"plat_id" is always non-NULL here. There is a zero element on the end
of the m25p_ids[] array and if we hit the end of the loop then plat_id
points to that.
This would lead to a NULL pointer dereference later on in the function.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is just a cleanup, it doesn't fix any bugs.
These functions all check retlen inconsistently and it generates a
warning in Smatch (http://smatch.sf.net). If retlen were ever NULL it
would cause an oops and the code has been this way since 2006 so someone
would have complained. Also I looked at other places that implemented
the mtd read and write functions and they dereference retlen without
checking.
I removed the checks.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
spi_write_then_read() may return its own return codes (e.g. -EIO),
so let's propagate the value down to the probe().
Also, remove jedec == 0 check, it isn't needed as nowadays we use
dedicated SPI device IDs for non-JEDEC flashes.
Suggested-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since commit 18c6182bae ("Rework
probing/JEDEC code"), m25p80 driver successfully registers chips
even if JEDEC probing fails.
This was needed to support non-JEDEC flashes. Though, it appears
that some platforms (e.g. blackfin bf533 stamp[1]) used the old
behavior to detect if there's any flash connected, so the driver
have to fail on JEDEC probing errors.
This patch restores the old behavior for JEDEC flashes, and adds
"-nonjedec" SPI device IDs for M25Pxx flashes, so that the kernel
still supports non-JEDEC flashes.
[1] http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=5975
Reported-by: Mingquan Pan
Reported-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for Macronix 25L8005. Tested on a HP t5325 Thin Client.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The rest of the function assumes that "data" can be null. I don't know
the code well enough to say whether it can actually be null, but there
is no harm in checking here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some SPI masters (ep93xx) have limitations when using the SFRMOUT
signal for the spi device chip select. The SFRMOUT signal is
only asserted as long as the spi transmit fifo contains data. As
soon as the last bit is clocked into the receive fifo it gets
deasserted.
The functions sst25l_status and sst25l_match_device use the API
function spi_write_then_read to write a command to the flash then
read the response back. This API function creates a two part spi
message for the write then read. When this message is transferred
the SFRMOUT signal ends up getting deasserted after the command
phase. This causes the command to get aborted by the device so
the read phase returns invalid data.
By changing sst25l_status and sst25l_match_device to use a single
transfer synchronous message, the SFRMOUT signal stays asserted
during the entire message so the correct data always gets returned.
This change will have no effect on SPI masters which use a chip
select mechanism (GPIO's, etc.) which does stay asserted correctly.
As a bonus, the single transfer synchronous messages complete faster
than multi-part messages.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All the SST25L series flash parts have uniform erase sectors. Remove
the extra MTD_DEBUG_LEVEL2 messages showing the eraseregions info
since they could never be shown.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
kasprintf combines kmalloc and sprintf, and takes care of the size
calculation itself.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression a,flag;
expression list args;
statement S;
@@
a =
- \(kmalloc\|kzalloc\)(...,flag)
+ kasprintf(flag,args)
<... when != a
if (a == NULL || ...) S
...>
- sprintf(a,args);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cosmetic fix: the path in the Makefile is wrong
Signed-off-by: Matteo Croce <matteo@teknoraver.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MAX_MTD_DEVICES is about to be removed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (90 commits)
jffs2: Fix long-standing bug with symlink garbage collection.
mtd: OneNAND: Fix test of unsigned in onenand_otp_walk()
mtd: cfi_cmdset_0002, fix lock imbalance
Revert "mtd: move mxcnd_remove to .exit.text"
mtd: m25p80: add support for Macronix MX25L4005A
kmsg_dump: fix build for CONFIG_PRINTK=n
mtd: nandsim: add support for 4KiB pages
mtd: mtdoops: refactor as a kmsg_dumper
mtd: mtdoops: make record size configurable
mtd: mtdoops: limit the maximum mtd partition size
mtd: mtdoops: keep track of used/unused pages in an array
mtd: mtdoops: several minor cleanups
core: Add kernel message dumper to call on oopses and panics
mtd: add ARM pismo support
mtd: pxa3xx_nand: Fix PIO data transfer
mtd: nand: fix multi-chip suspend problem
mtd: add support for switching old SST chips into QRY mode
mtd: fix M29W800D dev_id and uaddr
mtd: don't use PF_MEMALLOC
mtd: Add bad block table overrides to Davinci NAND driver
...
Fixed up conflicts (mostly trivial) in
drivers/mtd/devices/m25p80.c
drivers/mtd/maps/pcmciamtd.c
drivers/mtd/nand/pxa3xx_nand.c
kernel/printk.c
CAT25 chips (as manufactured by On Semiconductor, previously Catalyst
Semiconductor) are similar to the original M25Px0 chips, except:
- Address width can vary (1-2 bytes, in contrast to 3 bytes in M25P
chips). So, implement convenient m25p_addr2cmd() and m25p_cmdsz()
calls, and place address width information into flash_info struct;
- Page size can vary, therefore we shouldn't hardcode it, so get rid
of FLASH_PAGESIZE definition, and place the page size information
into flash_info struct;
- CAT25 EEPROMs don't need to be erased, so add NO_ERASE flag, and
propagate it to the mtd subsystem.
[dwmw2: Fix up for conflicts with DMA safety patch]
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Previosly the driver always tried JEDEC probing, assuming that non-JEDEC
chips will return '0'. But truly non-JEDEC chips (like CAT25) won't do
that, their behaviour on RDID command is undefined, so the driver should
not call jedec_probe() for these chips.
