John W. Linville says:
====================
pull request: wireless 2014-09-05
Please pull this batch of fixes intended for the 3.17 stream...
For the mac80211 bits, Johannes says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
For the iwlwifi bits, Emmanuel says:
"I revert a patch that disabled CTS to self in dvm because users
reported issues. The revert is CCed to stable since the offending
patch was sent to stable too. I also bump the firmware API versions
since a new firmware is coming up. On top of that, Marcel fixes a
bug I introduced while fixing a bug in our Kconfig file."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As the management counters reach a threshold they will generate an
interrupt so the value can be saved and the counter reset. The
current code does not enable this interrupt on all counters. This
can result in inaccurate statistics.
Update the code to enable all the counters to generate an interrupt
when its threshold is exceeded.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the management counters are configured to be 32 bit register
values, the [rt]xoctetcount_gb and [rt]xoctetcount_g counters are
always 64 bit counter registers. Since they are not being treated as
64 bit values, these statistics are being reported incorrectly (ifconfig,
ethtool, etc.).
Update the routines used to read the registers to access the "hi"
register (an offset of 4 from the "lo" register) to create a 64 bit
value for these 64 bit counters.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does not affect the 10/100 GRETH MAC.
Before all GBit GRETH TX descriptor ring cleaning was done in
start_xmit(), when descriptor list became full it activated
TX interrupt to start the NAPI rx poll function to do TX ring
cleaning.
With this patch the TX descriptor ring is always cleaned from
the NAPI rx poll function, triggered via TX or RX interrupt.
Otherwise we could end up in TX frames being sent but not
reported to the stack being sent. On the 10/100 GRETH this
is not an issue since the SKB is copied&aligned into private
buffers so that the SKB can be freed directly on start_xmit()
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cnic module needs to ensure that if ipv6 support is compiled as a module,
then the cnic module cannot be compiled as built-in as it depends on ipv6.
Made this check cleaner via Kconfig
Use simpler IS_ENABLED for CONFIG_VLAN_8021Q check
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 1G SFP RJ45 module is detected, driver must reset the Tx laser
in order to prevent link issues. As part of change, the link_attr_sync
was relocated from vars to params.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are use less, and may generate compiling warnings, so remove them
(microblaze, arc, arm64, and unicore32 have already defined PCI_IOBASE).
The related warnings (with allmodconfig under microblaze):
CC [M] drivers/net/fddi/skfp/skfddi.o
In file included from drivers/net/fddi/skfp/skfddi.c:95:0:
drivers/net/fddi/skfp/h/skfbi.h:151:0: warning: "PCI_IOBASE" redefined
#define PCI_IOBASE 0xffffff00L /* Bit 31..8: I/O Base address */
^
In file included from include/linux/io.h:22:0,
from include/linux/pci.h:31,
from drivers/net/fddi/skfp/skfddi.c:82:
./arch/microblaze/include/asm/io.h:33:0: note: this is the location of the previous definition
#define PCI_IOBASE ((void __iomem *)_IO_BASE)
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should check if the map of the table actually succeeds, and also free
resources accordingly.
Version bumped to 1.2.1.0
Acked-by: Shelley Gong <shelleygong@vmware.com>
Acked-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
During allocation and initialization of the network driver structures,
the wrong pointer is used to initialize a spin lock. Fix the spin lock
initialization by using the proper pointer.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hosts can be both little and big endian.
In certain scenarios a big endian kernel can kexec a little endian kernel.
This patch fixes this case from both ends:
1) Return endianity to original values on shutdown (in case little endian kernel boots after we shutdown).
2) Do not rely on HW reset values when loading driver in little endian kernel
but configure them explicitly (in case previous kernel was big endian and did not reset the HW).
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calxeda 1G/10G XGMAC Ethernet support should be available only on
Calxeda ECX-1000/2000 (Highbank/Midway) platforms.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas SuperH Ethernet support should be available only on
Renesas ARM SoCs and SuperH architecture.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link is already up, the following sequence makes the kernel
block completely:
ip link set dev eth0 down
ip link set dev eth0 up
This is because on suspended phy, the following lines
__lpc_eth_reset(pldat);
__lpc_eth_init(pldat);
make the LPC ethernet core block (see LPC32x0 manual). The PHY needs to be
(re-)activated low-level first.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes race conditions between PCI error recovery callbacks and
potential ifup/ifdown.
First, if ifup (tg3_open) is called between tg3_io_error_detected() and
tg3_io_resume() then tp->timer is armed twice before expiry. Once during
tg3_open() and again during tg3_io_resume(). This results in BUG
at kernel/time/timer.c:945.
Second, if ifdown (tg3_close) is called between tg3_io_error_detected()
and tg3_io_resume() then tg3_napi_disable() is called twice without
a tg3_napi_enable between. Once during tg3_io_error_detected() and again
during tg3_close(). The tg3_io_resume() then hangs on rtnl_lock().
v2: Added logging messages per Prashant's request
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of RDMA-related called to t4_query_params() were issuing mbox commands
on mbox0 instead of mbox4.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid dumping MPS_RPLC_MAP_CTL for reg dumps; this is a Write-Only register.
Reading this register may cause MPS TCAM corruption.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adapter firmware can indicate error conditions to the host.
If the firmware has indicated an error, print out the reason for
the firmware error.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes few register access for both T4 and T5.
PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS & PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS
is T4 only register don't let T5 access them. For T5 MA_PARITY_ERROR_STATUS2
is additionally read. MPS_TRC_RSS_CONTROL is T4 only register, for T5 use
MPS_T5_TRC_RSS_CONTROL.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously it was using the length value of serial number.
Also added macro for VPD unique identifier (0x82).
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously assumed that a Port's Capabilities and Advertised Capabilities
would never change from Port Initialization time. This is no longer true
when we can have 10Gb/s and 1Gb/s SFP+ Transceiver Modules randomly swapped.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of the HW is not able to do the receive checksum offloading
the only feature to remove is NETIF_F_RXCSUM.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For new GMACs it is possible to turn-on/off the COE.
In the current driver, when disabled the Rx-checksum
via ethtool, the tool reported that csum was disabled
but the HW continued to set the IPC. Indeed this is
because the fix_features allows this. So the patch
fixes this problem by adding the set_features.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring Tx flow control the Rx queue count was used instead of
the Tx queue count for looping through the Tx hardware queues. Fix the
code to use the Tx queue count.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debugfs support for the xpcs registers did not properly use the
specified mmd (xpcs_mmd entry) which resulted in the default mmd
value always being used. Update the debugfs support to generate the
proper mmd register value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fifo size reported by the hardware is not correct. Add support
to limit the reported size to what is actually present. Also, fix
the argument types used in the fifo size calculation function.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flushing of the Tx hardware queues is only supported at a certain
level of the hardware. Retrieve the current version of the hardware
and use that to determine if flushing is supported.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `xgene_enet_delete_ring':
xgene_enet_main.c:(.text+0x28755a): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `xgene_enet_setup_tx_desc':
xgene_enet_main.c:(.text+0x287774): undefined reference to `dma_map_single'
xgene_enet_main.c:(.text+0x287780): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `xgene_enet_tx_completion':
xgene_enet_main.c:(.text+0x2878e6): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `xgene_enet_refill_bufpool':
xgene_enet_main.c:(.text+0x2879d4): undefined reference to `dma_map_single'
xgene_enet_main.c:(.text+0x2879e0): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `xgene_enet_rx_frame':
xgene_enet_main.c:(.text+0x287aaa): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `xgene_enet_free_desc_ring':
xgene_enet_main.c:(.text+0x287f98): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `xgene_enet_create_desc_ring':
xgene_enet_main.c:(.text+0x28808e): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `xgene_enet_probe':
xgene_enet_main.c:(.text+0x2883d4): undefined reference to `dma_set_mask'
xgene_enet_main.c:(.text+0x2883ec): undefined reference to `dma_supported'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-08-28
Please pull this batch of fixes intended for the 3.17 stream.
For the Bluetooth/6LowPAN/802.15.4 bits, Johan says:
'It contains a connection reference counting fix for LE where a
connection might stay up even though it should get disconnected.
The other 802.15.4 6LoWPAN related patches were sent to the bluetooth
tree by Alexander Aring and described as follows by him:
"
these patches contains patches for the bluetooth branch.
This series includes memory leak fixes and an errno value fix.
Also there are two patches for sending and receiving 1280 6LoWPAN
packets, which makes the IEEE 802.15.4 6LoWPAN stack more RFC
compliant.
"'
Along with that...
Alexey Khoroshilov fixes a use-after-free bug on at76c50x-usb.
Hauke Mehrtens adds a PCI ID to bcma.
Himangi Saraogi fixes a silly "A || A" test in rtlwifi.
Larry Finger adds a device ID to rtl8192cu.
Maks Naumov fixes a strncmp argument in ath9k.
Álvaro Fernández Rojas adds a PCI ID to ssb.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of PLS is active the PLS (PHY Link Status) bit in
the Reg12 has to be set to allow the MAC to asserts the LPI
pattern when the link is ok.
Signed-off-by: nandini sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to skip the EEE initialisation when the stmmac
is using a switch (with a fixed phy support).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value for LPI TW timer has to be updated to 0x1E that is the hardcoded value
of 20.5us and it will apply to all EEE enabled Remote PHYs.
Disadvantage is for PHY's that support lesser wakeup time but we can accept it
waiting to implement LLDP to negotiate the Wakeup time of Remote PHY.
Signed-off-by: nandini sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the definition of macros for EEE otherwise the LPI TX/RX
entry/exit cannot be properly managed.
