These definitions are united into the header.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an ethernet driver for the LPC32xx ARM SoC.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
FCoE statistics ids were distinguished from the L2's statistics ids.
However, not all of the change was committed. This causes a possible
collision of indices when FCoE is present.
This patch fixes the issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCB flags were updated using the flags' bit offsets instead of
the actual bits. This is now fixed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed endianess issue when passing arguments to FW.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When pfc statistics were counted, the delta change from last count
was summed twice. This fixes the issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver defaults to 1M MTT segments, where each segment holds
8 MTT entries. This limits the total memory registered to 8M * PAGE_SIZE
which is 32GB with 4K pages. Since systems that have much more memory
are pretty common now (at least among systems with InfiniBand hardware),
this limit ends up getting hit in practice quite a bit.
Handle this by having the driver allocate at least enough MTT entries to
cover 2 * totalram pages.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the MTU for IB ports in the driver instead of using the firmware
default of 2KB (the driver defaults to 4KB). Allow for dynamic mtu
configuration through a new, per-port sysfs entry.
Since there's a dependency between the port MTU and the max number of
HW VLs the port can support, apply a mim/max approach, using a loop
that goes down from the highest possible number of VLs to the lowest,
using the firmware return status to know whether the requested number
of VLs is possible with a given MTU.
For now, as with the dynamic link type change / VPI support, the sysfs
entry to change the mtu is exposed only when NOT running in SR-IOV
mode. To allow changing the MTU for the master in SR-IOV mode,
primary-function-initiated FLR (Function Level Reset) needs to be
implemented.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Print an error message when a thermal error async event is reported by the HW.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Dotan Barak <dotanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 22c8bff6fa ("mlx4_core: Exported functions can't be static")
fixed most of this up, but forgot about mlx4_is_slave_active(). Fix
this one too.
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch has been tested on a machine with the Realtek
RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05).
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not need this leftover of the ISA drivers era.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
This driver is specific to the PowerPC legcay iSeries platform which is
being removed.
Cc: David Miller <davem@davemloft.net>
Cc: <netdev@vger.kernel.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Supports EG20T ptp clock in the driver
Changes e-mail address.
Adds number.
Signed-off-by: Takahiro Shimizu <tshimizu818@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
zero mac address is a valid address for VIC dynamic vnic and sriov Vf's.
Fix the check in enic_set_vf_mac appropriately
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The actual FW command is called in procedure "handle_resize".
Code incorrectly invoked the FW command again (in good flow), in
the modify_cq wrapper function.
Fix by skipping second FW invocation unconditionally for resize.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
ATL1C_WORK_EVENT_RESET is zero so the original code here is a nop. The
intent was to set the zero bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 239c562c94 (ehea: Add 64bit statistics) added a regression,
since we no longer report multicast & rx_errors fields, taken from
port->stats structure. These fields are updated in ehea_update_stats()
every second.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing the work for commit a6f7feae6d ("IB/mlx4: pass SMP
vendor-specific attribute MADs to firmware") we realized that the
firmware would respond on all sorts of vendor-specific MADs.
Therefore commit 97285b7817 ("mlx4_core: Add extended port
capabilities support") adds redundant code into the driver, since
there's no real reaon to maintain the extended capabilities of the
port, as they can be queried on demand (e.g the FDR10 capability).
This patch reverts commit 97285b7817 and removes the check for
extended caps from the mlx4_ib driver port query flow.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch includes:
Configure EMAC PHY clock source (clock from PHY or internal clock).
Do not advertise PHY half duplex capability as APM821XX EMAC does not support half duplex mode.
Add changes to support configuring jumbo frame for APM821XX EMAC.
[ Fix coding style -DaveM ]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device ids for Chelsio's T480-CR and T440-LP-CR
adapters.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device ids for Chelsio's T480-CR and T440-LP-CR
adapters.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing sparse warnings, the 2 functions are only used in same
file. Defining them as static and not exporting them.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing functions that are no longer in use, but still exist
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SET_PORT functions are implemented in port.c, which is part
of mlx4_core, these functions are exported. The functions are in use by
the mlx4_en module (were originally part of mlx4_en).
Their declaration remained in mlx4_en module, moving the declaration to the right location.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac should be written as __be64 the gid. The warning was because
we changed the mac parameter, which is u64, by writing result of cpu_to_be64
into it. Fixing by using new variable of type __be64.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The keys used for the hardware RSS topelitz hash are of type __be32
where the values provided by the driver are from array of u32,
this triggered sparse warning on incorrect type in assignment as of different base types.
Since these values are picked randomly,
the fix is to transform the key to __be32 by executing cpu_to_be_32()
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blue flame buffer is defined to be of type void __iomem *
but was passed to mlx4_bf_copy which gets unsigned long * .
This triggered sparse warning on different address spaces,
fix that by changing mlx4_bf_copy first param to be of type void __iomem * .
