The USB max packet size (always little-endian) was not being byte
swapped on big-endian systems.
Applicable since [USB: ftdi_sio: fix hi-speed device packet size calculation] approx 2.6.31
Signed-off-by: Michael Wileczka <mikewileczka@yahoo.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The definitions for BREAK_ON and BREAK_OFF are inverted, causing break
requests to fail. This patch sets BREAK_ON and BREAK_OFF to the correct
values.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Zeagle N2iTiON3 dive computer interface. Since
Zeagle devices are actually manufactured by Seiko, this patch will
support other Seiko based models as well.
Signed-off-by: Jef Driesen <jefdriesen@telenet.be>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch with title below makes reference count of usb serial module
always more than one after driver is bound.
USB-BKL: Remove BKL use for usb serial driver probing
In fact, the patch above only replaces lock_kernel() with try_module_get()
, and does not use module_put() to do what unlock_kernel() did, so casue leak
of reference count of usb serial module and the module can not be unloaded
after serial driver is bound with device.
This patch fixes the issue, also simplifies such things:
-only call try_module_get() once in the entry of usb_serial_probe()
-only call module_put() once in the exit of usb_serial_probe
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I recently bought a i-gotU USB GPS, and whilst hunting around for linux
support discovered this post by you back in 2009:
http://kerneltrap.org/mailarchive/linux-usb/2009/3/12/5148644
>Try the navman driver instead. You can either add the device id to the
> driver and rebuild it, or do this before you plug the device in:
> modprobe navman
> echo -n "0x0df7 0x0900" > /sys/bus/usb-serial/drivers/navman/new_id
>
> and then plug your device in and see if that works.
I can confirm that the navman driver works with the right device IDs on
my i-gotU GT-600, which has the same device IDs. Attached is a patch
adding the IDs.
From: Ross Burton <ross@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since handle_sysrq() does not take tty as argument anymore we can
drop it from usb_serial_handle_sysrq_char() as well.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sysrq operations do not accept tty argument anymore so no need to pass
it to us.
[Stephen Rothwell <sfr@canb.auug.org.au>: fix build breakage in drm code
caused by sysrq using bool but not including linux/types.h]
[Sachin Sant <sachinp@in.ibm.com>: fix build breakage in s390 keyboadr
driver]
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As David VomLehn points out, it was possible to receive an interrupt
before clearing the free-urb flag which could lead to the urb being
incorrectly marked as busy.
For the same reason, move tx_bytes accounting so that it will never be
negative.
Note that the free-flags set and clear operations do not need any
additional locking as they are manipulated while USB_SERIAL_WRITE_BUSY
is set.
Reported-by: David VomLehn <dvomlehn@cisco.com>
Tested-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Quatech SSU-100 single port usb to serial device.
This driver is based on the ftdi_sio.c driver and the original
serqt_usb driver from Quatech.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is to add a US Interface, Inc. "Navigator" USB device.
Specifically, it's a HAM Radio USB sound modem that also
incorporates three pairs of unique FTDI serial ports. The standard
Linux FTDI serial driver will only recognize the first two serial
ports of an unknown FDTI derived device and this patch adds in
recognition to these specific new IDs.
Signed-off-by: David A. Ranch <dranch@trinnet.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product IDs of Huawei's K3765 and K4505 mobile
broadband usb modems to option.c. It also adds a quirk to the option
probe function so that binding to the device's network interface(class
0xff) is avoided. This is necessary to allow another driver to bind to
that, and to avoid programs like wvdial opening a nonfunctioning tty
during modem discovery.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have added the ProductID=0xe729 VendorID=FTDI_VID=0x0403 which will
enable support for the Segway Robotic Mobility Platform (RMP200) in the
ftdi_sio kernel module. Currently, users of the Segway RMP200 must use
a RUN+="/sbin/modprobe -q ftdi-sio product=0xe729 vendor=0x0403 in a
udev rule to get the ftdi_sio module to handle the usb interface and
mount it on /dev/ttyXXX. This is not a good solution because some users
will have multiple USB to Serial converters which will use the ftdi_sio
module.
Signed-off-by: John Rogers <jgrogers@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch adds Huawei ETS 1220 product id into the list of supported
devices in 'option' usb serial driver.
Signed-off-by: Pavel Kazlou <p.i.kazlou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the write download record failed we shouldn't return 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Usb serial port device is child of its usb interface device, so
we can enable async suspend of usb serial port device to speedup
system suspend.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the write download record failed we shouldn't return 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb serial driver initialization tried to use the BKL to stop
driver modules from unloading, but that didn't work anyways.
There was already some code to do proper try_module_get,
but it was conditional on having a new probe interface.
I checked all the low level drivers and they all have proper
.owner = THIS_MODULE, so it's ok to always use.
The other problem was the usb_serial_driver_list needing
protection by a lock. This was broken anyways because unregister
did not necessarily have the BKL.
I extended the extending table_lock mutex to protect this case too.
With these changes the BKL can be removed here.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ipaq already had this device id defined:
{ USB_DEVICE(0x0BB4, 0x00CF) }, /* HTC USB Modem */
Revert the commit which adds the duplicate entry.
This reverts commit 04cab13293.
Originally-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AMOI_VENDOR_ID is defined twice. Remove the duplicate entry and move
the AMOI_PRODUCT_9508 definition to be grouped with the other AMOI
product definitions.
Originally-by: Ben Collins <ben.collins@ubuntu.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This now refcounts but doesn't actually check the reference was obtained in
all the places it should.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg prefers this to go through the trivial tree.
http://lkml.org/lkml/2010/6/24/1
There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.
Standardize them a bit.
Moved a statement down a line in drivers/usb/host/u132-hcd.c
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
RT Systems has put out bunch of ham radio cables based on the FT232RL
chip. Each cable type has a unique PID, this adds one for the Yaesu VX-7
radios.
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usbserial: Add AMOI Skypephone S2 support.
This patch adds support for the AMOI Skypephone S2 to the usbserial module.
Tested-by: Dennis Jansen <Dennis.Jansen@web.de>
Signed-off-by: Dennis Jansen <Dennis.Jansen@web.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for the Generic Qualcomm Gobi 2000 WWAN UMTS/CDMA modem
Signed-off-by: Andrew Bird <ajb@spheresytems.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ftdi_sio: support for Signalyzer tools based on FTDI chips
This patch adds support for the Xverve Signalyzers.
