Commit Graph

2082 Commits

Author SHA1 Message Date
David S. Miller 17f7f4d9fc Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/ipv4/fib_frontend.c
2010-12-26 22:37:05 -08:00
David S. Miller e058464990 Revert "ipv4: Allow configuring subnets as local addresses"
This reverts commit 4465b46900.

Conflicts:

	net/ipv4/fib_frontend.c

As reported by Ben Greear, this causes regressions:

> Change 4465b46900 caused rules
> to stop matching the input device properly because the
> FLOWI_FLAG_MATCH_ANY_IIF is always defined in ip_dev_find().
>
> This breaks rules such as:
>
> ip rule add pref 512 lookup local
> ip rule del pref 0 lookup local
> ip link set eth2 up
> ip -4 addr add 172.16.0.102/24 broadcast 172.16.0.255 dev eth2
> ip rule add to 172.16.0.102 iif eth2 lookup local pref 10
> ip rule add iif eth2 lookup 10001 pref 20
> ip route add 172.16.0.0/24 dev eth2 table 10001
> ip route add unreachable 0/0 table 10001
>
> If you had a second interface 'eth0' that was on a different
> subnet, pinging a system on that interface would fail:
>
>   [root@ct503-60 ~]# ping 192.168.100.1
>   connect: Invalid argument

Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-23 12:03:57 -08:00
Jiri Kosina 4b7bd36470 Merge branch 'master' into for-next
Conflicts:
	MAINTAINERS
	arch/arm/mach-omap2/pm24xx.c
	drivers/scsi/bfa/bfa_fcpim.c

Needed to update to apply fixes for which the old branch was too
outdated.
2010-12-22 18:57:02 +01:00
Eric Dumazet 12b16dadbc filter: optimize accesses to ancillary data
We can translate pseudo load instructions at filter check time to
dedicated instructions to speed up filtering and avoid one switch().
libpcap currently uses SKF_AD_PROTOCOL, but custom filters probably use
other ancillary accesses.

Note : I made the assertion that ancillary data was always accessed with
BPF_LD|BPF_?|BPF_ABS instructions, not with BPF_LD|BPF_?|BPF_IND ones
(offset given by K constant, not by K + X register)

On x86_64, this saves a few bytes of text :

# size net/core/filter.o.*
   text	   data	    bss	    dec	    hex	filename
   4864	      0	      0	   4864	   1300	net/core/filter.o.new
   4944	      0	      0	   4944	   1350	net/core/filter.o.old

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-21 12:30:12 -08:00
Eric Dumazet 70978182d4 net: timestamp cloned packet in dev_queue_xmit_nit
Le vendredi 17 décembre 2010 à 10:26 +0100, Eric Dumazet a écrit :

>
> I think we can add this after latest Changli patch :
>
> He does one skb_clone() before calling the sniffers.
> We could set timestamp on this clone, instead of original skb.
>
> Problem solved.
>

[PATCH net-next-2.6] net: timestamp cloned packet in dev_queue_xmit_nit

Now we do one clone of skb if at least one sniffer might take packet,
we also can do the skb timestamping on the clone and let original packet
unchanged.

This is a generalization of commit 8caf153974 (net: sch_netem: Fix an
inconsistency in ingress netem timestamps.)

This way, we can have a good idea when packets are delivered to our
stack (tcpdump -i ifb0), while a tcpdump on original device gives
timestamps right before ingressing.

This also speedup our stack, avoiding taking timestamps if not needed.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Changli Gao <xiaosuo@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-21 10:50:38 -08:00
Joe Perches 58231186c4 pktgen: Remove unnecessary prefix from pr_<level>
Remove "pktgen: " prefix string from one pr_info.
pr_fmt adds it, so this is a duplicate.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-20 10:30:06 -08:00
Shan Wei 4c306a9291 net: kill unused macros
These macros never be used, so remove them.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-19 21:59:35 -08:00
Changli Gao 71d9dec24d net: increase skb->users instead of skb_clone()
In dev_queue_xmit_nit(), we have to clone skbs as we need to mangle skbs,
however, we don't need to clone skbs for all the packet_types.

Except for the first packet_type, we increase skb->users instead of
skb_clone().

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-19 21:50:20 -08:00
David S. Miller b4aa9e05a6 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/bnx2x/bnx2x.h
	drivers/net/wireless/iwlwifi/iwl-1000.c
	drivers/net/wireless/iwlwifi/iwl-6000.c
	drivers/net/wireless/iwlwifi/iwl-core.h
	drivers/vhost/vhost.c
2010-12-17 12:27:22 -08:00
Michał Mirosław 55508d601d net: Use skb_checksum_start_offset()
Replace skb->csum_start - skb_headroom(skb) with skb_checksum_start_offset().

Note for usb/smsc95xx: skb->data - skb->head == skb_headroom(skb).

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16 14:43:14 -08:00
Octavian Purdila fcbdf09d96 net: fix nulls list corruptions in sk_prot_alloc
Special care is taken inside sk_port_alloc to avoid overwriting
skc_node/skc_nulls_node. We should also avoid overwriting
skc_bind_node/skc_portaddr_node.

The patch fixes the following crash:

 BUG: unable to handle kernel paging request at fffffffffffffff0
 IP: [<ffffffff812ec6dd>] udp4_lib_lookup2+0xad/0x370
 [<ffffffff812ecc22>] __udp4_lib_lookup+0x282/0x360
 [<ffffffff812ed63e>] __udp4_lib_rcv+0x31e/0x700
 [<ffffffff812bba45>] ? ip_local_deliver_finish+0x65/0x190
 [<ffffffff812bbbf8>] ? ip_local_deliver+0x88/0xa0
 [<ffffffff812eda35>] udp_rcv+0x15/0x20
 [<ffffffff812bba45>] ip_local_deliver_finish+0x65/0x190
 [<ffffffff812bbbf8>] ip_local_deliver+0x88/0xa0
 [<ffffffff812bb2cd>] ip_rcv_finish+0x32d/0x6f0
 [<ffffffff8128c14c>] ? netif_receive_skb+0x99c/0x11c0
 [<ffffffff812bb94b>] ip_rcv+0x2bb/0x350
 [<ffffffff8128c14c>] netif_receive_skb+0x99c/0x11c0

Signed-off-by: Leonard Crestez <lcrestez@ixiacom.com>
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16 14:26:56 -08:00
Octavian Purdila 443457242b net: factorize sync-rcu call in unregister_netdevice_many
Add dev_close_many and dev_deactivate_many to factorize another
sync-rcu operation on the netdevice unregister path.

$ modprobe dummy numdummies=10000
$ ip link set dev dummy* up
$ time rmmod dummy

Without the patch           With the patch

real    0m 24.63s           real    0m 5.15s
user    0m 0.00s            user    0m 0.00s
sys     0m 6.05s            sys     0m 5.14s

Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16 14:04:44 -08:00
Changli Gao b236da6931 net: use NUMA_NO_NODE instead of the magic number -1
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16 13:16:06 -08:00
Vladislav Zolotarov a3d22a68d7 bnx2x: Take the distribution range definition out of skb_tx_hash()
Move the calcualation of the Tx hash for a given hash range into a separate
function and define the skb_tx_hash(), which calculates a Tx hash for a
[0; dev->real_num_tx_queues - 1] hash values range, using this
function (__skb_tx_hash()).

Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16 13:15:53 -08:00
Tejun Heo afe2c511fb workqueue: convert cancel_rearming_delayed_work[queue]() users to cancel_delayed_work_sync()
cancel_rearming_delayed_work[queue]() has been superceded by
cancel_delayed_work_sync() quite some time ago.  Convert all the
in-kernel users.  The conversions are completely equivalent and
trivial.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: netdev@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netfilter-devel@vger.kernel.org
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: linux-nfs@vger.kernel.org
2010-12-15 10:56:11 +01:00
Eric Dumazet a19faf0250 net: fix skb_defer_rx_timestamp()
After commit c1f19b51d1 (net: support time stamping in phy devices.),
kernel might crash if CONFIG_NETWORK_PHY_TIMESTAMPING=y and
skb_defer_rx_timestamp() handles a packet without an ethernet header.

Fixes kernel bugzilla #24102

Reference: https://bugzilla.kernel.org/show_bug.cgi?id=24102
Reported-and-tested-by: Andrew Watts <akwatts@ymail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-10 16:20:56 -08:00
Ben Hutchings e596e6e4d5 ethtool: Report link-down while interface is down
While an interface is down, many implementations of
ethtool_ops::get_link, including the default, ethtool_op_get_link(),
will report the last link state seen while the interface was up.  In
general the current physical link state is not available if the
interface is down.

Define ETHTOOL_GLINK to reflect whether the interface *and* any
physical port have a working link, and consistently return 0 when the
interface is down.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-10 15:55:23 -08:00
Junchang Wang a8d764b983 pktgen: adding prefetchw() call
We know for sure pktgen is going to write skb->data right after
*_alloc_skb, causing unnecessary cache misses.

Idea is to add a prefetchw() call to prefetch the first cache line
indicated by skb->data. On systems with Adjacent Cache Line Prefetch,
it's probably two cache lines are prefetched.

With this patch, pktgen on Intel SR1625 server with two E5530
quad-core processors and a single ixgbe-based NIC went from 8.63Mpps
to 9.03Mpps, with 4.6% improvement.

Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-10 15:36:52 -08:00
Eric Dumazet 4bc65dd8d8 filter: use size of fetched data in __load_pointer()
__load_pointer() checks data we fetch from skb is included in head
portion, but assumes we fetch one byte, instead of up to four.

This wont crash because we have extra bytes (struct skb_shared_info)
after head, but this can read uninitialized bytes.

Fix this using size of the data (1, 2, 4 bytes) in the test.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-09 20:47:04 -08:00
Eric Dumazet 68835aba4d net: optimize INET input path further
Followup of commit b178bb3dfc (net: reorder struct sock fields)

Optimize INET input path a bit further, by :

1) moving sk_refcnt close to sk_lock.

This reduces number of dirtied cache lines by one on 64bit arches (and
64 bytes cache line size).

2) moving inet_daddr & inet_rcv_saddr at the beginning of sk

(same cache line than hash / family / bound_dev_if / nulls_node)

This reduces number of accessed cache lines in lookups by one, and dont
increase size of inet and timewait socks.
inet and tw sockets now share same place-holder for these fields.

Before patch :

offsetof(struct sock, sk_refcnt) = 0x10
offsetof(struct sock, sk_lock) = 0x40
offsetof(struct sock, sk_receive_queue) = 0x60
offsetof(struct inet_sock, inet_daddr) = 0x270
offsetof(struct inet_sock, inet_rcv_saddr) = 0x274

After patch :

offsetof(struct sock, sk_refcnt) = 0x44
offsetof(struct sock, sk_lock) = 0x48
offsetof(struct sock, sk_receive_queue) = 0x68
offsetof(struct inet_sock, inet_daddr) = 0x0
offsetof(struct inet_sock, inet_rcv_saddr) = 0x4

compute_score() (udp or tcp) now use a single cache line per ignored
item, instead of two.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-09 20:05:58 -08:00
David S. Miller fe6c791570 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
	net/llc/af_llc.c
2010-12-08 13:47:38 -08:00
Eric Dumazet 15c2d75f49 net: call dev_queue_xmit_nit() after skb_dst_drop()
Avoid some atomic ops on dst refcount, calling dev_queue_xmit_nit()
after skb_dst_drop() in dev_hard_start_xmit().

When queueing a packet into af_packet socket, we drop dst anyway.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-08 10:39:54 -08:00
Eric Dumazet 62ab081213 filter: constify sk_run_filter()
sk_run_filter() doesnt write on skb, change its prototype to reflect
this.

Fix two af_packet comments.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-08 10:30:34 -08:00
Eric Dumazet 941666c2e3 net: RCU conversion of dev_getbyhwaddr() and arp_ioctl()
Le dimanche 05 décembre 2010 à 09:19 +0100, Eric Dumazet a écrit :

> Hmm..
>
> If somebody can explain why RTNL is held in arp_ioctl() (and therefore
> in arp_req_delete()), we might first remove RTNL use in arp_ioctl() so
> that your patch can be applied.
>
> Right now it is not good, because RTNL wont be necessarly held when you
> are going to call arp_invalidate() ?

While doing this analysis, I found a refcount bug in llc, I'll send a
patch for net-2.6

Meanwhile, here is the patch for net-next-2.6

Your patch then can be applied after mine.

Thanks

[PATCH] net: RCU conversion of dev_getbyhwaddr() and arp_ioctl()

dev_getbyhwaddr() was called under RTNL.

Rename it to dev_getbyhwaddr_rcu() and change all its caller to now use
RCU locking instead of RTNL.

Change arp_ioctl() to use RCU instead of RTNL locking.

Note: this fix a dev refcount bug in llc

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-08 10:07:24 -08:00
Changli Gao aa94210411 net: init ingress queue
The dev field of ingress queue is forgot to initialized, then NULL
pointer dereference happens in qdisc_alloc().

Move inits of tx queues to netif_alloc_netdev_queues().

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-08 09:43:27 -08:00
Miloslav Trmač 6f107b5861 net: Add missing lockdep class names for af_alg
Signed-off-by: Miloslav Trmač <mitr@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2010-12-08 14:35:34 +08:00
David Shwatrz 8917a3c0b7 Fix a typo in datagram.c and sctp/socket.c.
Hi,
This patch fixes a typo in net/core/datagram.c and in net/sctp/socket.c

Regards,
David Shwartz

Signed-off-by: David Shwartz <dshwatrz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-06 13:10:11 -08:00
Eric Dumazet 2d5311e4e8 filter: add a security check at install time
We added some security checks in commit 57fe93b374
(filter: make sure filters dont read uninitialized memory) to close a
potential leak of kernel information to user.

This added a potential extra cost at run time, while we can perform a
check of the filter itself, to make sure a malicious user doesnt try to
abuse us.

This patch adds a check_loads() function, whole unique purpose is to
make this check, allocating a temporary array of mask. We scan the
filter and propagate a bitmask information, telling us if a load M(K) is
allowed because a previous store M(K) is guaranteed. (So that
sk_run_filter() can possibly not read unitialized memory)

Note: this can uncover application bug, denying a filter attach,
previously allowed.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: Changli Gao <xiaosuo@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-06 12:59:09 -08:00
Eric Dumazet da2033c282 filter: add SKF_AD_RXHASH and SKF_AD_CPU
Add SKF_AD_RXHASH and SKF_AD_CPU to filter ancillary mechanism,
to be able to build advanced filters.

This can help spreading packets on several sockets with a fast
selection, after RPS dispatch to N cpus for example, or to catch a
percentage of flows in one queue.

tcpdump -s 500 "cpu = 1" :

[0] ld CPU
[1] jeq #1  jt 2  jf 3
[2] ret #500
[3] ret #0

# take 12.5 % of flows (average)
tcpdump -s 1000 "rxhash & 7 = 2" :

[0] ld RXHASH
[1] and #7
[2] jeq #2  jt 3  jf 4
[3] ret #1000
[4] ret #0

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Rui <wirelesser@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-06 12:59:05 -08:00
Michał Mirosław 7903264402 net: Fix too optimistic NETIF_F_HW_CSUM features
NETIF_F_HW_CSUM is a superset of NETIF_F_IP_CSUM+NETIF_F_IPV6_CSUM, but
some drivers miss the difference. Fix this and also fix UFO dependency
on checksumming offload as it makes the same mistake in assumptions.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-06 12:59:04 -08:00
Eric Dumazet 46bcf14f44 filter: fix sk_filter rcu handling
Pavel Emelyanov tried to fix a race between sk_filter_(de|at)tach and
sk_clone() in commit 47e958eac2

Problem is we can have several clones sharing a common sk_filter, and
these clones might want to sk_filter_attach() their own filters at the
same time, and can overwrite old_filter->rcu, corrupting RCU queues.

We can not use filter->rcu without being sure no other thread could do
the same thing.

Switch code to a more conventional ref-counting technique : Do the
atomic decrement immediately and queue one rcu call back when last
reference is released.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-06 09:29:43 -08:00
Changli Gao ca44ac3861 net: don't reallocate skb->head unless the current one hasn't the needed extra size or is shared
skb head being allocated by kmalloc(), it might be larger than what
actually requested because of discrete kmem caches sizes. Before
reallocating a new skb head, check if the current one has the needed
extra size.

Do this check only if skb head is not shared.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-03 10:59:47 -08:00
David S. Miller 493f377d6d tcp: Add timewait recycling bits to ipv6 connect code.
This will also improve handling of ipv6 tcp socket request
backlog when syncookies are not enabled.  When backlog
becomes very deep, last quarter of backlog is limited to
validated destinations.  Previously only ipv4 implemented
this logic, but now ipv6 does too.

Now we are only one step away from enabling timewait
recycling for ipv6, and that step is simply filling in
the implementation of tcp_v6_get_peer() and
tcp_v6_tw_get_peer().

Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-02 12:14:29 -08:00
Eric Dumazet f2cd2d3e9b net sched: use xps information for qdisc NUMA affinity
Allocate qdisc memory according to NUMA properties of cpus included in
xps map.

To be effective, qdisc should be (re)setup after changes
of /sys/class/net/eth<n>/queues/tx-<n>/xps_cpus

I added a numa_node field in struct netdev_queue, containing NUMA node
if all cpus included in xps_cpus share same node, else -1.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-01 12:47:42 -08:00
Eric Dumazet a417786948 xps: add __rcu annotations
Avoid sparse warnings : add __rcu annotations and use
rcu_dereference_protected() where necessary.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29 09:43:13 -08:00
Eric Dumazet b02038a17b xps: NUMA allocations for per cpu data
store_xps_map() allocates maps that are used by single cpu, it makes
sense to use NUMA allocations.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-29 09:43:13 -08:00
Tom Herbert bf26414510 xps: Add CONFIG_XPS
This patch adds XPS_CONFIG option to enable and disable XPS.  This is
done in the same manner as RPS_CONFIG.  This is also fixes build
failure in XPS code when SMP is not enabled.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-28 18:24:14 -08:00
Eric Dumazet 5a0d2268d2 net: add netif_tx_queue_frozen_or_stopped
When testing struct netdev_queue state against FROZEN bit, we also test
XOFF bit. We can test both bits at once and save some cycles.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-28 10:47:18 -08:00
Thomas Graf cf7afbfeb8 rtnl: make link af-specific updates atomic
As David pointed out correctly, updates to af-specific attributes
are currently not atomic. If multiple changes are requested and
one of them fails, previous updates may have been applied already
leaving the link behind in a undefined state.

This patch splits the function parse_link_af() into two functions
validate_link_af() and set_link_at(). validate_link_af() is placed
to validate_linkmsg() check for errors as early as possible before
any changes to the link have been made. set_link_af() is called to
commit the changes later.

This method is not fail proof, while it is currently sufficient
to make set_link_af() inerrable and thus 100% atomic, the
validation function method will not be able to detect all error
scenarios in the future, there will likely always be errors
depending on states which are f.e. not protected by rtnl_mutex
and thus may change between validation and setting.

Also, instead of silently ignoring unknown address families and
config blocks for address families which did not register a set
function the errors EAFNOSUPPORT respectively EOPNOSUPPORT are
returned to avoid comitting 4 out of 5 update requests without
notifying the user.

Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-27 22:56:08 -08:00
Tom Herbert 1d24eb4815 xps: Transmit Packet Steering
This patch implements transmit packet steering (XPS) for multiqueue
devices.  XPS selects a transmit queue during packet transmission based
on configuration.  This is done by mapping the CPU transmitting the
packet to a queue.  This is the transmit side analogue to RPS-- where
RPS is selecting a CPU based on receive queue, XPS selects a queue
based on the CPU (previously there was an XPS patch from Eric
Dumazet, but that might more appropriately be called transmit completion
steering).

Each transmit queue can be associated with a number of CPUs which will
use the queue to send packets.  This is configured as a CPU mask on a
per queue basis in:

/sys/class/net/eth<n>/queues/tx-<n>/xps_cpus

The mappings are stored per device in an inverted data structure that
maps CPUs to queues.  In the netdevice structure this is an array of
num_possible_cpu structures where each structure holds and array of
queue_indexes for queues which that CPU can use.

The benefits of XPS are improved locality in the per queue data
structures.  Also, transmit completions are more likely to be done
nearer to the sending thread, so this should promote locality back
to the socket on free (e.g. UDP).  The benefits of XPS are dependent on
cache hierarchy, application load, and other factors.  XPS would
nominally be configured so that a queue would only be shared by CPUs
which are sharing a cache, the degenerative configuration woud be that
each CPU has it's own queue.