Signed-off-by: Nandini Sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_IWLDVM and CONFIG_IWLMVM currently have a
"depends on m" as its requirement forcing it to be build
as module. This is not needed and thus just remove it.
Fixes: ae7486a2b7 ("iwlwifi: fix Kconfig issues")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
[Squashed 2 commites for MVM and DVM]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Move the function which we use to set VXLAN DMFS (flow-steering) rules
from mlx4_en to mlx4_core. This refactoring will allow the mlx4_ib driver
to call the helper for the use case of user-space RAW Ethernet QPs, such
that they can serve VXLAN traffic too.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling DMA_API_DEBUG, warnings are reported at runtime
because the device driver frees DMA memory with wrong functions
and it does not call dma_mapping_error after mapping dma memory.
The first problem is fixed by of introducing a flag that helps us
keeping track which mapping technique was used, so that we can use
the right API for unmap.
This approach was inspired by the e1000 driver, which uses a similar
technique.
Signed-off-by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Denis Kirjanov <kda@linux-powerpc.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP reference clock, used for setting the addend in the Timestamp Addend
Register, was erroneously hard-coded (as reported in the databook just as
example).
The patch removes the macro named: STMMAC_SYSCLOCK and allows to use a
reference clock (clk_ptp_ref_i) that can be passed from the platform.
If not passed, the main driver clock will be used as default; note that
this can be fine on some platforms.
Note that, prior this patch, using the old STMMAC_SYSCLOCK on some platforms,
as side effect, the ptp clock can move faster/slower than the system clock.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix a typo on mmc rx crc error when reported by ethtool.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to w/a a problem that happens on some boxes when run at 10Mbps
Half duplex mode.
During the transmission the CSR signal is asserted for some time and the frames
aborted because of carrier sense error.
This is reported by MMC HW counter: txcarrier signal.
This actually is a false carrier so the frames are good and there is no reason
to ask for dropping them.
This patch so disables the Carrier Sense During Transmission
and this means that the MAC transmitter ignore the CRS signal
during frame transmission in Half-Duplex mode.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Std 802.3az if the EEE Adv (Reg 7.60), Link partner ability
(Reg 7.61) and EEE capability (Register 3.20) bits return 0 this means no EEE
is supported. So this patch fixes the checks inside the phy_init_eee function.
Signed-off-by: Nandini Sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/marvell/mvneta.c: In function 'mvneta_skb_tx_csum':
drivers/net/ethernet/marvell/mvneta.c:1374:3: error: implicit declaration of function 'vlan_get_protocol' [-Werror=implicit-function-declaration]
__be16 l3_proto = vlan_get_protocol(skb);
^
Reporeted-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupt is enabled when bind_interdomain_evtchn_to_irqhandler returns.
If there's interrupt pending interrupt handler is invoked.
NAPI needs to be initialised before binding interrupt otherwise the
interrupt handler will try to scheduling a NAPI instance that is not
initialised yet, resulting in kernel OOPS.
This fixes a regression introduced in ea2c5e13 ("xen-netback: move NAPI
add/remove calls").
Ideally function calls to create kthreads should also be moved before
binding but I intent to fix this regression with minimal changes and
refactor the code with another patch.
Reported-by: Thomas Leonard <talex5@gmail.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO support for vlans. It also allows a user to
control vlan acceleration offloading. As such, it is possible to turn
off vlan acceleration and configure a vlan which will continue to send
TSO traffic.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information.
This results in corrupted frames sent on the wire.
This patch extracts the protocol value correctly by using a
vlan_get_protocol() helper and corrects corrupt TSO frames.
CC: Shahed Shaikh <shahed.shaikh@qlogic.com>
CC: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
CC: Ron Mercer <ron.mercer@qlogic.com>
CC: linux-driver@qlogic.com
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver doesn't appear to support vlan acceleration at
all. However, it does claim to support TSO and IP checksums
for vlan devices. Thus any configured vlan device would
end up passing down partial checksums or TSO frames.
The driver also uses the value from skb->protocol to
determine TSO and checksum offload information, but assumes
that skb->protocol holds the l3 protocol information.
As a result, vlan traffic with partial checksums or TSO
will fail those checks and TSO will not happen.
Fix this by using vlan_get_protocol() helper.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.
Fix this by using vlan_get_protocol() helper.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.
Fix this by using vlan_get_protocol() helper.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver claims that it can do TSO and IP checksums on vlan
devices and also allows user to control vlan acceleration offloading.
This makes it possible to push traffic to this driver that has TSO or
partial checksums set, but also have a non-accelearted vlan
header. In this case, the driver will fail to correctly
identify such traffic and will not correctly perform
segmentation and checksum calculation.
Fix this by using vlan_get_protocol() helper instead of
assuming skb->protocol always has this information.
CC: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller