was added to ocrdma, but they got the arming
logic wrong, so without this, transfers eventually fail when they
fail to arm the interrupt properly under load
Two related fixes for mlx4:
- When we added the 64bit extended counters support to the core IB
code, they forgot to update the RoCE side of the mlx4 driver (the
IB side they properly updated).
I debated whether or not to include these patches as they could be
considered feature enablement patches, but the existing code will
blindy copy the 32bit counters, whether any counters were requested
at all (a bug).
These two patches make it (a) check to see that counters were
requested and (b) copy the right counters (the 64bit support is
new, the 32bit is not). For that reason I went ahead and took
them"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/mlx4: Add support for the port info class for RoCE ports
IB/mlx4: Add support for extended counters over RoCE ports
RDMA/ocrdma: Fix arm logic to align with new cq API
Pull i2c fixes from Wolfram Sang:
"Some bugfixes from I2C for you:
A fix for a RuntimePM regression with OMAP, a fix to enable TCO for
Lewisburg platforms, and a typo fix while we are here"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Adding Intel Lewisburg support for iTCO
i2c: uniphier: fix typos in error messages
i2c: omap: Fix PM regression with deferred probe for pm_runtime_reinit
- EOI handling for LPIs when GICv3 is in EOImode==1
- Another fallout from changing page size while allocating ITS tables
- Missing memory barrier in the 32bit GICv3 code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZtCQ
-----END PGP SIGNATURE-----
Merge tag 'gic-fixes-4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull GIC fixes for 4.5-rc5 from Marc Zyngier:
- EOI handling for LPIs when GICv3 is in EOImode==1
- Another fallout from changing page size while allocating ITS tables
- Missing memory barrier in the 32bit GICv3 code
It has been observed that sometimes disabling the dc6 fails
and dc6 state pops back up, brief moment after disabling. This
has to be dmc save/restore timing issue or other bug in the
way dc states are handled.
Try to work around this issue as we don't have firmware fix
yet available. Verify that the value we wrote for the dmc sticks,
and also enforce it by rewriting it, if it didn't.
v2: Zero rereads on rewrite for extra paranoia (Imre)
Testcase: kms_flip/basic-flip-vs-dpms
References: https://bugs.freedesktop.org/show_bug.cgi?id=93768
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455811089-27884-1-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 779cb5d3dd)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The DMC can incorrectly run off and allow DC states on it's own. We
don't know the root-cause for this yet but this patch makes it more
visible.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455808874-22089-2-git-send-email-mika.kuoppala@intel.com
(cherry picked from commit 832dba889e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
set_power_state defaults to no displays, so we need to update
the display configuration after setting up the powerstate on the
first call. In most cases this is not an issue since ends up
getting called multiple times at any given modeset and the proper
order is achieved in the display changed handling at the top of
the function.
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Jordan Lazare <Jordan.Lazare@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
set_power_state defaults to no displays, so we need to update
the display configuration after setting up the powerstate on the
first call. In most cases this is not an issue since ends up
getting called multiple times at any given modeset and the proper
order is achieved in the display changed handling at the top of
the function.
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Jordan Lazare <Jordan.Lazare@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Vineet Gupta