Below are some benchmark results which show the potential benfit of
this patch.  The netperf test has 500 instances of netperf TCP_RR test
with 1 byte req. and resp.

bnx2x on 16 core AMD
   XPS (16 queues, 1 TX queue per CPU)  1234K at 100% CPU
   No XPS (16 queues)                   996K at 100% CPU

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-24 11:44:20 -08:00
Tom Herbert 3853b5841c xps: Improvements in TX queue selection
In dev_pick_tx, don't do work in calculating queue
index or setting
the index in the sock unless the device has more than one queue.  This
allows the sock to be set only with a queue index of a multi-queue
device which is desirable if device are stacked like in a tunnel.

We also allow the mapping of a socket to queue to be changed.  To
maintain in order packet transmission a flag (ooo_okay) has been
added to the sk_buff structure.  If a transport layer sets this flag
on a packet, the transmit queue can be changed for the socket.
Presumably, the transport would set this if there was no possbility
of creating OOO packets (for instance, there are no packets in flight
for the socket).  This patch includes the modification in TCP output
for setting this flag.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-24 11:44:19 -08:00
Eric Dumazet bba14de987 scm: lower SCM_MAX_FD
Lower SCM_MAX_FD from 255 to 253 so that allocations for scm_fp_list are
halved. (commit f8d570a4 added two pointers in this structure)

scm_fp_dup() should not copy whole structure (and trigger kmemcheck
warnings), but only the used part. While we are at it, only allocate
needed size.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-24 11:16:43 -08:00
Eric Dumazet 551eaff1b3 pktgen: allow faster module unload
Unloading pktgen module needs ~6 seconds on a 64 cpus machine, to stop
64 kthreads.

Add a pktgen_exiting variable to let kernel threads die faster, so that
kthread_stop() doesnt have to wait too long for them. This variable is
not tested in fast path.

Note : Before exiting from pktgen_thread_worker(), we must make sure
kthread_stop() is waiting for this thread to be stopped, like its done
in kernel/softirq.c

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-21 10:26:44 -08:00
Eric Dumazet 7a1c8e5ab1 net: allow GFP_HIGHMEM in __vmalloc()
We forgot to use __GFP_HIGHMEM in several __vmalloc() calls.

In ceph, add the missing flag.

In fib_trie.c, xfrm_hash.c and request_sock.c, using vzalloc() is
cleaner and allows using HIGHMEM pages as well.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-21 10:04:04 -08:00
David S. Miller 24912420e9 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/bonding/bond_main.c
	net/core/net-sysfs.c
	net/ipv6/addrconf.c
2010-11-19 13:13:47 -08:00
Eric Dumazet c26aed40f4 filter: use reciprocal divide
At compile time, we can replace the DIV_K instruction (divide by a
constant value) by a reciprocal divide.

At exec time, the expensive divide is replaced by a multiply, a less
expensive operation on most processors.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 10:06:54 -08:00
Eric Dumazet 8c1592d68b filter: cleanup codes[] init
Starting the translated instruction to 1 instead of 0 allows us to
remove one descrement at check time and makes codes[] array init
cleaner.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 10:04:23 -08:00
Eric Dumazet 93aaae2e01 filter: optimize sk_run_filter
Remove pc variable to avoid arithmetic to compute fentry at each filter
instruction. Jumps directly manipulate fentry pointer.

As the last instruction of filter[] is guaranteed to be a RETURN, and
all jumps are before the last instruction, we dont need to check filter
bounds (number of instructions in filter array) at each iteration, so we
remove it from sk_run_filter() params.

On x86_32 remove f_k var introduced in commit 57fe93b374
(filter: make sure filters dont read uninitialized memory)

Note : We could use a CONFIG_ARCH_HAS_{FEW|MANY}_REGISTERS in order to
avoid too many ifdefs in this code.

This helps compiler to use cpu registers to hold fentry and A
accumulator.

On x86_32, this saves 401 bytes, and more important, sk_run_filter()
runs much faster because less register pressure (One less conditional
branch per BPF instruction)

# size net/core/filter.o net/core/filter_pre.o
   text    data     bss     dec     hex filename
   2948       0       0    2948     b84 net/core/filter.o
   3349       0       0    3349     d15 net/core/filter_pre.o

on x86_64 :
# size net/core/filter.o net/core/filter_pre.o
   text    data     bss     dec     hex filename
   5173       0       0    5173    1435 net/core/filter.o
   5224       0       0    5224    1468 net/core/filter_pre.o

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 09:49:59 -08:00
Randy Dunlap 0302b8622c net: fix kernel-doc for sk_filter_rcu_release
Fix kernel-doc warning for sk_filter_rcu_release():

Warning(net/core/filter.c:586): missing initial short description on line:
 * 	sk_filter_rcu_release: Release a socket filter by rcu_head

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc:	"David S. Miller" <davem@davemloft.net>
Cc:	netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-19 09:27:15 -08:00
Changli Gao 4c3710afbc net: move definitions of BPF_S_* to net/core/filter.c
BPF_S_* are used internally, should not be exposed to the others.

Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-18 10:59:51 -08:00
Tetsuo Handa cba328fc5e filter: Optimize instruction revalidation code.
Since repeating u16 value to u8 value conversion using switch() clause's
case statement is wasteful, this patch introduces u16 to u8 mapping table
and removes most of case statements. As a result, the size of net/core/filter.o
is reduced by about 29% on x86.

Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-18 10:58:35 -08:00
John Fastabend 9e50e3ac5a net: add priority field to pktgen
Add option to set skb priority to pktgen. Useful for testing
QOS features. Also by running pktgen on the vlan device the
qdisc on the real device can be tested.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-18 10:43:07 -08:00
John Fastabend 7d8e76bf9a net: zero kobject in rx_queue_release
netif_set_real_num_rx_queues() can decrement and increment
the number of rx queues. For example ixgbe does this as
features and offloads are toggled. Presumably this could
also happen across down/up on most devices if the available
resources changed (cpu offlined).

The kobject needs to be zero'd in this case so that the
state is not preserved across kobject_put()/kobject_init_and_add().

This resolves the following error report.

ixgbe 0000:03:00.0: eth2: NIC Link is Up 10 Gbps, Flow Control: RX/TX
kobject (ffff880324b83210): tried to init an initialized object, something is seriously wrong.
Pid: 1972, comm: lldpad Not tainted 2.6.37-rc18021qaz+ #169
Call Trace:
 [<ffffffff8121c940>] kobject_init+0x3a/0x83
 [<ffffffff8121cf77>] kobject_init_and_add+0x23/0x57
 [<ffffffff8107b800>] ? mark_lock+0x21/0x267
 [<ffffffff813c6d11>] net_rx_queue_update_kobjects+0x63/0xc6
 [<ffffffff813b5e0e>] netif_set_real_num_rx_queues+0x5f/0x78
 [<ffffffffa0261d49>] ixgbe_set_num_queues+0x1c6/0x1ca [ixgbe]
 [<ffffffffa0262509>] ixgbe_init_interrupt_scheme+0x1e/0x79c [ixgbe]
 [<ffffffffa0274596>] ixgbe_dcbnl_set_state+0x167/0x189 [ixgbe]

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-18 09:41:40 -08:00
John Fastabend 9ea19481db net: zero kobject in rx_queue_release
netif_set_real_num_rx_queues() can decrement and increment
the number of rx queues. For example ixgbe does this as
features and offloads are toggled. Presumably this could
also happen across down/up on most devices if the available
resources changed (cpu offlined).

The kobject needs to be zero'd in this case so that the
state is not preserved across kobject_put()/kobject_init_and_add().

This resolves the following error report.

ixgbe 0000:03:00.0: eth2: NIC Link is Up 10 Gbps, Flow Control: RX/TX
kobject (ffff880324b83210): tried to init an initialized object, something is seriously wrong.
Pid: 1972, comm: lldpad Not tainted 2.6.37-rc18021qaz+ #169
Call Trace:
 [<ffffffff8121c940>] kobject_init+0x3a/0x83
 [<ffffffff8121cf77>] kobject_init_and_add+0x23/0x57
 [<ffffffff8107b800>] ? mark_lock+0x21/0x267
 [<ffffffff813c6d11>] net_rx_queue_update_kobjects+0x63/0xc6
 [<ffffffff813b5e0e>] netif_set_real_num_rx_queues+0x5f/0x78
 [<ffffffffa0261d49>] ixgbe_set_num_queues+0x1c6/0x1ca [ixgbe]
 [<ffffffffa0262509>] ixgbe_init_interrupt_scheme+0x1e/0x79c [ixgbe]
 [<ffffffffa0274596>] ixgbe_dcbnl_set_state+0x167/0x189 [ixgbe]

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-17 12:27:46 -08:00
Thomas Graf f8ff182c71 rtnetlink: Link address family API
Each net_device contains address family specific data such as
per device settings and statistics. We already expose this data
via procfs/sysfs and partially netlink.

The netlink method requires the requester to send one RTM_GETLINK
request for each address family it wishes to receive data of
and then merge this data itself.

This patch implements a new API which combines all address family
specific link data in a new netlink attribute IFLA_AF_SPEC.
IFLA_AF_SPEC contains a sequence of nested attributes, one for each
address family which in turn defines the structure of its own
attribute. Example:

   [IFLA_AF_SPEC] = {
       [AF_INET] = {
           [IFLA_INET_CONF] = ...,
       },
       [AF_INET6] = {
           [IFLA_INET6_FLAGS] = ...,
           [IFLA_INET6_CONF] = ...,
       }
   }

The API also allows for address families to implement a function
which parses the IFLA_AF_SPEC attribute sent by userspace to
implement address family specific link options.

Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-17 11:28:24 -08:00
David S. Miller 6b35308850 net: Export netif_get_vlan_features().
ERROR: "netif_get_vlan_features" [drivers/net/xen-netfront.ko] undefined!

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-15 20:15:03 -08:00
Tom Herbert fe8222406c net: Simplify RX queue allocation
This patch move RX queue allocation to alloc_netdev_mq and freeing of
the queues to free_netdev (symmetric to TX queue allocation).  Each
kobject RX queue takes a reference to the queue's device so that the
device can't be freed before all the kobjects have been released-- this
obviates the need for reference counts specific to RX queues.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-15 10:57:28 -08:00
Tom Herbert ed9af2e839 net: Move TX queue allocation to alloc_netdev_mq
TX queues are now allocated in alloc_netdev_mq and freed in
free_netdev.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-15 10:56:54 -08:00
Jesse Gross 58e998c6d2 offloading: Force software GSO for multiple vlan tags.
We currently use vlan_features to check for TSO support if there is
a vlan tag.  However, it's quite likely that the NIC is not able to
do TSO when there is an arbitrary number of tags.  Therefore if there
is more than one tag (in-band or out-of-band), fall back to software
emulation.

Signed-off-by: Jesse Gross <jesse@nicira.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-15 09:22:53 -08:00
Jesse Gross c8d5bcd1af offloading: Support multiple vlan tags in GSO.
We assume that hardware TSO can't support multiple levels of vlan tags
but we allow it to be done.  Therefore, enable GSO to parse these tags
so we can fallback to software.

Signed-off-by: Jesse Gross <jesse@nicira.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-15 09:22:53 -08:00
Jesse Gross e1e78db628 offloading: Make scatter/gather more tolerant of vlans.
When checking if it is necessary to linearize a packet, we currently
use vlan_features if the packet contains either an in-band or out-
of-band vlan tag.  However, in-band tags aren't special in any way
for scatter/gather since they are part of the packet buffer and are
simply more data to DMA.  Therefore, only use vlan_features for out-
of-band tags, which could potentially have some interaction with
scatter/gather.

Signed-off-by: Jesse Gross <jesse@nicira.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-15 09:22:52 -08:00
David S. Miller c25ecd0a21 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2010-11-14 11:57:05 -08:00
Thomas Graf 369cf77a6a rtnetlink: Fix message size calculation for link messages
nlmsg_total_size() calculates the length of a netlink message
including header and alignment. nla_total_size() calculates the
space an individual attribute consumes which was meant to be used
in this context.

Also, ensure to account for the attribute header for the
IFLA_INFO_XSTATS attribute as implementations of get_xstats_size()
seem to assume that we do so.

The addition of two message headers minus the missing attribute
header resulted in a calculated message size that was larger than
required. Therefore we never risked running out of skb tailroom.

Signed-off-by: Thomas Graf <tgraf@infradead.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-12 10:53:09 -08:00
Eric Dumazet 8d987e5c75 net: avoid limits overflow
Robin Holt tried to boot a 16TB machine and found some limits were
reached : sysctl_tcp_mem[2], sysctl_udp_mem[2]

We can switch infrastructure to use long "instead" of "int", now
atomic_long_t primitives are available for free.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Robin Holt <holt@sgi.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-10 12:12:00 -08:00
David S. Miller 57fe93b374 filter: make sure filters dont read uninitialized memory
There is a possibility malicious users can get limited information about
uninitialized stack mem array. Even if sk_run_filter() result is bound
to packet length (0 .. 65535), we could imagine this can be used by
hostile user.

Initializing mem[] array, like Dan Rosenberg suggested in his patch is
expensive since most filters dont even use this array.

Its hard to make the filter validation in sk_chk_filter(), because of
the jumps. This might be done later.

In this patch, I use a bitmap (a single long var) so that only filters
using mem[] loads/stores pay the price of added security checks.

For other filters, additional cost is a single instruction.

[ Since we access fentry->k a lot now, cache it in a local variable
  and mark filter entry pointer as const. -DaveM ]

Reported-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-10 10:38:24 -08:00
Eric Dumazet 332dd96f7a net/dst: dst_dev_event() called after other notifiers
Followup of commit ef885afbf8 (net: use rcu_barrier() in
rollback_registered_many)

dst_dev_event() scans a garbage dst list that might be feeded by various
network notifiers at device dismantle time.

Its important to call dst_dev_event() after other notifiers, or we might
enter the infamous msleep(250) in netdev_wait_allrefs(), and wait one
second before calling again call_netdevice_notifiers(NETDEV_UNREGISTER,
dev) to properly remove last device references.

Use priority -10 to let dst_dev_notifier be called after other network
notifiers (they have the default 0 priority)

Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Octavian Purdila <opurdila@ixiacom.com>
Reported-by: Benjamin LaHaise <bcrl@kvack.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-09 12:17:16 -08:00
Joe Perches b194a3674f net/core/dev.c: Update WARN uses
Coalesce long formats.
Add missing newlines.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-09 09:22:31 -08:00
Junchang Wang eb589063ed pktgen: correct uninitialized queue_map
This fix a bug reported by backyes.
Right the first time pktgen's using queue_map that's not been initialized
by set_cur_queue_map(pkt_dev);

Signed-off-by: Junchang Wang <junchangwang@gmail.com>
Signed-off-by: Backyes <backyes@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-08 12:17:07 -08:00
Dmitry Torokhov 86c2c0a8a4 NET: pktgen - fix compile warning
This should fix the following warning:

net/core/pktgen.c: In function ‘pktgen_if_write’:
net/core/pktgen.c:890: warning: comparison of distinct pointer types lacks a cast

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Reviewed-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-07 05:28:01 -08:00
Tom Herbert df32cc193a net: check queue_index from sock is valid for device
In dev_pick_tx recompute the queue index if the value stored in the
socket is greater than or equal to the number of real queues for the
device.  The saved index in the sock structure is not guaranteed to
be appropriate for the egress device (this could happen on a route
change or in presence of tunnelling).  The result of the queue index
being bad would be to return a bogus queue (crash could prersumably
follow).

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-01 12:55:52 -07:00
Uwe Kleine-König b595076a18 tree-wide: fix comment/printk typos
"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-11-01 15:38:34 -04:00
Nelson Elhage 448d7b5daf pktgen: Limit how much data we copy onto the stack.
A program that accidentally writes too much data to the pktgen file can overflow
the kernel stack and oops the machine. This is only triggerable by root, so
there's no security issue, but it's still an unfortunate bug.

printk() won't print more than 1024 bytes in a single call, anyways, so let's
just never copy more than that much data. We're on a fairly shallow stack, so
that should be safe even with CONFIG_4KSTACKS.

Signed-off-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-28 11:47:53 -07:00
David S. Miller 8acfe468b0 net: Limit socket I/O iovec total length to INT_MAX.
This helps protect us from overflow issues down in the
individual protocol sendmsg/recvmsg handlers.  Once
we hit INT_MAX we truncate out the rest of the iovec
by setting the iov_len members to zero.

This works because:

1) For SOCK_STREAM and SOCK_SEQPACKET sockets, partial
   writes are allowed and the application will just continue
   with another write to send the rest of the data.

2) For datagram oriented sockets, where there must be a
   one-to-one correspondance between write() calls and
   packets on the wire, INT_MAX is going to be far larger
   than the packet size limit the protocol is going to
   check for and signal with -EMSGSIZE.

Based upon a patch by Linus Torvalds.

Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-28 11:47:52 -07:00
Eric Dumazet 7a2b03c517 fib_rules: __rcu annotates ctarget
Adds __rcu annotation to (struct fib_rule)->ctarget

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-27 11:37:32 -07:00
Ben Hutchings 66c68bcc48 net: NETIF_F_HW_CSUM does not imply FCoE CRC offload
NETIF_F_HW_CSUM indicates the ability to update an TCP/IP-style 16-bit
checksum with the checksum of an arbitrary part of the packet data,
whereas the FCoE CRC is something entirely different.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org [2.6.32+]
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-27 11:37:29 -07:00
Ben Hutchings af1905dbec net: Fix some corner cases in dev_can_checksum()
dev_can_checksum() incorrectly returns true in these cases:

1. The skb has both out-of-band and in-band VLAN tags and the device
   supports checksum offload for the encapsulated protocol but only with
   one layer of encapsulation.
2. The skb has a VLAN tag and the device supports generic checksumming
   but not in conjunction with VLAN encapsulation.

Rearrange the VLAN tag checks to avoid these.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-27 11:37:29 -07:00
Eric Dumazet ebb9fed2de fib: fix fib_nl_newrule()
Some panic reports in fib_rules_lookup() show a rule could have a NULL
pointer as a next pointer in the rules_list.

This can actually happen because of a bug in fib_nl_newrule() : It
checks if current rule is the destination of unresolved gotos. (Other
rules have gotos to this about to be inserted rule)

Problem is it does the resolution of the gotos before the rule is
inserted in the rules_list (and has a valid next pointer)

Fix this by moving the rules_list insertion before the changes on gotos.

A lockless reader can not any more follow a ctarget pointer, unless
destination is ready (has a valid next pointer)

Reported-by: Oleg A. Arkhangelsky <sysoleg@yandex.ru>
Reported-by: Joe Buehler <aspam@cox.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-26 11:42:38 -07:00
Eric Dumazet 0d7da9ddd9 net: add __rcu annotation to sk_filter
Add __rcu annotation to :
        (struct sock)->sk_filter

And use appropriate rcu primitives to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-25 14:18:28 -07:00
Eric Dumazet 1c87733d06 net_ns: add __rcu annotations
add __rcu annotation to (struct net)->gen, and use
rcu_dereference_protected() in net_assign_generic()

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-25 14:18:27 -07:00
Eric Dumazet 6e3f7faf3e rps: add __rcu annotations
Add __rcu annotations to :
	(struct netdev_rx_queue)->rps_map
	(struct netdev_rx_queue)->rps_flow_table
	struct rps_sock_flow_table *rps_sock_flow_table;

And use appropriate rcu primitives.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-25 14:18:27 -07:00
Eric Dumazet 198caeca3e ipv6: ip6_ptr rcu annotations
(struct net_device)->ip6_ptr is rcu protected :

add __rcu annotation and proper rcu primitives.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-25 13:09:43 -07:00
David S. Miller 11a766ce91 net: Increase xmit RECURSION_LIMIT to 10.
Three is definitely too low, and we know from reports that GRE tunnels
stacked as deeply as 37 levels cause stack overflows, so pick some
reasonable value between those two.

Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-25 12:51:55 -07:00
Paul Gortmaker d618222352 pktgen: clean up handling of local/transient counter vars
The temporary variable "i" is needlessly initialized to zero
in two distinct cases in this file:

1) where it is set to zero and then used as an argument in an addition
before being assigned a non-zero value.

2) where it is only used in a standard/typical loop counter

For (1), simply delete assignment to zero and usages while still
zero; for (2) simply make the loop start at zero as per standard
practice as seen everywhere else in the same file.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-24 15:23:35 -07:00
Linus Torvalds 5f05647dd8 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
  bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
  vlan: Calling vlan_hwaccel_do_receive() is always valid.
  tproxy: use the interface primary IP address as a default value for --on-ip
  tproxy: added IPv6 support to the socket match
  cxgb3: function namespace cleanup
  tproxy: added IPv6 support to the TPROXY target
  tproxy: added IPv6 socket lookup function to nf_tproxy_core
  be2net: Changes to use only priority codes allowed by f/w
  tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
  tproxy: added tproxy sockopt interface in the IPV6 layer
  tproxy: added udp6_lib_lookup function
  tproxy: added const specifiers to udp lookup functions
  tproxy: split off ipv6 defragmentation to a separate module
  l2tp: small cleanup
  nf_nat: restrict ICMP translation for embedded header
  can: mcp251x: fix generation of error frames
  can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
  can-raw: add msg_flags to distinguish local traffic
  9p: client code cleanup
  rds: make local functions/variables static
  ...

Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
2010-10-23 11:47:02 -07:00
Linus Torvalds 5d70f79b5e Merge branch 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (163 commits)
  tracing: Fix compile issue for trace_sched_wakeup.c
  [S390] hardirq: remove pointless header file includes
  [IA64] Move local_softirq_pending() definition
  perf, powerpc: Fix power_pmu_event_init to not use event->ctx
  ftrace: Remove recursion between recordmcount and scripts/mod/empty
  jump_label: Add COND_STMT(), reducer wrappery
  perf: Optimize sw events
  perf: Use jump_labels to optimize the scheduler hooks
  jump_label: Add atomic_t interface
  jump_label: Use more consistent naming
  perf, hw_breakpoint: Fix crash in hw_breakpoint creation
  perf: Find task before event alloc
  perf: Fix task refcount bugs
  perf: Fix group moving
  irq_work: Add generic hardirq context callbacks
  perf_events: Fix transaction recovery in group_sched_in()
  perf_events: Fix bogus AMD64 generic TLB events
  perf_events: Fix bogus context time tracking
  tracing: Remove parent recording in latency tracer graph options
  tracing: Use one prologue for the preempt irqs off tracer function tracers
  ...
2010-10-21 12:54:49 -07:00
Linus Torvalds 888a6f77e0 Merge branch 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (52 commits)
  sched: fix RCU lockdep splat from task_group()
  rcu: using ACCESS_ONCE() to observe the jiffies_stall/rnp->qsmask value
  sched: suppress RCU lockdep splat in task_fork_fair
  net: suppress RCU lockdep false positive in sock_update_classid
  rcu: move check from rcu_dereference_bh to rcu_read_lock_bh_held
  rcu: Add advice to PROVE_RCU_REPEATEDLY kernel config parameter
  rcu: Add tracing data to support queueing models
  rcu: fix sparse errors in rcutorture.c
  rcu: only one evaluation of arg in rcu_dereference_check() unless sparse
  kernel: Remove undead ifdef CONFIG_DEBUG_LOCK_ALLOC
  rcu: fix _oddness handling of verbose stall warnings
  rcu: performance fixes to TINY_PREEMPT_RCU callback checking
  rcu: upgrade stallwarn.txt documentation for CPU-bound RT processes
  vhost: add __rcu annotations
  rcu: add comment stating that list_empty() applies to RCU-protected lists
  rcu: apply TINY_PREEMPT_RCU read-side speedup to TREE_PREEMPT_RCU
  rcu: combine duplicate code, courtesy of CONFIG_PREEMPT_RCU
  rcu: Upgrade srcu_read_lock() docbook about SRCU grace periods
  rcu: document ways of stalling updates in low-memory situations
  rcu: repair code-duplication FIXMEs
  ...
2010-10-21 12:54:12 -07:00
David S. Miller 2198a10b50 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/core/dev.c
2010-10-21 08:43:05 -07:00
stephen hemminger d0c2b0d265 napi: unexport napi_reuse_skb
The function napi_reuse_skb is only used inside core.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 04:26:38 -07:00
Tejun Heo a5c30b349b net/neighbour: cancel_delayed_work() + flush_scheduled_work() -> cancel_delayed_work_sync()
flush_scheduled_work() is going away.  Prepare for it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 04:25:48 -07:00
Ben Greear d2ed817766 net/core: Allow tagged VLAN packets to flow through VETH devices.
When there are VLANs on a VETH device, the packets being transmitted
through the VETH device may be 4 bytes bigger than MTU.  A check
in dev_forward_skb did not take this into account and so dropped
these packets.

This patch is needed at least as far back as 2.6.34.7 and should
be considered for -stable.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 04:06:29 -07:00
stephen hemminger 8d8a0b1cc2 rtnetlink: remove rtnl_kill_links
The function rtnl_kill_links is defined but never used.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 03:09:45 -07:00
Jesse Gross d5dbda2380 ethtool: Add support for vlan accleration.
Now that vlan acceleration is handled consistently regardless of usage,
it is possible to enable and disable it at will.  This adds support for
Ethtool operations that change the offloading status for debugging
purposes, similar to other forms of hardware acceleration.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 01:26:54 -07:00
Jesse Gross 3701e51382 vlan: Centralize handling of hardware acceleration.
Currently each driver that is capable of vlan hardware acceleration
must be aware of the vlan groups that are configured and then pass
the stripped tag to a specialized receive function.  This is

different from other types of hardware offload in that it places a
significant amount of knowledge in the driver itself rather keeping
it in the networking core.

This makes vlan offloading function more similarly to other forms
of offloading (such as checksum offloading or TSO) by doing the
following:
* On receive, stripped vlans are passed directly to the network
core, without attempting to check for vlan groups or reconstructing
the header if no group
* vlans are made less special by folding the logic into the main
receive routines
* On transmit, the device layer will add the vlan header in software
if the hardware doesn't support it, instead of spreading that logic
out in upper layers, such as bonding.

There are a number of advantages to this:
* Fixes all bugs with drivers incorrectly dropping vlan headers at once.
* Avoids having to disable VLAN acceleration when in promiscuous mode
(good for bridging since it always puts devices in promiscuous mode).
* Keeps VLAN tag separate until given to ultimate consumer, which
avoids needing to do header reconstruction as in tg3 unless absolutely
necessary.
* Consolidates common code in core networking.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 01:26:53 -07:00
Jesse Gross 7b9c609037 vlan: Enable software emulation for vlan accleration.
Currently users of hardware vlan accleration need to know whether
the device supports it before generating packets.  However, vlan
acceleration will soon be available in a more flexible manner so
knowing ahead of time becomes much more difficult.  This adds
a software fallback path for vlan packets on devices without the
necessary offloading support, similar to other types of hardware
accleration.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-21 01:26:52 -07:00
Eric Dumazet 27b75c95f1 net: avoid RCU for NOCACHE dst
There is no point using RCU for dst we allocate for a very short time
(used once).

Change dst_release() to take DST_NOCACHE into account, but also change
skb_dst_set_noref() to force a refcount increment for such dst.

This is a _huge_ gain, because we dont waste memory to store xx thousand
of dsts. Instead of queueing them to RCU, we can free them instantly.

CPU caches can stay hot, re-using same memory blocks to hold temporary
dsts.

Note : remove unneeded smp_mb__before_atomic_dec(); in dst_release(),
since atomic_dec_return() implies a full memory barrier.

Stress test, 160.000.000 udp frames sent, IP route cache disabled
(DDOS).

Before:

real    0m38.091s
user    0m13.189s
sys     7m53.018s

After:

real	0m29.946s
user	0m12.157s
sys	7m40.605s

For reference, if IP route cache was enabled :

real	0m32.030s
user	0m10.521s
sys	8m15.243s

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-20 03:02:23 -07:00
Tom Herbert e6484930d7 net: allocate tx queues in register_netdevice
This patch introduces netif_alloc_netdev_queues which is called from
register_device instead of alloc_netdev_mq.  This makes TX queue
allocation symmetric with RX allocation.  Also, queue locks allocation
is done in netdev_init_one_queue.  Change set_real_num_tx_queues to
fail if requested number < 1 or greater than number of allocated
queues.

Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-20 02:27:59 -07:00
Tom Herbert bd25fa7ba5 net: cleanups in RX queue allocation
Clean up in RX queue allocation.  In netif_set_real_num_rx_queues
return error on attempt to set zero queues, or requested number is
greater than number of allocated queues.  In netif_alloc_rx_queues,
do BUG_ON if queue_count is zero.

Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-20 02:27:59 -07:00
Tom Herbert 55513fb428 net: fail alloc_netdev_mq if queue count < 1
In alloc_netdev_mq fail if requested queue_count < 1.

Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-20 02:27:58 -07:00
Neil Horman f13d493d9c netpoll: Revert napi_poll fix for bonding driver
In an erlier patch I modified napi_poll so that devices with IFF_MASTER polled
the per_cpu list instead of the device list for napi.  I did this because the
bonding driver has no napi instances to poll, it instead expects to check the
slave devices napi instances, which napi_poll was unaware of.  Looking at this
more closely however, I now see this isn't strictly needed.  As the bond driver
poll_controller calls the slaves poll_controller via netpoll_poll_dev, which
recursively calls poll_napi on each slave, allowing those napi instances to get
serviced.  The earlier patch isn't at all harmfull, its just not needed, so lets
revert it to make the code cleaner.  Sorry for the noise,

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-20 01:44:30 -07:00
Neil Horman 990c3d6f9c bonding: Fix napi poll for bonding driver
Usually the netpoll path, when preforming a napi poll can get away with just
polling all the napi instances of the configured device.  Thats not the case for
the bonding driver however, as the napi instances which may wind up getting
flagged as needing polling after the poll_controller call don't belong to the
bonded device, but rather to the slave devices.  Fix this by checking the device
in question for the IFF_MASTER flag, if set, we know we need to check the full
poll list for this cpu, rather than just the devices napi instance list.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-18 08:32:08 -07:00
Neil Horman c2355e1ab9 bonding: Fix bonding drivers improper modification of netpoll structure
The bonding driver currently modifies the netpoll structure in its xmit path
while sending frames from netpoll.  This is racy, as other cpus can access the
netpoll structure in parallel. Since the bonding driver points np->dev to a
slave device, other cpus can inadvertently attempt to send data directly to
slave devices, leading to improper locking with the bonding master, lost frames,
and deadlocks.  This patch fixes that up.

This patch also removes the real_dev pointer from the netpoll structure as that
data is really only used by bonding in the poll_controller, and we can emulate
its behavior by check each slave for IS_UP.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-18 08:32:07 -07:00
Eric Dumazet a0a4a85a15 fib: remove a useless synchronize_rcu() call
fib_nl_delrule() calls synchronize_rcu() for no apparent reason,
while rtnl is held.

