Since the drivers/ieee1394/ backend was removed from firedtv, its I/O no
longer needs to be abstracted as exchangeable backend methods.
Also, ieee1394 variants of module and device probe and removal are no
longer there. Move module probe and removal into firedtv-fw.c where
device probe and removal are implemented.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/ieee1394/ has been removed in Linux 2.6.37. The corresponding
backend code in firedtv is no longer built in now and can be deleted.
Firedtv continues to work with drivers/firewire/.
Also, fix a Kconfig menu comment: Removal of CONFIG_IEEE1394 made the
"Supported FireWire (IEEE 1394) Adapters" comment disappear; bring it back
with corrected dependency.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a portability fix and reduces stack usage.
The DMA mapping API cannot map on-stack addresses, as explained in
Documentation/DMA-mapping.txt. Convert the two cases of on-stack packet
payload buffers in firedtv (payload of write requests in avc_write and
of lock requests in cmp_lock) to slab-allocated memory.
We use the 512 bytes sized FCP frame buffer in struct firedtv for this
purpose. Previously it held only incoming FCP responses, now it holds
pending FCP requests and is then overwriten by an FCP response from the
tuner subunit. Ditto for CMP lock requests and responses. Accesses to
the payload buffer are serialized by fdtv->avc_mutex.
As a welcome side effect, stack usage of the AV/C transaction functions
is reduced by 512 bytes.
Alas, avc_register_remote_control() is a special case: It previously
did not wait for a response. To fit better in with the other FCP
transactions, let it wait for an interim response.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All read transactions initiated by firedtv are only quadlet-sized, hence
the backend->read call can be simplified a little.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The firedtv DVB driver will now work not only on top of the old ieee1394
driver stack but also on the new firewire driver stack.
Alongside to the firedtv-1394.c backend for driver binding and I/O, the
firedtv-fw.c backend is added. Depending on which of the two 1394
stacks is configured, one or the other or both backends will be built
into the firedtv driver.
This has been tested with a DVB-T and a DVB-C box on x86-64 and x86-32
together with a few different controllers (Agere FW323, a NEC chip, TI
TSB82AA2, TSB43AB22/A, VIA VT6306).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Preparation for the port of firedtv to the firewire-core kernel API:
The fdtv->backend->lock() hook and thus the CMP code is slightly changed
to better fit with the new API.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Combination of the following changes:
Mon, 23 Feb 2009 14:21:10 +0100 (CET)
firedtv: reinstate debug logging option
Henrik Kurelid tells me that FCP debug logging (which I removed during
cleanups) is still useful when working on driver issues together with
end users. So bring it back in an updated form with only 60% of the
original code footprint.
Logging can be enabled with
# echo -1 > /sys/module/firedtv/parameters/debug
1 instead of -1 enables only FCP header logging,
2 instead of -1 enables only hexdumps of the entire FCP frames.
0 switches logging off again.
Fri, 20 Feb 2009 20:54:27 +0100 (CET)
firedtv: build fix for INPUT=m and DVB_FIREDTV=y
Thu, 19 Feb 2009 20:40:39 +0100
firedtv: use msecs_to_jiffies
Pointed out by Mauro Carvalho Chehab.
Sun Feb 15 20:50:46 CET 2009
firedtv: some more housekeeping
Fix an old checkpatch warning and a new compiler warning.
Sun Feb 15 15:33:17 CET 2009
firedtv: rename a file once more
At the moment, about a third of avc.c is specific to FireDTVs rather
than generic AV/C code. Rename it to firedtv-avc.c.
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: more compact channels backing store
Replace struct firedtv_channel { bool active; int pid; } channel[16];
by unsigned long channel_active; u16 channel_pid[16];.
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: some simplifications
c->active was unnecessarily cleared twice.
Also, by marking the channel inactive before the for loop,
the loop becomes identical with fdtv_channel_collect().
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: remove a bogus loop
This loop is unnecessary because
- only active channel[].pid's will be sent to the device,
- when a channel is activated, its pid is set to dvbdmxfeed->pid.
Perhaps the original code was there because it was initially not fully
covered by the fdtv->demux_mutex.
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: fix mutex protection
fdtv_start_feed() accessed the channel list unsafely.
Fully serialize it with itself and fdtv_stop_feed().
Sun Feb 15 15:33:17 CET 2009
firedtv: dvb demux: fix missing braces
Original code was:
...
case DMX_TS_PES_OTHER:
//Dirty fix to keep firesat->channel pid-list up to date
for(k=0;k<16;k++){
if(firesat->channel[k].active == 0)
firesat->channel[k].pid =
dvbdmxfeed->pid;
break;
}
channel = firesat_channel_allocate(firesat);
break;
default:
...
Looks bogus in several respects. For now let's just add braces to the if
because that seems to be what the author meant.
Sun Feb 15 15:33:17 CET 2009
firedtv: allow build without input subsystem
!CONFIG_INPUT is very unlikely on systems on which firedtv is of
interest. But we can easily support it.
Sun Feb 15 15:33:17 CET 2009
firedtv: replace EXTRA_CFLAGS by ccflags
The former are deprecated.
The latter can depend on Kconfig variables.
Sun Feb 15 15:33:17 CET 2009
firedtv: concentrate ieee1394 dependencies
Move the entire interface with drivers/ieee1394 to firedtv-1394.c.
Move 1394-independent module initialization code to firedtv-dvb.c.
This prepares interfacing with drivers/firewire.
Sun Feb 15 15:33:17 CET 2009
firedtv: amend Kconfig menu prompt
Sun Feb 15 15:33:17 CET 2009
firedtv: remove kernel version compatibility macro
Sun Feb 15 15:33:17 CET 2009
firedtv: combine header files
avc.h and firedtv-*.h are small and currently not shared with other
drivers, hence concatenate them all into firedtv.h.
Sun Feb 15 15:33:17 CET 2009
firedtv: misc style touch-ups
Standardize on lower-case hexadecimal constants. Adjust whitespace.
Omit unnecessary pointer type casts and an unnecessary list head
initialization. Use dev_printk.
Wed Feb 11 21:21:04 CET 2009
firedtv: avc, ci: remove unused constants
Wed Feb 11 21:21:04 CET 2009
firedtv: avc: remove bitfields from read descriptor response operands
Don't use bitfields in struct types of on-the-wire data.
Wed Feb 11 21:21:04 CET 2009
firedtv: avc: remove bitfields from DSD command operands
Don't use bitfields in struct types of on-the-wire data.
Wed Feb 11 21:21:04 CET 2009
firedtv: avc: header file cleanup
Remove unused constants and declarations.
Move privately used constants into .c files.
Wed Feb 11 21:21:04 CET 2009
firedtv: avc: remove bitfields from FCP frame types
Don't use bitfields in struct types of on-the-wire data.
Also move many privately used constants from avc.h to avc.c
and remove some unused constants.
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: avc: fix offset in avc_tuner_get_ts
The parentheses were wrong. It didn't matter though because this code
only writes a 0 into an area which is already initialized to 0.
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: avc: reduce stack usage, remove two typedefs
It is safe to share a memory buffer for command frame and response frame
because the response data come in after the command frame was last used.
Even less stack would be required if only the actual required frame size
instead of the entire FCP register size was allocated.
Also, rename the defined types AVCCmdFrm and AVCRspFrm to
struct avc_command_frame and struct avc_response_frame.
TODO: Remove the bitfields in these types.
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: cmp: move code to avc
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: iso: move code to firedtv-1394
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: iso: remove unnecessary struct type definitions
Sun, 18 Jan 2009 16:30:00 +0100 (CET)
firedtv: iso: style changes and fixlets
Add cleanup after failure in setup_iso_channel.
Replace printk() by dv_err().
Decrease indentation level in rawiso_activity_cb().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Combination of the following changes:
Sat, 17 Jan 2009 14:47:34 +0100
firedtv: rename variables and functions from firesat to firedtv
Signed-off-by: Rambaldi <Rambaldi@xs4all.nl>
Additional changes by Stefan Richter:
Renamed struct firedtv *firedtv to struct firedtv *fdtv and
firedtv_foo_bar() to fdtv_foo_bar() for brevity.
Sat, 17 Jan 2009 13:07:44 +0100
firedtv: rename files from firesat to firedtv
Signed-off-by: Rambaldi <Rambaldi@xs4all.nl>
Additional changes by Stefan Richter:
Name the directory "firewire" instead of "firedtv".
Standardize on "-" instead of "_" in file names, because that's what
drivers/firewire/ and drivers/media/dvb/dvb-usb/ use too.
Build fix.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter