This patch factors out converting a memory region type into
a name string, mainly so that it can be used in log commands.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the firmware has any system event signalling controls, signal
them during DSP PRE_PMD to tell the firmware it is about to be stopped.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver fine-tune some parameters to improve FLL performance.
Those items have description as follow.
(1)ICTRL_LATCH: FLL DSP speed capability control
When FLL running at high frequency with long decimal number, DSP needs
to operate at high speed. FLL DSP can optimize between performance and
power consumption by ICTRL_LATCH.(111 has highest power consumption.)
The default setting can be used to reduce power.
(2)CUTOFF500: loop filter cutoff frequency at 500Khz
It will give the best FLL performance but highest power consumption
to enable the cutoff frequency. FLL Loop Filter enable to reduce FLL
output noise, especially,(DCO frequency)/(FLL input reference frequency)
is not a integer.
(3)GAIN_ERR: FLL gain error correction threshold setting
The threshold is comparison between DCO and target frequency.
The value 1111 has the most sensitive threshold, that is, 1111 can have
the most accurate DCO to target frequency. However, the gain error setting
conditionally and inversely depends on FLL input reference clock rate.
Higher FLL reference input frequency can only set lower gain error, such
as 0000 for input reference from MCLK=12.288Mhz. On the other side, if FLL
reference input is from Frame Sync, 48KHz, higher error gain can apply
such as 1111.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Over Sampling Rate (OSR) is defined as CLK_ADC frequency divided by the
audio sample rate (Fs).
OSR = CLK_ADC / FS
The available OSRs are 32, 64, 128 or 256. Note that the OSR and Fs
values must be selected such that the maximum frequency of CLK_ADC
is less than 6.144 MHz. It is recommended to match the relationship
between OSR and clock SRC according to following Table.
ADC_RATE: 00(OSR=32) | CLK_ADC_SRC: 11(CODEC 1/8)
ADC_RATE: 01(OSR=64) | CLK_ADC_SRC: 10(CODEC1/4)
ADC_RATE: 10(OSR=128) | CLK_ADC_SRC: 01(CODEC 1/2)
ADC_RATE: 11(OSR=256) | CLK_ADC_SRC: 00(CODEC CLK)
The over sampling rate about DAC follows the same rule with ADCs.
The driver changes the OSR to 64 value when initiation for better FLL
performance and applies the dynamic SRC change by different OSR.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the short Frame Sync detection logic enabled, the logic will check the
short frame sync threshold. If frame sync is less than the setting;
for example, frame sync less than 252 MCLK, the short frame sync signal is
flagged, digital filter temporary mute and skip that data.
If the system was intended for sampling rate change which could create
temporary short frame sync and not enough MIPS to run the digital filter.
But the situation doesn't happen in ALSA architecure. Thus the Frame Sync
is always stable, then no require to do the detection. Therefore,
the dirver disables the function for better performance.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The compatible table was not updated when the support for DAC3100 was added.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to arizona_init_notifiers was only added for CODECs that are
generating voice trigger events, however, this is somewhat annoying
for machine drivers that might be used with multiple CODECs as they
need to conditionally register for the notifier, depending on the
CODEC being attached.
As the cost of initialising the notifier is so minimal, and we may
well add other events in the future that apply to more CODECs, simply
do this for all Arizona CODECs.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These functions are very thin wrappers around core functions, so they
make sense as inline functions. Also making them inline avoids build
issues in the case where the machine driver is built in but the CODEC
is built as a module.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core expects "const char * const" and "unsigned int" for enum
controls, the mixer control definitions in wm2200 use "const char *"
and "int". This patch corrects the type of these arrays.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/cs42l42.c:1972:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pm8916_wcd_analog_enable_micbias_int1() should set micbias1_cap_mode
rather than micbias2_cap_mode.
Also change the order of pm8916_wcd_analog_enable_micbias_int1/init2
functions for better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using simple-card with the wm8978 doesn't work because simple card calls
set_sysclk on the clock index 0, which is not the MCLK in the WM8978.
Adjust the clock definition so that the clock 0 is the MCLK.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Cirrus Logic CS42L42 codec. SoundWire support
is not enabled. Features support for I2C control and I2S audio.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove
the wrappers.
Also use snd_soc_update_bits() where appropriate.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the stac9766 driver still uses custom snd_soc_codec_driver IO
callbacks. This has been deprecated for a while, so convert the stac9766
driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stac9766 driver has a header file that defines 3 register locations.
Move these to the main source file since it is not really worth it having a
separate file for them. The header file is now empty and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AC'97 standard defines paging support for the register range 0x60-0x6f.
Meaning registers in this window are mapped to different physical registers
depending on the setting of the page select register (0x24).
The stac9766 implements support for switching between page 0 and page 1
depending on the addressed register. But the driver never accesses any
registers from page 1, in addition page 0 is the page selected by default.
Considering the development history it is unlikely that the driver will see
any new features that require paging support. Removing the paging support
makes transitioning the driver to regmap a bit more straight forward.
The default register value table is update to contain the values from page
0, rather than page 1.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used instead and the defines are
unused.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch renames msm8916_wcd_digital_parse_dt() to
msm8916_wcd_digital_get_clks() as the function is not directly dealing
with dt parsing.
No functional changes done.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the code which is not parsing dt from pm8916_wcd_analog_parse_dt()
to make it clear to reader.
No functional changes done.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support double channel shared controls split across 2 registers, one
for each channel, we must be able to update both registers together.
Add a second set of register fields to struct snd_soc_dapm_update, and
update the DAPM control writeback (put) callbacks to support this.
For codecs that use custom events which call into DAPM to do updates,
also clear struct snd_soc_dapm_update before using it, so the second
set of fields remains clean.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/codecs/wm8580.c:988:33: warning:
symbol 'wm8580_data' was not declared. Should it be static?
sound/soc/codecs/wm8580.c:992:33: warning:
symbol 'wm8581_data' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mono ADC Capture Switch control is missing in the driver. So, add it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a DAI specifies "#sound-dai-cells = <0>" in device-tree then
hdmi_of_xlate_dai_name() will be called with zero args, which it isn't
implemented to cope with. The resulting use of an uninitialised variable
for the id will usually result in an error like:
asoc-simple-card sound: parse error -11
asoc-simple-card: probe of sound failed with error -11
Fix this by using and id of zero if no arg is provided.
Fixes: 9731f82d60 ("ASoC: hdmi-codec: enable multi probe for same device")
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
da7219 output (for headset capture) should be set to high-impedance when
not in use, since it will otherwise interfere with output from other
codecs attached to the same DAI.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's difficult to guess from bunch of "ret=-121" errors what driver and
device actually caused them. Since struct i2c_client has the dev pointer
use that for dev_err() with meaningful error message.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4c5d146929 ("ASoC: max98504: Add max98504 speaker amplifier
driver") added new max98504, but this patch didn't add it to
SND_SOC_ALL_CODECS. This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the compressed ops run on the platform side of things we should
really access the driver data through the platform pointer rather than
the CODEC pointer. As the compressed DAIs in our systems always connect
our CODEC to our platform this has never been an issue, but should still
be corrected. Additionally it clears the way for future core refactoring
work.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 31833ead95 ("ASoC: arizona: Move request of speaker IRQs into bus probe")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some registers accesses are done in atomic context.
Enable fast io to use spinlock instead of mutex to protect access.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
stih416 is no more supported, clean associated code.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the DSP compressed data IRQ from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is more idiomatic to request all resources in the bus level probe,
this patch moves the request of the speaker thermal event IRQs from the
ASoC level probe into the bus level probe.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CS35L34_CHIP_ID is not a register address, it's the value read from
CS35L34_DEVID_AB/CD/E registers.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't manually enable cache_bypass for reading the ID registers they
don't have a default anyway so the first read will always hit the
hardware. The old code worked this is simply the more standard way
to implement this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rather than manually enabling cache bypass when reading the ID registers
simply remove the default which will cause the first read to go to the
hardware. The old code worked this is simply the more standard way to
implement this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rather than manually enabling cache bypass when reading the ID registers
simply remove the default which will cause the first read to go to the
hardware. The old code worked this is simply the more standard way to
implement this. There is a comment included in the code that claims the
chip ID register also contains the right input volume, however this is
clearly not the case from the rest of the driver. Further investigation
reveals exactly the same comment in the wm8962 driver, where this is the
case, so this is almost certainly a copy and paste error from when the
driver was created.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to the DMIC that needs time to initial after the MCLK is provided, the
field of delay time is implemented by the platform data.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- first slice of the gvt device model (Zhenyu et al)
- compression support for gpu error states (Chris)
- sunset clause on gpu errors resulting in dmesg noise telling users
how to report them
- .rodata diet from Tvrtko
- switch over lots of macros to only take dev_priv (Tvrtko)
- underrun suppression for dp link training (Ville)
- lspcon (hmdi 2.0 on skl/bxt) support from Shashank Sharma, polish
from Jani
- gen9 wm fixes from Paulo&Lyude
- updated ddi programming for kbl (Rodrigo)
- respect alternate aux/ddc pins (from vbt) for all ddi ports (Ville)
* tag 'drm-intel-next-2016-10-24' of git://anongit.freedesktop.org/drm-intel: (227 commits)
drm/i915: Update DRIVER_DATE to 20161024
drm/i915: Stop setting SNB min-freq-table 0 on powersave setup
drm/i915/dp: add lane_count check in intel_dp_check_link_status
drm/i915: Fix whitespace issues
drm/i915: Clean up DDI DDC/AUX CH sanitation
drm/i915: Respect alternate_ddc_pin for all DDI ports
drm/i915: Respect alternate_aux_channel for all DDI ports
drm/i915/gen9: Remove WaEnableYV12BugFixInHalfSliceChicken7
drm/i915: KBL - Recommended buffer translation programming for DisplayPort
drm/i915: Move down skl/kbl ddi iboost and n_edp_entires fixup
drm/i915: Add a sunset clause to GPU hang logging
drm/i915: Stop reporting error details in dmesg as well as the error-state
drm/i915/gvt: do not ignore return value of create_scratch_page
drm/i915/gvt: fix spare warnings on odd constant _Bool cast
drm/i915/gvt: mark symbols static where possible
drm/i915/gvt: fix sparse warnings on different address spaces
drm/i915/gvt: properly access enabled intel_engine_cs
drm/i915/gvt: Remove defunct vmap_batch()
drm/i915/gvt: Use common mapping routines for shadow_bb object
drm/i915/gvt: Use common mapping routines for indirect_ctx object
...
The ak4641 driver only has a few register defines. As they are only used in
the one main driver file there is not really a need to keep them in a
separate header.
Moving them to the main source file allows to remove the now empty header
file completely.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The last user was removed in commit 4f534777c1 ("ASoC: ak4641: Convert to
direct regmap API usage").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. This driver was merged after the change of DAIs are
matched was made and the IDs were never used and presumably never will be,
so remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The es8328 drivers seems to have used the wm8753 driver as a template. Its
header file contains a few defines that are copied verbatim from the wm8753
header that do not really apply to this driver and are unused. So remove
those defines. This seems safe as they deal with PLL and clock divider
settings and the es8328 driver neither implements a set_pll() nor a
set_clkdiv() callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
This also means the wm9705.h file no longer has any content and can be
removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. These particular IDs were never used and presumably
never will be, so remove them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used for matching instead and the
defines are unused. The last user of these defines was removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support"). So
remove the defines as well.
This also means the wm9712.h file no longer has any content and can be
removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a power saving mechanism in rt5670. It will turn off some
unused power when MCLK is not present. We call that "MCLK detection"
and it should be enabled by default.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a power saving mechanism in rt5640. It will turn off some
unused power when MCLK is not present. We call that "MCLK detection"
and it should be enabled by default.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the wm8581 codec to the wm8580 driver.
The wm8581 codec hardware adds a fourth DAC and otherwise is
compatible with the wm8580 codec.
of_device_id data is used to allow the driver to select the
suitable DAC count specified in the device tree codec selection.
The wm8580_driver_data struct is used to store the number of DACs.
The snd_soc_dai_driver no longer lists the channels_max for the
playback substream. This variable is set during the i2c probe
from the of_device_id supplied wm8580_driver_data struct.
With knowledge of the number of DACs in use, the DAC4 controls,
widgets and routes are added as required for DAC4.
The device tree documentation for the wm8580 is altered to list
the wm8581 codec support, as is the Kconfig file.
Signed-off-by: Matt Flax <flatmax@flatmax.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a power saving mechanism in rt5660. It will turn off some
unused power when MCLK is not present. We call that "MCLK detection"
and it should be enabled by default.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts(Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Digital part of the Codec which is integrated
into Application Processor.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd codec is found in Qualcomm msm8916 and apq8016 processors.
This codec IP is split in to two parts (Digital & Analog).
Analog part is integrated in to PMIC PM8916 and the digital part is
integrated into Application processor. Data transfer between Analog and
Digital Die is done via a internal bus called PDM.
This patch adds support to Analog part of the Codec which is integrated
into PMIC PM8916.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "rt5668" codec supported in this driver is actually a revision
of "rt5663". So the patch is renamed to "rt5663 v2"
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove
the wrappers.
Also use snd_soc_update_bits() where appropriate.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the wm9712 driver still uses custom snd_soc_codec_driver IO
callbacks. This has been deprecated for a while, so convert the wm9705
driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
enable the source clocks for FLLs as they are powered up.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst ultimately we would like to move all the clocking over to the
clock framework, as an intermediate step to get people going for now
gating the source clocks for SYSCLK/ASYNCCLK when they are configured
to come directly from an MCLK pin.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt298_jack_detect may be called before card is instantiated. And
snd_soc_dapm_force_enable_pin will not work in that case. So, update
bit manually by regmap_update_bits.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove
the wrappers. Also use snd_soc_update_bits() were appropriate.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the wm9712 driver still uses custom snd_soc_codec_driver IO
callbacks. This has been deprecated for a while, so convert the wm9712
driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial commit of the Cirrus Logic cs35l34 8V boosted class D
amplifier.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We increment "i" before printing the debug statement. That makes it
the wrong sleep_time[] information and Smatch complains that the last
increment could be beyond the end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's been over two months, git definitely lost it's marbles. Conflicts
resolved by picking our version, plus manually checking the diff with
the parent in drm-intel-next-queued to make sure git didn't do
anything stupid. It did, so I removed 2 occasions where it
double-inserted a bit of code. The diff is now just
- kernel-doc changes
- drm format/name changes
- display-info changes
so looks all reasonable.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Mismatching stream names in DAPM route and widget definitions are
causing compilation errors. Fixing these names allows the cs4270
driver to compile and function.
[Errors must be at probe time not compile time -- broonie]
Signed-off-by: Murray Foster <mrafoster@gmail.com>
Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Currently on some headsets slight pops can be heard during DAPM
power-up/down. This can also be witnessed during the HP detect
procedure. This patch addresses the issue by adjusting DAPM power
sequencing slightly, the introduction of delays and use of
minimum HP gain to avoid such noise artefacts.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The set_bias_level toggles the PDN signal when entering
SND_SOC_BIAS_STANDBY and SND_SOC_BIAS_OFF. However this has no effect and
actually breaks things down (tested with TAS5717) due to the following
reasons:
1) holding down PDN does not save power but holding down RST does
2) now hard mute via register 0x5 is implemented and therefore it is no
longer needed to toggle PDN to enter all channel shut down
3) in order to leave PDN it is required to toggle the RST signal (see
TAS5721 datasheet), which was not implemented
4) toggling PDN as implemented actually mutes PWMs and there is no audio
output (tested on TAS5717)
For these reasons remove the PDN signal toggling and just initialize it to
inactive in probe().