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings on incompatibility between the endianess of the ctrl_flags
field of struct mlx4_en_priv to the srcrb_flags field of struct
mlx4_wqe_ctrl_seg by changing the former to be __be32 instead of u32.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Localized the pdev->dev, and using dma_map instead of pci_map
There are multiple map/unmap operations on data path,
optimizing those by saving redundant pointer access.
Those places were identified as hot-spots when running kernel profiling
during some benchmarks.
The fixes had most impact when testing packet rate with small packets,
reducing several % from CPU load, and in some case being the difference
between reaching wire speed or being CPU bound.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Silence the following warning:
"warn: returning -1 instead of -ENOMEM is sloppy".
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a bug introduced by commit fe9a2603c, where the priority bits
in the schedule queue field were masked out.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
With runtime PM, if the ethernet cable is disconnected, the device is
transitioned to D3 state to conserve energy. If the system is shutdown
in this state, any register accesses in rtl_shutdown are dropped on
the floor. As the device was programmed by .runtime_suspend() to wake
on link changes, it is thus brought back up as soon as the link recovers.
Resuming every suspended device through the driver core would slow things
down and it is not clear how many devices really need it now.
Original report and D0 transition patch by Sameer Nanda. Patch has been
changed to comply with advices by Rafael J. Wysocki and the PM folks.
Reported-by: Sameer Nanda <snanda@chromium.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe of each port, read and log the part number from VPD.
Remove the Falcon-specific board name lookup.
Initial version by Stuart Hodgson <smhodgson@solarflare.com>.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Generate a test event on each event queue whenever the interface is
brought up, then after 1 second check that we have either handled a
test event or handled another IRQ for each event queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
In case all event queues are broken for some reason, this means it
will only take about a second to check them all, rather than up to 32
seconds. This may also speed up testing in the successful case.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
IRQ latency can be ridiculously high for various reasons, so our
current timeouts of 100 ms or 10 ms are too short.
Change the IRQ and event tests to use polling loops starting with a
delay of 1 tick and doubling that if necessary up to a maximum total
delay of approximately 1 second.
Raise the loopback packet RX timeout to 1 second.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
RX and TX completions on the same event queue are generally not associated
with the same flows. The inclusion of TX completions in the adaptive IRQ
score is more of a source of noise rather than useful feedback. Therefore,
do not include them in the score, and adjust the default threshold scores
down.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The in-tree driver has never supported Driverlink. The rest of the
comments are rather redundant, but we can usefully state what the
requirements are on the buffer state.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Fix tg3 to use BQL multi queue related netdev interfaces since the
device supports multi queue.
Signed-off-by: Tom Herbert <therbert@google.com>
Reported-by: Christoph Lameter <cl@gentwo.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to use ndo_get_stats64 to get 64bit statistics.
Two sync entries are used (one for Rx and one for Tx).
Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vmxnet3/vmxnet3_drv.c
Small vmxnet3 conflict with header size bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing fancy:
- sent bytes count is notified in the start_xmit path right before
updating the owner bit in the hardware Tx descriptor (E. Dumazet)
- avoid useless tp->dev dereferencing in start_xmit (E. Dumazet)
Use of netdev_reset_queue is favored over proper accounting in
rtl8169_tx_clear_range since the latter would need more work for the
same result (nb: said accounting degenerates to nothing in xmit_frags).
Signed-off-by: Igor Maravic <igorm@etf.rs>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Switch to use ndo_get_stats64 to get 64bit statistics.
Two sync entries are used (one for Rx and one for Tx).
Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
In 'ql_adapter_initialize'
the first call for 'spin_unlock_irqrestore()' is with hw_flags = 0,
which is as good as 'spin_unlock_irq()' (unconditional interrupt
enabling). If this is intended, then for better performance
'spin_unlock_irqrestore()' can be replaced with 'spin_unlock_irq()'
and 'spin_lock_irqsave()' can be replaced by 'spin_lock_irq()
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix new sparse errors introduced in commit 6221217199 (mlx4_en: dont
change mac_header on xmit)
Reported-by: Or Gerlitz <or.gerlitz@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch recodes the MRRS cap for 5719 A0 devices as a PCI quirk.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the the existing allocation and free operations
so that they can be used individually.
This is to improve code readability, and also to prepare for
possible future changes like better error recovery and more
dynamic configuration (e.g on-the-fly resizing of the rings).
This change represents a straight up relocation of the existing
code into separate routines without changing any of the contained
code itself. Local variables are relocated as necessary.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRC reset causes the read DMA engine to go into a mode that breaks up
requests into 256 bytes. A PHY reset is required to bring it back to
the normal mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for weak memory model architectures to ensure that the chip will DMA
valid BD data.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback on 9K packet fails because the chip has a DMA limit of 4K. The
loopback test logic uses a single BD for simplicity. Fix it by reducing
the jumbo packet size to the DMA limit.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
{g|s}etnumtcs() today returns a u8 that is only used by the DCB code
to verify no error occurred. Today the driver implementations return
negative error codes which end up being non-zero so the logic works
out but triggers some sparse warnings.
To fix the sparse warnings convert the return value to an int.
CC: Eilon Greenstein <eilong@broadcom.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
dcb netlink code calls setup_tc to init hardware traffic classes
to use for DCB. At some call sites the return values are not
checked for errors and in one case may return -EINVAL back to
the net/dcbnl.c caller which is expecting a u8.
This fixes some smatch hits and although failures are never
seen in practive its best to check return codes.
Reported-by: Dan Carenter <dan.carpenter@oracle.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The old code would += the total errors every time
stats were gathered. Instead, keep a count of short-pkt
and long-pkt counters and then simply add them together
for the rx-over-length stat.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Noticed with the 8168d (-vb-gr, aka RTL_GIGA_MAC_VER_26).
ConfigX registers should only be written while the Config9346 lock
is held.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the big network driver reorg, each vendor directory defaults to
yes, so that older config's can migrate correctly. Looks like this one
got missed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/tg3.c
Conflicts in the statistics regression bug fix from 'net',
but happily Matt Carlson originally posted the fix against
'net-next' so I used that to resolve this.
Signed-off-by: David S. Miller <davem@davemloft.net>
"num_vfs" is a u32 but we only use the high 16 bits and the low 16bits
are left as zero. That isn't a problem for little endian systems but it
will break on big endian ones.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pch_gbe_validate_option() modifies 32 bits of memory but we pass
&hw->phy.autoneg_advertised which only has 16 bits and &hw->mac.fc
which only has 8 bits.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects several comments that are either incorrect or formatted
incorrectly for multiline comments.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct spelling error caught with codespell.py.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to address several minor issues in
ixgbe_xmit_frame_ring. Specifically it adds a comment explaining the TXSW
flag, and correctly wraps a line over 80 characters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000_link_stall_workaround_lv() function is always called in non-
atomic context so it should use msleep instead of mdelay. Also, remove
unnecessary #include <linux/delay.h>.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows the NIC to receive packets with bad FCS
and other errors. Good for sniffing packets on flakey
networks.
v4: Only flax rx-over-length errors if pkt is beyond
maximum expected packet size, not just beyond the MTU.
This matches the existing logic for this counter.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This can aid with testing the RX logic for bad
CRCs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows e100 to be configured to append the
Ethernet FCS to the skb.
Useful for sniffing networks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
tg3_get_stats64() takes tp->lock when dealing with non-serdes bcm5700
and bcm5701 devices. However, functions that call tg3_halt() have
already acquired tp->lock. When tg3_get_stats64() is called in
tg3_halt(), deadlock will occur.
This patch fixes the problem by separating the stat gathering code into
a new tg3_get_nstats() function. tg3_get_stats64() is recoded to call
this function and take tp->lock. The code that takes tp->lock in
tg3_calc_crc_errors() has been removed. Function signatures have been
cleaned up too.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to use the new 'saddr' variable not the void 'addr' in
set_mac_address().
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'imx/driver' of git://git.linaro.org/people/shawnguo/linux-2.6: (3 commits)
ARM: imx6q: add cko1 clock
ARM: mxc: make imx_dma_is_general_purpose more generic for sdma
ARM: imx6: Rename DEBUG_IMX6Q_UART to UART4
* 'features/cs89x0' of git://git.pengutronix.de/git/imx/linux-2.6:
CS89x0 : add CS89x0 platform device to the iMX31ADS board
CS89x0 : remove QQ2440 board support from the CS89x0 driver
CS89x0 : add CS89x0 platform device to the iMX21ADS board
CS89x0 : add platform driver support
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) ICMP sockets leave err uninitialized but we try to return it for the
unsupported MSG_OOB case, reported by Dave Jones.
2) Add new Zaurus device ID entries, from Dave Jones.
3) Pointer calculation in hso driver memset is wrong, from Dan
Carpenter.
4) ks8851_probe() checks unsigned value as negative, fix also from Dan
Carpenter.
5) Fix crashes in atl1c driver due to TX queue handling, from Eric
Dumazet. I anticipate some TX side locking fixes coming in the near
future for this driver as well.
6) The inline directive fix in Bluetooth which was breaking the build
only with very new versions of GCC, from Johan Hedberg.
7) Fix crashes in the ATP CLIP code due to ARP cleanups this merge
window, reported by Meelis Roos and fixed by Eric Dumazet.
8) JME driver doesn't flush RX FIFO correctly, from Guo-Fu Tseng.
9) Some ip6_route_output() callers test the return value for NULL, but
this never happens as the convention is to return a dst entry with
dst->error set. Fixes from RonQing Li.
10) Logitech Harmony 900 should be handled by zaurus driver not
cdc_ether, update white lists and black lists accordingly. From
Scott Talbert.
11) Receiving from certain kinds of devices there won't be a MAC header,
so there is no MAC header to fixup in the IPSEC code, and if we try
to do it we'll crash. Fix from Eric Dumazet.
12) Port type array indexing off-by-one in mlx4 driver, fix from Yevgeny
Petrilin.
13) Fix regression in link-down handling in davinci_emac which causes
all RX descriptors to be freed up and therefore RX to wedge
completely, from Christian Riesch.
14) It took two attempts, but ctnetlink soft lockups seem to be
cured now, from Pablo Neira Ayuso.
15) Endianness bug fix in ENIC driver, from Santosh Nayak.
16) The long ago conversion of the PPP fragmentation code over to
abstracted SKB list handling wasn't perfect, once we get an
out of sequence SKB we don't flush the rest of them like we
should. From Ben McKeegan.
17) Fix regression of ->ip_summed initialization in sfc driver.
From Ben Hutchings.
18) Bluetooth timeout mistakenly using msecs instead of jiffies,
from Andrzej Kaczmarek.
19) Using _sync variant of work cancellation results in deadlocks,
use the non _sync variants instead. From Andre Guedes.
20) Bluetooth rfcomm code had reference counting problems leading
to crashes, fix from Octavian Purdila.
21) The conversion of netem over to classful qdisc handling added
two bugs to netem_dequeue(), fixes from Eric Dumazet.
22) Missing pci_iounmap() in ATM Solos driver. Fix from Julia Lawall.
23) b44_pci_exit() should not have __exit tag since it's invoked from
non-__exit code. From Nikola Pajkovsky.
24) The conversion of the neighbour hash tables over to RCU added a
race, fixed here by adding the necessary reread of tbl->nht, fix
from Michel Machado.
25) When we added VF (virtual function) attributes for network device
dumps, this potentially bloats up the size of the dump of one
network device such that the dump size is too large for the buffer
allocated by properly written netlink applications.
In particular, if you add 255 VFs to a network device, parts of
GLIBC stop working.
To fix this, we add an attribute that is used to turn on these
extended portions of the network device dump. Sophisticaed
applications like 'ip' that want to see this stuff will be changed
to set the attribute, whereas things like GLIBC that don't care
about VFs simply will not, and therefore won't be busted by the
mere presence of VFs on a network device.
Thanks to the tireless work of Greg Rose on this fix.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
sfc: Fix assignment of ip_summed for pre-allocated skbs
ppp: fix 'ppp_mp_reconstruct bad seq' errors
enic: Fix endianness bug.
gre: fix spelling in comments
netfilter: ctnetlink: fix soft lockup when netlink adds new entries (v2)
Revert "netfilter: ctnetlink: fix soft lockup when netlink adds new entries"
davinci_emac: Do not free all rx dma descriptors during init
mlx4_core: Fixing array indexes when setting port types
phy: IC+101G and PHY_HAS_INTERRUPT flag
netdev/phy/icplus: Correct broken phy_init code
ipsec: be careful of non existing mac headers
Move Logitech Harmony 900 from cdc_ether to zaurus
hso: memsetting wrong data in hso_get_count()
netfilter: ip6_route_output() never returns NULL.
ethernet/broadcom: ip6_route_output() never returns NULL.
ipv6: ip6_route_output() never returns NULL.
jme: Fix FIFO flush issue
atm: clip: remove clip_tbl
ipv4: ping: Fix recvmsg MSG_OOB error handling.
rtnetlink: Fix problem with buffer allocation
...
A driver xmit function is not allowed to change skb without special
care.
mlx4_en_xmit() should not call skb_reset_mac_header() and instead should
use skb->data to access ethernet header.
This removes a dumb test : if (ethh && ethh->h_dest)
Also remove this slow mlx4_en_mac_to_u64() call, we can use
get_unaligned() to get faster code.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
ConnectX devices have a limit on the number of mappings that can be
done on an FMR before having to call sync_tpt. The current
mlx4_ib driver reports the limit correctly in max_map_per_fmr in
.query_device(), but mlx4_core doesn't check it when actually
allocating FMRs.
Add a max_fmr_maps field to struct mlx4_caps and enforce this maximum
value on FMR allocations.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Rename e1000e_reload_nvm() to e1000e_reload_nvm_generic() to signify the
function is used for more than one MAC-family type, and set and use it as a
MAC ops function pointer to be consistent with the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove reference to non-existant function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename e1000e_config_collision_dist() to
e1000e_config_collision_dist_generic() to signify the function is used for
more than one MAC-family type, and set and use it as a MAC ops function
pointer to be consistent with the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call the MAC ops setup_physical_interface function pointer instead of the
MAC-family-specific function to conform to the rest of the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace e1000_check_reset_block() inline function with calls to the PHY ops
check_reset_block function pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace e1000_check_mng_mode() inline function with calls to the MAC ops
check_mng_mode function pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename e1000e_setup_link() to e1000e_setup_link_generic() to signify the
function is used for more than one MAC-family type. The 82571-family has
a custom setup_link function which also calls the generic function. The
ich8lan-family has a custom function which should just be called via the
function pointer. The 80003es2lan-family just uses the generic function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename e1000e_id_led_init() to e1000e_id_led_init_generic() to signify the
function is used for more than one MAC-family type. For the ich8lan MAC
family, some MACs use the generic function and others use the function
e1000_id_led_init_pchlan(). In all cases where e1000e_id_led_init() was
called directly, change to call the function pointer to be consistent with
the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When pre-allocating skbs for received packets, we set ip_summed =
CHECKSUM_UNNCESSARY. We used to change it back to CHECKSUM_NONE when
the received packet had an incorrect checksum or unhandled protocol.
Commit bc8acf2c8c ('drivers/net: avoid
some skb->ip_summed initializations') mistakenly replaced the latter
assignment with a DEBUG-only assertion that ip_summed ==
CHECKSUM_NONE. This assertion is always false, but it seems no-one
has exercised this code path in a DEBUG build.
Fix this by moving our assignment of CHECKSUM_UNNECESSARY into
efx_rx_packet_gro().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Acked-by: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print MAC/dev_addr via printk extended format specifier %pM instead
of custom code.
Use memcpy to set the address to dev->dev_addr in set_mac_address,
instead of mxing it up in a for loop with printing a debug msg.
Check also if the given address is valid.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print MAC/dev_addr via printk extended format specifier %pM
instead of custom code.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pr_<level> for printk
Use temporary instead of multiple pr_conts
Coalesce formats.
Save a few bytes of object code too:
$ size drivers/net/ethernet/intel/e1000/e1000_main.o*
text data bss dec hex filename
60507 369 14120 74996 124f4
drivers/net/ethernet/intel/e1000/e1000_main.o.new
60717 369 14176 75262 125fe
drivers/net/ethernet/intel/e1000/e1000_main.o.old
Removed printing of pktdata.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Separate a complicated bit of e1000_config_dsp_after_link_change
into a new static function e1000_1000Mb_check_cable_length.
Reduces indentation and adds a bit of clarity.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent discussions on LKML, kernel-janitors, linux-wireless and netdev
have suggested boolean comparisons should use logical operators instead of
equality comparisons with true/false.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows the NIC to receive the Ethernet FCS
and pass it up the stack, allowing sniffers and
other interested programs to inspect the FCS.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to receive packets with bad FCS and
Runts, which can help when sniffing.
NOTE: r8169, at least on my NIC, silently drops packets
with bad FCS instead of counting them. It seems they are
only received in any fashion if the RxCRC flag is set
(which this patch allows).
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to pass the Ethernet FCS on up
the stack, and is useful when sniffing networks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to receive Runts and frames with bad
Ethernet Frame Checksums (FCS).
Useful to sniffing & diagnosing bad networks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This allows the NIC to pass the Ethernet Frame Checksum
(FCS) up the stack. Useful when sniffing packets.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Good for testing the RX logic for bad CRC handling.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows the NIC to receive all frames available, including
those with bad FCS, un-matched vlans, ethernet control frames,
and more.
Tested by sending frames with bad FCS.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This can aid with testing the RX logic for bad
CRCs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This enables enabling/disabling reception of the Ethernet
FCS. This can be useful when sniffing packets.
For e1000e, enabling RXFCS can change the default
behaviour for how the NIC handles CRC. Disabling RXFCS
will take the NIC back to defaults, which can be configured
as part of the module options.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a regression that was introduced by
commit 0a5f384677
davinci_emac: Add Carrier Link OK check in Davinci RX Handler
Said commit adds a check whether the carrier link is ok. If the link is
not ok, the skb is freed and no new dma descriptor added to the rx dma
channel. This causes trouble during initialization when the carrier
status has not yet been updated. If a lot of packets are received while
netif_carrier_ok returns false, all dma descriptors are freed and the
rx dma transfer is stopped.
The bug occurs when the board is connected to a network with lots of
traffic and the ifconfig down/up is done, e.g., when reconfiguring
the interface with DHCP.
The bug can be reproduced by flood pinging the davinci board while doing
ifconfig eth0 down
ifconfig eth0 up
on the board.
After that, the rx path stops working and the overrun value reported
by ifconfig is counting up.
This patch reverts commit 0a5f384677
and instead issues warnings only if cpdma_chan_submit returns -ENOMEM.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Cc: Hegde, Vinay <vinay.hegde@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CLKDIV bitfield in the MDIO Control Register is a 16 bit field,
therefore the CLKDIV value may range from 0 to 0xffff.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
chan->chan_num is 0..CPDMA_MAX_CHANNELS-1 for tx channels and
CPDMA_MAX_CHANNELS..2*CPDMA_MAX_CHANNELS-1 for rx channels. However,
the rx and tx teardown registers expect zero based channel numbering.
Since the upper bits of the registers are reserved, the teardown also
worked before, this patch is cleanup only.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will prevent double free in some cases where be_clear() is called
for cleanup when be_setup() fails half-way.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a part of be_close(), instead of waiting for a max of 200ms for each TXQ,
wait for a total of 200ms for completions from all TXQs to arrive.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH recovery involves ring cleanup and re-creation. The worker
thread must not run during EEH cleanup/resume.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on powerpc, it breaks the build if exported functions are
static. Fix some static exported functions introduced with the mlx4
SR-IOV support added in 3.3-rc1.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch seeks to clean up the timer related code. It begins by
moving one-time timer setup code from tg3_open() to tg3_init_one().
