The only effect of this patch is to print a warning if IFLA_LINKMODE is updated
and a following change fails.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only effect of this patch is to print a warning if IFLA_TXQLEN is updated
and a following change fails.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the exported IPv4 NAT functions that are provided by the core. This
removes duplicated code so iptables and nft use the same NAT codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Move the specific NAT IPv4 core functions that are called from the
hooks from iptable_nat.c to nf_nat_l3proto_ipv4.c. This prepares the
ground to allow iptables and nft to use the same NAT engine code that
comes in a follow up patch.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
sk->sk_error_queue is dequeued in four locations. All share the
exact same logic. Deduplicate.
Also collapse the two critical sections for dequeue (at the top of
the recv handler) and signal (at the bottom).
This moves signal generation for the next packet forward, which should
be harmless.
It also changes the behavior if the recv handler exits early with an
error. Previously, a signal for follow-up packets on the errqueue
would then not be scheduled. The new behavior, to always signal, is
arguably a bug fix.
For rxrpc, the change causes the same function to be called repeatedly
for each queued packet (because the recv handler == sk_error_report).
It is likely that all packets will fail for the same reason (e.g.,
memory exhaustion).
This code runs without sk_lock held, so it is not safe to trust that
sk->sk_err is immutable inbetween releasing q->lock and the subsequent
test. Introduce int err just to avoid this potential race.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_checksum_try_convert and skb_gro_checksum_try_convert
after checksum is found present and validated in the GRE header
for normal and GRO paths respectively.
In GRO path, call skb_gro_checksum_try_convert
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for doing CHECKSUM_UNNECESSARY to CHECKSUM_COMPLETE
conversion in UDP tunneling path.
In the normal UDP path, we call skb_checksum_try_convert after locating
the UDP socket. The check is that checksum conversion is enabled for
the socket (new flag in UDP socket) and that checksum field is
non-zero.
In the UDP GRO path, we call skb_gro_checksum_try_convert after
checksum is validated and checksum field is non-zero. Since this is
already in GRO we assume that checksum conversion is always wanted.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This flag indicates that an invalid checksum was detected in the
packet. __skb_mark_checksum_bad helper function was added to set this.
Checksums can be marked bad from a driver or the GRO path (the latter
is implemented in this patch). csum_bad is checked in
__skb_checksum_validate_complete (i.e. calling that when ip_summed ==
CHECKSUM_NONE).
csum_bad works in conjunction with ip_summed value. In the case that
ip_summed is CHECKSUM_NONE and csum_bad is set, this implies that the
first (or next) checksum encountered in the packet is bad. When
ip_summed is CHECKSUM_UNNECESSARY, the first checksum after the last
one validated is bad. For example, if ip_summed == CHECKSUM_UNNECESSARY,
csum_level == 1, and csum_bad is set-- then the third checksum in the
packet is bad. In the normal path, the packet will be dropped when
processing the protocol layer of the bad checksum:
__skb_decr_checksum_unnecessary called twice for the good checksums
changing ip_summed to CHECKSUM_NONE so that
__skb_checksum_validate_complete is called to validate the third
checksum and that will fail since csum_bad is set.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/dsa/dsa.c:624:20: sparse: symbol 'dsa_pack_type' was not declared.
Should it be static?
Fixes: 3e8a72d1da ("net: dsa: reduce number of protocol hooks")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix places where there is space before tab, long lines, and
awkward if(){, double spacing etc. Add blank line after declaration/initialization.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-08-28
Please pull this batch of fixes intended for the 3.17 stream.
For the Bluetooth/6LowPAN/802.15.4 bits, Johan says:
'It contains a connection reference counting fix for LE where a
connection might stay up even though it should get disconnected.
The other 802.15.4 6LoWPAN related patches were sent to the bluetooth
tree by Alexander Aring and described as follows by him:
"
these patches contains patches for the bluetooth branch.
This series includes memory leak fixes and an errno value fix.
Also there are two patches for sending and receiving 1280 6LoWPAN
packets, which makes the IEEE 802.15.4 6LoWPAN stack more RFC
compliant.
"'
Along with that...
Alexey Khoroshilov fixes a use-after-free bug on at76c50x-usb.
Hauke Mehrtens adds a PCI ID to bcma.
Himangi Saraogi fixes a silly "A || A" test in rtlwifi.
Larry Finger adds a device ID to rtl8192cu.
Maks Naumov fixes a strncmp argument in ath9k.
Álvaro Fernández Rojas adds a PCI ID to ssb.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Then testing the TX limits of the stack, then it is useful to
be-able to disable the do_gettimeofday() timetamping on every packet.
This implements a pktgen flag NO_TIMESTAMP which will disable this
call to do_gettimeofday().
The performance change on (my system E5-2695) with skb_clone=0, goes
from TX 2,423,751 pps to 2,567,165 pps with flag NO_TIMESTAMP. Thus,
the cost of do_gettimeofday() or saving is approx 23 nanosec.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC name table updates are distributed asynchronously in a cluster,
entailing a risk of certain race conditions. E.g., if two nodes
simultaneously issue conflicting (overlapping) publications, this may
not be detected until both publications have reached a third node, in
which case one of the publications will be silently dropped on that
node. Hence, we end up with an inconsistent name table.
In most cases this conflict is just a temporary race, e.g., one
node is issuing a publication under the assumption that a previous,
conflicting, publication has already been withdrawn by the other node.
However, because of the (rtt related) distributed update delay, this
may not yet hold true on all nodes. The symptom of this failure is a
syslog message: "tipc: Cannot publish {%u,%u,%u}, overlap error".
In this commit we add a resiliency queue at the receiving end of
the name table distributor. When insertion of an arriving publication
fails, we retain it in this queue for a short amount of time, assuming
that another update will arrive very soon and clear the conflict. If so
happens, we insert the publication, otherwise we drop it.
The (configurable) retention value defaults to 2000 ms. Knowing from
experience that the situation described above is extremely rare, there
is no risk that the queue will accumulate any large number of items.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to perform the same actions when processing deferred name
table updates, so this functionality is moved to a separate
function.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just maintain the list properly by returning the head of the remaining
SKB list from dev_hard_start_xmit().
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_hard_start_xmit() does two things, it first validates and
canonicalizes the SKB, then it actually sends it.
Make a set of helper functions for doing the first part.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a slight policy change happening here as well.
The previous code would drop the entire rest of the GSO skb if any of
them got, for example, a congestion notification.
That makes no sense, anything NET_XMIT_MASK and below is something
like congestion or policing. And in the congestion case it doesn't
even mean the packet was actually dropped.
Just continue until dev_xmit_complete() evaluates to false.
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_NETFILTER_XT_TARGET_LOG is not selected anymore when jumping
from 3.16 to 3.17-rc1 if you don't set on the new NF_LOG_IPV4 and
NF_LOG_IPV6 switches.
