On a system where there are no hot pluggable cpus "additional_cpus"
is still set to -1 at the point where we call per_cpu_scan_finalize().
If we didn't find an SRAT table and so pick the default "32" for the
number of cpus, when we get to:
high_cpu = min(high_cpu + reserve_cpus, NR_CPUS);
we will end up initializing for just 31 cpus ... and so we will
die horribly when bringing up cpu#32.
Problem introduced by: 2c6e6db41f
"Minimize per_cpu reservations."
Acked-by: Robin Holt <holt@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This driver supports video input devices compliant with the USB Video Class
specification. This means lots of currently manufactured webcams, and probably
most of the future ones.
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some SoCs need a different chip_delay value.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Cardbus connector does not have an IDSEL signal, and Cardbus
cards are always the intended target of configuration transactions
on their local PCI bus. This means that if the Orion's PCI bus
signals are hooked up to a Cardbus slot, the same set of PCI
functions will will appear 31 times, for each of the PCI device
IDs 1-31 (ID 0 is the host bridge).
This patch adds a function to the Orion PCI handling code that board
support code can call to enable Cardbus mode. When Cardbus mode is
enabled, configuration transactions on the PCI local bus are only
allowed to PCI IDs 0 (host bridge) and 1 (cardbus device).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch makes mac80211 refuse a WEP key whose length is not WEP40 nor
WEP104.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite AID calculation in handle_pspoll() to avoid truncating bits.
Make hostap_80211_header_parse() static, don't export it. Avoid
shadowing variables.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DEBUG_EXTRA is reported to the kernel log by default, but DEBUG_EXTRA2
is not. Unrelated WDS frames pollute the log unnecessarily.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current logic has a bug which cannot find matching pattern, if the
pattern is matched from the first character of target string.
for example:
pattern=abc, string=abcdefg
pattern=a, string=abcdefg
Searching algorithm should return 0 for those things.
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lost connections was reported by Thomas Bätzler (running 2.6.25 kernel) on
the netfilter mailing list (see the thread "Weird nat/conntrack Problem
with PASV FTP upload"). He provided tcpdump recordings which helped to
find a long lingering bug in conntrack.
In TCP connection tracking, checking the lower bound of valid ACK could
lead to mark valid packets as INVALID because:
- We have got a "higher or equal" inequality, but the test checked
the "higher" condition only; fixed.
- If the packet contains a SACK option, it could occur that the ACK
value was before the left edge of our (S)ACK "window": if a previous
packet from the other party intersected the right edge of the window
of the receiver, we could move forward the window parameters beyond
accepting a valid ack. Therefore in this patch we check the rightmost
SACK edge instead of the ACK value in the lower bound of valid (S)ACK
test.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows booting Kirkwood with the L2 in writeback mode,
by reading the WT override bit from the L2 config register and
passing that into the Feroceon L2 init routine, instead of assuming
that the WT override bit will always be set
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
In some cases, compilation of the tsx09 common file was failing due
to an incomplete list of includes.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
After Jean Delvare's change "i2c: Convert most new-style drivers
to use module aliasing" (3760f73671),
loading rtc-xxx from platform code fails. Update mv2120-setup.c so
that the driver is loaded correctly.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Kurobox Pro/Linkstation Pro devices use a microcontroller connected
to UART1. As most of the communication with this microcontroller is
done from userland (power button detection, fan speed ...), the setup
file has to make UART1 available from userland.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Now that we support warm-plug mate port will be registered
even if there are no devices attached to it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This reverts commit ac1623625c.
It was premature to remove it now, we will do it post-2.6.26.
Thanks to Russell King for noticing the issue.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch annotates the platform_secondary_init function in
arch/arm/mach-realview/platsmp.c with trace_hardirqs_off to avoid a
warning when LOCKDEP and TRACE_IRQFLAGS are enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptrace GET/SET FPXREGS broken
x86: fix cpu hotplug crash
x86: section/warning fixes
x86: shift bits the right way in native_read_tscp
The newly added event_lock spinlock in the input core disallows sleeping
and therefore using mutexes in event handlers. Convert force-feedback
core to rely on event_lock instead of mutex to protect slots allocated
for fore-feedback effects. The original mutex is still used to serialize
uploading and erasing of effects.
Reported-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds the Repeat key to the input layer. The usage
in the HUT is 0xBC (listed under "15.7 Transport Controls").
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When I update kernel 2.6.25 from 2.6.24, gdb does not work.
On 2.6.25, ptrace(PTRACE_GETFPXREGS, ...) returns ENODEV.
But 2.6.24 kernel's ptrace() returns EIO.
It is issue of compatibility.
I attached test program as pt.c and patch for fix it.
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <signal.h>
#include <errno.h>
#include <sys/ptrace.h>
#include <sys/types.h>
struct user_fxsr_struct {
unsigned short cwd;
unsigned short swd;
unsigned short twd;
unsigned short fop;
long fip;
long fcs;
long foo;
long fos;
long mxcsr;
long reserved;
long st_space[32]; /* 8*16 bytes for each FP-reg = 128 bytes */
long xmm_space[32]; /* 8*16 bytes for each XMM-reg = 128 bytes */
long padding[56];
};
int main(void)
{
pid_t pid;
pid = fork();
switch(pid){
case -1:/* error */
break;
case 0:/* child */
child();
break;
default:
parent(pid);
break;
}
return 0;
}
int child(void)
{
ptrace(PTRACE_TRACEME);
kill(getpid(), SIGSTOP);
sleep(10);
return 0;
}
int parent(pid_t pid)
{
int ret;
struct user_fxsr_struct fpxregs;
ret = ptrace(PTRACE_GETFPXREGS, pid, 0, &fpxregs);
if(ret < 0){
printf("%d: %s.\n", errno, strerror(errno));
}
kill(pid, SIGCONT);
wait(pid);
return 0;
}
/* in the kerel, at kernel/i387.c get_fpxregs() */
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Vegard Nossum reported crashes during cpu hotplug tests:
http://marc.info/?l=linux-kernel&m=121413950227884&w=4
In function _cpu_up, the panic happens when calling
__raw_notifier_call_chain at the second time. Kernel doesn't panic when
calling it at the first time. If just say because of nr_cpu_ids, that's
not right.
By checking the source code, I found that function do_boot_cpu is the culprit.
Consider below call chain:
_cpu_up=>__cpu_up=>smp_ops.cpu_up=>native_cpu_up=>do_boot_cpu.
So do_boot_cpu is called in the end. In do_boot_cpu, if
boot_error==true, cpu_clear(cpu, cpu_possible_map) is executed. So later
on, when _cpu_up calls __raw_notifier_call_chain at the second time to
report CPU_UP_CANCELED, because this cpu is already cleared from
cpu_possible_map, get_cpu_sysdev returns NULL.
Many resources are related to cpu_possible_map, so it's better not to
change it.
Below patch against 2.6.26-rc7 fixes it by removing the bit clearing in
cpu_possible_map.
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Tested-by: Vegard Nossum <vegard.nossum@gmail.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (42 commits)
V4L/DVB (8108): Fix open/close race in saa7134
V4L/DVB (8100): V4L/vivi: fix possible memory leak in vivi_fillbuff
V4L/DVB (8097): xc5000: check device hardware state to determine if firmware download is needed
V4L/DVB (8096): au8522: prevent false-positive lock status
V4L/DVB (8092): videodev: simplify and fix standard enumeration
V4L/DVB (8075): stv0299: Uncorrected block count and bit error rate fixed
V4L/DVB (8074): av7110: OSD transfers should not be interrupted
V4L/DVB (8073): av7110: Catch another type of ARM crash
V4L/DVB (8071): tda10023: Fix possible kernel oops during initialisation
V4L/DVB (8069): cx18: Fix S-Video and Compsite inputs for the Yuan MPC718 and enable card entry
V4L/DVB (8068): cx18: Add I2C slave reset via GPIO upon initialization
V4L/DVB (8067): cx18: Fix firmware load for case when digital capture happens first
V4L/DVB (8066): cx18: Fix audio mux input definitions for HVR-1600 Line In 2 and FM radio
V4L/DVB (8063): cx18: Fix unintended auto configurations in cx18-av-core
V4L/DVB (8061): cx18: only select tuner / frontend modules if !DVB_FE_CUSTOMISE
V4L/DVB (8048): saa7134: Fix entries for Avermedia A16d and Avermedia E506
V4L/DVB (8044): au8522: tuning optimizations
V4L/DVB (8043): au0828: add support for additional USB device id's
V4L/DVB (8042): DVB-USB UMT-010 channel scan oops
V4L/DVB (8040): soc-camera: remove soc_camera_host_class class
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
dock: bay: Don't call acpi_walk_namespace() when ACPI is disabled.
ACPI: don't walk tables if ACPI was disabled
thermal: Create CONFIG_THERMAL_HWMON=n
Removed vmlinux* rule because it matches too many useful files, replacing
it with rules matching filetype by filename (e.g. *.gz). Also unignored
.mailmap from the top directory. Added a comment telling the user how to
check for tracked files being ignored.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'audit.b52' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] remove useless argument type in audit_filter_user()
[PATCH] audit: fix kernel-doc parameter notation
[PATCH] kernel/audit.c: nlh->nlmsg_type is gotten more than once
the CPU hotplug problems (crashes under high-volume unplug+replug
tests) seem to be related to migrate_dead_tasks().
Firstly I added traces to see all tasks being migrated with
migrate_live_tasks() and migrate_dead_tasks(). On my setup the problem
pops up (the one with "se == NULL" in the loop of
pick_next_task_fair()) shortly after the traces indicate that some has
been migrated with migrate_dead_tasks()). btw., I can reproduce it
much faster now with just a plain cpu down/up loop.
[disclaimer] Well, unless I'm really missing something important in
this late hour [/desclaimer] pick_next_task() is not something
appropriate for migrate_dead_tasks() :-)
the following change seems to eliminate the problem on my setup
(although, I kept it running only for a few minutes to get a few
messages indicating migrate_dead_tasks() does move tasks and the
system is still ok)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The commit 77d16f450a ("[IPV6] ROUTE:
Unify RT6_F_xxx and RT6_SELECT_F_xxx flags") intended to pass various
routing lookup hints around RT6_LOOKUP_F_xxx flags, but conversion was
missing for rt6_device_match().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a missing "!" in a conditional statement which is causing entries to
be skipped when dumping the default IPv6 static label entries. This can be
demonstrated by running the following:
# netlabelctl unlbl add default address:::1 \
label:system_u:object_r:unlabeled_t:s0
# netlabelctl -p unlbl list
... you will notice that the entry for the IPv6 localhost address is not
displayed but does exist (works correctly, causes collisions when attempting
to add duplicate entries, etc.).
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an SKB cannot be chained to a session, the current code attempts
to "restore" its ip_summed field from lro_mgr->ip_summed. However,
lro_mgr->ip_summed does not hold the original value; in fact, we'd
better not touch skb->ip_summed since it is not modified by the code
in the path leading to a failure to chain it. Also use a cleaer
comment to the describe the ip_summed field of struct net_lro_mgr.
Issue raised by Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem is that while we work w/o the inet_frags.lock even
read-locked the secret rebuild timer may occur (on another CPU, since
BHs are still disabled in the inet_frag_find) and change the rnd seed
for ipv4/6 fragments.
It was caused by my patch fd9e63544c
([INET]: Omit double hash calculations in xxx_frag_intern) late
in the 2.6.24 kernel, so this should probably be queued to -stable.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got a problem when I wanted to check if the kernel supports process
event connector, and It seems there's no way to do this check.
At best I can check if the kernel supports connector or not, by looking
into /proc/net/netlink, or maybe checking the return value of bind() to
see if it's ENOENT.
So it would be useful to add /proc/net/connector to list all supported
connectors:
# cat /proc/net/connector
Name ID
connector 4294967295:4294967295
cn_proc 1:1
w1 3:1
Changelog:
- fix memory leak: s/seq_release/single_release
- use spin_lock_bh instead of spin_lock_irqsave
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some doc comments to match function and attribute names in
net/netlink/attr.c.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found another case where we are sending information to userspace
in the wrong HZ scale. This should have been fixed back in 2.5 :-(
This means an ABI change but as it stands there is no way for an application
like ss to get the right value.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the CONFIG_'s the value is anyway not correct in userspace.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d62733c8e4
([SCHED]: Qdisc changes and sch_rr added for multiqueue)
added a NET_SCH_RR option that was unused since the code
went unconditionally into sch_prio.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note, in the following patch, 'err' is initialized as:
int err = -ENOBUFS;
Signed-off-by: WANG Cong <wcong@critical-links.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For n:1 'datagram connections' (eg /dev/log), the unix_dgram_sendmsg
routine implements a form of receiver-imposed flow control by
comparing the length of the receive queue of the 'peer socket' with
the max_ack_backlog value stored in the corresponding sock structure,
either blocking the thread which caused the send-routine to be called
or returning EAGAIN. This routine is used by both SOCK_DGRAM and
SOCK_SEQPACKET sockets. The poll-implementation for these socket types
is datagram_poll from core/datagram.c. A socket is deemed to be
writeable by this routine when the memory presently consumed by
datagrams owned by it is less than the configured socket send buffer
size. This is always wrong for PF_UNIX non-stream sockets connected to
server sockets dealing with (potentially) multiple clients if the
abovementioned receive queue is currently considered to be full.
'poll' will then return, indicating that the socket is writeable, but
a subsequent write result in EAGAIN, effectively causing an (usual)
application to 'poll for writeability by repeated send request with
O_NONBLOCK set' until it has consumed its time quantum.
The change below uses a suitably modified variant of the datagram_poll
routines for both type of PF_UNIX sockets, which tests if the
recv-queue of the peer a socket is connected to is presently
considered to be 'full' as part of the 'is this socket
writeable'-checking code. The socket being polled is additionally
put onto the peer_wait wait queue associated with its peer, because the
unix_dgram_recvmsg routine does a wake up on this queue after a
datagram was received and the 'other wakeup call' is done implicitly
as part of skb destruction, meaning, a process blocked in poll
because of a full peer receive queue could otherwise sleep forever
if no datagram owned by its socket was already sitting on this queue.
Among this change is a small (inline) helper routine named
'unix_recvq_full', which consolidates the actual testing code (in three
different places) into a single location.
Signed-off-by: Rainer Weikusat <rweikusat@mssgmbh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an skb has nr_frags set to zero but its frag_list is not empty (as
it can happen if software LRO is enabled), and a previous
tcp_read_sock has consumed the linear part of the skb, then
__skb_splice_bits:
(a) incorrectly reports an error and
(b) forgets to update the offset to account for the linear part
Any of the two problems will cause the subsequent __skb_splice_bits
call (the one that handles the frag_list skbs) to either skip data,
or, if the unadjusted offset is greater then the size of the next skb
in the frag_list, make tcp_splice_read loop forever.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Luck