It then creates a function that encapsulates the code needed to start
the timer. A tg3_timer_stop() function was added for parity. Finally,
this patch moves all the timer functions to a more suitable location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error happens in the tx completion thread, tg3_reset_task will be
scheduled and TX_RECOVERY_PENDING will be set. The TX_RECOVERY_PENDING
flag causes tg3_poll[_msix] to return early before doing much of its
work. Tg3_reset_task() gets canceled when the configuration of the
device is changing, which always results in a chip reset. When this
happens, the TX_RECOVERY_PENDING flag may be left set, which would
unnecessarily hinder tg3_poll from doing work. This patch fixes the
problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_phy_copper_begin() has code that configures the link
advertisements through the use of the link_config.speed and
link_config.duplex members. The driver does not internally use these
members in this way, nor is it (currently) permitted via the ethtool
interface. This patch removes the dead code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver tried to detect link changes by comparing the tg3 local
active_speed member with SPEED_UNKNOWN (or formerly SPEED_INVALID).
This check is not correct, since phylib will never set its speed member
to either of these two values. The code only appeared to work because
tg3 initializes active_speed to SPEED_INVALID during tg3_init_one. This
patch introduces a new "old_link" tg3 member and then compares the
phy_device's link member against it to detect link state changes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_for_each_possible_channel_tx_queue() should do nothing for RX-only
or extra channels. The current definition results in allocating
additional unused hardware TX queues when using the mqprio qdisc and
either separate_tx_channels or SR-IOV.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We have a very simple way of allocating buffer table entries to
queues, which is just to take the next one available. The extra
channels are the highest numbered channels but they need to be
allocated the lowest entries so that the traffic channels can be
allocated new entries without any collisions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_vfdi_set_status_page() validates the peer page count by
calculating the size of a request containing that many addresses and
comparing that with the maximum valid request size (4KB). The
calculation involves a multiplication that may overflow on a 32-bit
system.
We use kcalloc() to allocate memory to store the addresses; that also
does a multiplication and it does check for integer overflow, so any
values larger than 0x1fffffff will be rejected. However, values in
the range [0x1fffffffc, 0x1fffffff] pass boh tests and result in an
attempt to allocate nearly 4GB on the heap. This should be rejected
rather quickly as it's obviously impossible on a 32-bit system, and
indeed the maximum possible heap allocation is 32MB. Still, let's
make absolutely sure by fixing the initial validation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This requirement was meant to be implied in the name 'status page'.
One out-of-tree VF driver allocates a buffer using the structure size
and not a full page - hence the current odd specification - but in
practice that allocation will be padded and aligned to at least 4KB.
Therefore, we can specify this and have the option to extend the
structure up to 4KB without worrying about VF drivers using odd-shaped
buffers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
ip6_route_output() never returns NULL, so it is wrong to
check if the return value is NULL.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_mac_addr() for .ndo_set_mac_address, remove
typhoon_set_mac_address() since it do currently the same as
eth_mac_addr(). Additional advantage: eth_mac_addr() already
checks if the given address is valid.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Acked-by: Dave Dillow <dave@thedillows.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the RX FIFO flush watermark lower.
According to Federico and JMicron's reply,
setting it to 16QW would be stable on most platforms.
Otherwise, user might experience packet drop issue.
CC: stable@kernel.org
Reported-by: Federico Quagliata <federico@quagliata.org>
Fixed-by: Federico Quagliata <federico@quagliata.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is the last user of the IRQF_SAMPLE_RANDOM flag for net drivers, and since add_*_randomness
interfaces have now deprecated the flag as a source of external noise, we can remove it.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In port type change flow, need to set the new port types only after
all interfaces have finished the unregister process.
Otherwise, during unregister, one of the interfaces might issue a SET_PORT
command with wrong port types, it can cause bad FW behavior.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under the spinlock we call request_irq(), which allocates memory with GFP_KERNEL,
This causes the following trace when DEBUG_SPINLOCK is enabled, it can cause
the following trace:
BUG: spinlock wrong CPU on CPU#2, ethtool/2595
lock: ffff8801f9cbc2b0, .magic: dead4ead, .owner: ethtool/2595, .owner_cpu: 0
Pid: 2595, comm: ethtool Not tainted 3.0.18 #2
Call Trace:
spin_bug+0xa2/0xf0
do_raw_spin_unlock+0x71/0xa0
_raw_spin_unlock+0xe/0x10
mlx4_assign_eq+0x12b/0x190 [mlx4_core]
mlx4_en_activate_cq+0x252/0x2d0 [mlx4_en]
? mlx4_en_activate_rx_rings+0x227/0x370 [mlx4_en]
mlx4_en_start_port+0x189/0xb90 [mlx4_en]
mlx4_en_set_ringparam+0x29a/0x340 [mlx4_en]
dev_ethtool+0x816/0xb10
? dev_get_by_name_rcu+0xa4/0xe0
dev_ioctl+0x2b5/0x470
handle_mm_fault+0x1cd/0x2d0
sock_do_ioctl+0x5d/0x70
sock_ioctl+0x79/0x2f0
do_vfs_ioctl+0x8c/0x340
sys_ioctl+0xa1/0xb0
system_call_fastpath+0x16/0x1b
Replacing with mutex, which is enough in this case.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch provides workaround for BUG in FW 7.2.16,
which in GRO mode may miscalculate buffer and
place on SGE one frag less than it could.
It may happen only for some MTUs, we mark these MTUs
with gro_check flag during device initialization or
MTU change.
Next FW should include fix for the issue and the
patch could be reverted.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch integrates FW 7.2.16 HSI and implements driver
part of GRO flow.
FW 7.2.16 adds the ability to aggregate packets for GRO
(and not just LRO) and also fixes some bugs.
1. Added new aggregation mode: GRO. In this mode packets are aggregated
such that the original packets can be reconstructed by the OS.
2. 57712 HW bug workaround - initialized all CAM TM registers to 0x32.
3. Adding the FCoE statistics structures to the BNX2X HSI.
4. Wrong configuration of TX HW input buffer size may cause theoretical
performance effect. Performed configuration fix.
5. FCOE - Arrival of packets beyond task IO size can lead to crash.
Fix firmware data-in flow.
6. iSCSI - In rare cases of on-chip termination the graceful termination
timer hangs, and the termination doesn't complete. Firmware fix to MSL
timer tolerance.
7. iSCSI - Chip hangs when target sends FIN out-of-order or with isles
open at the initiator side. Firmware implementation corrected to drop
FIN received out-of-order or with isles still open.
8. iSCSI - Chip hangs when in case of retransmission not aligned to 4-bytes
from the beginning of iSCSI PDU. Firmware implementation corrected
to support arbitrary aligned retransmissions.
9. iSCSI - Arrival of target-initiated NOP-IN during intense ISCSI traffic
might lead to crash. Firmware fix to relevant flow.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BF can be disabled in some cases, the capability field, bf_reg_size is set
to zero in this case. Don't map the BF area in this case, it would cause
failures. In addition, leaving the BF area unmapped
also alerts the ETH driver to not use BF.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes enic_probe to do a fw init devcmd for sriov vfs.
This enables vf driver in the guest to get into adapter init state without
having to explicitly issue an init fw cmd with portprofile info. But a
successful init on the vf will require the port profile information to be
pre-provisioned by the hypervisor via the pf
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the ndo_set_vf_mac netdev op to set the sriov vf mac
in adapter using the new fw devcmd CMD_SET_MAC_ADDR. During port profile
associate the pf driver gets the vf mac using CMD_GET_MAC_ADDR.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new devcmd CMD_SET_MAC_ADDR to set the mac address of an
interface.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
firmware devcmd CMD_MAC_ADDR gets the mac address of a vnic from adapter.
This patch renames it to CMD_GET_MAC_ADDR more appropriately.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt adi ethernet driver to changes in bfin_get_ether_addr()
from arch/blackfin. bfin_get_ether_addr() returns now a state.
Set a random mac address via new eth_hw_addr_random() in case
the return value is not 0.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: change the logic to reduce unneeded checks
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct spelling "platfom" to "platform" in
drivers/net/ethernet/lantiq_etop.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8304859a "bnx2x: add fan failure event handling" made the function
bnx2x_close() non-static unnecessarily. The function is not called from
other sources. Make it static again.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARNING: drivers/net/ethernet/broadcom/built-in.o(.init.text+0x5d): Section mismatch in reference from the function b44_init() to the function .exit.text:b44_pci_exit()
module exits with b44_cleanup()
Signed-off-by: Nikola Pajkovsky <n.pajkovsky@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev->irq is unsigned, so it's never less than zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver attempts to use two TX rings but lacks proper support :
1) IRQ handler only takes care of TX completion on first TX ring
2) the stop/start logic uses the legacy functions (for non multiqueue
drivers)
This means all packets witk skb mark set to 1 are sent through high
queue but are never cleaned and queue eventualy fills and block the
device, triggering the infamous "NETDEV WATCHDOG" message.
Lets use a single TX ring to fix the problem, this driver is not a real
multiqueue one yet.
Minimal fix for stable kernels.
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Tested-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c
Small minor conflict in bnx2x, wherein one commit changed how
statistics were stored in software, and another commit
fixed endianness bugs wrt. reading the values provided by
the chip in memory.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v3: adapt to net-next
v2: use bitops, adapt to eth_hw_addr_random(), add a comment
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow commit db62f684. Convert the driver to use the
module_platform_driver() macro which makes the code a bit smaller and
simpler.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set addr_assign_type correctly to NET_ADDR_RANDOM in case
a random MAC address was generated and assigned to the netdevice.
Fix error handling in atl1c_probe(). If atl1c_read_mac_addr()
couldn't get the hw mac address, and a random mac address get
set return the error code. Don't go to err_eeprom in
atl1c_probe(), use the generated MAC address in this case.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: use bitops
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set addr_assign_type correctly to NET_ADDR_RANDOM in case
a random MAC address was generated and assigned to the netdevice.
Fixed ethoc_set_mac_address() to check if the given mac
address is valid and set also dev_addr of the net_device.
Check also the return value of ethoc_set_mac_address() in
ethoc_probe().
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: set net_device->dev_addr in ethoc_set_mac_address(),
check if given address is valid
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Reset the state of addr_assign_type to NET_ADDR_PERM as soon as
the MAC get changed via .ndo_set_mac_address.
v2: use bitops to reset addr_assign_type
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: reworked to prevent using an extra variable
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
Remove one memcpy from emac_dev_setmac_addr() since this is a
duplicate: it's already done some lines above.
v2: use bitops, adapt to eth_hw_addr_random, remove a memcpy
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set addr_assign_type correctly to NET_ADDR_RANDOM in case
a random MAC address was generated and assigned to the netdevice.
v2: added comment, renamed bool variable to random_mac
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
v2: adapt to eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some controllers have TSU. It can register one VLAN tag, and it can
filter other VLAN tag by hardware.
If vlan_rx_add_vid() is called twice or more, the driver will disable
the filtering.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some controllers have TSU. It can filter multicast by hardware.
This patch supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the controller has TSU, the each channel needs TSU registers.
This patch also fixes the iounmap condition in the sh_eth_drv_remove().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7757 has 2 Fast Ethernet and 2 Gigabit Ethernet, and the first
Gigabit channel needs the initialization. So, this patch adds the
parameter of "needs_init", and if the sh_eth_plat_data is set it
to 1, the driver will initialize the channel.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SH7757's GETHER has TSU registers. So, this patch adds the value
of ".tsu = 1" in the sh_eth_cpu_data.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the SFC9000 family, each port has 1024 Virtual Interfaces (VIs),
each with an RX queue, a TX queue, an event queue and a mailbox
register. These may be assigned to up to 127 SR-IOV virtual functions
per port, with up to 64 VIs per VF.
We allocate an extra channel (IRQ and event queue only) to receive
requests from VF drivers.
There is a per-port limit of 4 concurrent RX queue flushes, and queue
flushes may be initiated by the MC in response to a Function Level
Reset (FLR) of a VF. Therefore, when SR-IOV is in use, we submit all
flush requests via the MC.
The RSS indirection table is shared with VFs, so the number of RX
queues used in the PF is limited to the number of VIs per VF.
This is almost entirely the work of Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Each port has a block of 64-bit SRAM that is divided between buffer
table and descriptor cache regions at initialisation time. Currently
we use a fixed allocation, but it needs to be changed to support
larger numbers of queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This lets us identify the NIC affected in case of failure, and
will be necessary to adjust for SR-IOV constraints.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Abstract some of the channel operations to allow for 'extra'
channels that do not have RX or TX queues.
- Try to assign a channel to each extra channel type that is enabled
for the NIC, but gracefully degrade if we can't allocate sufficient
MSI-X vectors
- Allow each extra channel type to generate its own channel name
- Allow channel types to disable reallocation and reinitialisation
of their channels
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The TX DMA engine issues upstream read requests when there is room in
the TX FIFO for the completion. However, the fetches for the rest of
the packet might be delayed by any back pressure. Since a flush must
wait for an EOP, the entire flush may be delayed by back pressure.
Mitigate this by disabling flow control before the flushes are
started. Since PF and VF flushes run in parallel introduce
fc_disable, a reference count of the number of flushes outstanding.
The same principle could be applied to Falcon, but that
would bring with it its own testing.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
For SR-IOV we will need to send events to event queues that belong to
VFs serviced by other drivers. Change the parameters of
efx_generate_event() to allow this and declare it extern.
While we're at it, remove the existing declaration under the wrong
name efx_nic_generate_event().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
When SR-IOV is enabled we may receive FLR (Function-Level Reset)
events, associated queue flush events and requests from VF drivers at
any time. Therefore we need to keep event queues and interrupts
enabled whenever possible.
Currently we stop interrupt-driven event processing before flushing RX
and TX queues; efx_nic_flush_queues() then polls event queues for
flush events and discards any others it finds. Change it to work with
the regular event handling functions.
Currently efx_start_channel() fills RX queues synchronously when a
device is brought up. This could now race with NAPI, so change it to
send fill events.
This was almost entirely written by Steve Hodgson, formerly
shodgson@solarflare.com.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The RMFT_DEST_MAC and TMFT_SRC_MAC register fields were previously
documented as 44 bits wide, whereas a MAC address has 48 bits.
Thankfully the hardware uses the correct width and the driver has
used separate definitions that divide each of these into 32-bit and
16-bit fields.
Fix the initial definitions for these fields and rewrite the latter
definitions to use them.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Yuval Mintz