Change this to select the three new symbols NF_LOG_COMMON, NF_LOG_IPV4
and NF_LOG_IPV6 instead, so NETFILTER_XT_TARGET_LOG remains enabled
when moving from old to new kernels.
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CHECKSUM_UNNECESSARY may be applied to the SCTP CRC so we need to
appropriate account for this by decrementing csum_level. This is
done by calling __skb_dec_checksum_unnecessary.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow GRO path to "consume" checksums provided in CHECKSUM_UNNECESSARY
and to report new checksums verfied for use in fallback to normal
path.
Change GRO checksum path to track csum_level using a csum_cnt field
in NAPI_GRO_CB. On GRO initialization, if ip_summed is
CHECKSUM_UNNECESSARY set NAPI_GRO_CB(skb)->csum_cnt to
skb->csum_level + 1. For each checksum verified, decrement
NAPI_GRO_CB(skb)->csum_cnt while its greater than zero. If a checksum
is verfied and NAPI_GRO_CB(skb)->csum_cnt == 0, we have verified a
deeper checksum than originally indicated in skbuf so increment
csum_level (or initialize to CHECKSUM_UNNECESSARY if ip_summed is
CHECKSUM_NONE or CHECKSUM_COMPLETE).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch:
- Clarifies the specific requirements of devices returning
CHECKSUM_UNNECESSARY (comments in skbuff.h).
- Adds csum_level field to skbuff. This is used to express how
many checksums are covered by CHECKSUM_UNNECESSARY (stores n - 1).
This replaces the overloading of skb->encapsulation, that field is
is now only used to indicate inner headers are valid.
- Change __skb_checksum_validate_needed to "consume" each checksum
as indicated by csum_level as layers of the the packet are parsed.
- Remove skb_pop_rcv_encapsulation, no longer needed in the new
csum_level model.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since SCTP day 1, that is, 19b55a2af145 ("Initial commit") from lksctp
tree, the official <netinet/sctp.h> header carries a copy of enum
sctp_sstat_state that looks like (compared to the current in-kernel
enumeration):
User definition: Kernel definition:
enum sctp_sstat_state { typedef enum {
SCTP_EMPTY = 0, <removed>
SCTP_CLOSED = 1, SCTP_STATE_CLOSED = 0,
SCTP_COOKIE_WAIT = 2, SCTP_STATE_COOKIE_WAIT = 1,
SCTP_COOKIE_ECHOED = 3, SCTP_STATE_COOKIE_ECHOED = 2,
SCTP_ESTABLISHED = 4, SCTP_STATE_ESTABLISHED = 3,
SCTP_SHUTDOWN_PENDING = 5, SCTP_STATE_SHUTDOWN_PENDING = 4,
SCTP_SHUTDOWN_SENT = 6, SCTP_STATE_SHUTDOWN_SENT = 5,
SCTP_SHUTDOWN_RECEIVED = 7, SCTP_STATE_SHUTDOWN_RECEIVED = 6,
SCTP_SHUTDOWN_ACK_SENT = 8, SCTP_STATE_SHUTDOWN_ACK_SENT = 7,
}; } sctp_state_t;
This header was later on also placed into the uapi, so that user space
programs can compile without having <netinet/sctp.h>, but the shipped
with <linux/sctp.h> instead.
While RFC6458 under 8.2.1.Association Status (SCTP_STATUS) says that
sstat_state can range from SCTP_CLOSED to SCTP_SHUTDOWN_ACK_SENT, we
nevertheless have a what it appears to be dummy SCTP_EMPTY state from
the very early days.
While it seems to do just nothing, commit 0b8f9e25b0 ("sctp: remove
completely unsed EMPTY state") did the right thing and removed this dead
code. That however, causes an off-by-one when the user asks the SCTP
stack via SCTP_STATUS API and checks for the current socket state thus
yielding possibly undefined behaviour in applications as they expect
the kernel to tell the right thing.
The enumeration had to be changed however as based on the current socket
state, we access a function pointer lookup-table through this. Therefore,
I think the best way to deal with this is just to add a helper function
sctp_assoc_to_state() to encapsulate the off-by-one quirk.
Reported-by: Tristan Su <sooqing@gmail.com>
Fixes: 0b8f9e25b0 ("sctp: remove completely unsed EMPTY state")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit ed98df3361 ("net: use __GFP_NORETRY for high order
allocations") we tried to address one issue caused by order-3
allocations.
We still observe high latencies and system overhead in situations where
compaction is not successful.
Instead of trying order-3, order-2, and order-1, do a single order-3
best effort and immediately fallback to plain order-0.
This mimics slub strategy to fallback to slab min order if the high
order allocation used for performance failed.
Order-3 allocations give a performance boost only if they can be done
without recurring and expensive memory scan.
Quoting David :
The page allocator relies on synchronous (sync light) memory compaction
after direct reclaim for allocations that don't retry and deferred
compaction doesn't work with this strategy because the allocation order
is always decreasing from the previous failed attempt.
This means sync light compaction will always be encountered if memory
cannot be defragmented or reclaimed several times during the
skb_page_frag_refill() iteration.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6c9808ce09 ("tipc: remove port_lock") accidentally involves
a potential bug: when tipc socket instance(tsk) is not got with given
reference number in tipc_sk_get(), tsk is set to NULL. Subsequently
we jump to exit label where to decrease socket reference counter
pointed by tsk pointer in tipc_sk_put(). However, As now tsk is NULL,
oops may happen because of touching a NULL pointer.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace occurences of skb_get_queue_mapping() and follow-up
netdev_get_tx_queue() with an actual helper function.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds one more ACPI ID of a Broadcom bluetooth chip.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a device driver is unloaded local->interfaces
list is cleared. If there was more than 1
interface running and connected (bound to a
chanctx) then chantype recalc was called and it
ended up with compat being NULL causing a call
trace warning.
Warn if compat becomes NULL as a result of
incompatible bss_conf.chandef of interfaces bound
to a given channel context only.
