Add new check for MIC. Do the internal DMIC as the Front MIC.
It could solve the default record source index issue.
[Fix the check properly using the bitmask by tiwai]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add an error message to snd_hda_add_nid() for invalid mapping NID to make
easier to hunt the buggy code.
Also added a missing space to the error message in snd_hda_build_controls()
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will save ~15ms boot time.
The first 10ms sleep was introduced in commit d2595d86e5 for (buggy)
Cxt codecs, so better to limit the sleep to the problem hardware.
For the second 10ms sleep, the HDA spec says:
Power State[1:0]:
00: Node Power state (D0) is fully on.
01: Node Power state (D1) allows for (does not require) the lowest possible power consuming state from which it
can return to the "fully on" state (D0) within 10 ms, excepting analog pass through circuits (e.g., CD analog
playback) which must remain fully on.
10: Node Power state (D2) allows for (does not require) the lowest possible power consuming state from which it
can return to the "fully on" state (D0) within 10 ms. For modems, this is the "wake on ring" power state.
11: Node Power state (D3) allows for (does not require) lowest possible power consuming state under software
control. Note that any low power state set by software must retain sufficient operational capability to properly
respond to subsequent software Power State command.
So 10ms is actually the max wait time. It should be safe to
remove/reduce it and rely on the loop of 1ms-sleeps.
CC: Marc Boucher <marc@linuxant.com>
CC: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a common helper function for clearing pin controls before suspend.
Use the pincfg array instead of looking through all widget tree.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Analog Device codecs seem to have problems with the triggering of
pin-sensing although their pincaps give the trigger requirements.
Some reported that constant CPU load on HP laptops with AD codecs.
For avoiding this regression, add a flag to codec struct to notify
explicitly that the codec doesn't suppot the trigger at pin-sensing.
Tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Postpone the mixer name setup after the codec patch since the codec
patch may change the codec name string in itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the wrong implementation of NID <-> kctl mapping for capture mixers
introduced by the ocmmit 5b0cb1d850.
So far, the driver returns an error at probe.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDA_SUBDEV_NID_FLAG is duplicate for amplifier control elements. Move
get_amp_nid_() call to the snd_hda_ctl_add() function.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The purpose of this changeset is to show information about amplifier
setting in the codec proc file. Something like:
Control: name="Front Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Control: name="Front Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=2, ofs=0
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This set of changes add missing NID values to some static control
elemenents. Also, it handles all "Capture Source" or "Input Source"
controls.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds support for dynamically created controls to proc codec file
(Control: lines).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is an initial patch to show universal control<->NID assigment in
proc codec file. The change helps to debug codec related problems.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Original implementation was keeping registered input device for SND_BEEP
and SND_TONE events all time. This patch changes this behaviour:
If digital PC Beep is turned off using universal control switch,
the input device is unregistered.
Explanation: The kd_mksound() send SND_BEEP and SND_TONE only to last
registered device acceping those events. It means that the HDA Intel
audio driver blocks also the internal PC Speaker device (pcspkr.c
driver) even if the HDA Beep is muted. The user can easy disable
all beeps using 'setterm -blength 0' or 'xset b off' command.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the power on/off counter and expose via sysfs files.
The sysfs files, power_on_acct and power_off_acct, are created under
each codec hwdep sysfs directory (e.g. /sys/class/sound/hwC0D0).
The files show the msec length of the codec power-on and power-off,
respectively.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add reboot notifier to each codec so that it can do some workarounds
needed for reboot.
So far, patch_sigmatel.c calls its shutup routine for avoiding noises
at reboot on some HP machines.
References: Novell bnc#544779
http://bugzilla.novell.com/show_bug.cgi?id=544779
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new Intel HDMI codec supports 2 independant HDMI/DisplayPort pipes.
We'll be exporting them as 2 pcm devices. So bump up the allowed number
of HDMI devices.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This unifies the code and data structure,
and makes it easy to add more HDMI devices.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently we hit a bug in our dev board, whose HDMI codec#3 may emit
redundant/spurious responses, which were then taken as responses to
command for another onboard Realtek codec#2, and mess up both codecs.
Extend the azx_rb.cmds and azx_rb.res to array and track each codec's
commands/responses separately. This helps keep good codec safe from
broken ones.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Volume-knob widgets may have connections even if they have no CONN_LIST
cap bit. Allow the query exceptionally in snd_hda_get_connections().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a check to snd_hda_get_connections() routine for
presence of AC_WCAP_CONN_LIST. Also, make sure that negative error
codes from noted route are handled on all places as errors.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add some tricks to reduce the click noise at powering down to D3
in the power saving mode on STAC/IDT codecs.
The key seems to be to reset PINs before the power-down, and some
delay before entering D3. The needed delay is significantly long,
but I don't know why.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To prevent "Too many connections" message and the error path for some HDMI
codecs (which makes onboard audio unusable), check for invalid zero
connections for CONNECT_LIST verb.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The newly added sanity-check for a codec verb can be better written
with logical ORs. Also, the parameter can be more than 8bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A recent bug involves passing auto detected >0x7f NID to codec command,
creating an invalid codec addr field, and finally lead to cmd timeout
and fall back into single command mode. Jaroslav fixed that bug in
alc880_parse_auto_config().
It would be safer to further check the bounds of all cmd fields.
Cc: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The codec read errors in snd_hda_get_connections() are ignored so far,
and it causes a problem like the bug in the commit
9d30937acc
ALSA: hda_intel: more strict alc880_parse_auto_config dig_nid checking
Better to check errors in the function and returns a proper error code
rather than passing bogus NID values.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When FLOAT PCM format is available but together with other linear
PCM formats, don't override maxbps value. For FLOAT format, it's always
32, thus it can be better checked in snd_hda_calc_stream_format().
Otherwise the maxbps 32 might be used wrongly even if the linear PCM
doesn't support it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check whether formats and rates don't result in zero due to the
restriction of SPDIF sharing. If any of them can be zero, disable
the SPDIF sharing mode instead. Otherwise it will lead to a PCM
configuration error.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, the FLOAT PCM format is used only exclusivley set. But
this can be a combination with other formats.
This patch changes the parser to allow the FLOAT format in addition
to other PCM formats.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The codec setup call via snd_hda_codec_configure() isn't necessarily
called in snd_hda_codec_new(). For the later added feature, it's better
to change the code flow like:
- create all codec instances
- configure each codec
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The reset of a BUS controller during operations is somehow risky and
shouldn't be done inevitably for devices that have apparently no such
codec-communication problems.
This patch adds the check of the hardware and limits the bus-reset
capability.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai