an 'unhandled fault' is causes when a gadget driver calls
usb_gadget_connect() while the USB cable isn't plugged into
the OTG port.
the fault is caused by an access to MUSB's memory space
while its clock is turned off due to pm_runtime kicking
in.
in order to fix the fault, we enclose musb_gadget_pullup()
with pm_runtime_get_sync() ... pm_runtime_put() calls to
be sure we will always reach that path with clock turned on.
[ balbi@ti.com : simplified commit log; removed few things
which didn't belong there ]
Cc: stable@kernel.org
Reported-by: Zach Pfeffer <zach.pfeffer@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (115 commits)
EHCI: fix direction handling for interrupt data toggles
USB: serial: add IDs for WinChipHead USB->RS232 adapter
USB: OHCI: fix another regression for NVIDIA controllers
usb: gadget: m66592-udc: add pullup function
usb: gadget: m66592-udc: add function for external controller
usb: gadget: r8a66597-udc: add pullup function
usb: renesas_usbhs: support multi driver
usb: renesas_usbhs: inaccessible pipe is not an error
usb: renesas_usbhs: care buff alignment when dma handler
USB: PL2303: correctly handle baudrates above 115200
usb: r8a66597-hcd: fixup USB_PORT_STAT_C_SUSPEND shift
usb: renesas_usbhs: compile/config are rescued
usb: renesas_usbhs: fixup comment-out
usb: update email address in ohci-sh and r8a66597-hcd
usb: r8a66597-hcd: add function for external controller
EHCI: only power off port if over-current is active
USB: mon: Allow to use usbmon without debugfs
USB: EHCI: go back to using the system clock for QH unlinks
ehci: add pci quirk for Ordissimo and RM Slate 100 too
ehci: refactor pci quirk to use standard dmi_check_system method
...
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
udc-core checks for valid callbacks so there is no need for the driver
to do so. Also "can-be-bound-once" is verified by udc-core. The pull-up
callback is called by udc-core afterwords.
[ balbi@ti.com : keep holding gadget_driver pointer for now
remove the stupid check for gadget_driver otherwise
we don't handle IRQs ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the MUSB IP is always OTG, so there's no point
in adding so many ifdefs on the code. Drop those
and always compile the driver for OTG support.
This also allows us to drop the useless "driver
mode" choice. For doing that, we need to make
musb depend on both Host and Peripheral side.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
peripheral drivers are using usb_add_gadget()/usb_del_gadget() to
register/unregister to the udc-core.
The udc-core will take the first available gadget driver and attach
function driver which is calling usb_gadget_register_driver(). This is
the same behaviour we have right now.
Only dummy_hcd was tested, the others were compiled tested.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Pavankumar Kondeti <pkondeti@codeaurora.org>
Cc: Roy Huang <roy.huang@analog.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Cc: Xiaochen Shen <xiaochen.shen@intel.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: cxie4 <cxie4@marvell.com>
Cc: linux-geode@lists.infradead.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes mis-use of MUSB's hardware feature where it won't
flush FIFOs when TXPKTRDY flag was set before and we are
flushing setting both FLUSHFIFO and TXPKTRDY.
In other words, we need to ensure that when we try to
flush FIFOs, we don't accidentaly set TXPKTRDY bit too
due to a read-back of the register.
The MUSB Programming Guide says "May be set simultaneously
with TxPktRdy to abort the packet that is currently being
loaded into the FIFO". This is a situation where TXPKTRDY
hasn't been set yet, but some data already loaded into the
fifo. It looks, that if TXPKTRDY has been set before, and
there is no loading in progress, but we set FLUSHFIFO with
the TXPKTRDY, controller tries to use the same logic to
abort loading and as the result just does nothing (because
there is no packet been loaded currently)
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
[ balbi@ti.com : fixed one whitespace git complained about
improved the commit log slightly ]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Although U8500 and U5500 platforms use paltform dma, Inventra dma specific code
can work for them for the most part. Only difference is for the Rx path where
this patch is making use of request->short_not_ok to select dma mode.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We have a generic way of enabling/disabling
different debug messages on a driver called
DYNAMIC_PRINTK. Anyone interested in enabling
just part of the debug messages, please read
the documentation under:
Documentation/dynamic-debug-howto.txt
for information on how to use that great
infrastructure.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 3dacdf11 "usb: factor out state_string() on otg drivers"
broke building musb drivers since there is already another
otg_state_string() function in musb drivers, but with different
prototype. Fix musb drivers to use common otg_state_string(), too.
Also provide a nop for otg_state_string() if CONFIG_USB_OTG_UTILS
is not defined.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If cable is not connected to peripheral only board when initializing the
gadget driver, then runtime pm calls are out-of-sync and the musb cannot
idle with omap2430.c. This was noted on Nokia N900 where musb prevented the
CPU to be able to enter deeper retention idle state.
This was working in 2.6.38 before runtime pm conversions but there musb
smart standby/idle modes were configured statically where they are now
updated runtime depending on use and cable status.
Reason for out-of-sync is that runtime pm is activated in function
musb_gadget.c: usb_gadget_probe_driver but suspended only in OTG mode if
cable is not connected when initializing. In peripheral only mode this leads
to out-of-sync runtime pm since runtime pm remain active and is activated
another time in omap2430.c: musb_otg_notifications for VBUS Connect event
and thus cannot suspend for VBUS Disconnect event since the use count remains
active.
Fix this by moving cable status check and pm_runtime_put call in
usb_gadget_probe_driver out of is_otg_enabled block.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We are now using our own list_head, so we should
be checking against that, not the gadget driver's
list_head.
Signed-off-by: Felipe Balbi <balbi@ti.com>
On the completion of tx dma, dma is disabled by clearing MUSB_TXCSR_DMAENAB in
TXCSR. If MUSB_TXCSR_AUTOSET was set in txstate() it will remain set although
it is not needed in PIO mode. Clear it as soon as it is not needed.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There was conflict while merging 2 patches. Enabling vbus code
is wrongly moved to error check if loop.
This is a fix to resolve the merge issue.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch supports the retention and offmode support in the idle path for
musb driver using runtime pm APIs.
This is restricted to support offmode and retention only when device not
connected.When device/cable connected with gadget driver loaded,configured
to no idle/standby which will not allow the core transition to retention
or off.
There is no context save/restore done by hardware for musb in OMAP3
and OMAP4,driver has to take care of saving and restoring the context
during offmode.
Musb has a requirement of configuring sysconfig register to force
idle/standby mode and set the ENFORCE bit in module STANDBY register
for retention and offmode support.
Runtime pm and hwmod frameworks will take care of configuring to force
idle/standby when pm_runtime_put_sync is called and back to no
idle/standby when pm_runeime_get_sync is called.
Compile, boot tested and also tested the retention in the idle path on
OMAP3630Zoom3. And tested the global suspend/resume with offmode enabled.
Usb basic functionality tested on OMAP4430SDP.
There is some problem with idle path offmode in mainline, I could not test
with offmode. But I have tested this patch with resetting the controller
in the idle path when wakeup from retention just to make sure that the
context is lost, and restore path is working fine.
Removed .suspend/.resume fnction pointers and functions because there
is no need of having these functions as all required work is done
at runtime in the driver.
There is no need to call the runtime pm api with glue driver device
as glue layer device is the parent of musb core device, when runtime apis
are called for the child, parent device runtime functionality
will be invoked.
Design overview:
pm_runtime_get_sync: When called with musb core device takes care of
enabling the clock, calling runtime callback function of omap2430 glue
layer, runtime call back of musb driver and configure the musb sysconfig
to no idle/standby
pm_runtime_put: Takes care of calling runtime callback function of omap2430
glue layer, runtime call back of musb driver, Configure the musb sysconfig
to force idle/standby and disable the clock.
During musb driver load: Call pm_runtime_get_sync.
End of musb driver load: Call pm_runtime_put
During gadget driver load: Call pm_runtime_get_sync,
End of gadget driver load: Call pm_runtime_put if there is no device
or cable is connected.
During unload of the gadget driver:Call pm_runtime_get_sync if cable/device
is not connected.
End of the gadget driver unload : pm_runtime_put
During unload of musb driver : Call pm_runtime_get_sync
End of unload: Call pm_runtime_put
On connect of usb cable/device -> transceiver notification(VBUS and ID-GND):
pm_runtime_get_sync only if the gadget driver loaded.
On disconnect of the cable/device -> Disconnect Notification:
pm_runtime_put if the gadget driver is loaded.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit ad1adb89a0
(usb: musb: gadget: do not poke with gadget's list_head)
fixed a bug in musb where it was corrupting the list_head
which is supposed to be used by gadget drivers. While
doing that, I forgot to fix the usage in musb_gadget_dequeue()
method. Fix that.
Reported-by: Pavol Kurina <pavol.kurina@emsys.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the gadget code, there are several DBG() macro invocations that explicitly
print the calling function's name while DBG() macro itself does this anyway;
most of these were added by commit f11d893de4
(usb: musb: support ISO high bandwidth for gadget mode). Remove the duplicated
printing, somewhat clarifying the messages at the same time...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
OMAP4430 is embedded with UTMI PHY. This PHY does not support the
OTG features like ID pin detection and VBUS detection. This function
is exported to an external companion chip TWL6030. Software must retrieve
the OTG HNP and SRP status from the TWL6030 and configure the bits inside
the control module that drive the related USBOTGHS UTMI interface signals.
It must also read back the UTMI signals needed to configure the TWL6030
OTG module.
Can find more details in the TRM[1].
[1]:http://focus.ti.com/pdfs/wtbu/OMAP4430_ES2.0_Public_TRM_vJ.pdf
In OMAP4430 musb driver VBUS and ID notifications are received from the
transceiver driver. If the cable/device is connected during boot,
notifications from transceiver driver will be missed till musb driver
is loaded.
Patch to configure the transceiver in the platform_enable/disable
functions and enable the vbus in the gadget driver based on the
last_event of the otg_transceiver.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct usb_request's list_head is supposed to be
used only by gadget drivers, but musb is abusing
that. Give struct musb_request its own list_head
and prevent musb from poking into other driver's
business.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just a few cosmetic fixes to usb_gadget_probe_driver()
and usb_gadget_unregister_driver().
Decreased a few indentation levels with goto statements.
While at that, also add the missing call to musb_stop().
If we don't have OTG, there's no point of leaving
MUSB prepared for operation if a gadget driver fails
to probe. The same is valid for usb_gadget_unregister_driver(),
since we are removing the gadget driver and we don't have
OTG, we can completely unconfigure MUSB.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gadget MUSB driver handles dma mappings in musb_gadget_queue(). Where as it is
possible for dma code to reject the usb request later at ->channel_program()
called from txstate()/rxstate()
For example ->channel_program in tusb6010_omap.c:
static int tusb_omap_dma_program(struct dma_channel *channel, u16 packet_sz,
u8 rndis_mode, dma_addr_t dma_addr, u32 len)
{
...
if (unlikely(dma_addr & 0x1) || (len < 32) || (len > packet_sz))
return false;
...
if (dma_addr & 0x2)
return false;
...
}
In this case, usb request will be handled in PIO mode which renders dma mapping
operations unnecessary.
This patch adds an api to allow dma code to indicate incompatibility with usb
request. Gadget musb driver call this api, if available, before dma mappings to
avoid any unnecessary mapping operations.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If dma buffers are mapped by a higher layer, with a boolean musb_request.mapped
it is still possible to call dma_sync_single_for_device() from
musb_g_giveback(), even if txstate()/rxstate() has called unmap_dma_buffer()
before falling back to pio mode.
Moreover, check for musb_ep->dma is moved within map_dma_buffer() so where
applicable checks for it are removed. And where possible, checks for
is_dma_capable() are merged with buffer map state check.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We know that blackfin doesn't support double
buffering feature as of today. So we add a
flag set by musb_platform_init() to forcefully
disable that feature.
Such flag is created and marked as deprecated
to force us to find a solution for the missing
double buffering support on blackfin.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
The Inventra DMA engine used with the MUSB controller in many
SoCs cannot use DMA for control transfers on EP0, but can use
DMA for all other transfers.
The USB core maps urbs for DMA if hcd->self.uses_dma is true.
(hcd->self.uses_dma is true for MUSB as well).
Split the uses_dma flag into two - one that says if the
controller needs to use PIO for control transfers, and
another which says if the controller uses DMA (for all
other transfers).
Also, populate this flag for all MUSB by default.
(Tested on OMAP3 and OMAP4 boards, with EHCI and MUSB HCDs
simultaneously in use).
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Praveena NADAHALLY <praveen.nadahally@stericsson.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fixes below compilation warning when musb driver is compiled for
PIO mode:
drivers/usb/musb/musb_gadget.c: In function 'musb_g_rx':
drivers/usb/musb/musb_gadget.c:840:
warning: label 'exit' defined but not used
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If RXCSR_AUTOCLEAR flag is not cleard before PIO reading, one packet
may be recieved by musb fifo, but no chance to notify
software, so cause packet loss, follows the detailed process:
- PIO read one packet
- musb fifo auto clear the MUSB_RXCSR_RXPKTRDY
- musb continue to recieve the next packet, and MUSB_RXCSR_RXPKTRDY
is set
- software clear the MUSB_RXCSR_RXPKTRDY, so there is no chance for
musb to notify software that the 2nd recieved packet.
The patch does fix the g_ether issue below:
- use fifo_mode 3 to enable double buffer
- 'ping -s 1024 IP_OF_BEAGLE_XM'
- one usb packet of 512 byte is lost, so ping failed,
which can be observed by wireshark
note:
Beagle xm takes musb rtl1.8 and may fallback to pio mode
for unaligned buffer.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Buffer is mapped to dma when dma channel is
allocated. If, for some reason, dma channel
programming fails, musb code will fallback
to PIO mode to transfer that request. In
that case, we need to unmap the buffer
back to CPU.
MUSB RTL1.8 and above cannot handle buffers
which are not 32bit aligned. That happens to
every request sent by g_ether gadget
driver. Since the buffer sent was unaligned,
we need to fallback to PIO.
Because of that, g_ether was failing due
to missing buffer unmapping.
With this patch and [1] g_ether works fine
with all MUSB revisions.
Verified with OMAP3630 board, which has
MUSB RTL1.8 using g_ether and g_zero.
[1] http://www.spinics.net/lists/linux-usb/msg38400.html
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_gadget_queue() checks for '!req->buf' condition twice:
in the second case the code is both duplicated and unreachable
as the first check returns early.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 9f445cb29918dc488b7a9a92ef018599cce33df7[USB: musb: disable
double buffering for older RTL versions] tries to disable double
buffer mode by writing endpoint hw max packet size to TXMAP/RXMAP.
First the approach can break full speed and cause overflow problems.
We should always set those registers with the actual max packet size
from endpoint descriptor.
Second, the problem describe by commit 9f445cb299
was caused by musb gadget driver; nothing to do with RTL revision as
originaly suspected.
The real fix to the problem is to always use actual max packet
size from endpoint descriptor to config TXMAP/RXMAP registers.
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In function musb_gadget_setup() call put_device()
when device_register() fails.
Signed-off-by: Rahul Ruikar <rahul.ruikar@gmail.com>
Acked-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
1, In Rx double buffer case, FIFO may have two packets, so
rxstate should be called to unload fifo if RXPKTRDY is set
even the current request has not been completed.
2, Commit 633ba7876b96ec339ef685357e2f7c60b5a8ce85
introduces autoclear to support double buffer in dma mode 0,
so remove clearing RXPKTRDY manually for dma mode 0.
3, Commit c7af6b29ffeffbeb28caf39e5b2ce29b11807c7d may break
dma mode 1 for non-doublebuffer endpoint, fix it.
With this patch, either usbtest #5 or g_file_storage(writing
file to device in usb host) or g_ether have been tested OK in
double buffer case(using fifo mode 3). Also, this patch has
been verified that single buffer case can't be broken.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 633ba7876b96ec339ef685357e2f7c60b5a8ce85 broke
g_file_storage functionality by enabling AUTOCLEAR on
all cases without caring for all gadget drivers.
This patch will only enable AUTOCLEAR if our endpoint's
FIFO was configured with double buffering support. Note
this is not a complete fix, double buffered case still
doesn't work always, but that hasn't been working for
quite some time. Other than reverting the entire commit
and breaking testusb with double buffered case again,
I decided it was better to fix the single buffered case
and spend more time fixing double buffered case properly.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem reported by Sergei:
>how come? we need to send ZLP before giving back the request.
>Well, look at the code ionce again. We need to send ZLP *after*
>request->actual == request->length, but as the check is inserted
>after the ZLP send, ZLP *may* be sent once the first DMA completes,
>not the last.
The patch also has been discussed on the link below:
http://marc.info/?t=128454814900001&r=1&w=2
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reported-by: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
musb_g_rx() always returns if next_request() call yields NULL, so the DBG()
near the function's end can never be invoked. Remove it along with unneeded
'return'; also remove the duplicate 'request' check...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch has been tested OK on beagle B5 board and
use usbtest #15 and #16 as testcase.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To accomplish this the function to register a gadget driver takes the bind
function as a second argument. To make things clearer rename the function
to resemble platform_driver_probe.
This fixes many section mismatches like
WARNING: drivers/usb/gadget/g_printer.o(.data+0xc): Section mismatch in
reference from the variable printer_driver to the function
.init.text:printer_bind()
The variable printer_driver references
the function __init printer_bind()
All callers are fixed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[m.nazarewicz@samsung.com: added dbgp]
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 46034dca51 (USB: musb_gadget_ep0: stop
abusing musb_gadget_set_halt()) forgot to restart a queued request after
clearing the endpoint halt feature. This results in a couple of USB resets
while enumerating the file-backed storage gadget due to CSW packet not being
sent for the MODE SENSE(10) command.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DMA length should not go beyond the availabe space
of request buffer, so fix it.
Also set max_len of cppi dma channel as max size of
int type, so make musb dma handling happier.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Complete the current request only if the data transfer is over.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DMA length should not go beyond the availabe space of request buffer,
so fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes one bugs of OUT transfer in double buffer case:
-the current code only enable autoclear for dma mode 1, and not
for dma mode 0
Without this patch, test #5 of usbtest can't be passed if we
configure musb as g_zero and use fifo mode 3 to enable double
buffer mode.
With this patch and the following patch(fix dma length),
on my beagle B5, test#5(queued bulk out) may go beyond
18Mbyte/s(seems dma mode 0 is quicker in double buffer case)
if musb is configured as g_zero and fifo mode 3 is taken, follows
the test command:
#./testusb -D DEV_NAME -c 1024 -t 5 -s 32768 -g 8 [1]
Also I have tested this patch can't make g_ether broken.
[1],source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes one infinite hang of bulk IN transfer in double buffer
case, the hang can be observed easily by test #6 of usbtest if musb is
configured as g_zero and fifo mode 3 is taken to enable double fifo.
In fact, the patch only removes the check for non-empty fifo before
loading data from new request into fifo since the check is not correct:
-in double buffer case, fifo may accommodate more than one packet,
even though it has contained one packet already and is non-empty
-since last DMA is completed before calling musb_g_tx, it is sure
that fifo may accommodate at least one packet
Without applying the patch, new requst enqueued from .complte may not
have a chance to be loaded into fifo, then will never be completed and
cause infinite hangs.
With the patch, on my beagle B5, test#6(queued bulk in) can be passed and
test result may go beyond 33Mbyte/s if musb is configured as g_zero and
fifo mode 3 is taken, follows the test command:
#testusb -D DEV_NAME -c 1024 -t 6 -s 32768 -g 8 [1]
[1],
-source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
John Stultz