Also, be less strict on error conditions, don't fail to probe if JEDEC
found a chip that is different from what platform code told, instead
just print some warnings and use an information obtained via JEDEC. In
that case we should not trust partitions any longer, but they might be
still useful (i.e. they could protect some parts of the chip).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch converts the m25p80 driver so that now it uses .id_table
for device matching, making it properly detect devices on OpenFirmware
platforms (prior to this patch the driver misdetected non-JEDEC chips,
seeing all chips as "m25p80").
Also, now jedec_probe() only does jedec probing, nothing else. If it
is not able to detect a chip, NULL is returned and the driver fall
backs to the information specified by the platform (platform_data, or
exact ID).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
spi_write() requires the buffer to be DMA-safe, kmalloc()
it seperately to ensure this.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix a potential memory leak in mtd_dataflash driver.
The private data that is allocated when registering a DataFlash
device with the MTD subsystem is not released if an error occurs
when add_mtd_partitions() or add_mtd_device() is called. Fix this
by adding an error path. The memory is already released during a
remove.
Also, add a dev_set_drvdata(&spi->dev, NULL) before the kfree() so
that the spi device does not reference invalid data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
The SST SPI flashes is like Atmel SPI flashes in that the software
protection bits are set by default at power up, so clear them at init
time.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (58 commits)
mtd: jedec_probe: add PSD4256G6V id
mtd: OneNand support for Nomadik 8815 SoC (on NHK8815 board)
mtd: nand: driver for Nomadik 8815 SoC (on NHK8815 board)
m25p80: Add Spansion S25FL129P serial flashes
jffs2: Use SLAB_HWCACHE_ALIGN for jffs2_raw_{dirent,inode} slabs
mtd: sh_flctl: register sh_flctl using platform_driver_probe()
mtd: nand: txx9ndfmc: transfer 512 byte at a time if possible
mtd: nand: fix tmio_nand ecc correction
mtd: nand: add __nand_correct_data helper function
mtd: cfi_cmdset_0002: add 0xFF intolerance for M29W128G
mtd: inftl: fix fold chain block number
mtd: jedec: fix compilation problem with I28F640C3B definition
mtd: nand: fix ECC Correction bug for SMC ordering for NDFC driver
mtd: ofpart: Check availability of reg property instead of name property
driver/Makefile: Initialize "mtd" and "spi" before "net"
mtd: omap: adding DMA mode support in nand prefetch/post-write
mtd: omap: add support for nand prefetch-read and post-write
mtd: add nand support for w90p910 (v2)
mtd: maps: add mtd-ram support to physmap_of
mtd: pxa3xx_nand: add single-bit error corrections reporting
...
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions to the following modules from drivers/mtd/
devices/m25p80.c
devices/slram.c
linux version 2.6.30
ftl.c
nand/cafe_nand.c
nand/cmx270_nand.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The error handling in the phram driver is pretty bad -- in many places,
errors are silently ignored or logged, but then still ignored in the
return value. So convert all of the code to pass back the correct return
value and log error messages properly (and using the new pr_fmt() helper).
If everything does go smoothly, rather than exit silently, dump a helpful
info message like pretty much every other MTD driver does.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Joern Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Support SST25WF{512,010,020,040} SPI flashes.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The SST SPI flashes are a bit non-standard in that they can be programmed
one byte at a time (including address!), or they can be written two bytes
at a time with auto address incrementing (AAI). The latter form is
obviously much better for performance, so let's use it when possible.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add an omitted unlock to one sst25l_erase fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for the non JEDEC SST25L SPI Flash devices.
[dwmw2: Some cleanups]
Signed-off-by: Andre Renaud <andre@bluewatersys.com>
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: "H Hartley Sweeten" <hartleys@visionengravers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the misspelling to match the actual config variable defined in
drivers/mtd/devi ces/Kconfig:
config MTD_DATAFLASH_WRITE_VERIFY
bool "Verify DataFlash page writes"
depends on MTD_DATAFLASH
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The m25p16 data sheet from numonyx lists the worst-case bulk erase time
(tBE) as 40 seconds.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (63 commits)
mtd: OneNAND: Allow setting of boundary information when built as module
jffs2: leaking jffs2_summary in function jffs2_scan_medium
mtd: nand: Fix memory leak on txx9ndfmc probe failure.
mtd: orion_nand: use burst reads with double word accesses
mtd/nand: s3c6400 support for s3c2410 driver
[MTD] [NAND] S3C2410: Use DIV_ROUND_UP
[MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
[MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
[MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
mtd: physmap_of: Add multiple regions and concatenation support
mtd: nand: max_retries off by one in mxc_nand
mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
mtd: Flex-OneNAND support
mtd: nand: add OMAP2/OMAP3 NAND driver
mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
mtd: uclinux: mark local stuff static
mtd: uclinux: do not allow to be built as a module
mtd: uclinux: allow systems to override map addr/size
mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
...
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
this patch add m45pe10 [1] chip support to the m25p80 driver.
[1] http://www.numonyx.com/Documents/Datasheets/M45PE10.pdf
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 5b7f3a50 (fix dataflash 64-bit divisions) unfortunately
introduced a typo. Erase addr and len were swapped in the pageaddr
calculation, causing the wrong sectors to get erased.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter