The cksm function in system.h is duplicate to csum_partial in checksum.h.
Remove cksm and use csum_partial instead.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is a cleanup of all the messages this driver prints. It uses the
dev_message macros now.
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide new shutdown action "dump_reipl" for automatic ipl after dump.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Standby memory detected with the sclp interface gets always registered
with add_memory calls without considering the limitationt that the
"mem=" kernel paramater implies.
So fix this and only register standby memory that is below the specified
limit.
This fixes zfcpdump since it uses "mem=32M". In case there is appr.
2GB standby memory present all of usable memory would be used for the
struct pages needed for standby memory.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Handle a malformed hardware response which some versions of the
Support Element (SE) may present during SE restart and which otherwise
would result in an endless loop in function sclp_dispatch_evbufs.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC drivers/s390/char/tape_block.o
In file included from drivers/s390/char/tape_block.c:24:
drivers/s390/char/tape.h:159: warning: 'struct request' declared inside
parameter list
Adding the dependency of CONFIG_BLOCK to CONFIG_S390_TAPE_BLOCK.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get rid of this one:
CC drivers/s390/char/sclp_vt220.o
drivers/s390/char/sclp_vt220.c:588: warning: '__sclp_vt220_flush_buffer' defined but not used
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The vmcp driver uses the session->mutex for concurrent access of the data
structures. Therefore, the BKL in vmcp_open does not protect against any
other function in the driver.
The BLK in vmcp_open would protect concurrent access to the module init
but all necessary steps ave finished before misc_register is called.
We can safely remove the lock_kernel from vcmp.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
__blk_end_request must be called with request queue lock held. We need to use
blk_end_request rather than __blk_end_request.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that device_create() has been audited, rename things back to the
original call to be sane.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop the kernel lock further and also correct cases where we set rc to an
error code, and then return 0
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_current_tty now does internal locking and returns a referenced object,
thus our use of tty_mutex here can go away.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently it is sometimes locked by the tty mutex and sometimes by the
sighand lock. The latter is in fact correct and now we can hand back referenced
objects we can fix this up without problems around sleeping functions.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We now return a kref covered tty reference. That ensures the tty structure
doesn't go away when you have a return from get_current_tty. This is not
enough to protect you from most of the resources being freed behind your
back - yet.
[Updated to include fixes for SELinux problems found by Andrew Morton and
an s390 leak found while debugging the former]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 3215 console irq handler used to schedule a tasklet. However the
console irq handler also gets called from the infamous cio_tpi()
function. Which in turn does something like
local_bh_disable()
[call console irq handler]
_local_bh_enable()
_local_bh_enable() prevents execution of softirqs, which is intended
within cio_tpi(). However there might be a new softirq pending because
irq handler scheduled a tasklet.
In order to prevent this behaviour we just get rid of the tasklet.
It's not doing much anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 console drivers use the unblank callback of the console
structure to flush the console buffer. In case of a panic or a
reboot the CPU doing the callback can block on the console i/o.
The other CPUs in the system continue to work. For panic this is
not a good idea.
Replace the unblank callback with proper panic/reboot notifier.
These get called after all but one CPU have been stopped.
Signed-off-by: Holger Smolinski <Holger.Smolinski@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some further bus_id -> dev_name() conversions in s390 code.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Convert most s390 users setting bus_id to dev_set_name().
css and ccw busses are deferred since they need some special
treatment.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case of error, functions dasd_kmalloc_request and idal_buffer_alloc
return an ERR pointer, but never return the NULL pointer. So after a
call to one of these functions, a NULL test should be replaced by an
IS_ERR test.
A simplified version of the semantic patch that makes this change is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@correct_null_test@
expression x,E;
statement S1, S2;
@@
x =
(
dasd_kmalloc_request(...)
|
idal_buffer_alloc(...)
)
<... when != x = E
if (
(
- x@p2 != NULL
+ ! IS_ERR ( x )
|
- x@p2 == NULL
+ IS_ERR( x )
)
)
S1
else S2
...>
? x = E;
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since git commit 3da1c84c00
"workqueues: make get_online_cpus() useable for work->func()"
it is safe to call get_online_cpus() from workqueue context.
So remove the kthread workaround again.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sclp_sync_wait wait synchronously for an sclp interrupt and disables
timer interrupts. However on the irq enter paths there is an extra
check if a timer interrupt would be due and calls the timer callback.
This would schedule softirqs in the wrong context.
So introduce local_tick_enable/disable which prevents this.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use -EOPNOTSUPP instead of -ENOTSUPP.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
The kernel part of zfcpdump establishes a new debugfs file zcore/memmap
which exports information on memory layout (start address and length of each
memory chunk) to its userspace counterpart.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Finally fixes a possible scheduling while in atomic context bug. The driver
used to wait on a waitqueue if no empty buffer was available. This could
lead to a deadlock if the driver was called from non-schedulable context.
So fix this. The write operation may fail now. It returns the number of
characters accepted. put_char will never fail, since it writes characters
to an intermediate buffer which gets flushed as soon as it is full.
That means the driver now can busy wait if something is in the intermediate
buffer and a write_string operation follows. Seems to be an acceptable
compromise, since that shouldn't happen too often.
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
After all we came to the conclusion that this interface doesn't make any
sense. Besides that the ioctl number used was never registered, the header
file isn't exported, and we doubt there is even a single user.
So remove this interface, since it eases maintenance.
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Most likely it is broken anyway because of the changes in memory
detection. Since we can't test it and there are probably better ways
that using a P390 card, remove support for it.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The message descriptions are still missing though ..
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Move memory detection code to own file and also simplify it.
Also add an interface which can be called at any time to get the
current memory layout. This interface is needed by our kernel
internal system dumper.
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Cc: Michael Holzheu <holzheu@de.ibm.com>
Cc: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
As noted by Akinobu Mita in patch b1fceac2b9,
alloc_bootmem and related functions never return NULL and always return a
zeroed region of memory. Thus a NULL test or memset after calls to these
functions is unnecessary.
drivers/s390/char/raw3270.c | 11 +----------
drivers/s390/char/sclp_con.c | 2 --
2 files changed, 1 insertion(+), 12 deletions(-)
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
statement S;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
(
- BUG_ON (E == NULL);
|
- if (E == NULL) S
)
@@
expression E,E1;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
- memset(E,0,E1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix a number of sclp_vt220 cleanup problems:
* fix list_empty check after list_del()
* mark init-only flag as __initdata
* remove implicit dependency between slab_available() and num_pages
* straighten multiple init handling (use init count)
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Extend the scsw data structure to the format required by fcx. Also
provide helper functions for easier access to fields which are present
in both the traditional as well as the modified format.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
smp_rescan_cpus() calls get_online_cpus() from a multithreaded
workqueue context. This may deadlock. This is the same bug as in
arch/s390/kernel/topology.c. This patch can be reverted as soon as
Oleg's patch gets merged.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In case the supported sclp facilities change
the new mask should be saved.
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Mutex locks are used to avoid problems when /sys/firmware/cpi data
are accessed to in parallel.
Signed-off-by: Michael Ernst <mernst@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
@r exists@
expression E,E1;
statement S;
position p1,p2,p3;
@@
E =@p1 \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != E = E1
if (E == NULL || ...) S
... when != E = E1
if@p2 (...) {
... when != kfree(E)
}
... when != E = E1
kfree@p3(E);
@forall@
position r.p2;
expression r.E;
int E1 != 0;
@@
* if@p2 (...) {
... when != kfree(E)
when strict
return E1; }
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A wait_event call with a stack local wait_queue_head_t structure that is
used to do the wake up for the wait_event is inherently racy. After the
wait_event finished the wake_up call might not have completed yet.
Replace the stack local wait_queue_head_t in tape_do_io and
tape_do_io_interruptible with a per device wait queue.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A wait_event call with a stack local wait_queue_head_t structure that is
used to do the wake up for the wait_event is inherently racy. After the
wait_event finished the wake_up call might not have completed yet.
Remove the stack local wait_queue_head_t from raw3270_start_init and
use the global raw3270_wait_queue instead.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The driver incorrectly assumed that putchar will only be called from
schedulable process context and therefore blocked and waited if no
free output buffers where available.
Since putchar may also be called from BH context this may lead to
deadlocks.
To fix this just return the number of characters accepted and let the
upper layer handle the rest.
The console write function will busy wait (sclp_sync_wait) until a
buffer is available again.
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This fixes the last remaining section mismatch warnings in s390
architecture code. It reveals also a real bug introduced by... me
with git commit 2069e978d5
("[S390] sparsemem vmemmap: initialize memmap.")
Calling the generic vmemmap_alloc_block() function to get initialized
memory is a nice idea, however that function is __meminit annotated
and therefore the function might be gone if we try to call it later.
This can happen if a DCSS segment gets added.
So basically revert the patch and clear the memmap explicitly to fix
the original bug.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Due to incorrect function call sequence it can happen that a tape block
request is finished before the request is taken from the block request queue.
The following sequence leads to that condition:
* tapeblock_start_request() -> start CCW program
* Request finishes -> IO interrupt
* tapeblock_end_request()
* end_that_request_last()
If blkdev_dequeue_request() has not been called before end_that_request_last(),
a kernel bug is triggered in end_that_request_last() because the request is
still queued. To solve that problem blkdev_dequeue_request() has to be called
before starting the CCW program.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is a race from when a device is created with device_create() and
then the drvdata is set with a call to dev_set_drvdata() in which a
sysfs file could be open, yet the drvdata will be NULL, causing all
sorts of bad things to happen.
This patch fixes the problem by using the new function,
device_create_drvdata().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To construct the integer containing the information from the bus_id,
it is easier to use the data from ccw_dev_id than to parse the bus_id.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The wrong function got coverted ;)
CC drivers/s390/char/tty3270.o
drivers/s390/char/tty3270.c:1747:
warning: initialization from incompatible pointer type
Acked-by: Alan Cox <alan@redhat.com>
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Put the changes into the drivers first. This will still compile/work but
produce a warning if bisected so can still be debugged
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create() to make sure that ->proc_fops be setup before gluing PDE to
main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove proc_root export. Creation and removal works well if parent PDE is
supplied as NULL -- it worked always that way.
So, one useless export removed and consistency added, some drivers created
PDEs with &proc_root as parent but removed them as NULL and so on.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the function that prints the segment warning messages found in the
monreader driver and the dcssblk driver to the extmem base code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
If user space opens a unit record device node then vmur is leaving the kernel
with lock open_mutex still held to prevent other processes from opening the
device simultaneously. This causes lockdep to complain about a lock held when
returning to user space.
Now the mutex is replaced by a wait queue to serialize device open.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
When a tape device is set online, offline and online again, the following
error message is printed on the console: "sysfs: duplicate filename
'non-rewinding' can not be created". The reason is that when setting a
device online, the tape driver creates a sysfs symlink from the tape device
to the tape class device. Unfortunately the symlink is not removed
correctly, when the device is set offline. Instead of passing the
tape device object to sysfs_remove_link, the class device object is used.
This patch fixes this problem and uses the correct tape device object now.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reintroduces in_interrupt() check in sclp_tty code. Add may_schedule
parameter to vt220 write function, so we can let the write function
know if it may schedule or not. So we disallow scheduling for all
console calls and may allow them for tty calls.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Currently an output buffer can wait up to HZ/2 until the buffer is
flushed. The wait time is noticeable in interactive tools like mc.
Change the value to HZ/20, which seems enough for interactive work.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Oddly enough, unsigned int c = '\300'; puts a "negative" value in c, not
0300... This fixes the default unicode compose table by using integers
instead of character constants.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make state change events adjust the correct mask by cleaning up
naming inconsistencies. Also remove chance for lockup by removing
unnecessary mask related check before reading events.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There are two problems in the vt220 intialization:
o Currently the vt220 console looses early printk events until the
the vt220 tty is registered.
o console should work if tty_register fails
sclp_vt220_con_init calls __sclp_vt220_init and register_console.
It does not register the driver with the sclp core code via
sclp_register. That results in an sclp_send_mask=0. Therefore,
__sclp_vt220_emit will reject buffers with EIO. Unfortunately
register_console will cause the printk buffer to be sent to the
console and, therefore, every early message gets dropped. The
sclp_send_mask is set later during boot, when sclp_vt220_tty_init
calls sclp_register.
The solution is to move the sclp_register call from sclp_vt220_tty_init
to __sclp_vt220_init. This makes sure that the console is properly
registered with the sclp subsystem before the first log buffer messages
are passed to the vt220 console.
We also adopt the cleanup on error to keep the console alive if
tty_register fails.
Thanks to Peter Oberparleiter and Heiko Carstens for review and ideas
for improvement.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Under load the following bug message appeared while using sysrq-t:
BUG: scheduling while atomic: bash/3662/0x00000004
0000000000105b74 000000003ba17740 0000000000000002 0000000000000000
000000003ba177e0 000000003ba17758 000000003ba17758 0000000000105bfe
0000000000817ba8 000000003f2a5350 0000000000000000 0000000000000000
000000003ba17740 000000000000000c 000000003ba17740 000000003ba177b0
0000000000568630 0000000000105bfe 000000003ba17740 000000003ba17790
Call Trace:
([<0000000000105b74>] show_trace+0x13c/0x158)
[<0000000000105c58>] show_stack+0xc8/0xfc
[<0000000000105cbc>] dump_stack+0x30/0x40
[<000000000012a0c8>] __schedule_bug+0x84/0x94
[<000000000056234e>] schedule+0x5ea/0x970
[<0000000000477cd2>] __sclp_vt220_write+0x1f6/0x3ec
[<0000000000477f00>] sclp_vt220_con_write+0x38/0x48
[<0000000000130b4a>] __call_console_drivers+0xbe/0xd8
[<0000000000130bf0>] _call_console_drivers+0x8c/0xd0
[<0000000000130eea>] release_console_sem+0x1a6/0x2fc
[<0000000000131786>] vprintk+0x262/0x480
[<00000000001319fa>] printk+0x56/0x68
[<0000000000125aaa>] print_cfs_rq+0x45e/0x4a4
[<000000000012614e>] sched_debug_show+0x65e/0xee8
[<000000000012a8fc>] show_state_filter+0x1cc/0x1f0
[<000000000044d39c>] sysrq_handle_showstate+0x2c/0x3c
[<000000000044d1fe>] __handle_sysrq+0xae/0x18c
[<00000000002001f2>] write_sysrq_trigger+0x8a/0x90
[<00000000001f7862>] proc_reg_write+0x9a/0xc4
[<00000000001a83d4>] vfs_write+0xb8/0x174
[<00000000001a8b88>] sys_write+0x58/0x8c
[<0000000000112e7c>] sysc_noemu+0x10/0x16
[<0000020000116f68>] 0x20000116f68
The problem seems to be, that with a full console buffer, release_console_sem
disables interrupts with spin_lock_irqsave and then calls the console function
without enabling interrupts. __sclp_vt220_write checks for in_interrupt, to
decide if it can schedule. It should check for in_atomic instead.
The same is true for sclp_tty.c.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch converts s390 to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interfaces of internal functions below are changed:
o dasd_end_request
o tapeblock_end_request
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
single list_head variable initialized with LIST_HEAD_INIT could almost
always can be replaced with LIST_HEAD declaration, this shrinks the code
and looks better.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It caused only a lot of confusion. From now on cpu hotplug of up to
NR_CPUS will work by default. If somebody wants to limit that then
the possible_cpus parameter can be used.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a new interface so that cpus can be put into standby state and
configured state.
Only offline cpus can be put into standby state or configured state.
For that the new percpu sysfs attribute "configure" must be used.
To put a cpu in standby state a "0" must be written to the attribute.
In order to switch it into configured state a "1" must be written to
the attribute.
Only cpus in configured state can be brought online.
In addition this patch introduces a static mapping of physical to
logical cpus. As a result only the sysfs directories of present cpus
will be created. To scan for new cpus the new sysfs attribute "rescan"
must be used.
Writing to /sys/devices/system/cpu/rescan will trigger a rescan of
cpus and will create directories for new cpus.
On IPL only configured cpus will be used. And on reboot/shutdown all
cpus will remain in their current state (configured/standby).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace all lock_cpu_hotplug/unlock_cpu_hotplug from the kernel and use
get_online_cpus and put_online_cpus instead as it highlights the
refcount semantics in these operations.
The new API guarantees protection against the cpu-hotplug operation, but
it doesn't guarantee serialized access to any of the local data
structures. Hence the changes needs to be reviewed.
In case of pseries_add_processor/pseries_remove_processor, use
cpu_maps_update_begin()/cpu_maps_update_done() as we're modifying the
cpu_present_map there.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Convert struct class_device users under drivers/s390/char to use
struct device.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
There have been issues with non-latin1 diacritics and unicode.
http://bugzilla.kernel.org/show_bug.cgi?id=7746
Git 759448f459 `Kernel utf-8 handling'
partly resolved it by adding conversion between diacritics and
unicode. The patch below goes further by just turning diacritics into
unicode, hence providing better future support. The kbd support can be
fetched from
http://bugzilla.kernel.org/attachment.cgi?id=12313
This was tested in all of latin1, latin9, latin2 and unicode with french
and czech dead keys.
Turn the kernel accent_table into unicode, and extend ioctls KDGKBDIACR
and KDSKBDIACR into their equivalents KDGKBDIACRUC and KDSKBDIACR.
New function int conv_uni_to_8bit(u32 uni) for converting unicode into 8bit
_input_. No, we don't want to store the translation, as it is potentially
sparse and large.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Jan Engelhardt <jengelh@gmx.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The early console device is special as it already has all needed data
set and raw3215[0] allocated from con3215_init(). Therefore, it needs
special treatment in the probe function so it can be matched with the
3215 driver which is already owning it.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Constraint for err is wrong since it is preinitialized and the code
relies on it in case of an exception.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently there are situations, where the tape medium state (loaded, unloaded,
unknown) is not set correctly. The reason is that the medium association
field is used to determine the medium state. This not always leads to
correct results. To fix that we use another field of the medium sense
data instead.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
memcpy_real uses the mvcle instruction. This instruction alters all used
registers (source, destination and 2 x count). Therefore we have to flag
those registers as input/output registers (+d). In addition to that, we
have to specify, that we read from memory designated by "src" and write to
memory designated by "dest".
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Also removes a bunch of ^L in drivers/s390/cio/cmf.c
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Every usage of rq_for_each_bio wraps a usage of
bio_for_each_segment, so these can be combined into
rq_for_each_segment.
We define "struct req_iterator" to hold the 'bio' and 'index' that
are needed for the double iteration.
Signed-off-by: Neil Brown <neilb@suse.de>
Various compile fixes by me...
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When a vmur device is removed due to a detach of the device, currently the
ur device structure is freed. Unfortunately it can happen, that there is
still a user of the device structure, when the character device is open
during the detach process. To fix this, reference counting for the vmur
structure is introduced.
In addition to that, the online, offline, probe and remove functions are
serialized now using a global mutex.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
There are several s390 diagnose calls, which must be executed below the
2GB memory boundary. In order to enforce this, those diagnoses must be
compiled into the kernel. Currently diag 14 can be called within the
vmur kernel module from addresses above 2GB. This leads to specification
exceptions. This patch moves diag10, diag14 and diag210 into the new
diag.c file.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Locking added so that multithreaded applications can now do writes
from different threads without the risk of storage corruption.
Signed-off-by: Melissa Howland <melissah@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If memory buffers above 2GB are used, diagnose 14 raises a specification
exception. This fix ensures that buffer allocation is done below the 2GB
boundary.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the z/VM reader is already open, it can happen that after opening the
Linux reader device, not the topmost file is processed. According the
semantics of the Linux z/VM unit record device driver, always the topmost
file has to be processed. With this fix an error is returned if that is
not the case.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a reader file with HOLD status is at the top of the reader queue, currently
all read requests will return data of the second file in the queue. But the
semantics of vmur is that always the topmost file is read. With this fix
-EPERM is returned on open, if the topmost reader file is in HOLD status.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
vmur allocates one contiguous kernel buffer to copy user data when creating
ccw programs for punch or printer. If big block sizes are used, under memory
pressure it can happen, that we do not get memory in one chunk. Now we
allocate memory for each single record to avoid high order allocations.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Also convert to slab_is_available() as an indicator if
get_zeroed_page() will work or not.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Record length of spool file must be only stored in 1st SPLINK record
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
z/VM Unit record character device driver to access VM reader, punch,
and printer.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A number of small changes to vmcp:
- Change preferred email address.
- Use PRINT_xxx machros from debug.h like most s390 drivers, define
"vmcp:" as PRINTK_HEADER and wrap error message at column 80.
- Add error number to error message.
- Update copyright, as I touched this file.
- Small whitespace diff.
- Use mutex instead of semaphore (Thanks Heiko for the patch)
- Don't register debug feature on failure.
- Check debug feature registration on init to avoid a potential oops
on unload if the debug feature could not be registered--> 2 more
messages.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use __init and __exit for vmlogrdr. Both functions are only referenced
by the module_init exit macros, so this change should be fine.
Acked-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Check if a command is available before executing. Saves some
superfluous service calls that won't succeed anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce some new interfaces so that random subsystems don't have to
mess around with sclp internal structures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
No need to use the "&" prefix and, since you're calling nonseekable_open(),
there is no need to use no_llseek().
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Added members for volume number and real memory size to header information.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Disband drivers/s390/Kconfig, use the common Kconfig files. The s390
specific config options from drivers/s390/Kconfig are moved to the
respective common Kconfig files.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The function shouldn't have existed in the first place (not MSS-aware).
Introduce a new function ccw_device_get_id() that extracts the
ccw_dev_id structure of a ccw device and convert all users of
_ccw_device_get_device_number to ccw_device_get_id.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Instead of the deprecated read_conf_data(), implement a new function
tape_3590_read_dev_chars().
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Generate uevents for all cpus if cpu capability changes. This can
happen e.g. because the cpus are overheating. The cpu capability can
be read via /sys/devices/system/cpu/cpuN/capability.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Use only capital letters for defines.
Cc: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reopen of /dev/account failed. The IUCV path has to be terminated
in vmlogrdr_release.
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add explicit sclp initialization for those sclp users that do not
register with the interface.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s390 machines provide hardware support for creating Linux dumps on SCSI
disks. For creating a dump a special purpose dump Linux is used. The first
32 MB of memory are saved by the hardware before the dump Linux is
booted. Via an SCLP interface, the saved memory can be accessed from
Linux. This patch exports memory and registers of the crashed Linux to
userspace via a debugfs file. For more information refer to
Documentation/s390/zfcpdump.txt, which is included in this patch.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
We get this:
Section mismatch: reference to .init.text:con3270_consetup from .data
between 'con3270' (at offset 0x45c8) and 'con3270_fn'
Section mismatch: reference to .init.text:con3215_consetup from .data
between 'con3215' (at offset 0x4678) and
'raw3215_ccw_driver'
Since there is no difference between a non present console setup
function and one that returns only 0 remove them.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Frank Munzert