The call trace looked like this:
WARNING: CPU: 2 PID: 2594 at /devel/src/linux/net/mac80211/chan.c:557 ieee80211_recalc_chanctx_chantype+0x2cd/0x2e0()
Modules linked in: ath10k_pci(-) ath10k_core ath
CPU: 2 PID: 2594 Comm: rmmod Tainted: G W 3.16.0-rc1+ #150
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
0000000000000009 ffff88001ea279c0 ffffffff818dfa93 0000000000000000
ffff88001ea279f8 ffffffff810514a8 ffff88001ce09cd0 ffff88001e03cc58
0000000000000000 ffff88001ce08840 ffff88001ce09cd0 ffff88001ea27a08
Call Trace:
[<ffffffff818dfa93>] dump_stack+0x4d/0x66
[<ffffffff810514a8>] warn_slowpath_common+0x78/0xa0
[<ffffffff81051585>] warn_slowpath_null+0x15/0x20
[<ffffffff818a407d>] ieee80211_recalc_chanctx_chantype+0x2cd/0x2e0
[<ffffffff818a3dda>] ? ieee80211_recalc_chanctx_chantype+0x2a/0x2e0
[<ffffffff818a4919>] ieee80211_assign_vif_chanctx+0x1a9/0x770
[<ffffffff818a6220>] __ieee80211_vif_release_channel+0x70/0x130
[<ffffffff818a6dd3>] ieee80211_vif_release_channel+0x43/0xb0
[<ffffffff81885f4e>] ieee80211_stop_ap+0x21e/0x5a0
[<ffffffff8184b9b5>] __cfg80211_stop_ap+0x85/0x520
[<ffffffff8181c188>] __cfg80211_leave+0x68/0x120
[<ffffffff8181c268>] cfg80211_leave+0x28/0x40
[<ffffffff8181c5f3>] cfg80211_netdev_notifier_call+0x373/0x6b0
[<ffffffff8107f965>] notifier_call_chain+0x55/0x110
[<ffffffff8107fa41>] raw_notifier_call_chain+0x11/0x20
[<ffffffff816a8dc0>] call_netdevice_notifiers_info+0x30/0x60
[<ffffffff816a8eb9>] __dev_close_many+0x59/0xf0
[<ffffffff816a9021>] dev_close_many+0x81/0x120
[<ffffffff816aa1c5>] rollback_registered_many+0x115/0x2a0
[<ffffffff816aa3a6>] unregister_netdevice_many+0x16/0xa0
[<ffffffff8187d841>] ieee80211_remove_interfaces+0x121/0x1b0
[<ffffffff8185e0e6>] ieee80211_unregister_hw+0x56/0x110
[<ffffffffa0011ac4>] ath10k_mac_unregister+0x14/0x60 [ath10k_core]
[<ffffffffa0014fe7>] ath10k_core_unregister+0x27/0x40 [ath10k_core]
[<ffffffffa003b1f4>] ath10k_pci_remove+0x44/0xa0 [ath10k_pci]
[<ffffffff81373138>] pci_device_remove+0x28/0x60
[<ffffffff814cb534>] __device_release_driver+0x64/0xd0
[<ffffffff814cbcc8>] driver_detach+0xb8/0xc0
[<ffffffff814cb23a>] bus_remove_driver+0x4a/0xb0
[<ffffffff814cc697>] driver_unregister+0x27/0x50
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the Broadcom Starfigther 2 switch chip using a DSA
driver. This switch driver supports the following features:
- configuration of the external switch port interface: MII, RevMII,
RGMII and RGMII_NO_ID are supported
- support for the per-port MIB counters
- support for link interrupts for special ports (e.g: MoCA)
- powering up/down of switch memories to conserve power when ports are
unused
Finally, update the compatible property for the DSA core code to match
our switch top-level compatible node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the 4-bytes Broadcom tag that built-in switches such as
the Starfighter 2 might insert when receiving packets, or that we need
to insert while targetting specific switch ports. We use a fake local
EtherType value for this 4-bytes switch tag: ETH_P_BRCMTAG to make sure
we can assign DSA-specific network operations within the DSA drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switch drivers to hook a PHY link update callback to perform
port-specific link work.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever libphy determines that the link status of a given PHY/port has
changed, allow to call into the switch driver link adjustment callback
so proper actions can be taken care of by the switch driver upon link
notification.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case switch port tagging is disabled (voluntarily, or the switch just
does not support it), allow us to continue using the defined set of
dsa_device_ops in net/dsa/slave.c.
We introduce dsa_protocol_is_tagged() to check whether we need to
override skb->protocol and go through the DSA-specifif packet_type
function, or if we just go on and receive the SKB through the normal
path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the DSA slave interface to be bound to an arbitray PHY, not just
the ones that are available as child PHY devices of the switch MDIO bus.
This allows us for instance to have external PHYs connected to a
separate MDIO bus, but yet also connected to a given switch port.
Under certain configurations, the physical port mask might not be a 1:1
mapping to the MII PHYs mask. This is the case, if e.g: Port 1 of the
switch is used and connects to a PHY at a MDIO address different than 1.
Introduce a phys_mii_mask variable which allows driver to implement and
divert their own MDIO read/writes operations for a subset of the MDIO
PHY addresses.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will later use the per-port device_node pointer to fetch a bunch of
port-specific properties.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We might need to fetch additional resources from the device tree node
pointer, such as register ranges or other properties. Keep a device_node
pointer around for this.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA is currently registering one packet_type function per EtherType it
needs to intercept in the receive path of a DSA-enabled Ethernet device.
Right now we have three of them: trailer, DSA and eDSA, and there might
be more in the future, this will not scale to the addition of new
protocols.
This patch proceeds with adding a new layer of abstraction and two new
functions:
dsa_switch_rcv() which will dispatch into the tag-protocol specific
receive function implemented by net/dsa/tag_*.c
dsa_slave_xmit() which will dispatch into the tag-protocol specific
transmit function implemented by net/dsa/tag_*.c
When we do create the per-port slave network devices, we iterate over
the switch protocol to assign the DSA-specific receive and transmit
operations.
A new fake ethertype value is used: ETH_P_XDSA to illustrate the fact
that this is no longer going to look like ETH_P_DSA or ETH_P_TRAILER
like it used to be.
This allows us to greatly simplify the check in eth_type_trans() and
always override the skb->protocol with ETH_P_XDSA for Ethernet switches
tagged protocol, while also reducing the number repetitive slave
netdevice_ops assignments.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit fc60476761
("ipvs: changes for local real server") from 2.6.37
introduced DNAT support to local real server but the
IPv6 LOCAL_OUT handler ip_vs_local_reply6() is
registered incorrectly as IPv4 hook causing any outgoing
IPv4 traffic to be dropped depending on the IP header values.
Chris tracked down the problem to CONFIG_IP_VS_IPV6=y
Bug report: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1349768
Reported-by: Chris J Arges <chris.j.arges@canonical.com>
Tested-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The "rcu_dereference()" calls are used directly in conditions.
Since their return values are never dereferenced it is recommended to
use "rcu_access_pointer()" instead of "rcu_dereference()".
Therefore, this patch makes the replacements.
The following Coccinelle semantic patch was used:
@@
@@
(
if(
(<+...
- rcu_dereference
+ rcu_access_pointer
(...)
...+>)) {...}
|
while(
(<+...
- rcu_dereference
+ rcu_access_pointer
(...)
...+>)) {...}
)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The tunneling method should properly use tunnel encapsulation.