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add VID/PID for Sierra Wireless 250U USB dongle to sierra.c
Allows use of 3G radio only
Signed-off-by: August Huber <gus@pbx.org>
Cc: Elina Pasheva <epasheva@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds missing kfree(data) before return -ENODEV.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch corrects a problem with the merge of a previous
patch to add the CONTEC identifier.
I believe the merge problem occurred with the commit:
dee5658b48
Originally I submitted a patch and then they asked me to order the IDs
and resubmit, so did I. But unfortunately in the end somehow both
patches were merged.
Signed-off-by: Daniel Sangorrin <daniel.sangorrin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If port is NULL, then the call to dev_err will dereference a value that is
a small offset from NULL.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E,E1;
identifier f;
statement S1,S2,S3;
@@
if ((E == NULL && ...) || ...)
{
... when != if (...) S1 else S2
when != E = E1
* E->f
... when any
return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Call set_mctrl() and clear_mctrl() according to the flow control mode
selected. This makes serial communication for FT232 connected devices
work when CRTSCTS is not set.
This fixes a regression introduced by 4175f3e31 ("tty_port: If we are
opened non blocking we still need to raise the carrier"). This patch
calls the low-level driver's dtr_rts() function which consequently sets
TIOCM_DTR | TIOCM_RTS. A later call to set_termios() without CRTSCTS in
cflags, however, does not reset these bits, and so data is not actually
sent out on the serial wire.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Length field of header was incorrectly set to available payload space
rather than the actual payload size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom read and write implementations (static per-port,
singleton(!) urb pool).
Also remove changelog header (can be retrieved through git).
Read processing and write-buffer handling tested using a cp210x device
in a loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Private data was not freed on error path in startup.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up read processing logic.
Tested using a cp210x device in a loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom single-urb write implementation.
Note that this driver still depended on the write callback from the old
generic framework.
Tested against original read processing using a cp210x device in a
loopback setup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill private write fifo and use port fifo instead (protected under
port lock).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom fifo implementation.
Use private write fifo to minimise changes to lock handling.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom fifo implementation.
Note that cypress_m8 has no port write fifo as it has no bulk-out
endpoint.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use bulk_out_size in usb_serial_driver to set urb buffer size.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increase the bulk-out buffer size to avoid any regression in throughput
after replacing the old writing scheme which used dynamic buffers (e.g.
up to 2k).
256b has been determined to be a good choice for several drivers
including ftdi_sio which used to have a more or less identical write
implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use process_read_urb to implement line status handling.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom read and write implementations (dynamically allocated write
urbs).
Note that I chose to remove the stat module parameter which was supposed
to keep count of the amount of data sent and received, but which has
been broken for three years (since b308e74d9c
"USB: visor driver adapted to new tty buffering" -- bytes_in was
incorrectly updated and was thus always reported as 0).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix memory leak for some devices (Sony Clie 3.5) due to port private
data not being freed on release.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom fifo, read and write implementations (single-urb and fifo,
but still maintained list of 256*256b urb buffers per port).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill custom read and write implementations (static 16*4k write-urb pool
shared among all ports in system).
Also remove old changelog entries in header (code is now gone, and
these entries can still be retrieved through git).
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Return immediately from generic process_read_urb if urb is empty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An urb transfer buffer is allocated at every open but was never freed.
This driver is a bit of a mess...
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for an olivetti olicard100 HЅDPA usb-stick.
This device is a zeroCD one with ID 0b3c:c700 that needs switching via
eject or usb-modeswitch with
MessageContent="5553424312345678000000000000061b000000030000000000000000000000".
After switching it has ID 0b3c:c000 and provides 5 serial ports ttyUSB[0-4].
Port 0 (modem) and 4 are interrupt ports.
Signed-off-by: Nils Radtke <lkml@Think-Future.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove cp210x_disconnect which is used to kill traffic although this is
already handled by the generic framework.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No need to raise dtr/rts in open as this is taken care of by tty layer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use dynamically allocated urb for baudrate changes rather than
unconditionally submitting the port write urb which may already be in
use.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use usb_serial_driver bulk_in_size and bulk_out_size to make sure
buffers of appropriate sizes are allocated in the first place rather than
reallocating them at every open.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the user specifies a custom bulk buffer size we get a double free at
port release.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reverse priority of errors reported to ldisc so that it matches that of
other serial drivers (break takes precedence over parity, which takes
precedence over framing errors).
Also make sure overrun errors are handled as in other drivers, that is,
an overrun error is always reported and is not associated with any
received character (instead a NULL character with the TTY_OVERRUN flag
set is inserted).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use tty_insert_flip_string_fixed_flag to report errors to line
discipline.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use tty_insert_flip_string_fixed_flag to report errors to line
discipline.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix regression introduced by commit
a108bfcb37 (USB: tty: Prune uses of
tty_request_room in the USB layer) which broke three drivers
(cypress_m8, digi_acceleport and spcp8x5) through incorrect use of
tty_insert_flip_string_fixed_flag.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org> [.34]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove multi-urb write from the generic driver and simplify the
prepare_write_buffer prototype:
int (*prepare_write_buffer)(struct usb_serial_port *port,
void *dest, size_t size);
The default implementation simply fills dest with data from port write
fifo but drivers can override it if they need to process the outgoing
data (e.g. add headers).
Turn ftdi_sio into a generic fifo-based driver, which lowers CPU usage
significantly for small writes while retaining maximum throughput.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reimplement fifo-based writes in the generic driver using a multiple
pre-allocated urb scheme.
In contrast to multi-urb writes, no allocations (of urbs or buffers) are
made during run-time and there is less pressure on the host stack
queues as currently only two urbs are used (implementation is generic
and can handle more than two urbs as well, though).
Initial tests using ftdi_sio show that the implementation achieves the
same (maximum) throughput at high baudrates as multi-urb writes. The CPU
usage is much lower than for multi-urb writes for small write requests
and only slightly higher for large (e.g. 2k) requests (due to extra copy
via fifo?).
Also outperforms multi-urb writes for small write requests on an
embedded arm-9 system, where multi-urb writes are CPU-bound at high
baudrates (perf reveals that a lot of time is spent in the host stack
enqueue function -- could perhaps be a bug as well).
Keeping the original write_urb, buffer and flag for now as there are
other drivers depending on them.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill circular buffers for tx and rx as well as read work thread, and
switch to generic kfifo-based write implementation.
This is an example of how prepare_write_buffer and process_read_urb can
be used to handle protocols with packet headers.
Please note the diffstat which shows that the same functionality is now
provided using only a tenth of the code (including whitespace and
comments, though).
Tested-by: Naranjo, Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original SIO devices require a control byte for every packet
written. Clean up the unnecessarily messy implementation of this.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch to the generic, multi-urb, write implementation.
Note that this will also make it fairly easy to use the generic
fifo-based write implementation: simply unset the multi_urb_write flag
and modify prepare_write_buffer (or unset if not using a legacy SIO
device). This may be desirable for instance on an embedded system where
optimal throughput at high baudrates may not be as important as other
factors (e.g. no allocations during runtime and less pressure on host
stack).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another CDC-ACM + vendor specific interface layout.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
BKL isn't anymore present into this file thus it is no necessary still include smp_lock.h.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix mos7720 Kconfig dependencies.
When an enabled bool selects a tristate, the tristate becomes =y,
even if it should be limited to modular, so limit the bool kconfig
option to configs that will build cleanly.
Also change the if-block to a simple depends on.
drivers/built-in.o: In function `mos7720_release':
mos7720.c:(.text+0xad432): undefined reference to `parport_remove_port'
drivers/built-in.o: In function `mos7715_parport_init':
mos7720.c:(.text+0xae197): undefined reference to `parport_register_port'
mos7720.c:(.text+0xae210): undefined reference to `parport_announce_port'
drivers/built-in.o:(.data+0x201c8): undefined reference to `parport_ieee1284_read_nibble'
drivers/built-in.o:(.data+0x201d0): undefined reference to `parport_ieee1284_read_byte'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
No functionality added or bugs fixed, just improved code consistency and
(hopefully) readability by replacing send_mos_cmd with the register read & write
functions that were used for parallel port registers. Also shortens overall
file length.
Thoroughly tested, with emphasis on regression testing the serial port.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the parallel port on the moschip MCS7715 device. The port
registers itself with the parport subsystem as a low-level driver. A separate
entry to the kernel configuration is added beneath that for the mos7720, to
avoid the need to link with the parport subsystem code for users who don't have
or don't want the parallel port. Only compatibility mode is currently supported
(no ECP/EPP). Tested with both moschip devices (7720 and 7715) on UP and SMP
hosts, including regression testing of serial port, concurrent operation of
serial and parallel ports, and various connect / disconnect scenarios.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ids for Qualcomm Gobi 2000 QDL and Modem modes. Gobi 2000 has a
single altsetting in QDL mode, so adapt code to handle that.
Firmware upload protocol is also slightly different, with an
additional firmware file. However, qcserial doesn't handle firmware
uploading.
Tested on Lenovo Thinkpad T510.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make qcserial use the generic USB wwan code. This should result in a
performance improvement.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As this code was simply factored out of option, this is a simple
conversion.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The generic USB serial code is ill-suited for high-speed USB wwan devices,
resulting in the option driver. However, other non-option devices may also
gain similar benefits from not using the generic code. Factorise out the
non-option specific code from the option driver and make it available to
other users.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All unsuccessful (non-zero status) URBs were being dropped. After N_IN_URBs are
dropped you will no longer be able to receive data.
This patch resubmits unsuccessful URBs unless the status indicates that it should
be terminated. The statuses that indicate the URB should be terminated was
gathered from other similar drivers.
Signed-off-by: James Maki <jamescmaki@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Generalise write buffer preparation.
This allows for drivers to manipulate (e.g. add headers) to bulk out
data before it is sent.
This adds a new function pointer to usb_serial_driver:
int (*prepare_write_buffer)(struct usb_serial_port *port,
void **dest, size_t size, const void *src, size_t count);
The function is generic and can be used with either kfifo-based or
multi-urb writes:
If *dest is NULL the implementation should allocate dest.
If src is NULL the implementation should use the port write fifo.
If not set, a generic implementation is used which simply uses memcpy or
kfifo_out.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use dynamic transfer buffer sizes since it is more efficient to let the
host controller do the partitioning to fit endpoint size. This way we
also do not use more than one urb per write request.
Replace max_in_flight_urbs with multi_urb_write flag in struct
usb_serial_driver to enable multi-urb writes.
Use MAX_TX_URBS=40 and a max buffer size of PAGE_SIZE to prevent DoS
attacks.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow drivers to implement their own multi-urb write bulk callbacks as
we do for single urb writes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the generic kfifo-based write implementation rather than allowing up
to 4000 8 byte urbs in the host stack queues.
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use usb_serial_generic_close to kill the read and write urbs and to
reset the write fifo.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Submit write urb if it is not already in use and we have buffered data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch to generic read implementation and use process_read_urb to do
device specific processing (handle line status).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow drivers to use the generic throttle and unthrottle implementation.
This makes sense for drivers using the generic read functionality.
Note that drivers need to set these explicitly in order to enable them
(i.e., we do not set them at port probe if not defined).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use generic read implementation and use process_read_urb to do device
specific processing (handle line status).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add process_read_urb to usb_serial_driver so that a driver can rely on
the generic read (and throttle) mechanism but still do device specific
processing of incoming data (such as adding tty_flags before pushing to
line discipline).
The default generic implementation handles sysrq for consoles but
otherwise simply pushes to tty.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Always process and flush read urb, but only resubmit when not throttled.
The new tty-layer supply plenty of slack so there is really no need to
cache and delay processing of a single urb while throttled.
Note that unthrottle now submits using GFP_KERNEL as we are not in
atomic context (so there is no need to save irq state either).
Note also that the process_read_urb function could be added to
usb_serial_driver should any driver need to do any device specific
processing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need to initialise the read urb as this is done at port
probe.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The generic read and write bulk urbs are initialised when allocated in
usb_serial_probe. The only field that needs to be updated after that is
the transfer_buffer_length of the write urb.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the already exported function for submitting the read urb associated
with a usb_serial_port.
Make sure it returns the result of usb_submit_urb and rename to the
more descriptive usb_serial_generic_submit_read_urb.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Export usb_serial_generic_close so that drivers can easily kill the read
and write urb and make sure that the write fifo is reset.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On errors the fifo was reset without any locking. This could race with
write which do kfifo_put and perhaps also chars_in_buffer and write_room.
Every other access to the fifo is protected using the port lock so
better add it to the error path as well.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure chars_in_buffer accounts also for data in host stack queues.
