Set per-plane global alpha to maximum value to get proper blending of
XRGB and ARGB planes. This fixes the strange order of overlapping planes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DMA hardware should respect buffer pitch, so use the width calculated from
the buffer pitch instead of the virtual one.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fix following issues related to planar YUV pixel format configuration:
- NV16/61 modes were incorrectly programmed as NV12/21,
- YVU420 was programmed as YUV420 on source,
- YVU420 and YUV422 were programmed as YUV420 on output.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Horizontal (DRM_MODE_REFLECT_Y) and vertical (DMR_MODE_REFLECT_Y) flip
were swapped in GScaler driver. Fix this by swapping code for interpreting
them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Investigation revealed that GScaler hardware requires the real buffer width
(pitch) to be aligned to 16 pixels.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DMA hardware should respect buffer pitch, so use the width calculated from
the buffer pitch instead of the virtual one.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fix Cb/CR components order in two-planar YUV420, YUV422 and YUV444 modes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Ensure that Scaler hardware is properly reset and interrupts are cleared
before processing next image.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Horizontal (DRM_MODE_REFLECT_Y) and vertical (DMR_MODE_REFLECT_Y) flip
were swapped in Rotator driver. Fix this by swapping code for interpreting
them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Prepare a common function for size and scale checks and call it for
source and destination buffers. Then also move there the state-less checks
from exynos_drm_ipp_task_setup_buffer, so the format information is already
available in limits processing. Finally perform the IPP_LIMIT_BUFFER check
on the real width of the buffer (the width calculated from the provided
buffer pitch).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Merge fixups for the recent extenstion of the generic power domains
(genpd) framework covering performance states.
* pm-domains:
PM / Domains: Rename opp_node to np
PM / Domains: Fix return value of of_genpd_opp_to_performance_state()
At the very least we should check the return value if
nla_parse_nested() is called with a non-NULL policy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 9757235f45, "nl80211: correct checks for
NL80211_MESHCONF_HT_OPMODE value") relaxed the range for the HT
operation field in meshconf, while also adding checks requiring
the non-greenfield and non-ht-sta bits to be set in certain
circumstances. The latter bit is actually reserved for mesh BSSes
according to Table 9-168 in 802.11-2016, so in fact it should not
be set.
wpa_supplicant sets these bits because the mesh and AP code share
the same implementation, but authsae does not. As a result, some
meshconf updates from authsae which set only the NONHT_MIXED
protection bits were being rejected.
In order to avoid breaking userspace by changing the rules again,
simply accept the values with or without the bits set, and mask
off the reserved bit to match the spec.
While in here, update the 802.11-2012 reference to 802.11-2016.
Fixes: 9757235f45 ("nl80211: correct checks for NL80211_MESHCONF_HT_OPMODE value")
Cc: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Reviewed-by: Masashi Honma <masashi.honma@gmail.com>
Reviewed-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On pre-emption enabled kernels the following print was being seen due to
missing local_bh_disable/local_bh_enable calls. mac80211 assumes that
pre-emption is disabled in the data path.
BUG: using smp_processor_id() in preemptible [00000000] code: iwd/517
caller is __ieee80211_subif_start_xmit+0x144/0x210 [mac80211]
[...]
Call Trace:
dump_stack+0x5c/0x80
check_preemption_disabled.cold.0+0x46/0x51
__ieee80211_subif_start_xmit+0x144/0x210 [mac80211]
Fixes: 9118064914 ("mac80211: Add support for tx_control_port")
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[commit message rewrite, fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It seems that during the conversion from gpio* to gpiod*, the initial
state of SCL was wrongly switched to LOW. Fix it to be HIGH again.
Fixes: 7bb75029ef ("i2c: gpio: Enforce open drain through gpiolib")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
If DMA safe memory was allocated, but the subsequent I2C transfer
fails the memory is leaked. Plug this leak.
Fixes: 8a77821e74 ("i2c: smbus: use DMA safe buffers for emulated SMBus transactions")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
So, if somebody wants to re-implement this in the future, we pinpoint to
a problem case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This reverts commit 3e5f06bed7. As per
bugzilla #200045, this caused a regression. I don't really see a way to
fix it without having the hardware. So, revert the patch and I will fix
the issue I was seeing originally in the i2c-gpio driver itself. I
couldn't find new users of this algorithm since, so there should be no
one depending on the new behaviour.
Reported-by: Sergey Larin <cerg2010cerg2010@mail.ru>
Fixes: 3e5f06bed7 ("i2c: algo-bit: init the bus to a known state")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Sergey Larin <cerg2010cerg2010@mail.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
If a user is accessing a file in selinuxfs with a pointer to a userspace
buffer that is backed by e.g. a userfaultfd, the userspace access can
stall indefinitely, which can block fsi->mutex if it is held.
For sel_read_policy(), remove the locking, since this method doesn't seem
to access anything that requires locking.
For sel_read_bool(), move the user access below the locked region.
For sel_write_bool() and sel_commit_bools_write(), move the user access
up above the locked region.
Cc: stable@vger.kernel.org
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
[PM: removed an unused variable in sel_read_policy()]
Signed-off-by: Paul Moore <paul@paul-moore.com>
For ACLs implemented using either FIB rules or FIB entries, the BPF
program needs the FIB lookup status to be able to drop the packet.
Since the bpf_fib_lookup API has not reached a released kernel yet,
change the return code to contain an encoding of the FIB lookup
result and return the nexthop device index in the params struct.
In addition, inform the BPF program of any post FIB lookup reason as
to why the packet needs to go up the stack.
The fib result for unicast routes must have an egress device, so remove
the check that it is non-NULL.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Flag with FLAG_EXPECTED_FAIL the BPF_MAXINSNS tests that cannot be jited
on s390 because they exceed BPF_SIZE_MAX and fail when
CONFIG_BPF_JIT_ALWAYS_ON is set. Also set .expected_errcode to -ENOTSUPP
so the tests pass in that case.
Signed-off-by: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The other day I was testing one of the HP laptops at my office with an
i915/amdgpu hybrid setup and noticed that hotplugging was non-functional
on almost all of the display outputs. I eventually discovered that all
of the external outputs were connected to the amdgpu device instead of
i915, and that the hotplugs weren't being detected so long as the GPU
was in runtime suspend. After some talking with folks at AMD, I learned
that amdgpu is actually supposed to support hotplug detection in runtime
suspend so long as the OEM has implemented it properly in the firmware.
On this HP ZBook 15 G4 (the machine in question), amdgpu wasn't managing
to find the ATIF handle at all despite the fact that I could see acpi
events being sent in response to any hotplugging. After going through
dumps of the firmware, I discovered that this machine did in fact
support ATIF, but that it's ATIF method lived in an entirely different
namespace than this device's handle (the device handle was
\_SB_.PCI0.PEG0.PEGP, but ATIF lives in ATPX's handle at
\_SB_.PCI0.GFX0).
So, fix this by probing ATPX's ACPI parent's namespace if we can't find
ATIF elsewhere, along with storing a pointer to the proper handle to use
for ATIF and using that instead of the device's handle.
This fixes HPD detection while in runtime suspend for this ZBook!
v2: Update the comment to reflect how the namespaces are arranged
based on the system configuration. (Alex)
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Since it seems that some vendors are storing the ATIF ACPI methods under
the same handle that ATPX lives under instead of the device's own
handle, we're going to need to be able to retrieve this handle later so
we can probe for ATIF there.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Currently, there is nothing in amdgpu that actually uses these structs
other than amdgpu_acpi.c. Additionally, since we're about to start
saving the correct ACPI handle to use for calling ATIF in this struct
this saves us from having to handle making sure that the acpi_handle
(and by proxy, the type definition for acpi_handle and all of the other
acpi headers) doesn't need to be included within the amdgpu_drv struct
itself. This follows the example set by amdgpu_atpx_handler.c.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
- A single fix in meson for an unhandled error path in meson_drv_bind_master().
-----BEGIN PGP SIGNATURE-----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=zPj3
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-06-28' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v4.18-rc3:
- A single fix in meson for an unhandled error path in meson_drv_bind_master().
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fa740f31-5a8d-ed45-5e8a-aecd3f6f11b7@linux.intel.com
A few fixes for 4.18:
- fix a read past the end of an array due to vega20 changes
- fix driver on systems with non-4K pages
- fix locking with pageflipping in DC that could lead to a sleep while atomic
- fix VCN firmware version reporting for upcoming firmware
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628032641.2765-1-alexander.deucher@amd.com
Currently device_supports_dax() just checks to see if the QUEUE_FLAG_DAX
flag is set on the device's request queue to decide whether or not the
device supports filesystem DAX. Really we should be using
bdev_dax_supported() like filesystems do at mount time. This performs
other tests like checking to make sure the dax_direct_access() path works.
We also explicitly clear QUEUE_FLAG_DAX on the DM device's request queue if
any of the underlying devices do not support DAX. This makes the handling
of QUEUE_FLAG_DAX consistent with the setting/clearing of most other flags
in dm_table_set_restrictions().
Now that bdev_dax_supported() explicitly checks for QUEUE_FLAG_DAX, this
will ensure that filesystems built upon DM devices will only be able to
mount with DAX if all underlying devices also support DAX.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Fixes: commit 545ed20e6d ("dm: add infrastructure for DAX support")
Cc: stable@vger.kernel.org
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add an explicit check for QUEUE_FLAG_DAX to __bdev_dax_supported(). This
is needed for DM configurations where the first element in the dm-linear or
dm-stripe target supports DAX, but other elements do not. Without this
check __bdev_dax_supported() will pass for such devices, letting a
filesystem on that device mount with the DAX option.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Mike Snitzer <snitzer@redhat.com>
Fixes: commit 545ed20e6d ("dm: add infrastructure for DAX support")
Cc: stable@vger.kernel.org
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
QUEUE_FLAG_DAX is an indication that a given block device supports
filesystem DAX and should not be set for PMEM namespaces which are in "raw"
mode. These namespaces lack struct page and are prevented from
participating in filesystem DAX as of commit 569d0365f5 ("dax: require
'struct page' by default for filesystem dax").
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Mike Snitzer <snitzer@redhat.com>
Fixes: 569d0365f5 ("dax: require 'struct page' by default for filesystem dax")
Cc: stable@vger.kernel.org
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
During assemble, the spare marked for replacement is not checked.
conf->fullsync cannot be updated to be 1. As a result, recovery will
treat it as a clean array. All recovering sectors are skipped. Original
device is replaced with the not-recovered spare.
mdadm -C /dev/md0 -l10 -n4 -pn2 /dev/loop[0123]
mdadm /dev/md0 -a /dev/loop4
mdadm /dev/md0 --replace /dev/loop0
mdadm -S /dev/md0 # stop array during recovery
mdadm -A /dev/md0 /dev/loop[01234]
After reassemble, you can see recovery go on, but it completes
immediately. In fact, recovery is not actually processed.
To solve this problem, we just add the missing logics for replacment
spares. (In raid1.c or raid5.c, they have already been checked.)
Reported-by: Alex Chen <alexchen@synology.com>
Reviewed-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Signed-off-by: Shaohua Li <shli@fb.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=yyKY
-----END PGP SIGNATURE-----
Merge tag 'printk-for-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk fix from Petr Mladek:
"Revert a commit that went in by mistake. I already have a better fix
in the queue for 4.19"
* tag 'printk-for-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
Revert "lib/test_printf.c: call wait_for_random_bytes() before plain %p tests"
Over a dozen of changes, but all small and clear fixes.
A half of them are the regression fixes for CA0132 HD-audio codec,
and the rest are, again, a few more fixups for HD-audio, two UBSAN
fixes in the core ioctls, and a trivial fix in the error path
handling in lx6464es driver.
-----BEGIN PGP SIGNATURE-----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=yeOb
-----END PGP SIGNATURE-----
Merge tag 'sound-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Over a dozen changes, but all small and clear fixes.
Half of them are the regression fixes for CA0132 HD-audio codec, and
the rest are, again, a few more fixups for HD-audio, two UBSAN fixes
in the core ioctls, and a trivial fix in the error path handling in
lx6464es driver"
* tag 'sound-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Fix UBSAN warning at SNDRV_SEQ_IOCTL_QUERY_NEXT_CLIENT ioctl
ALSA: timer: Fix UBSAN warning at SNDRV_TIMER_IOCTL_NEXT_DEVICE ioctl
ALSA: hda/realtek - Fix the problem of two front mics on more machines
ALSA: hda/realtek - Add a quirk for FSC ESPRIMO U9210
ALSA: hda/ca0132: make array ca0132_alt_chmaps static
ALSA: hda - Force to link down at runtime suspend on ATI/AMD HDMI
ALSA: lx6464es: Missing error code in snd_lx6464es_create()
ALSA: hda/ca0132: Fix DMic data rate for Alienware M17x R4
ALSA: hda/ca0132: Restore PCM Analog Mic-In2
ALSA: hda/ca0132: Don't test for QUIRK_NONE
ALSA: hda/ca0132: Restore behavior of QUIRK_ALIENWARE
ALSA: hda/ca0132: Delete redundant UNSOL event requests
ALSA: hda/ca0132: Delete pointless assignments to struct auto_pin_cfg fields
ALSA: hda/realtek - Fix pop noise on Lenovo P50 & co
- Add a quirk for a bunch of broken Macronix chips
- Fix nand_block_bad() when chip->ecc.read_oob() returns a positive
value encoding the number of bitflips
- Fix OOB handling in the MXC driver fo V2.1 controllers
- Flag the ONFI_FEATURE_ON_DIE_ECC as supported in the Micron driver
- Hardcode clk rate in the denali_dt driver to address a bad DT
representation (the proper fix will be queued for 4.19)
SPI NOR fixes:
- Add an ULL constant to some ID definitions so that the ID is not
truncated on 32-bit platforms
MTD fixes:
- Fix the sector unlocking logic in the CFI driver
-----BEGIN PGP SIGNATURE-----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=BjBU
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-4.18-rc3' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Boris Brezillon:
"NAND fixes:
- add a quirk for a bunch of broken Macronix chips
- fix nand_block_bad() when chip->ecc.read_oob() returns a positive
value encoding the number of bitflips
- fix OOB handling in the MXC driver fo V2.1 controllers
- flag the ONFI_FEATURE_ON_DIE_ECC as supported in the Micron driver
- hardcode clk rate in the denali_dt driver to address a bad DT
representation (the proper fix will be queued for 4.19)
SPI NOR fixes:
- add an ULL constant to some ID definitions so that the ID is not
truncated on 32-bit platforms
MTD fixes:
- fix the sector unlocking logic in the CFI driver"
* tag 'mtd/fixes-for-4.18-rc3' of git://git.infradead.org/linux-mtd:
mtd: rawnand: denali_dt: set clk_x_rate to 200 MHz unconditionally
mtd: dataflash: Use ULL suffix for 64-bit constants
mtd: cfi_cmdset_0002: Avoid walking all chips when unlocking.
mtd: cfi_cmdset_0002: Fix unlocking requests crossing a chip boudary
mtd: cfi_cmdset_0002: fix SEGV unlocking multiple chips
mtd: cfi_cmdset_0002: Use right chip in do_ppb_xxlock()
mtd: rawnand: All AC chips have a broken GET_FEATURES(TIMINGS).
mtd: rawnand: fix return value check for bad block status
mtd: rawnand: mxc: set spare area size register explicitly
mtd: rawnand: micron: add ONFI_FEATURE_ON_DIE_ECC to supported features
A new member Vr2_I2C_address is added.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The vbios firmware structure changed between v3_1 and v3_2. So,
the code to setup bootup values needs different paths based
on header version.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Thermal support is enabled on vega12.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Merge fixes from Andrew Morton:
"7 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
proc: add Alexey to MAINTAINERS
kasan: depend on CONFIG_SLUB_DEBUG
include/linux/dax.h: dax_iomap_fault() returns vm_fault_t
x86/e820: put !E820_TYPE_RAM regions into memblock.reserved
slub: fix failure when we delete and create a slab cache
Revert mm/vmstat.c: fix vmstat_update() preemption BUG
lib/percpu_ida.c: don't do alloc from per-CPU list if there is none
KASAN depends on having access to some of the accounting that SLUB_DEBUG
does; without it, there are immediate crashes [1]. So, the natural
thing to do is to make KASAN select SLUB_DEBUG.
[1] http://lkml.kernel.org/r/CAHmME9rtoPwxUSnktxzKso14iuVCWT7BE_-_8PAC=pGw1iJnQg@mail.gmail.com
Link: http://lkml.kernel.org/r/20180622154623.25388-1-Jason@zx2c4.com
Fixes: f9e13c0a5a ("slab, slub: skip unnecessary kasan_cache_shutdown()")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 1c8f422059 ("mm: change return type to vm_fault_t") missed a
conversion. It's not a big problem at present because mainline is still
using
typedef int vm_fault_t;
Fixes: 1c8f422059 ("mm: change return type to vm_fault_t")
Link: http://lkml.kernel.org/r/20180620172046.GA27894@jordon-HP-15-Notebook-PC
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a kernel panic that is triggered when reading /proc/kpageflags
on the kernel booted with kernel parameter 'memmap=nn[KMG]!ss[KMG]':
BUG: unable to handle kernel paging request at fffffffffffffffe
PGD 9b20e067 P4D 9b20e067 PUD 9b210067 PMD 0
Oops: 0000 [#1] SMP PTI
CPU: 2 PID: 1728 Comm: page-types Not tainted 4.17.0-rc6-mm1-v4.17-rc6-180605-0816-00236-g2dfb086ef02c+ #160
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.fc28 04/01/2014
RIP: 0010:stable_page_flags+0x27/0x3c0
Code: 00 00 00 0f 1f 44 00 00 48 85 ff 0f 84 a0 03 00 00 41 54 55 49 89 fc 53 48 8b 57 08 48 8b 2f 48 8d 42 ff 83 e2 01 48 0f 44 c7 <48> 8b 00 f6 c4 01 0f 84 10 03 00 00 31 db 49 8b 54 24 08 4c 89 e7
RSP: 0018:ffffbbd44111fde0 EFLAGS: 00010202
RAX: fffffffffffffffe RBX: 00007fffffffeff9 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000202 RDI: ffffed1182fff5c0
RBP: ffffffffffffffff R08: 0000000000000001 R09: 0000000000000001
R10: ffffbbd44111fed8 R11: 0000000000000000 R12: ffffed1182fff5c0
R13: 00000000000bffd7 R14: 0000000002fff5c0 R15: ffffbbd44111ff10
FS: 00007efc4335a500(0000) GS:ffff93a5bfc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: fffffffffffffffe CR3: 00000000b2a58000 CR4: 00000000001406e0
Call Trace:
kpageflags_read+0xc7/0x120
proc_reg_read+0x3c/0x60
__vfs_read+0x36/0x170
vfs_read+0x89/0x130
ksys_pread64+0x71/0x90
do_syscall_64+0x5b/0x160
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7efc42e75e23
Code: 09 00 ba 9f 01 00 00 e8 ab 81 f4 ff 66 2e 0f 1f 84 00 00 00 00 00 90 83 3d 29 0a 2d 00 00 75 13 49 89 ca b8 11 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 34 c3 48 83 ec 08 e8 db d3 01 00 48 89 04 24
According to kernel bisection, this problem became visible due to commit
f7f99100d8 ("mm: stop zeroing memory during allocation in vmemmap")
which changes how struct pages are initialized.
Memblock layout affects the pfn ranges covered by node/zone. Consider
that we have a VM with 2 NUMA nodes and each node has 4GB memory, and
the default (no memmap= given) memblock layout is like below:
MEMBLOCK configuration:
memory size = 0x00000001fff75c00 reserved size = 0x000000000300c000
memory.cnt = 0x4
memory[0x0] [0x0000000000001000-0x000000000009efff], 0x000000000009e000 bytes on node 0 flags: 0x0
memory[0x1] [0x0000000000100000-0x00000000bffd6fff], 0x00000000bfed7000 bytes on node 0 flags: 0x0
memory[0x2] [0x0000000100000000-0x000000013fffffff], 0x0000000040000000 bytes on node 0 flags: 0x0
memory[0x3] [0x0000000140000000-0x000000023fffffff], 0x0000000100000000 bytes on node 1 flags: 0x0
...