I suspect it was done to avoid an atomic_inc_not_zero() in
fib_rules_lookup(), which commit 7fa7cb7109 added anyway.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16 11:13:22 -07:00
Eric Dumazet 564824b0c5 net: allocate skbs on local node
commit b30973f877 (node-aware skb allocation) spread a wrong habit of
allocating net drivers skbs on a given memory node : The one closest to
the NIC hardware. This is wrong because as soon as we try to scale
network stack, we need to use many cpus to handle traffic and hit
slub/slab management on cross-node allocations/frees when these cpus
have to alloc/free skbs bound to a central node.

skb allocated in RX path are ephemeral, they have a very short
lifetime : Extra cost to maintain NUMA affinity is too expensive. What
appeared as a nice idea four years ago is in fact a bad one.

In 2010, NIC hardwares are multiqueue, or we use RPS to spread the load,
and two 10Gb NIC might deliver more than 28 million packets per second,
needing all the available cpus.

Cost of cross-node handling in network and vm stacks outperforms the
small benefit hardware had when doing its DMA transfert in its 'local'
memory node at RX time. Even trying to differentiate the two allocations
done for one skb (the sk_buff on local node, the data part on NIC
hardware node) is not enough to bring good performance.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-16 11:13:19 -07:00
Eric Dumazet 29b4433d99 net: percpu net_device refcount
We tried very hard to remove all possible dev_hold()/dev_put() pairs in
network stack, using RCU conversions.

There is still an unavoidable device refcount change for every dst we
create/destroy, and this can slow down some workloads (routers or some
app servers, mmap af_packet)

We can switch to a percpu refcount implementation, now dynamic per_cpu
infrastructure is mature. On a 64 cpus machine, this consumes 256 bytes
per device.

On x86, dev_hold(dev) code :

before
        lock    incl 0x280(%ebx)
after:
        movl    0x260(%ebx),%eax
        incl    fs:(%eax)

Stress bench :

(Sending 160.000.000 UDP frames,
IP route cache disabled, dual E5540 @2.53GHz,
32bit kernel, FIB_TRIE)

Before:

real    1m1.662s
user    0m14.373s
sys     12m55.960s

After:

real    0m51.179s
user    0m15.329s
sys     10m15.942s

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-12 12:35:25 -07:00
Eric Dumazet fc66f95c68 net dst: use a percpu_counter to track entries
struct dst_ops tracks number of allocated dst in an atomic_t field,
subject to high cache line contention in stress workload.

Switch to a percpu_counter, to reduce number of time we need to dirty a
central location. Place it on a separate cache line to avoid dirtying
read only fields.

Stress test :

(Sending 160.000.000 UDP frames,
IP route cache disabled, dual E5540 @2.53GHz,
32bit kernel, FIB_TRIE, SLUB/NUMA)

Before:

real    0m51.179s
user    0m15.329s
sys     10m15.942s

After:

real	0m45.570s
user	0m15.525s
sys	9m56.669s

With a small reordering of struct neighbour fields, subject of a
following patch, (to separate refcnt from other read mostly fields)

real	0m41.841s
user	0m15.261s
sys	8m45.949s

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-11 13:06:53 -07:00
Eric Dumazet 0ed8ddf404 neigh: Protect neigh->ha[] with a seqlock
Add a seqlock in struct neighbour to protect neigh->ha[], and avoid
dirtying neighbour in stress situation (many different flows / dsts)

Dirtying takes place because of read_lock(&n->lock) and n->used writes.

Switching to a seqlock, and writing n->used only on jiffies changes
permits less dirtying.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-11 12:54:04 -07:00
David S. Miller d122179a3c Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/core/ethtool.c
2010-10-11 12:30:34 -07:00
Kees Cook b00916b189 net: clear heap allocations for privileged ethtool actions
Several other ethtool functions leave heap uncleared (potentially) by
drivers. Some interfaces appear safe (eeprom, etc), in that the sizes
are well controlled. In some situations (e.g. unchecked error conditions),
the heap will remain unchanged in areas before copying back to userspace.
Note that these are less of an issue since these all require CAP_NET_ADMIN.

Cc: stable@kernel.org
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-11 12:23:25 -07:00
Eric Dumazet 34d101dd62 neigh: speedup neigh_hh_init()
When a new dst is used to send a frame, neigh_resolve_output() tries to
associate an struct hh_cache to this dst, calling neigh_hh_init() with
the neigh rwlock write locked.

Most of the time, hh_cache is already known and linked into neighbour,
so we find it and increment its refcount.

This patch changes the logic so that we call neigh_hh_init() with
neighbour lock read locked only, so that fast path can be run in
parallel by concurrent cpus.

This brings part of the speedup we got with commit c7d4426a98
(introduce DST_NOCACHE flag) for non cached dsts, even for cached ones,
removing one of the contention point that routers hit on multiqueue
enabled machines.

Further improvements would need to use a seqlock instead of an rwlock to
protect neigh->ha[], to not dirty neigh too often and remove two atomic
ops.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-11 09:16:57 -07:00
Tom Herbert 4315d834c1 net: Fix rxq ref counting
The rx->count reference is used to track reference counts to the
number of rx-queue kobjects created for the device.  This patch
eliminates initialization of the counter in netif_alloc_rx_queues
and instead increments the counter each time a kobject is created.
This is now symmetric with the decrement that is done when an object is
released.

Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-08 14:34:32 -07:00
Kees Cook ae6df5f96a net: clear heap allocation for ETHTOOL_GRXCLSRLALL
Calling ETHTOOL_GRXCLSRLALL with a large rule_cnt will allocate kernel
heap without clearing it. For the one driver (niu) that implements it,
it will leave the unused portion of heap unchanged and copy the full
contents back to userspace.

Signed-off-by: Kees Cook <kees.cook@canonical.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-08 10:48:28 -07:00
Ben Hutchings 4e7f79511e net: Update kernel-doc for netif_set_real_num_rx_queues()
Synchronise the comment with the preceding implementation change.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-08 10:33:39 -07:00
Ingo Molnar 7cd2541cf2 Merge commit 'v2.6.36-rc7' into perf/core
Conflicts:
	arch/x86/kernel/module.c

Merge reason: Resolve the conflict, pick up fixes.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-10-08 10:46:27 +02:00
Paul E. McKenney 1144182a87 net: suppress RCU lockdep false positive in sock_update_classid
> ===================================================
> [ INFO: suspicious rcu_dereference_check() usage. ]
> ---------------------------------------------------
> include/linux/cgroup.h:542 invoked rcu_dereference_check() without protection!
>
> other info that might help us debug this:
>
>
> rcu_scheduler_active = 1, debug_locks = 0
> 1 lock held by swapper/1:
>  #0:  (net_mutex){+.+.+.}, at: [<ffffffff813e9010>]
> register_pernet_subsys+0x1f/0x47
>
> stack backtrace:
> Pid: 1, comm: swapper Not tainted 2.6.35.4-28.fc14.x86_64 #1
> Call Trace:
>  [<ffffffff8107bd3a>] lockdep_rcu_dereference+0xaa/0xb3
>  [<ffffffff813e04b9>] sock_update_classid+0x7c/0xa2
>  [<ffffffff813e054a>] sk_alloc+0x6b/0x77
>  [<ffffffff8140b281>] __netlink_create+0x37/0xab
>  [<ffffffff813f941c>] ? rtnetlink_rcv+0x0/0x2d
>  [<ffffffff8140cee1>] netlink_kernel_create+0x74/0x19d
>  [<ffffffff8149c3ca>] ? __mutex_lock_common+0x339/0x35b
>  [<ffffffff813f7e9c>] rtnetlink_net_init+0x2e/0x48
>  [<ffffffff813e8d7a>] ops_init+0xe9/0xff
>  [<ffffffff813e8f0d>] register_pernet_operations+0xab/0x130
>  [<ffffffff813e901f>] register_pernet_subsys+0x2e/0x47
>  [<ffffffff81db7bca>] rtnetlink_init+0x53/0x102
>  [<ffffffff81db835c>] netlink_proto_init+0x126/0x143
>  [<ffffffff81db8236>] ? netlink_proto_init+0x0/0x143
>  [<ffffffff810021b8>] do_one_initcall+0x72/0x186
>  [<ffffffff81d78ebc>] kernel_init+0x23b/0x2c9
>  [<ffffffff8100aae4>] kernel_thread_helper+0x4/0x10
>  [<ffffffff8149e2d0>] ? restore_args+0x0/0x30
>  [<ffffffff81d78c81>] ? kernel_init+0x0/0x2c9
>  [<ffffffff8100aae0>] ? kernel_thread_helper+0x0/0x10

The sock_update_classid() function calls task_cls_classid(current),
but the calling task cannot go away, so there is no danger of
the associated structures disappearing.  Insert an RCU read-side
critical section to suppress the false positive.

Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
2010-10-07 10:02:28 -07:00
John Fastabend 3d3211ef5c net: netif_set_real_num_rx_queues may cap num_rx_queues at init time
Do not set num_rx_queues in netif_set_real_num_rx_queues() some
drivers will increase the real_num_rx_queues later due to a feature
changes or available interrupts increasing. By setting num_rx_queues
here this ends up creating a cap on the number of rx queues
available.

For example the ixgbe driver sets the max number of queues it intends
to use ever then sets the current number in use with the
netif_set_num_{rx|tx}_queues calls. With the current implementation
the number of rx queues gets limited so when a feature such as DCB
or FCoE is enabled the queues are no longer available.

kobjects will only be allocated for real_num_rx_queues so the waste
in memory is minimal.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06 23:35:15 -07:00
Eric Dumazet 767e97e1e0 neigh: RCU conversion of struct neighbour
This is the second step for neighbour RCU conversion.

(first was commit d6bf7817 : RCU conversion of neigh hash table)

neigh_lookup() becomes lockless, but still take a reference on found
neighbour. (no more read_lock()/read_unlock() on tbl->lock)

struct neighbour gets an additional rcu_head field and is freed after an
RCU grace period.

Future work would need to eventually not take a reference on neighbour
for temporary dst (DST_NOCACHE), but this would need dst->_neighbour to
use a noref bit like we did for skb->_dst.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-06 18:01:33 -07:00
Eric Dumazet ebc0ffae5d fib: RCU conversion of fib_lookup()
fib_lookup() converted to be called in RCU protected context, no
reference taken and released on a contended cache line (fib_clntref)

fib_table_lookup() and fib_semantic_match() get an additional parameter.

struct fib_info gets an rcu_head field, and is freed after an rcu grace
period.

Stress test :
(Sending 160.000.000 UDP frames on same neighbour,
IP route cache disabled, dual E5540 @2.53GHz,
32bit kernel, FIB_HASH) (about same results for FIB_TRIE)

Before patch :

real	1m31.199s
user	0m13.761s
sys	23m24.780s

After patch:

real	1m5.375s
user	0m14.997s
sys	15m50.115s

Before patch Profile :

13044.00 15.4% __ip_route_output_key vmlinux
 8438.00 10.0% dst_destroy           vmlinux
 5983.00  7.1% fib_semantic_match    vmlinux
 5410.00  6.4% fib_rules_lookup      vmlinux
 4803.00  5.7% neigh_lookup          vmlinux
 4420.00  5.2% _raw_spin_lock        vmlinux
 3883.00  4.6% rt_set_nexthop        vmlinux
 3261.00  3.9% _raw_read_lock        vmlinux
 2794.00  3.3% fib_table_lookup      vmlinux
 2374.00  2.8% neigh_resolve_output  vmlinux
 2153.00  2.5% dst_alloc             vmlinux
 1502.00  1.8% _raw_read_lock_bh     vmlinux
 1484.00  1.8% kmem_cache_alloc      vmlinux
 1407.00  1.7% eth_header            vmlinux
 1406.00  1.7% ipv4_dst_destroy      vmlinux
 1298.00  1.5% __copy_from_user_ll   vmlinux
 1174.00  1.4% dev_queue_xmit        vmlinux
 1000.00  1.2% ip_output             vmlinux

After patch Profile :

13712.00 15.8% dst_destroy             vmlinux
 8548.00  9.9% __ip_route_output_key   vmlinux
 7017.00  8.1% neigh_lookup            vmlinux
 4554.00  5.3% fib_semantic_match      vmlinux
 4067.00  4.7% _raw_read_lock          vmlinux
 3491.00  4.0% dst_alloc               vmlinux
 3186.00  3.7% neigh_resolve_output    vmlinux
 3103.00  3.6% fib_table_lookup        vmlinux
 2098.00  2.4% _raw_read_lock_bh       vmlinux
 2081.00  2.4% kmem_cache_alloc        vmlinux
 2013.00  2.3% _raw_spin_lock          vmlinux
 1763.00  2.0% __copy_from_user_ll     vmlinux
 1763.00  2.0% ip_output               vmlinux
 1761.00  2.0% ipv4_dst_destroy        vmlinux
 1631.00  1.9% eth_header              vmlinux
 1440.00  1.7% _raw_read_unlock_bh     vmlinux

Reference results, if IP route cache is enabled :

real	0m29.718s
user	0m10.845s
sys	7m37.341s

25213.00 29.5% __ip_route_output_key   vmlinux
 9011.00 10.5% dst_release             vmlinux
 4817.00  5.6% ip_push_pending_frames  vmlinux
 4232.00  5.0% ip_finish_output        vmlinux
 3940.00  4.6% udp_sendmsg             vmlinux
 3730.00  4.4% __copy_from_user_ll     vmlinux
 3716.00  4.4% ip_route_output_flow    vmlinux
 2451.00  2.9% __xfrm_lookup           vmlinux
 2221.00  2.6% ip_append_data          vmlinux
 1718.00  2.0% _raw_spin_lock_bh       vmlinux
 1655.00  1.9% __alloc_skb             vmlinux
 1572.00  1.8% sock_wfree              vmlinux
 1345.00  1.6% kfree                   vmlinux

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-05 20:39:38 -07:00
Eric Dumazet d6bf781712 net neigh: RCU conversion of neigh hash table
David

This is the first step for RCU conversion of neigh code.

Next patches will convert hash_buckets[] and "struct neighbour" to RCU
protected objects.

Thanks

[PATCH net-next] net neigh: RCU conversion of neigh hash table

Instead of storing hash_buckets, hash_mask and hash_rnd in "struct
neigh_table", a new structure is defined :

struct neigh_hash_table {
       struct neighbour        **hash_buckets;
       unsigned int            hash_mask;
       __u32                   hash_rnd;
       struct rcu_head         rcu;
};

And "struct neigh_table" has an RCU protected pointer to such a
neigh_hash_table.

This means the signature of (*hash)() function changed: We need to add a
third parameter with the actual hash_rnd value, since this is not
anymore a neigh_table field.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-05 14:54:36 -07:00
Eric Dumazet 110b249937 net neigh: neigh_delete() and neigh_add() changes
neigh_delete() and neigh_add() dont need to touch device refcount,
we hold RTNL when calling them, so device cannot disappear under us.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-05 14:54:35 -07:00
Eric Dumazet caf586e5f2 net: add a core netdev->rx_dropped counter
In various situations, a device provides a packet to our stack and we
drop it before it enters protocol stack :
- softnet backlog full (accounted in /proc/net/softnet_stat)
- bad vlan tag (not accounted)
- unknown/unregistered protocol (not accounted)

We can handle a per-device counter of such dropped frames at core level,
and automatically adds it to the device provided stats (rx_dropped), so
that standard tools can be used (ifconfig, ip link, cat /proc/net/dev)

This is a generalization of commit 8990f468a (net: rx_dropped
accounting), thus reverting it.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-05 14:47:55 -07:00
stephen hemminger 1df9916e46 fib: fib_rules_cleanup can be static
fib_rules_cleanup_ups is only defined and used in one place.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-05 00:47:39 -07:00
Eric Dumazet 24824a09e3 net: dynamic ingress_queue allocation
ingress being not used very much, and net_device->ingress_queue being
quite a big object (128 or 256 bytes), use a dynamic allocation if
needed (tc qdisc add dev eth0 ingress ...)

dev_ingress_queue(dev) helper should be used only with RTNL taken.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-05 00:23:44 -07:00
David S. Miller 21a180cda0 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	net/ipv4/Kconfig
	net/ipv4/tcp_timer.c
2010-10-04 11:56:38 -07:00
Eric Dumazet c7d4426a98 net: introduce DST_NOCACHE flag
While doing stress tests with IP route cache disabled, and multi queue
devices, I noticed a very high contention on one rwlock used in
neighbour code.

When many cpus are trying to send frames (possibly using a high
performance multiqueue device) to the same neighbour, they fight for the
neigh->lock rwlock in order to call neigh_hh_init(), and fight on
hh->hh_refcnt (a pair of atomic_inc/atomic_dec_and_test())

But we dont need to call neigh_hh_init() for dst that are used only
once. It costs four atomic operations at least, on two contended cache
lines, plus the high contention on neigh->lock rwlock.

Introduce a new dst flag, DST_NOCACHE, that is set when dst was not
inserted in route cache.

With the stress test bench, sending 160000000 frames on one neighbour,
results are :

Before patch:

real	2m28.406s
user	0m11.781s
sys	36m17.964s


After patch:

real	1m26.532s
user	0m12.185s
sys	20m3.903s

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-03 22:17:54 -07:00
Nagendra Tomar 482964e56e net: Fix the condition passed to sk_wait_event()
This patch fixes the condition (3rd arg) passed to sk_wait_event() in
sk_stream_wait_memory(). The incorrect check in sk_stream_wait_memory()
causes the following soft lockup in tcp_sendmsg() when the global tcp
memory pool has exhausted.

>>> snip <<<

localhost kernel: BUG: soft lockup - CPU#3 stuck for 11s! [sshd:6429]
localhost kernel: CPU 3:
localhost kernel: RIP: 0010:[sk_stream_wait_memory+0xcd/0x200]  [sk_stream_wait_memory+0xcd/0x200] sk_stream_wait_memory+0xcd/0x200
localhost kernel:
localhost kernel: Call Trace:
localhost kernel:  [sk_stream_wait_memory+0x1b1/0x200] sk_stream_wait_memory+0x1b1/0x200
localhost kernel:  [<ffffffff802557c0>] autoremove_wake_function+0x0/0x40
localhost kernel:  [ipv6:tcp_sendmsg+0x6e6/0xe90] tcp_sendmsg+0x6e6/0xce0
localhost kernel:  [sock_aio_write+0x126/0x140] sock_aio_write+0x126/0x140
localhost kernel:  [xfs:do_sync_write+0xf1/0x130] do_sync_write+0xf1/0x130
localhost kernel:  [<ffffffff802557c0>] autoremove_wake_function+0x0/0x40
localhost kernel:  [hrtimer_start+0xe3/0x170] hrtimer_start+0xe3/0x170
localhost kernel:  [vfs_write+0x185/0x190] vfs_write+0x185/0x190
localhost kernel:  [sys_write+0x50/0x90] sys_write+0x50/0x90
localhost kernel:  [system_call+0x7e/0x83] system_call+0x7e/0x83

>>> snip <<<

What is happening is, that the sk_wait_event() condition passed from
sk_stream_wait_memory() evaluates to true for the case of tcp global memory
exhaustion. This is because both sk_stream_memory_free() and vm_wait are true
which causes sk_wait_event() to *not* call schedule_timeout().
Hence sk_stream_wait_memory() returns immediately to the caller w/o sleeping.
This causes the caller to again try allocation, which again fails and again
calls sk_stream_wait_memory(), and so on.

[ Bug introduced by commit c1cbe4b7ad
  ("[NET]: Avoid atomic xchg() for non-error case") -DaveM ]

Signed-off-by: Nagendra Singh Tomar <tomer_iisc@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-03 20:41:32 -07:00
Eric Dumazet bfa5ae63b8 net: rename netdev rx_queue to ingress_queue
There is some confusion with rx_queue name after RPS, and net drivers
private rx_queue fields.

I suggest to rename "struct net_device"->rx_queue to ingress_queue.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-29 13:25:53 -07:00
Eric Dumazet 745e20f1b6 net: add a recursion limit in xmit path
As tunnel devices are going to be lockless, we need to make sure a
misconfigured machine wont enter an infinite loop.

Add a percpu variable, and limit to three the number of stacked xmits.