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
TAS5721 datasheet recommends to wait at least 13.5ms after deasserting the
RESET signal. For TAS5717 this time is only 12ms, which was the original
value in the code.
Extend the wait time after deasserting RESET from 12 to 13.5ms to comply
with the TAS5721 specification.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel 1 and 2 Mixer Volume controls (registers 0x72/0x73 and 0x76/0x77)
were wrongly assigned to tas5711_controls in commit f252d2346022
("ASoC: tas571x: add input channel mixer for TAS5717/19")
Therefore move them to tas5717_controls.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Wait extra 50ms after writing the oscillator trim register in probe(), as
recommended by the TAS5721 and TAS5711 datasheets.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse reports a below warning.
sound/soc/codecs/da7219.c:804:57: warning: dubious: x & !y
The line includes a condition statement; '(a < b) & !c'. Practically, the
evaluated value of this statement equals to the value of '(a < b) && !c'.
Although, it's not an usual way to use bitwise operations as logical
operations to several conditions.
This commit fixes the bug.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This hardware supports only 2-channel DAI, even mono ADC digital output
has two channels with the same data.
Having min_channels=1 results in broken playback of mono files in setups
where CPU DAI supports mono.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As long as reading datasheet of STAC9766/9767, this driver includes wrong
usage of DECLARE_TLV_DB_LINEAR().
In "8.1.2. Master Volume Registers", attenuation of lineout volumes is
represented in 5 bits by -1.5 dB/step from 0 to -46.5 dB. Thus,
'master_tlv' should be dB step representation.
In "8.1.14. Record Gain", gain of volumes is represented in 4 bits by
1.5 dB/step from 0 to 22.5 dB. Thus, 'record_tlv' should be dB step
representation.
In "8.1.5. PC BEEP Volume", attenuation of volume is represented in 4 bits
by -3 dB/step from 0 to 45 dB. Thus, 'beep_tlv' should be dB step
representation.
In "8.1.7. Stereo or Mic Volume" and so on, gain of volumes is represented
in 5 bits by -1.5 dB from 12 to -34.5 dB. Thus, 'mix_tlv' should be dB
step representation.
Totally, current implementation includes misuse of TLV-related macro.
This commit replaces usage of DECLARE_TLV_DB_LINEAR() with
SNDRV_CTL_TLVD_DECLARE_DB_SCALE(), to give proper information to
applications in user land.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver has some unused variables. They should be removed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As long as reading datasheet of WM8991, this driver includes wrong usage
of DECLARE_TLV_DB_LINEAR().
In "Table 6 Input PGA Volume Range", volume is represented in 5 bits by
1.5 dB/step between -16.5/30.0 dB. Thus, 'in_pga_tlv' should be dB step
representation.
In "Table 34 LOMIX and ROMIX Volume Range", volume is represented in three
bits by -3 dB/step from 0 to -21 dB. Thus, 'out_mix_tlv' should be dB step
represenation.
In "Table 36 LOPGA, ROPGA, LOUT, ROUT and SPKVOL Volume Range", volume is
represented in 7 bits by 1 dB/step from -73 to 6 dB, including mute. Thus,
'out_pga_tlv' should be dB step representation.
In "Table 26 Digital Volume Range", volume is represented in 8 bits by
3/8 dB/step from -71.625 to 0 dB. Thus, 'out_dac_tlv' should be dB step
representation.
In "Table 16 ADC Digital Volume Range", volume is represented in 8 bits by
3/8 dB/step from -71.625 to 17.625 dB. Thus, 'in_adc_tlv' should be dB step
representation.
In "Table 23 Digital Sidetone Volume", volume is represented in 5 bits by
3 dB/step from -36 to 0 dB. Thus, 'out_sidetone_tlv' should be dB step
representation.
In "Table 12 Left Input Mixer Volume Control", volume is represented in
3 bits by 3 dB/step from -12 to 6 dB
Totally, current implementation includes misuse of TLV-related macro.
This commit replaces usage of DECLARE_TLV_DB_LINEAR() with proper macros,
to give proper information to applications in user land.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Richard Fitzgerald