If you give memmap=1G!4G (so it just covers memory[0x2]),
the range [0x100000000-0x13fffffff] is gone:
MEMBLOCK configuration:
memory size = 0x00000001bff75c00 reserved size = 0x000000000300c000
memory.cnt = 0x3
memory[0x0] [0x0000000000001000-0x000000000009efff], 0x000000000009e000 bytes on node 0 flags: 0x0
memory[0x1] [0x0000000000100000-0x00000000bffd6fff], 0x00000000bfed7000 bytes on node 0 flags: 0x0
memory[0x2] [0x0000000140000000-0x000000023fffffff], 0x0000000100000000 bytes on node 1 flags: 0x0
...
This causes shrinking node 0's pfn range because it is calculated by the
address range of memblock.memory. So some of struct pages in the gap
range are left uninitialized.
We have a function zero_resv_unavail() which does zeroing the struct pages
within the reserved unavailable range (i.e. memblock.memory &&
!memblock.reserved). This patch utilizes it to cover all unavailable
ranges by putting them into memblock.reserved.
Link: http://lkml.kernel.org/r/20180615072947.GB23273@hori1.linux.bs1.fc.nec.co.jp
Fixes: f7f99100d8 ("mm: stop zeroing memory during allocation in vmemmap")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Tested-by: Oscar Salvador <osalvador@suse.de>
Tested-by: "Herton R. Krzesinski" <herton@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Cc: Steven Sistare <steven.sistare@oracle.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In kernel 4.17 I removed some code from dm-bufio that did slab cache
merging (commit 21bb13276768: "dm bufio: remove code that merges slab
caches") - both slab and slub support merging caches with identical
attributes, so dm-bufio now just calls kmem_cache_create and relies on
implicit merging.
This uncovered a bug in the slub subsystem - if we delete a cache and
immediatelly create another cache with the same attributes, it fails
because of duplicate filename in /sys/kernel/slab/. The slub subsystem
offloads freeing the cache to a workqueue - and if we create the new
cache before the workqueue runs, it complains because of duplicate
filename in sysfs.
This patch fixes the bug by moving the call of kobject_del from
sysfs_slab_remove_workfn to shutdown_cache. kobject_del must be called
while we hold slab_mutex - so that the sysfs entry is deleted before a
cache with the same attributes could be created.
Running device-mapper-test-suite with:
dmtest run --suite thin-provisioning -n /commit_failure_causes_fallback/
triggered:
Buffer I/O error on dev dm-0, logical block 1572848, async page read
device-mapper: thin: 253:1: metadata operation 'dm_pool_alloc_data_block' failed: error = -5
device-mapper: thin: 253:1: aborting current metadata transaction
sysfs: cannot create duplicate filename '/kernel/slab/:a-0000144'
CPU: 2 PID: 1037 Comm: kworker/u48:1 Not tainted 4.17.0.snitm+ #25
Hardware name: Supermicro SYS-1029P-WTR/X11DDW-L, BIOS 2.0a 12/06/2017
Workqueue: dm-thin do_worker [dm_thin_pool]
Call Trace:
dump_stack+0x5a/0x73
sysfs_warn_dup+0x58/0x70
sysfs_create_dir_ns+0x77/0x80
kobject_add_internal+0xba/0x2e0
kobject_init_and_add+0x70/0xb0
sysfs_slab_add+0xb1/0x250
__kmem_cache_create+0x116/0x150
create_cache+0xd9/0x1f0
kmem_cache_create_usercopy+0x1c1/0x250
kmem_cache_create+0x18/0x20
dm_bufio_client_create+0x1ae/0x410 [dm_bufio]
dm_block_manager_create+0x5e/0x90 [dm_persistent_data]
__create_persistent_data_objects+0x38/0x940 [dm_thin_pool]
dm_pool_abort_metadata+0x64/0x90 [dm_thin_pool]
metadata_operation_failed+0x59/0x100 [dm_thin_pool]
alloc_data_block.isra.53+0x86/0x180 [dm_thin_pool]
process_cell+0x2a3/0x550 [dm_thin_pool]
do_worker+0x28d/0x8f0 [dm_thin_pool]
process_one_work+0x171/0x370
worker_thread+0x49/0x3f0
kthread+0xf8/0x130
ret_from_fork+0x35/0x40
kobject_add_internal failed for :a-0000144 with -EEXIST, don't try to register things with the same name in the same directory.
kmem_cache_create(dm_bufio_buffer-16) failed with error -17
Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1806151817130.6333@file01.intranet.prod.int.rdu2.redhat.com
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit c7f26ccfb2 ("mm/vmstat.c: fix vmstat_update() preemption
BUG"). Steven saw a "using smp_processor_id() in preemptible" message
and added a preempt_disable() section around it to keep it quiet. This
is not the right thing to do it does not fix the real problem.
vmstat_update() is invoked by a kworker on a specific CPU. This worker
it bound to this CPU. The name of the worker was "kworker/1:1" so it
should have been a worker which was bound to CPU1. A worker which can
run on any CPU would have a `u' before the first digit.
smp_processor_id() can be used in a preempt-enabled region as long as
the task is bound to a single CPU which is the case here. If it could
run on an arbitrary CPU then this is the problem we have an should seek
to resolve.
Not only this smp_processor_id() must not be migrated to another CPU but
also refresh_cpu_vm_stats() which might access wrong per-CPU variables.
Not to mention that other code relies on the fact that such a worker
runs on one specific CPU only.
Therefore revert that commit and we should look instead what broke the
affinity mask of the kworker.
Link: http://lkml.kernel.org/r/20180504104451.20278-1-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Steven J. Hill <steven.hill@cavium.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 804209d8a0 ("lib/percpu_ida.c: use _irqsave() instead of
local_irq_save() + spin_lock") I inlined alloc_local_tag() and mixed up
the >= check from percpu_ida_alloc() with the one in alloc_local_tag().
Don't alloc from per-CPU freelist if ->nr_free is zero.
Link: http://lkml.kernel.org/r/20180613075830.c3zeva52fuj6fxxv@linutronix.de
Fixes: 804209d8a0 ("lib/percpu_ida.c: use _irqsave() instead of local_irq_save() + spin_lock")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reported-by: David Disseldorp <ddiss@suse.de>
Tested-by: David Disseldorp <ddiss@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Shaohua Li <shli@fb.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The poll() changes were not well thought out, and completely
unexplained. They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.
Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead. That gets rid of one of the new indirections.
But that doesn't fix the new complexity that is completely unwarranted
for the regular case. The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.
[ This revert is a revert of about 30 different commits, not reverted
individually because that would just be unnecessarily messy - Linus ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These properties are required for compatibility with runtime PM.
Without these properties, MMC host controller will not be aware
of power capabilities. When the wlcore driver attempts to power
on the device, it will erroneously fail with -EACCES. This fixes
a regression found here: https://lkml.org/lkml/2018/6/12/930
Fixes: 60f36637bb ("wlcore: sdio: allow pm to handle sdio power")
Signed-off-by: Ryan Grachek <ryan@edited.us>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
These properties are required for compatibility with runtime PM.
Without these properties, MMC host controller will not be aware
of power capabilities. When the wlcore driver attempts to power
on the device, it will erroneously fail with -EACCES.
Fixes: 60f36637bb ("wlcore: sdio: allow pm to handle sdio power")
Signed-off-by: Ryan Grachek <ryan@edited.us>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This patch avoids that removing a path controlled by the dm-mpath driver
while mkfs is running triggers the following kernel bug:
kernel BUG at block/blk-core.c:3347!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 20 PID: 24369 Comm: mkfs.ext4 Not tainted 4.18.0-rc1-dbg+ #2
RIP: 0010:blk_end_request_all+0x68/0x70
Call Trace:
<IRQ>
dm_softirq_done+0x326/0x3d0 [dm_mod]
blk_done_softirq+0x19b/0x1e0
__do_softirq+0x128/0x60d
irq_exit+0x100/0x110
smp_call_function_single_interrupt+0x90/0x330
call_function_single_interrupt+0xf/0x20
</IRQ>
Fixes: f9d03f96b9 ("block: improve handling of the magic discard payload")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Marek Szyprowski