Reported-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-29 13:23:09 -07:00
Tom Herbert 4465b46900 ipv4: Allow configuring subnets as local addresses
This patch allows a host to be configured to respond to any address in
a specified range as if it were local, without actually needing to
configure the address on an interface.  This is done through routing
table configuration.  For instance, to configure a host to respond
to any address in 10.1/16 received on eth0 as a local address we can do:

ip rule add from all iif eth0 lookup 200
ip route add local 10.1/16 dev lo proto kernel scope host src 127.0.0.1 table 200

This host is now reachable by any 10.1/16 address (route lookup on
input for packets received on eth0 can find the route).  On output, the
rule will not be matched so that this host can still send packets to
10.1/16 (not sent on loopback).  Presumably, external routing can be
configured to make sense out of this.

To make this work, we needed to modify the logic in finding the
interface which is assigned a given source address for output
(dev_ip_find).  We perform a normal fib_lookup instead of just a
lookup on the local table, and in the lookup we ignore the input
interface for matching.

This patch is useful to implement IP-anycast for subnets of virtual
addresses.

Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-28 23:38:15 -07:00
Ben Hutchings 62fe0b40ab net: Allow changing number of RX queues after device allocation
For RPS, we create a kobject for each RX queue based on the number of
queues passed to alloc_netdev_mq().  However, drivers generally do not
determine the numbers of hardware queues to use until much later, so
this usually represents the maximum number the driver may use and not
the actual number in use.

For TX queues, drivers can update the actual number using
netif_set_real_num_tx_queues().  Add a corresponding function for RX
queues, netif_set_real_num_rx_queues().

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-27 22:09:49 -07:00
Eric Dumazet f91ff5b9ff net: sk_{detach|attach}_filter() rcu fixes
sk_attach_filter() and sk_detach_filter() are run with socket locked.

Use the appropriate rcu_dereference_protected() instead of blocking BH,
and rcu_dereference_bh().
There is no point adding BH prevention and memory barrier.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-27 21:30:44 -07:00
Eric Dumazet 7fa7cb7109 fib: use atomic_inc_not_zero() in fib_rules_lookup
It seems we dont use appropriate refcount increment in an
rcu_read_lock() protected section.

fib_rule_get() might increment a null refcount and bad things could
happen.

While fib_nl_delrule() respects an rcu grace period before calling
fib_rule_put(), fib_rules_cleanup_ops() calls fib_rule_put() without a
grace period.

Note : after this patch, we might avoid the synchronize_rcu() call done
in fib_nl_delrule()

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-27 21:30:44 -07:00
David S. Miller 01db403cf9 tcp: Fix >4GB writes on 64-bit.
Fixes kernel bugzilla #16603

tcp_sendmsg() truncates iov_len to an 'int' which a 4GB write to write
zero bytes, for example.

There is also the problem higher up of how verify_iovec() works.  It
wants to prevent the total length from looking like an error return
value.

However it does this using 'int', but syscalls return 'long' (and
thus signed 64-bit on 64-bit machines).  So it could trigger
false-positives on 64-bit as written.  So fix it to use 'long'.

Reported-by: Olaf Bonorden <bono@onlinehome.de>
Reported-by: Daniel Büse <dbuese@gmx.de>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-27 20:24:54 -07:00
David S. Miller e40051d134 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/qlcnic/qlcnic_init.c
	net/ipv4/ip_output.c
2010-09-27 01:03:03 -07:00
Eric Dumazet 1b4bf461f0 rps: allocate rx queues in register_netdevice only
Instead of having two places were we allocate dev->_rx, introduce
netif_alloc_rx_queues() helper and call it only from
register_netdevice(), not from alloc_netdev_mq()

Goal is to let drivers change dev->num_rx_queues after allocating netdev
and before registering it.

This also removes a lot of ifdefs in net/core/dev.c

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-26 19:04:07 -07:00
Eric Dumazet c5256c5123 net: propagate NETIF_F_HIGHDMA to vlans
Automatically allows vlans to get NETIF_F_HIGHDMA if underlying device
supports it.

On 32bit arches (and more precisely if CONFIG_HIGHMEM is enabled), it
can help to reduce cost of illegal_highdma() and __skb_linearize()
calls.

Tested on tg3 , bnx2, bonding, this worked very well.

This is a generalization of a patch provided by Yi Zou & Jeff Kirsher.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-26 18:27:15 -07:00
Eric Dumazet f064af1e50 net: fix a lockdep splat
We have for each socket :

One spinlock (sk_slock.slock)
One rwlock (sk_callback_lock)

Possible scenarios are :

(A) (this is used in net/sunrpc/xprtsock.c)
read_lock(&sk->sk_callback_lock) (without blocking BH)
<BH>
spin_lock(&sk->sk_slock.slock);
...
read_lock(&sk->sk_callback_lock);
...

(B)
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)

(C)
spin_lock_bh(&sk->sk_slock)
...
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
spin_unlock_bh(&sk->sk_slock)

This (C) case conflicts with (A) :

CPU1 [A]                         CPU2 [C]
read_lock(callback_lock)
<BH>                             spin_lock_bh(slock)
<wait to spin_lock(slock)>
                                 <wait to write_lock_bh(callback_lock)>

We have one problematic (C) use case in inet_csk_listen_stop() :

local_bh_disable();
bh_lock_sock(child); // spin_lock_bh(&sk->sk_slock)
WARN_ON(sock_owned_by_user(child));
...
sock_orphan(child); // write_lock_bh(&sk->sk_callback_lock)

lockdep is not happy with this, as reported by Tetsuo Handa

It seems only way to deal with this is to use read_lock_bh(callbacklock)
everywhere.

Thanks to Jarek for pointing a bug in my first attempt and suggesting
this solution.

Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-24 22:26:10 -07:00
Eric Dumazet a02cec2155 net: return operator cleanup
Change "return (EXPR);" to "return EXPR;"

return is not a function, parentheses are not required.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-23 14:33:39 -07:00
Andy Shevchenko 82fd5b5d1e net: core: use kernel's converter from hex to bin
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-21 18:04:45 -07:00
David S. Miller 73da16c28e ethtool: Fix build due to lack of ethtool.h include.
net/core/ethtool.c: In function 'ethtool_get_regs':
net/core/ethtool.c:818:2: error: implicit declaration of function 'vmalloc'
net/core/ethtool.c:818:9: warning: assignment makes pointer from integer without a cast
net/core/ethtool.c:833:2: error: implicit declaration of function 'vfree'

Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-21 16:12:11 -07:00
Ben Hutchings a77f5db361 ethtool: Allocate register dump buffer with vmalloc()
Some NICs have huge register files which exceed the maximum heap
allocation size.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-21 14:57:59 -07:00
Ingo Molnar 7ed569206e Merge commit 'v2.6.36-rc5' into perf/core
Merge reason: Pick up the latest fixes in -rc5.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-09-21 13:55:11 +02:00
Ben Hutchings be2902daee ethtool, ixgbe: Move RX n-tuple mask fixup to ethtool
The ethtool utility does not set masks for flow parameters that are
not specified, so if both value and mask are 0 then this must be
treated as equivalent to a mask with all bits set.  Currently that is
done in the only driver that implements RX n-tuple filtering, ixgbe.
Move it to the ethtool core.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-17 16:53:23 -07:00
David Lamparter 3b27e10555 netns: keep vlan slaves on master netns move
previously, if a vlan master device was moved from one network namespace
to another, all 802.1q and macvlan slaves were deleted.

we can use dev->reg_state to figure out whether dev_change_net_namespace
is happening, since that won't set dev->reg_state NETREG_UNREGISTERING.
so, this changes 8021q and macvlan to ignore NETDEV_UNREGISTER when
reg_state is not NETREG_UNREGISTERING.

Signed-off-by: David Lamparter <equinox@diac24.net>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-17 16:46:04 -07:00
Eric Dumazet 67c9660831 ethtool: change ethtool_set_gro() to use ethtool_op_get_rx_csum
To be able to switch on GRO on a device, ethtool_set_gro() checks this
device provides a get_rx_csum() method.

Some devices dont provide this method, while they do support RX
checksumming.

This patch allows bonding to support GRO :

ethtool -K bond0 gro on

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-17 11:56:18 -07:00
Stephen Rothwell caeda9b926 net: include inetdevice.h for rcu_dereference_raw api change
rcu_dereference_raw() now needs to know the type of its argument.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-16 21:39:16 -07:00
Brandon Philips 16c3ea785f net: enable GRO by default for vlan devices
Currently vlan devices don't have GRO by default as none of the Ethernet
drivers add NETIF_F_GRO to their vlan_features.

As GRO is a software feature add GRO to dev->vlan_features in
register_netdevice() and let vlan_dev_init() take care that it gets
enabled only when dev->features has NETIF_F_GRO too.

Signed-off-by: Brandon Philips <bphilips@suse.de>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-15 22:32:29 -07:00
Eric Dumazet 95ae6b228f ipv4: ip_ptr cleanups
dev->ip_ptr is protected by rtnl and rcu.

Yet some places dont use appropriate primitives and/or locking rules.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-15 22:06:05 -07:00
Ben Hutchings e0de7c93b9 ethtool: Remove unimplemented flow specification types
struct ethtool_rawip4_spec and struct ethtool_ether_spec are neither
commented nor used by any driver, so remove them.  Adjust padding in
the user-visible unions that included these structures.

Fix references to struct ethtool_rawip4_spec in
ethtool_get_rx_ntuple(), which should use struct ethtool_usrip4_spec.

struct ethtool_usrip4_spec cannot hold IPv6 host addresses and there
is no separate structure that can, so remove ETH_RX_NFC_IP6 and the
reference to it in niu.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-15 14:42:13 -07:00
Ingo Molnar 3aabae7d9d Merge branch 'tip/perf/core' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into perf/core 2010-09-15 10:27:31 +02:00
Eric Dumazet ef885afbf8 net: use rcu_barrier() in rollback_registered_many
netdev_wait_allrefs() waits that all references to a device vanishes.

It currently uses a _very_ pessimistic 250 ms delay between each probe.
Some users reported that no more than 4 devices can be dismantled per
second, this is a pretty serious problem for some setups.

Most of the time, a refcount is about to be released by an RCU callback,
that is still in flight because rollback_registered_many() uses a
synchronize_rcu() call instead of rcu_barrier(). Problem is visible if
number of online cpus is one, because synchronize_rcu() is then a no op.

time to remove 50 ipip tunnels on a UP machine :

before patch : real 11.910s
after patch : real 1.250s

Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Octavian Purdila <opurdila@ixiacom.com>
Reported-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-14 14:27:29 -07:00