This fixes the problem with tty_wait_until_sent returning too soon at
close which could cause the final write urb to be cancelled.
Reported-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pl2303 requires a bulk-in buffer larger than endpoint size to keep
up at high baudrates without loosing data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increase the bulk-out buffer size from 64 to 256 byte.
This gives a significant increase in throughput already at 1Mbaud as well
as lowered CPU usage. The buffer is big enough to keep up also at 3Mbaud
(128b would not suffice).
64b 256b
921k: 640 KB/s 870 KB/s
3M: 640 KB/s 2520 KB/s
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The cp210x requires a bulk-in buffer larger than endpoint size to keep
up at high baudrates without loosing data.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Increase the bulk-out buffer size from 64 to 256 byte.
This gives a significant increase in throughput already at 1Mbaud
(e.g. 710 instead of 640 KB/s) as well as lowered CPU usage.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow drivers to define custom bulk in/out buffer sizes in struct
usb_serial_driver. If not set, fall back to the default buffer size
which matches the endpoint size.
Three drivers are currently freeing the pre-allocated buffers and
allocating larger ones to achieve this at port probe (ftdi_sio) or even
at port open (ipaq and iuu_phoenix), which needless to say is suboptimal.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build error when CONFIG_MAGIC_SYSRQ is not enabled:
drivers/usb/serial/generic.c:566: error: implicit declaration of function 'handle_sysrq'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb console code has had a long standing problem of not being able
to pass the baud rate from the kernel argument console=ttyUSB0,BAUD
down to the initial tty open, unless you were willing to settle for
9600 baud.
The solution is to directly use tty_init_termios() in
usb_console_setup() as this will preserve any changes to the initial
termios setting on future opens.
CC: Alan Cox <alan@linux.intel.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace all instances of using the console variable in struct
usb_serial_port with the struct tty_port version.
CC: Alan Cox <alan@linux.intel.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix printk format warning in usbserial/ti_usb:
drivers/usb/serial/ti_usb_3410_5052.c:1738: warning: format '%d' expects type 'int', but argument 5 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PATCH TO EXTEND SUPPORT TO AC8710 WITH 0xFFFF Product ID.
Signed-off-by: Mahesh Kuruganti <maheshkuruganti@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on the information provided for by Paweł Drobek, add
a second vendor ID and the correct product ID for ZTE MF 330.
Reported-by: Paweł Drobek <pawel.drobek@gmail.com>
Signed-off: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I read a rumor that the AdLink ND6530 USB RS232, RS422 and RS485
isolated adapter is actually a PL2303 based usb serial adapter. I
tried it out, and as far as I can tell it works.
Signed-off-by: Manuel Jander <manuel.jander@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These phones also have the familiar ttyACM0/ttyUSB0 schizophrenia when
placed into "Dial-up Networking" mode after connecting a USB cable.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch adds support for Multitech Systems' MT9234MU and
MT9234ZBA usb dialup fax modems. It is based on a patch and firmware
provided to me by Multitech Systems' support, after I reported to them
that my MT9234MU modem was not working with recent linux kernels.
Signed-off-by: Alex Manoussakis <alex@juniper.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty_port,usb-console: Fix usb serial console open/close regression
tty: cpm_uart: use resource_size()
tty_buffer: Fix distinct type warning
hvc_console: Fix race between hvc_close and hvc_remove
uartlite: Fix build on sparc.
tty: Take a 256 byte padding into account when buffering below sub-page units
Revert "tty: Add a new VT mode which is like VT_PROCESS but doesn't require a VT_RELDISP ioctl call"
This patch removes a double usb_control_msg that sets the cp210x
configuration registers a second time when calling cp210x_set_config.
For data sizes >2 the second write gets corrupted.
The patch has been created against 2.6.34-rc1, but all cp210x driver
revisions are affected.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The change_speed() function should be serialized against multiple calls.
Use the cfg_lock mutex to do this.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The module is called qcaux and not moto_modem. Also use help instead of
---help-- to be in sync with the other Kconfig entries.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to ftdi_sio_ids.h and ftdi_sio.c that adds identifiers for
CONTEC USB serial converter. I tested it with the device COM-1(USB)H
[akpm@linux-foundation.org: keep the VIDs sorted a bit]
Signed-off-by: Daniel Sangorrin <daniel.sangorrin@gmail.com>
Cc: Andreas Mohr <andi@lisas.de>
Cc: Radek Liboska <liboska@uochb.cas.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds various USB device IDs for Gobi 2000 devices, as found in the
drivers available at https://www.codeaurora.org/wiki/GOBI_Releases
Signed-off-by: Bernhard Rosenkraenzer <bero@arklinux.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found a DLink DWM 652 U5 USB 3G modem has product ID 0xce1e instead
of orignal 0xce16. The new ID is added.
And I found there are two entries for 0xce16, one has raw number, the
other has symbol DLINK_PRODUCT_DWM_652_U5. This is fixed too.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is possible to have a multi-port device with a port lacking an in or
out bulk endpoint. Only checking for num_bulk_in or num_bulk_out is thus not
sufficient to determine whether a specific port has an in or out bulk
endpoint.
This fixes potential null pointer dereferences in the generic open and
write routines, as well as access to uninitialised fifo in write_room
and chars_in_buffer.
Also let write fail with ENODEV (instead of 0) on missing out endpoint
(also on zero-length writes).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure usb_serial_port_softint is called on errors also when using
multi urb writes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resubmitting read urb fails with -EPERM if completion handler runs while
urb is being killed on close. This should not be reported as an error.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit e1108a63e1 ("usb_serial: Use the
shutdown() operation") breaks the ability to use a usb console
starting in 2.6.33. This was observed when using
console=ttyUSB0,115200 as a boot argument with an FTDI device. The
error is:
ftdi_sio ttyUSB0: ftdi_submit_read_urb - failed submitting read urb, error -22
The handling of the ASYNCB_INITIALIZED changed in 2.6.32 such that in
tty_port_shutdown() it always clears the flag if it is set. The fix
is to add a variable to the tty_port struct to indicate when the tty
port is a console.
CC: Alan Cox <alan@linux.intel.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (220 commits)
USB: backlight, appledisplay: fix incomplete registration failure handling
USB: pl2303: remove unnecessary reset of usb_device in urbs
USB: ftdi_sio: remove obsolete check in unthrottle
USB: ftdi_sio: remove unused tx_bytes counter
USB: qcaux: driver for auxiliary serial ports on Qualcomm devices
USB: pl2303: initial TIOCGSERIAL support
USB: option: add Longcheer/Longsung vendor ID
USB: fix I2C API usage in ohci-pnx4008.
USB: usbmon: mask seconds properly in text API
USB: sisusbvga: no unnecessary GFP_ATOMIC
USB: storage: onetouch: unnecessary GFP_ATOMIC
USB: serial: ftdi: add CONTEC vendor and product id
USB: remove references to port->port.count from the serial drivers
USB: tty: Prune uses of tty_request_room in the USB layer
USB: tty: Add a function to insert a string of characters with the same flag
USB: don't read past config->interface[] if usb_control_msg() fails in usb_reset_configuration()
USB: tty: kill request_room for USB ACM class
USB: tty: sort out the request_room handling for whiteheat
USB: storage: fix misplaced parenthesis
USB: vstusb.c: removal of driver for Vernier Software & Technology, Inc., devices and spectrometers
...
No need to check ASYNCB_INITIALIZED anymore as commit
e1108a63e1 (usb_serial: Use the shutdown()
operation) make sure that there is no longer any call to unthrottle
after device specific close (in which the read urb is killed).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qcaux: add driver for QCDM-capable ports on various devices
Many Qualcomm-based devices provide a CDC-ACM port which accepts
normal AT commands and PPP connections. But they only provide one
which makes status or signal strength requests impossible while
PPP is active. They also provide secondary USB interfaces that
talk the Qualcomm Diagnostic Monitor (QCDM) protocol which can be
used for status and strength. Make those QCDM ports accessible.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've got a trivial patch for the pl2303 driver, that's what I needed to
make the wacom serial tablet driver work properly. It uses the
TIOCGSERIAL ioctl to determine if it's talking to a serial device or
not, which I gather is rather common, but the pl2303 driver didn't
implement that ioctl.
Here's a patch, I'm not sure it's absolutely correct, I mostly looked at
other similar usbserial drivers to see what I must do, but it works for
me.
Signed-off-by: John Tsiombikas <nuclear@member.fsf.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Longcheer is a Chinese company that manufactures the devices which a
bunch of different companies like Alcatel, 4G Systems, and Mobidata
rebrand. While I can't find Longcheer's USB ID registered anywhere,
it's pretty clear the ID is theirs.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to ftdi_sio_ids.h and ftdi_sio.c that adds
identifiers for CONTEC USB serial converter. I tested it
with the device COM-1(USB)H
Signed-off-by: Daniel Sangorrin <daniel.sangorrin@gmail.com>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1344) removes references to port->port.count from the
USB serial drivers. Now that serial ports are properly reference
counted, port.count checking is unnecessary and incorrect. Drivers
should assume that the port is in use from the time the open method
runs until the close method is called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have lots of callers that do not need to do this in the first place.
Remove the calls as they both cost CPU and for big buffers can mess up the
multi-page allocation avoidance.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver has its own (surplus) backup queue system which wants removing
from the receive overflow logic.
Do this at the same time as removing the request_room logic
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A crash has been reported with sierra driver on disconnect with
Ubuntu/Lucid distribution based on kernel-2.6.32.
The cause of the crash was determined as "NULL tty pointer was being
referenced" and the NULL pointer was passed by sierra_indat_callback().
This patch modifies sierra_indat_callback() function to check for NULL
tty structure pointer. This modification prevents a crash from happening
when the device is disconnected.
This patch fixes the bug reported in Launchpad:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/511157
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new function to the sierra.c driver, sierra_reset_resume().
This new function completes the suite of Dynamic Power Management commands
in the sierra.c driver.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/serial/sierra.c | 30 ++++++++++++++++++++----------
1 file changed, 20 insertions(+), 10 deletions(-)
We are now refcounted and all the port.count checking is no longer valid
and in fact produces false warnings.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As reported in
http://bugzilla.kernel.org/show_bug.cgi?id=10980
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reduces string space a bit
Neaten a macro redefine of dbg
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for USB serial interface provided by ViVOtech ViVOpay devices via
new driver vivopay-serial. Currently only the ViVOpay 8800 device is supported,
but support for similar devices can be added by adding the appropriate device
IDs to the driver.
Signed-off-by: Forest Bond <forest.bond@outpostembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Alan Cox have pinpointed the driver still required protection against
parallels calls to the config ioctl(). If lock is still necessary the use of
BKL is abused here. So replace BKL with a more convenient mutex.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the serial port on devices based on the MosChip 7715,
which provides a serial and parallel port on a single usb interface.
This is added to the existing driver for the Moschip 7720 dual serial
port device. The 7715 is very similiar to the 7720, requiring only the
addition of a calc_num_ports() function, a separate interrupt-in
endpoint callback, and some manipulation of the port pointers added to
the attach() function to correct the fact that the usbserial core
erroneously assigns the first bulk in/out endpoint pair to the serial
port (the 7715 uses these for its parallel port). There is no support
for the 7715's parallel port yet.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold points out that get_string() is basically just a
re-implimentation of usb_string(). It is also buggy. It does DMA on
the stack and it doesn't handle negative returns from
usb_get_descriptor(). Plus unicode_to_ascii() is a rubbish function and
moving to usb_string() avoids using it.
Let's eliminate get_string() entirely.
Reported-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- correct spelling/whitespace in ftdi_sio.h and ftdi_sio_ids.h
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The variables priv and portdata are initialized twice to the same (side
effect-free) expressions. Drop one initialization in each case.
A simplified version of the semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@forall@
idexpression *x;
identifier f!=ERR_PTR;
@@
x = f(...)
... when != x
(
x = f(...,<+...x...+>,...)
|
* x = f(...)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 4G XS Stick W14 seems to not understand RTS/DTR setting in
option_send_setup causing long timeouts on any open() which disturbs a
lot of well-known userspace applications like minicom or ModemManager.
Therefore, we enable OPTION_BLACKLIST_SENDSETUP blacklisting for it.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As suggested by Matthias Urlichs, this patch adds a somehow generic
mechanism for special handling of devices which don't support all bits
expected by this driver.
The blacklisting code is heavily stolen from sierra.c, but extended to
support different special cases.
For now, one case is implemented (OPTION_BLACKLIST_SENDSETUP), targeted
at the 4G W14 device: devices which don't understand the setting of
RTS/DTR in option_send_setup() causing a USB timeout of 5 s in any
userspace open() which leads to errors in most userspace applications.
In addition, I prepared another case for devices with interfaces which
shall not be accessed by this driver (targeted at the D-Link DWM 652).
However, OPTION_BLACKLIST_RESERVED_IF is not fully implemented yet as I
have no device to test this. Anyone volunteering to help here? If not,
I'll contact the guys who added D-Link DWM 652 support soon.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Carsten Juttner thankfully investigated a bit and found out some details
about the chipset used in the 4G W14 device I recently added to
option.c.
I think this information is useful for reference, so I'd be happy if you
could include those bits.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original code was passing a stack variable as a dma buffer, so I
made it an allocated variable. Instead of adding a bunch of kfree()
calls, I changed all the error return paths to gotos.
Also I noticed that the error checking wasn't correct because
usb_get_descriptor() can return negative values.
While I was at it, I made an unrelated white space change by moving
the unicode_to_ascii() on to one line.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill string that is allocated and generated using speed and parity
settings but is never used (and never has been).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change data-argument type from (void *) to (u8 *) to prevent endianess
problems.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Return values are being initialised to zero only to be unconditionally
assigned to a few instructions later. This may give the impression that
zero is returned on success, which is not the case.
Note also that ftdi_NDI_device_setup never reports errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also remove unnecessary buffer allocations for zero-length transfers.
Reported-by: Matti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also fixes DMA transfer to stack for latency buffer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've got a crappy cypress converter here, and while running at higher
baud rates craps out on throughput, it works fine with lower ones.
While it'd be nice to simply use a lower baud rate, not all devices
can be configured this way, and it is possible to (slowly) interact
at higher rates by sending a byte at a time. So let people force
higher rates when they need it via a module parameter.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current code has a confusing duplicate new_baudrate init when setting
the serial parameters. So just combine the if statement checks to avoid
this.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB_SERIAL_DEBUG Kconfig is for the USB serial debug driver, not for
generically enabling debug output in random USB serial drivers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My distro kernel (Fedora Rawhide) started throwing warnings from DMA API
checker, so I have no choice but band-aid it quick. There's no attempt
to reuse DMA buffers. Control messages are only sent rarely anyway.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed CS5 and CS6 from data bits since these are not supported
in FTDI hardware.
Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Latency timeout was read but never stored on port probe. When
ASYNC_LOW_LATENCY was cleared the device timeout would get set to 0
rather than the default 16ms.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We always push characters to ldisc immediately regardless of
ASYNC_LOW_LATENCY.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resubmitting read urb fails with -EPERM if completion handler runs while
urb is being killed on close. This should not be reported as an error.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for Dell Computer Corp. Wireless 5720 VZW Mobile
Broadband (EVDO Rev-A) Minicard GPS Port. I stole the name from lsusb,
but my card does not have a GPS on it (at least not that I can make
function). I'm sure the patch is whitespace damaged but the one line
addition should be fairly straightforward nonetheless.
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- add FTDI device IDs for several ELV devices and NXTCam of Lego Mindstorms NXT
- add hopefully helpful new_id comment
- remove less helpful "Due to many user requests for multiple ELV devices we enable
them by default." comment (we simply add _all_ known devices - an
enduser shouldn't have to fiddle with obscure module parameters...).
- add myself to DRIVER_AUTHOR
The missing NXTCam ID has been found at
http://www.unixboard.de/vb3/showthread.php?t=44155
, ELV devices taken from ELV Windows .inf file.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
added new device pid (PAPOUCH_AD4USB_PID) to ftdi_sio.h and ftdi_sio.c
AD4USB measuring converter is a 4-input A/D converter which enables the
user to measure to four current inputs ranging from 0(4) to 20 mA or
voltage between 0 and 10 V. The measured values are then transferred to
a superior system in digital form. The AD4USB communicates via USB.
Powered is also via USB. datasheet in english is here:
http://www.papouch.com/shop/scripts/pdf/ad4usb_en.pdf
Signed-off-by: Radek Liboska <liboska@uochb.cas.cz>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix a regression introduced by commit
715b1dc01f ("USB: usb_debug,
usb_generic_serial: implement multi urb write").
URB transfer buffer was never freed when using multi-urb writes.
Currently the only driver enabling multi-urb writes is usb_debug.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fix a possible race bug in drivers/usb/serial/generic with
the new kfifo API.
Please apply it to the 2.6.33-rc* tree.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a (almost) sort-only patch to sort FTDI device
product ID definitions in new ftdi_sio_ids.h header.
Advantage is that new device ID submissions will now have a specific (sorted)
position - less future merge conflicts.
Compile-tested, based on _current_ mainline git.
Minor checkpatch.pl warnings were eliminated whereever it made sense,
very minor text changes.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a strictly move-only patch to relocate all FTDI device
product ID definitions to their own ftdi_sio_ids.h header
(following the usual *_ids.h kernel tree convention, too),
thus correcting the slightly too messy appearance
(crucial driver defines were stuck somewhere in the decaying middle swamp
of the huge existing header).
Compile-tested, based on latest mainline git.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB serial code was a new user of the kfifo API, and it was missed
when porting things to the new kfifo API.
Please make the write_fifo in place. Here is my patch to fix the
regression and full ported version.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Reported-and-tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Greg KH <greg@kroah.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rename kfifo_put... into kfifo_in... to prevent miss use of old non in
kernel-tree drivers
ditto for kfifo_get... -> kfifo_out...
Improve the prototypes of kfifo_in and kfifo_out to make the kerneldoc
annotations more readable.
Add mini "howto porting to the new API" in kfifo.h
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the pointer to the spinlock out of struct kfifo. Most users in
tree do not actually use a spinlock, so the few exceptions now have to
call kfifo_{get,put}_locked, which takes an extra argument to a
spinlock.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new generic kernel FIFO implementation.
The current kernel fifo API is not very widely used, because it has to
many constrains. Only 17 files in the current 2.6.31-rc5 used it.
FIFO's are like list's a very basic thing and a kfifo API which handles
the most use case would save a lot of development time and memory
resources.
I think this are the reasons why kfifo is not in use:
- The API is to simple, important functions are missing
- A fifo can be only allocated dynamically
- There is a requirement of a spinlock whether you need it or not
- There is no support for data records inside a fifo
So I decided to extend the kfifo in a more generic way without blowing up
the API to much. The new API has the following benefits:
- Generic usage: For kernel internal use and/or device driver.
- Provide an API for the most use case.
- Slim API: The whole API provides 25 functions.
- Linux style habit.
- DECLARE_KFIFO, DEFINE_KFIFO and INIT_KFIFO Macros
- Direct copy_to_user from the fifo and copy_from_user into the fifo.
- The kfifo itself is an in place member of the using data structure, this save an
indirection access and does not waste the kernel allocator.
- Lockless access: if only one reader and one writer is active on the fifo,
which is the common use case, no additional locking is necessary.
- Remove spinlock - give the user the freedom of choice what kind of locking to use if
one is required.
- Ability to handle records. Three type of records are supported:
- Variable length records between 0-255 bytes, with a record size
field of 1 bytes.
- Variable length records between 0-65535 bytes, with a record size
field of 2 bytes.
- Fixed size records, which no record size field.
- Preserve memory resource.
- Performance!
- Easy to use!
This patch:
Since most users want to have the kfifo as part of another object,
reorganize the code to allow including struct kfifo in another data
structure. This requires changing the kfifo_alloc and kfifo_init
prototypes so that we pass an existing kfifo pointer into them. This
patch changes the implementation and all existing users.
[akpm@linux-foundation.org: fix warning]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (58 commits)
tty: split the lock up a bit further
tty: Move the leader test in disassociate
tty: Push the bkl down a bit in the hangup code
tty: Push the lock down further into the ldisc code
tty: push the BKL down into the handlers a bit
tty: moxa: split open lock
tty: moxa: Kill the use of lock_kernel
tty: moxa: Fix modem op locking
tty: moxa: Kill off the throttle method
tty: moxa: Locking clean up
tty: moxa: rework the locking a bit
tty: moxa: Use more tty_port ops
tty: isicom: fix deadlock on shutdown
tty: mxser: Use the new locking rules to fix setserial properly
tty: mxser: use the tty_port_open method
tty: isicom: sort out the board init logic
tty: isicom: switch to the new tty_port_open helper
tty: tty_port: Add a kref object to the tty port
tty: istallion: tty port open/close methods
tty: stallion: Convert to the tty_port_open/close methods
...
Opticon now takes the right mutex to check the port status but the status
check is done wrongly for the modern serial code, so fix it.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The tty port has a port mutex used for all the port related locking so we
don't need the one in the USB serial layer any more.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Alan Stern pointed out - now we have tty_port_open the shutdown method
and locking allow us to whack the other bits into the full helper methods
and provide a shutdown op which the tty port code will synchronize with
setup for us.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For the moment this just moves the USB logic over and fixes the 'what if
we open and hangup at the same time' race noticed by Oliver Neukum.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1302) removes the auto_pm flag from struct usb_device.
The flag's only purpose was to distinguish between autosuspends and
external suspends, but that information is now available in the
pm_message_t argument passed to suspend methods.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be switched
to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
The MessageContent for usb_modeswitch.conf is:
"55534243e0c26a85000000000000061b000000020000000000000000000000"
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch deals with reducing the memory footprint for sierra driver.
This optimization is aimed for embedded software customers.
Some sierra modems can expose upwards of 7 USB interfaces, each possibly
offering different services. In general, interfaces used for the
exchange of wireless data require much higher throughput, hence require
more memory (i.e. more URBs) than lower performance interfaces. URBs
used for the IN direction are pre-allocated by the driver and this patch
introduces a way to configure the number of IN URBs allocated on a
per-interface basis. Interfaces with lower throughput requirements
receive fewer URBs, thereby reducing the RAM memory consumed by the
driver.
NOTE1: This driver has always pre-allocated URBs for the IN direction.
NOTE2: The number of URBs pre-allocated for the low-performance
interfaces has already been extensively tested in previous versions of
this driver.
We also added the capability to log function calls by adding DEBUG flag.
Please note that this flag is commented out because this is the default
state
for it.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add mark and space parity, since the device supports it.
Signed-off-by: Roland Koebler <r.koebler@yahoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the vendor and device id for the Mobilcom Debitel UMTS surf
stick (a.k.a. 4G Systems XSStick W14, MobiData MBD-200HU, ...).
To see these ids, you need to switch the stick to modem operation first
with the help of usb_modeswitch. This makes it switch from 1c9e:f000 to
1c9e:9603 and thus be recognized by the option driver.
Signed-off-by: Gernot Hillier <gernot@hillier.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write. On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.
If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be
switched to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
The MessageContent for usb_modeswitch.conf is:
"55534243e0c26a85000000000000061b000000020000000000000000000000"
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=29a68e39d4a broke carrier handling so that a
cp210x setup which needed the carrier lines set up (non CLOCAL) which did
not make a call which set the termios bits left the lines down even if
CLOCAL was not asserted.
Fix this not by reverting but by adding the proper dtr_rts and
carrier_raised methods. This both sets the modem lines properly and also
implements the correct blocking semantics for the port as required by
POSIX.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Tested-by: Karl Hiramoto <karl@hiramoto.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch presents fixes for the autosuspend feature implementation in
sierra usb serial driver in functions sierra_open(), sierra_close() and
stop_read_write_urbs().
The patch "sierra_close() must resume the device before it notifies it
of a closure" submitted by Oliver Neukum on Wed, October 14 has been
merged as fix in sierra_close() function.
The bug fix in sierra_open() function restores the autopm interface
state on error condition.
The bug fix in in stop_read_write_urbs() function assures that both
receive and interrupt urbs are recycled.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch presents a fix for the autosuspend feature implementation in
sierra usb serial driver for function sierra_send_setup(). Because it
is possible to call sierra_send_setup() before sierra_open() or after
sierra_close() we added a get/put interface activity to assure that the
usb control can happen even when the device is autosuspended.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Tested-by: Matthew Safar <msafar@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch for Airplus MCD 650 card
Note: This device is with Victor V Kudlak, and he confirmed that this
device works with the patch.
Signed-off-by: Huzaifa Sidhpurwala <sidhpurwala.huzaifa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb:usbserial:visor: fix race between unthrottle and completion handler
visor_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.
the same bug as opticon.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
many serial subdrivers are clearly written as if throttle/unthrottle
cannot sleep. This leads to unneeded atomic submissions. This
patch converts affected drivers in a way to makes very clear that
throttle/unthrottle can sleep. Thus future misdesigns can be avoided
and efficiency and reliability improved.
This removes any such assumption using GFP_KERNEL and spin_lock_irq()
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb:usbserial:symbolserial: fix race between unthrottle and completion handler
symbol_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.
the same bug as opticon.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb:usbserial:opticon: fix race between unthrottle and completion handler
opticon_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb:usbserial: fix flags in error case of suspension
suspended flag must be reset in error case
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb:usbserial:visor: fix accounting in error case
data not pushed to the tty layer due to an error mustn't be counted
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The generic usbserial driver in Linux 2.6.31 halts its receiving
channel in response to throttle requests from the line discipline.
Unfortunately it drops the contents of the first URB received after
throttling takes effect. This patch corrects that problem.
Signed-off-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Acked-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the Dell inspiron mini 10, the GPS is connected via a cp2102. This patch
adds detection of this USB device. (I haven't managed to use the GPS under
Linux yet, though)
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1293) fixes a problem with the ipaq serial driver. It
tries to bind to all the interfaces, even those that don't have enough
endpoints. The symptom is an invalid memory reference and oops when
the device is plugged in.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable <stable@kernel.org>
Tested-by: Matthias Geissert <geissert@mathematik.tu-darmstadt.de>
Tested-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updated sierra driver version from 1.3.7 to 1.3.8 now that the autosuspend
capabilities were added to the driver.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1295) fixes a recently-added bug in the USB serial core.
If certain kinds of errors occur during probing, the core may call a
serial driver's release method without previously calling the attach
method. This causes some drivers (io_ti in particular) to perform an
invalid memory access.
The patch adds a new flag to keep track of whether or not attach has
been called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jean-Denis Girard <jd.girard@sysnux.pf>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a regression introduced in
39892da44b.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Re-structure read processing.
- Kill obsolete work queue and always push to tty in completion handler.
- Use tty_insert_flip_string instead of per character push when
possible.
- Fix stalled-read regression in 2.6.31 by using urb status to
determine when port is closed rather than port count.
- Fix race with open/close by checking ASYNCB_INITIALIZED in
unthrottle.
- Kill private rx_flag and lock and use throttle flags in
usb_serial_port instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove superfluous error checks in completion handler:
- No need to check private data and urb pointers as we check urb-status
before dereferencing priv (which is not freed until urb has been killed
on close).
- No need to check tty as it is checked again when processing.
- No need to check urb->number_of_packets on bulk urb.
Note that both private data and tty are checked again before processing
(possibly from work queue which also is cancelled on close).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove unused rx_byte counter which is never exposed as noted by Alan
Cox.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes tty_flip_buffer_push being called from hard interrupt context with
low_latency set.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following commit made console open fails while booting:
commit b50989dc44
Author: Alan Cox <alan@linux.intel.com>
Date: Sat Sep 19 13:13:22 2009 -0700
tty: make the kref destructor occur asynchronously
Due to tty release routines run in a workqueue now, error like the
following will be reported while booting:
INIT open /dev/console Input/output error
It also causes hibernation regression to appear as reported at
http://bugzilla.kernel.org/show_bug.cgi?id=14229
The reason is that now there's latency issue with closing, but when
we open a "closing not finished" tty, -EIO will be returned.
Fix it as per the following Alan's suggestion:
Fun but it's actually not a bug and the fix is wrong in itself as
the port may be closing but not yet being destructed, in which case
it seems to do the wrong thing. Opening a tty that is closing (and
could be closing for long periods) is supposed to return -EIO.
I suspect a better way to deal with this and keep the old console
timing is to split tty->shutdown into two functions.
tty->shutdown() - called synchronously just before we dump the tty
onto the waitqueue for destruction
tty->cleanup() - called when the destructor runs.
We would then do the shutdown part which can occur in IRQ context
fine, before queueing the rest of the release (from tty->magic = 0
... the end) to occur asynchronously
The USB update in -next would then need a call like
if (tty->cleanup)
tty->cleanup(tty);
at the top of the async function and the USB shutdown to be split
between shutdown and cleanup as the USB resource cleanup and final
tidy cannot occur synchronously as it needs to sleep.
In other words the logic becomes
final kref put
make object unfindable
async
clean it up
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
[ rjw: Rebased on top of 2.6.31-git, reworked the changelog. ]
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
[ Changed serial naming to match new rules, dropped tty_shutdown as per
comments from Alan Stern - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/usb/serial/sierra.c: In function 'sierra_suspend':
drivers/usb/serial/sierra.c:936: error: 'struct usb_device' has no member named 'auto_pm'
Repairs
commit e6929a9020
Author: Oliver Neukum <oliver@neukum.org>
Date: Fri Sep 4 23:19:53 2009 +0200
USB: support for autosuspend in sierra while online
Cc: Greg KH <greg@kroah.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This implements support for autosuspend in the sierra driver while online.
Remote wakeup is used for reception. Transmission is facilitated with a queue
and the asynchronous autopm mechanism. To prevent races a private flag
for opened ports and a counter of running transmissions needs to be added.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Tested-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is how "real" UARTs (e.g. 16550) work and AFAIK what RS232 specifies, too.
Make the driver more compliant.
Signed-off-by: Frank Schaefer <schaefer.frank@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device supports it, so why not use it ? Works fine !
Signed-off-by: Frank Schaefer <schaefer.frank@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the datasheets, the PL2303 supports a set of 25 baudrates.
The baudrate is set as a 4 byte value directly.
During my experiments with device 067b:2303 (PL2303X), I noticed that
- the bridge-controller always uses 9600 baud if invalid/unsupported baud rate
values are set
- the baud rate value returned by usb_control_msg(..., GET_LINE_REQUEST, ...)
does not reflect the actually used baudrate. Always the last set value is
returned, even if it was invalid and not used by the controller.
This patch fixes the following issues with the current code:
1.) make sure that only supported baudrates are set (are there any buggy
chip revisions out there which don't "like" other values... ?).
2.) always set the baudrate to the next nearest supported baudrate.
3.) applications can now read back the resulting baudrate properly, because
tty_encode_baud_rate(...) is now fed with the actually used baudrate.
Signed-off-by: Frank Schaefer <schaefer.frank@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using the module parameter vcc_default, you can choose the default VCC value.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
You can now set the IUU reader to 3.3V VCC instead of 5V VCC, using the sysfs
parameter vcc_mode. Valid values are 3 and 5.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michael Wileczka