Fixes problem with CHECKSUM_PARTIAL packets when TCP/UDP csum
offload is supported.
Thanks to Alex Gartrell for reporting the problem, providing
solution and for all suggestions.
Reported-by: Alex Gartrell <agartrell@fb.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
You can use this to skip accounting objects when listing/resetting
via NFNL_MSG_ACCT_GET/NFNL_MSG_ACCT_GET_CTRZERO messages with the
NLM_F_DUMP netlink flag. The filtering covers the following cases:
1. No filter specified. In this case, the client will get old behaviour,
2. List/reset counter object only: In this case, you have to use
NFACCT_F_QUOTA as mask and value 0.
3. List/reset quota objects only: You have to use NFACCT_F_QUOTA_PKTS
as mask and value - the same, for byte based quota mask should be
NFACCT_F_QUOTA_BYTES and value - the same.
If you want to obtain the object with any quota type
(ie. NFACCT_F_QUOTA_PKTS|NFACCT_F_QUOTA_BYTES), you need to perform
two dump requests, one to obtain NFACCT_F_QUOTA_PKTS objects and
another for NFACCT_F_QUOTA_BYTES.
Signed-off-by: Alexey Perevalov <a.perevalov@samsung.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using the cfg80211_inform_bss[_width]() functions drivers
cannot currently indicate whether the data was received in a
beacon or probe response. Fix that by passing a new enum that
indicates such (or unknown).
For good measure, use it in ath6kl.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Arend van Spriel <arend@broadcom.com> [brcmfmac]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few possible cases of where BSS data came from:
1) only a beacon has been received
2) only a probe response has been received
3) the driver didn't report what it received (this happens when
using cfg80211_inform_bss[_width]())
4) both probe response and beacon data has been received
Unfortunately, in the userspace API, a few things weren't there:
a) there was no way to differentiate cases 1) and 4) above
without comparing the data of the IEs
b) the TSF was always from the last frame, instead of being
exposed for beacon/probe response separately like IEs
Fix this by
i) exporting a new flag attribute that indicates whether or
not probe response data has been received - this addresses (a)
ii) exporting a BEACON_TSF attribute that holds the beacon's TSF
if a beacon has been received
iii) not exporting the beacon attributes in case (3) above as that
would just lead userspace into thinking the data actually came
from a beacon when that isn't clear
To implement this, track inside the IEs struct whether or not it
(definitely) came from a beacon.
Reported-by: William Seto
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit dda444d524.
Channel switching code has been reworked and
improved significantly since the time original
locking issues were found.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Header-less cloned skbs with sufficient headroom need not be cloned
unless the tailroom is going to be modified.
Fix ieee80211_skb_resize so it would only resize cloned skbs if either
the header isn't released or the tailroom is going to be modified.
Some drivers might have assumed that skbs are never cloned, so add a HW
flag that explicitly permits cloned TX skbs. Drivers which do not modify
TX skbs should set this flag to avoid copying skbs.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When hw acceleration is enabled, the GENERATE_IV or PUT_IV_SPACE flags
will only require headroom space. Consequently, the tailroom-needed
counter can safely be decremented.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the cfg80211_rx_mgmt(), parameter @gfp was used for the memory allocation.
But, memory get allocated under spin_lock_bh(), this implies atomic context.
So, one can't use GFP_KERNEL, only variants with no __GFP_WAIT. Actually, in all
occurrences GFP_ATOMIC is used (wil6210 use GFP_KERNEL by mistake),
and it should be this way or warning triggered in the memory allocation code.
Remove @gfp parameter as no actual choice exist, and use hard coded
GFP_ATOMIC for memory allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "RX active" string is too long, so the columns get
shifted. Change it to just "RX" to avoid this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sta->last_seq_ctrl is the seq_ctrl field from the last header
seen, need to shift it 4 bits to extract the sequence number.
Otherwise the ieee80211_sn_less() check at the top of
ieee80211_sta_manage_reorder_buf drops frames until the sequence
number catches up.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Denton Gentry <denton.gentry@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 802.11 standard says when processing a plink confirm
frame:
"If the peerLinkID in the mesh peering instance has not been
set, the Local Link ID field of the Mesh Peering Confirm
request shall be copied into the peerLinkID in the mesh
peering instance."
We were only doing this when receiving an open peering frame,
but it could happen that the open frame gets lost and so we
should handle this case rather than rejecting the confirm and
failing the whole peering process.
Reported-by: Yu Niiro <yu.niiro@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_sta_ps_deliver_wakeup, sdata->smps_mode is checked. This is
initialized only for the base AP interface, not the individual VLANs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When bringing down the AP, a WARN_ON is hit because the bss config chandef
is empty here.
Since AP_VLAN channel settings do not matter for anything chanctx related
(always inherits the settings from the AP interface), let's just ignore
it here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 24aa11ab8a.
That commit was wrong since it uses data that hasn't even been set
up yet, but might be a hold-over from a previous connection.
Additionally, it seems like a driver-specific workaround that
shouldn't have been in mac80211 to start with.
Cc: stable@vger.kernel.org
Fixes: 24aa11ab8a ("mac80211: disable uAPSD if all ACs are under ACM")
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is follow-up to
da08143b85 ("vlan: more careful checksum features handling")
which introduced more careful feature intersection in vlan code,
taking into account that HW_CSUM should be considered superset
of IP_CSUM/IPV6_CSUM. The same is needed in netif_skb_features()
in order to avoid offloading mismatch warning when vlan is
created on top of a bond consisting of slaves supporting IP/IPv6
checksumming but not vlan Tx offloading.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: commit 690e36e726 (net: Allow raw buffers to be passed into the flow dissector)
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: commit 690e36e726 (net: Allow raw buffers to be passed into the flow dissector)
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code manipulating sysfs symlinks on adjacent net_devices(s)
currently doesn't take into account that devices potentially
belong to different namespaces.
This patch trying to fix an issue as follows:
- check for net_ns before creating / deleting symlink.
for now only netdev_adjacent_rename_links and
__netdev_adjacent_dev_remove are affected, afaics
__netdev_adjacent_dev_insert implies both net_devs
belong to the same namespace.
- Drop all existing symlinks to / from all adj_devs before
switching namespace and recreate them just after.
Signed-off-by: Alexander Y. Fomichev <git.user@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it can send regulatory domain change notification before any
NEW_WIPHY notification. Moreover, if rfill_register() fails, calling
wiphy_unregister() will send a DEL_WIPHY though no NEW_WIPHY had been
sent previously.
Thus reordering so it properly notifies NEW_WIPHY before any other.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds one more ACPI ID of a Broadcom bluetooth chip.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use HAVE_JUMP_LABEL as elsewhere in the kernel to ensure
that the toolchain has the required support in addition to
CONFIG_JUMP_LABEL being set.
Signed-off-by: Zhouyi Zhou <yizhouzhou@ict.ac.cn>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch makes no changes to the logic of the code but simply addresses
coding style issues as detected by checkpatch.
Both objdump and diff -w show no differences.
This patch removes some blank lines between the end of a function
definition and the EXPORT_SYMBOL_GPL macro in order to prevent
checkpatch warning that EXPORT_SYMBOL must immediately follow
a function.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes no changes to the logic of the code but simply addresses
coding style issues as detected by checkpatch.
Both objdump and diff -w show no differences.
This patch addresses structure definitions, specifically it cleanses the brace
placement and replaces spaces with tabs in a few places.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes no changes to the logic of the code but simply addresses
coding style issues as detected by checkpatch.
Both objdump and diff -w show no differences.
A number of items are addressed in this patch:
* Multiple spaces converted to tabs
* Spaces before tabs removed.
* Spaces in pointer typing cleansed (char *)foo etc.
* Remove space after sizeof
* Ensure spacing around comparators such as if statements.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In GRE demux if the GRE checksum pop rcv encapsulation so that any
encapsulated checksums are treated as tunnel checksums.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement GRO for UDPv6. Add UDP checksum verification in gro_receive
for both UDP4 and UDP6 calling skb_gro_checksum_validate_zero_check.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tcp[64]_gro_receive call skb_gro_checksum_validate to validate TCP
checksum in the gro context.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add skb_gro_checksum_validate, skb_gro_checksum_validate_zero_check,
and skb_gro_checksum_simple_validate, and __skb_gro_checksum_complete.
These are the cognates of the normal checksum functions but are used
in the gro_receive path and operate on GRO related fields in sk_buffs.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter reported that the static checker emits the warning
net/netfilter/ipset/ip_set_list_set.c:600 init_list_set()
warn: integer overflows 'sizeof(*map) + size * set->dsize'
Limit the maximal number of elements in list type of sets.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Resolve missing-field-initializer warnings by providing a
directed initializer.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Ranges of values are broken with hash:net,net and hash:net,port,net.
hash:net,net
============
# ipset create test-nn hash:net,net
# ipset add test-nn 10.0.10.1-10.0.10.127,10.0.0.0/8
# ipset list test-nn
Name: test-nn
Type: hash:net,net
Revision: 0
Header: family inet hashsize 1024 maxelem 65536
Size in memory: 16960
References: 0
Members:
10.0.10.1,10.0.0.0/8
# ipset test test-nn 10.0.10.65,10.0.0.1
10.0.10.65,10.0.0.1 is NOT in set test-nn.
# ipset test test-nn 10.0.10.1,10.0.0.1
10.0.10.1,10.0.0.1 is in set test-nn.
hash:net,port,net
=================
# ipset create test-npn hash:net,port,net
# ipset add test-npn 10.0.10.1-10.0.10.127,tcp:80,10.0.0.0/8
# ipset list test-npn
Name: test-npn
Type: hash:net,port,net
Revision: 0
Header: family inet hashsize 1024 maxelem 65536
Size in memory: 17344
References: 0
Members:
10.0.10.8/29,tcp:80,10.0.0.0
10.0.10.16/28,tcp:80,10.0.0.0
10.0.10.2/31,tcp:80,10.0.0.0
10.0.10.64/26,tcp:80,10.0.0.0
10.0.10.32/27,tcp:80,10.0.0.0
10.0.10.4/30,tcp:80,10.0.0.0
10.0.10.1,tcp:80,10.0.0.0
# ipset list test-npn
# ipset test test-npn 10.0.10.126,tcp:80,10.0.0.2
10.0.10.126,tcp:80,10.0.0.2 is NOT in set test-npn.
# ipset test test-npn 10.0.10.126,tcp:80,10.0.0.0
10.0.10.126,tcp:80,10.0.0.0 is in set test-npn.
# ipset create test-npn hash:net,port,net
# ipset add test-npn 10.0.10.0/24,tcp:80-81,10.0.0.0/8
# ipset list test-npn
Name: test-npn
Type: hash:net,port,net
Revision: 0
Header: family inet hashsize 1024 maxelem 65536
Size in memory: 17024
References: 0
Members:
10.0.10.0,tcp:80,10.0.0.0
10.0.10.0,tcp:81,10.0.0.0
# ipset test test-npn 10.0.10.126,tcp:80,10.0.0.0
10.0.10.126,tcp:80,10.0.0.0 is NOT in set test-npn.
# ipset test test-npn 10.0.10.0,tcp:80,10.0.0.0
10.0.10.0,tcp:80,10.0.0.0 is in set test-npn.
Correctly setup from..to variables where no IPSET_ATTR_IP_TO{,2}
attribute is given, so in range processing loop we construct proper
cidr value. Check whenever we have no ranges and can short cut in
hash:net,net properly. Use unlikely() where appropriate, to comply
with other modules.
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Markmask is an u32, hence it can't be greater then 4294967295 ( i.e.
0xffffffff ). This was causing smatch warning:
net/netfilter/ipset/ip_set_hash_gen.h:1084 hash_ipmark_create() warn:
impossible condition '(markmask > 4294967295) => (0-u32max > u32max)'
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Add cpu support to meta expresion.
This allows you to match packets with cpu number.
Signed-off-by: Ana Rey <anarey@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add pkttype support for ip, ipv6 and inet families of tables.
This allows you to fetch the meta packet type based on the link layer
information. The loopback traffic is a special case, the packet type
is guessed from the network layer header.
No special handling for bridge and arp since we're not going to see
such traffic in the loopback interface.
Joint work with Alvaro Neira Ayuso <alvaroneay@gmail.com>
Signed-off-by: Alvaro Neira Ayuso <alvaroneay@gmail.com>
Signed-off-by: Ana Rey <anarey@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Replace open codings of (((u64) <x> * <y>) >> 32) with reciprocal_scale().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers, and perhaps other entities we have not yet considered,
sometimes want to know how deep the protocol headers go before
deciding how large of an SKB to allocate and how much of the packet to
place into the linear SKB area.
For example, consider a driver which has a device which DMAs into
pools of pages and then tells the driver where the data went in the
DMA descriptor(s). The driver can then build an SKB and reference
most of the data via SKB fragments (which are page/offset/length
triplets).
However at least some of the front of the packet should be placed into
the linear SKB area, which comes before the fragments, so that packet
processing can get at the headers efficiently. The first thing each
protocol layer is going to do is a "pskb_may_pull()" so we might as
well aggregate as much of this as possible while we're building the
SKB in the driver.
Part of supporting this is that we don't have an SKB yet, so we want
to be able to let the flow dissector operate on a raw buffer in order
to compute the offset of the end of the headers.
So now we have a __skb_flow_dissect() which takes an explicit data
pointer and length.
Signed-off-by: David S. Miller <davem@davemloft.net>
We complete the merging of the port and socket layer by aggregating
the fields of struct tipc_port directly into struct tipc_sock, and
moving the combined structure into socket.c.
We also move all functions and macros that are not any longer
exposed to the rest of the stack into socket.c, and rename them
accordingly.
Despite the size of this commit, there are no functional changes.
We have only made such changes that are necessary due of the removal
of struct tipc_port.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reference table is now 'socket aware' instead of being generic,
and has in reality become a socket internal table. In order to be
able to minimize the API exposed by the socket layer towards the rest
of the stack, we now move the reference table definitions and functions
into the file socket.c, and rename the functions accordingly.
There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move the inline functions in the file port.h to socket.c, and modify
their names accordingly.
We move struct tipc_port and some macros to socket.h.
Finally, we remove the file port.h.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this commit, we move the remaining functions in port.c to
socket.c, and give them new names that correspond to their new
location. We then remove the file port.c.
There are only cosmetic changes to the moved functions.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In previous commits we have reduced usage of port_lock to a minimum,
and complemented it with usage of bh_lock_sock() at the remaining
locations. The purpose has been to remove this lock altogether, since
it largely duplicates the role of bh_lock_sock. We are now ready to do
this.
However, we still need to protect the BH callers from inadvertent
release of the socket while they hold a reference to it. We do this by
replacing port_lock by a combination of a rw-lock protecting the
reference table as such, and updating the socket reference counter while
the socket is referenced from BH. This technique is more standard and
comprehensible than the previous approach, and turns out to have a
positive effect on overall performance.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make tipc_sock the only entity referencable from other
parts of the stack, we add a tipc_sock pointer instead of a tipc_port
pointer to the registry. As a consequence, we also let the function
tipc_port_lock() return a pointer to a tipc_sock instead of a tipc_port.
We keep the function's name for now, since the lock still is owned by
the port.
This is another step in the direction of eliminating port_lock, replacing
its usage with lock_sock() and bh_lock_sock().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions tipc_port_get_ports() and tipc_port_reinit() scan over
all sockets/ports to access each of them. This is done by using a
dedicated linked list, 'tipc_socks' where all sockets are members. The
list is in turn protected by a spinlock, 'port_list_lock', while each
socket is locked by using port_lock at the moment of access.
In order to reduce complexity and risk of deadlock, we want to get
rid of the linked list and the accompanying spinlock.
This is what we do in this commit. Instead of the linked list, we use
the port registry to scan across the sockets. We also add usage of
bh_lock_sock() inside the scope of port_lock in both functions, as a
preparation for the complete removal of port_lock.
Finally, we move the functions from port.c to socket.c, and rename them
to tipc_sk_sock_show() and tipc_sk_reinit() repectively.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the latest changes to the socket/port layer the existence of
the functions tipc_port_init() and tipc_port_destroy() cannot be
justified. They are both called only once, from tipc_sk_create() and
tipc_sk_delete() respectively, and their functionality can better be
merged into the latter two functions.
This also entails that all remaining references to port_lock now are
made from inside socket.c, something that will make it easier to remove
this lock.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_acknowledge() is a remnant from the obsolete native
API. Currently, it grabs port_lock, before building an acknowledge
message and sending it to the peer.
Since all access to socket members now is protected by the socket lock,
it has become unnecessary to grab port_lock here.
In this commit, we remove the usage of port_lock, simplify the
function, and move it to socket.c, renaming it to tipc_sk_send_ack().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_port_connect()/tipc_port_disconnect() are remnants of the obsolete
native API. Their only task is to grab port_lock and call the functions
__tipc_port_connect()/__tipc_port_disconnect() respectively, which will
perform the actual state change.
Since socket/port exection now is single-threaded the use of port_lock
is not needed any more, so we can safely replace the two functions with
their lock-free counterparts.
In this commit, we remove the two functions. Furthermore, the contents
of __tipc_port_disconnect() is so trivial that we choose to eliminate
that function too, expanding its functionality into tipc_shutdown().
__tipc_port_connect() is simplified, moved to socket.c, and given the
more correct name tipc_sk_finish_conn(). Finally, we eliminate the
function auto_connect(), and expand its contents into filter_connect().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_port_shutdown() is a remnant from the now obsolete native
interface. As such it grabs port_lock in order to protect itself
from concurrent BH processing.
However, after the recent changes to the port/socket upcalls, sockets
are now basically single-threaded, and all execution, except the read-only
tipc_sk_timer(), is executing within the protection of lock_sock(). So
the use of port_lock is not needed here.
In this commit we eliminate the whole function, and merge it into its
only caller, tipc_shutdown().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last remaining BH upcall to the socket, apart for the message
reception function tipc_sk_rcv(), is the timer function.
We prefer to let this function continue executing in BH, since it only
does read-acces to semi-permanent data, but we make three changes to it:
1) We introduce a bh_lock_sock()/bh_unlock_sock() inside the scope
of port_lock. This is a preparation for replacing port_lock with
bh_lock_sock() at the locations where it is still used.
2) We move the function from port.c to socket.c, as a further step
of eliminating the port code level altogether.
3) We let it make use of the newly introduced tipc_msg_create()
function. This enables us to get rid of three context specific
functions (port_create_self_abort_msg() etc.) in port.c
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current implementation, each 'struct tipc_node' instance keeps
a linked list of those ports/sockets that are connected to the node
represented by that struct. The purpose of this is to let the node
object know which sockets to alert when it loses contact with its peer
node, i.e., which sockets need to have their connections aborted.
This entails an unwanted direct reference from the node structure
back to the port/socket structure, and a need to grab port_lock
when we have to make an upcall to the port. We want to get rid of
this unecessary BH entry point into the socket, and also eliminate
its use of port_lock.
In this commit, we instead let the node struct keep list of "connected
socket" structs, which each represents a connected socket, but is
allocated independently by the node at the moment of connection. If
the node loses contact with its peer node, the list is traversed, and
a "connection abort" message is created for each entry in the list. The
message is sent to it respective connected socket using the ordinary
data path, and the receiving socket aborts its connections upon reception
of the message.
This enables us to get rid of the direct reference from 'struct node' to
´struct port', and another unwanted BH access point to the latter.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current link implementation keeps a linked list of blocked ports/
sockets that is populated when there is link congestion. The purpose
of this is to let the link know which users to wake up when the
congestion abates.
This adds unnecessary complexity to the data structure and the code,
since it forces us to involve the link each time we want to delete
a socket. It also forces us to grab the spinlock port_lock within
the scope of node_lock. We want to get rid of this direct dependence,
as well as the deadlock hazard resulting from the usage of port_lock.
In this commit, we instead let the link keep list of a "wakeup" pseudo
messages for use in such situations. Those messages are sent to the
pending sockets via the ordinary message reception path, and wake up
the socket's owner when they are received.
This enables us to get rid of the 'waiting_ports' linked lists in struct
tipc_port that manifest this direct reference. As a consequence, we can
eliminate another BH entry into the socket, and hence the need to grab
port_lock. This is a further step in our effort to remove port_lock
altogether.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_msg_init() has turned out to be of limited value
in many cases. It take too few parameters to be usable for creating
a complete message, it makes too many assumptions about what the
message should be used for, and it does not allocate any buffer to
be returned to the caller.
Therefore, we now introduce the new function tipc_msg_create(), which
takes all the parameters needed to create a full message, and returns
a buffer of the requested size. The new function will be very useful
for the changes we will be doing in later commits in this series.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon timeout, undo (via both timestamps/Eifel and DSACKs) was
disabled if any retransmits were still in flight. The concern was
perhaps that spurious retransmission sent in a previous recovery
episode may trigger DSACKs to falsely undo the current recovery.
However, this inadvertently misses undo opportunities (using either
TCP timestamps or DSACKs) when timeout occurs during a loss episode,
i.e. recurring timeouts or timeout during fast recovery. In these
cases some retransmissions will be in flight but we should allow
undo. Furthermore, we should only reset undo_marker and undo_retrans
upon timeout if we are starting a new recovery episode. Finally,
when we do reset our undo state, we now do so in a manner similar
to tcp_enter_recovery(), so that we require a DSACK for each of
the outstsanding retransmissions. This will achieve the original
goal by requiring that we receive the same number of DSACKs as
retransmissions.
This patch increases the undo events by 50% on Google servers.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a followup to commit 676d23690f ("net: Fix use after free by
removing length arg from sk_data_ready callbacks"), we can remove
some useless code in sock_queue_rcv_skb() and rxrpc_queue_rcv_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ktime_get_ns() replaces ktime_to_ns(ktime_get())
ktime_get_real_ns() replaces ktime_to_ns(ktime_get_real())
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new_ctx pointer is set only for non-chanctx drivers. This yielded a
crash for chanctx-based drivers during channel switch finalization:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
IP: ieee80211_vif_use_reserved_switch+0x71c/0xb00 [mac80211]
Use an adequate chanctx pointer to fix this.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.
A simplified version of the Coccinelle semantic patch making this change
is as follows:
@change@
expression E1,E2,E3;
@@
- jiffies - E1 >= (E2*E3)
+ time_after_eq(jiffies, E1+E2*E3)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.
A simplified version of the Coccinelle semantic patch making this change
is as follows:
@change@
expression E1,E2;
@@
- (jiffies - E1) >= E2
+ time_after_eq(jiffies, E1+E2)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.
A simplified version of the Coccinelle semantic patch making this change
is as follows:
@change@
expression E1,E2;
@@
- jiffies - E1 < E2
+ time_before(jiffies, E1+E2)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions time_before, time_before_eq, time_after, and time_after_eq
are more robust for comparing jiffies against other values.
A simplified version of the Coccinelle semantic patch making this change
is as follows:
@change@
expression E1,E2;
@@
(
- (jiffies - E1) < E2
+ time_before(jiffies, E1+E2)
)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "rcu_dereference()" call is used directly in a condition.
Since its return value is never dereferenced it is recommended to use
"rcu_access_pointer()" instead of "rcu_dereference()".
Therefore, this patch makes the replacement.
The following Coccinelle semantic patch was used:
@@
@@
(
if(
(<+...
- rcu_dereference
+ rcu_access_pointer
(...)
...+>)) {...}
|
while(
(<+...
- rcu_dereference
+ rcu_access_pointer
(...)
...+>)) {...}
)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "rcu_dereference()" call is used directly in a condition.
Since its return value is never dereferenced it is recommended to use
"rcu_access_pointer()" instead of "rcu_dereference()".
Therefore, this patch makes the replacement.
The following Coccinelle semantic patch was used:
@@
@@
(
if(
(<+...
- rcu_dereference
+ rcu_access_pointer
(...)
...+>)) {...}
|
while(
(<+...
- rcu_dereference
+ rcu_access_pointer
(...)
...+>)) {...}
)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7a9bc9b81a ("ipv4: Elide fib_validate_source() completely when possible.")
introduced a short-circuit to avoid calling fib_validate_source when not
needed. That change took rp_filter into account, but not accept_local.
This resulted in a change of behaviour: with rp_filter and accept_local
off, incoming packets with a local address in the source field should be
dropped.
Here is how to reproduce the change pre/post 7a9bc9b81a commit:
-configure the same IPv4 address on hosts A and B.
-try to send an ARP request from B to A.
-The ARP request will be dropped before that commit, but accepted and answered
after that commit.
This adds a check for ACCEPT_LOCAL, to maintain full
fib validation in case it is 0. We also leave __fib_validate_source() earlier
when possible, based on the same check as fib_validate_source(), once the
accept_local stuff is verified.
Cc: Gregory Detal <gregory.detal@uclouvain.be>
Cc: Christoph Paasch <christoph.paasch@uclouvain.be>
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Sébastien Barré <sebastien.barre@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SCTP, selection of active (T.ACT) and retransmission (T.RET)
transports is being done whenever transport control operations
(UP, DOWN, PF, ...) are engaged through sctp_assoc_control_transport().
Commits 4c47af4d5e ("net: sctp: rework multihoming retransmission
path selection to rfc4960") and a7288c4dd5 ("net: sctp: improve
sctp_select_active_and_retran_path selection") have both improved
it towards a more fine-grained and optimal path selection.
Currently, the selection algorithm for T.ACT and T.RET is as follows:
1) Elect the two most recently used ACTIVE transports T1, T2 for
T.ACT, T.RET, where T.ACT<-T1 and T1 is most recently used
2) In case primary path T.PRI not in {T1, T2} but ACTIVE, set
T.ACT<-T.PRI and T.RET<-T1
3) If only T1 is ACTIVE from the set, set T.ACT<-T1 and T.RET<-T1
4) If none is ACTIVE, set T.ACT<-best(T.PRI, T.RET, T3) where
T3 is the most recently used (if avail) in PF, set T.RET<-T.PRI
Prior to above commits, 4) was simply a camp on T.ACT<-T.PRI and
T.RET<-T.PRI, ignoring possible paths in PF. Camping on T.PRI is
still slightly suboptimal as it can lead to the following scenario:
Setup:
<A> <B>
T1: p1p1 (10.0.10.10) <==> .'`) <==> p1p1 (10.0.10.12) <= T.PRI
T2: p1p2 (10.0.10.20) <==> (_ . ) <==> p1p2 (10.0.10.22)
net.sctp.rto_min = 1000
net.sctp.path_max_retrans = 2
net.sctp.pf_retrans = 0
net.sctp.hb_interval = 1000
T.PRI is permanently down, T2 is put briefly into PF state (e.g. due to
link flapping). Here, the first time transmission is sent over PF path
T2 as it's the only non-INACTIVE path, but the retransmitted data-chunks
are sent over the INACTIVE path T1 (T.PRI), which is not good.
After the patch, it's choosing better transports in both cases by
modifying step 4):
4) If none is ACTIVE, set T.ACT_new<-best(T.ACT_old, T3) where T3 is
the most recently used (if avail) in PF, set T.RET<-T.ACT_new
This will still select a best possible path in PF if available (which
can also include T.PRI/T.RET), and set both T.ACT/T.RET to it.
In case sctp_assoc_control_transport() *just* put T.ACT_old into INACTIVE
as it transitioned from ACTIVE->PF->INACTIVE and stays in INACTIVE just
for a very short while before going back ACTIVE, it will guarantee that
this path will be reselected for T.ACT/T.RET since T3 (PF) is not
available.
Previously, this was not possible, as we would only select between T.PRI
and T.RET, and a possible T3 would be NULL due to the fact that we have
just transitioned T3 in sctp_assoc_control_transport() from PF->INACTIVE
and would select a suboptimal path when T.PRI/T.RET have worse properties.
In the case that T.ACT_old permanently went to INACTIVE during this
transition and there's no PF path available, plus T.PRI and T.RET are
INACTIVE as well, we would now camp on T.ACT_old, but if everything is
being INACTIVE there's really not much we can do except hoping for a
successful HB to bring one of the transports back up again and, thus
cause a new selection through sctp_assoc_control_transport().
Now both tests work fine:
Case 1:
1. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
2. T1 S(ACTIVE) T.ACT, T.RET
T2 S(PF)
3. T1 S(ACTIVE) T.ACT, T.RET
T2 S(INACTIVE)
5. T1 S(PF) T.ACT, T.RET
T2 S(INACTIVE)
[ 5.1 T1 S(INACTIVE) T.ACT, T.RET
T2 S(INACTIVE) ]
6. T1 S(ACTIVE) T.ACT, T.RET
T2 S(INACTIVE)
7. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
Case 2:
1. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
2. T1 S(PF)
T2 S(ACTIVE) T.ACT, T.RET
3. T1 S(INACTIVE)
T2 S(ACTIVE) T.ACT, T.RET
5. T1 S(INACTIVE)
T2 S(PF) T.ACT, T.RET
[ 5.1 T1 S(INACTIVE)
T2 S(INACTIVE) T.ACT, T.RET ]
6. T1 S(INACTIVE)
T2 S(ACTIVE) T.ACT, T.RET
7. T1 S(ACTIVE) T.ACT
T2 S(ACTIVE) T.RET
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both transports are the same, we don't have to go down that
road only to realize that we will return the very same transport.
We are guaranteed that curr is always non-NULL. Therefore, just
short-circuit this special case.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there are multiple vlan headers present in a received frame, the first
one is put into vlan_tci and protocol is set to ETH_P_8021Q. Anything in the
skb beyond the VLAN TPID may be still non-linear, including the inner TCI
and ethertype. While ovs_flow_extract takes care of IP and IPv6 headers, it
does nothing with ETH_P_8021Q. Later, if OVS_ACTION_ATTR_POP_VLAN is
executed, __pop_vlan_tci pulls the next vlan header into vlan_tci.
This leads to two things:
1. Part of the resulting ethernet header is in the non-linear part of the
skb. When eth_type_trans is called later as the result of
OVS_ACTION_ATTR_OUTPUT, kernel BUGs in __skb_pull. Also, __pop_vlan_tci
is in fact accessing random data when it reads past the TPID.
2. network_header points into the ethernet header instead of behind it.
mac_len is set to a wrong value (10), too.
Reported-by: Yulong Pei <ypei@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the transport has always been in state SCTP_UNCONFIRMED, it
therefore wasn't active before and hasn't been used before, and it
always has been, so it is unnecessary to bug the user with a
notification.
Reported-by: Deepak Khandelwal <khandelwal.deepak.1987@gmail.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Suggested-by: Michael Tuexen <tuexen@fh-muenster.de>
Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
af_packet can currently overwrite kernel memory by out of bound
accesses, because it assumed a [new] block can always hold one frame.
This is not generally the case, even if most existing tools do it right.
This patch clamps too long frames as API permits, and issue a one time
error on syslog.
[ 394.357639] tpacket_rcv: packet too big, clamped from 5042 to 3966. macoff=82
In this example, packet header tp_snaplen was set to 3966,
and tp_len was set to 5042 (skb->len)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: f6fb8f100b ("af-packet: TPACKET_V3 flexible buffer implementation.")
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LECS response contains the MTU that should be used. Correctly
synchronize with other layers when updating.
Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the LE passive scanning and auto-connections feature was
introduced. It uses the hci_connect_le() API which returns a hci_conn
along with a reference count to that object. All previous users would
tie this returned reference to some existing object, such as an L2CAP
channel, and there'd be no leaked references this way. For
auto-connections however the reference was returned but not stored
anywhere, leaving established connections with one higher reference
count than they should have.
Instead of playing special tricks with hci_conn_hold/drop this patch
associates the returned reference from hci_connect_le() with the object
that in practice does own this reference, i.e. the hci_conn_params
struct that caused us to initiate a connection in the first place. Once
the connection is established or fails to establish this reference is
removed appropriately.
One extra thing needed is to call hci_pend_le_actions_clear() before
calling hci_conn_hash_flush() so that the reference is cleared before
the hci_conn objects are fully removed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This enables the netfilter NAT engine in first place, otherwise
you cannot ever select the nf_tables nat expression if iptables
is not selected.
Reported-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There's actually no good reason why we cannot use cgroup id 0,
so lets just remove this artificial barrier.
Reported-by: Alexey Perevalov <a.perevalov@samsung.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Alexey Perevalov <a.perevalov@samsung.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now q->now_rt is identical to q->now and is not required anymore.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mainstream commit f0f6ee1f70 ("cbq: incorrect processing of high limits")
have side effect: if cbq bandwidth setting is less than real interface
throughput non-limited traffic can delay limited traffic for a very long time.
This happen because of q->now changes incorrectly in cbq_dequeue():
in described scenario L2T is much greater than real time delay,
and q->now gets an extra boost for each transmitted packet.
Accumulated boost prevents update q->now, and blocked class can wait
very long time until (q->now >= cl->undertime) will be true again.
To fix the problem the patch updates q->now on each cbq_update() call.
L2T-related pre-modification q->now was moved to cbq_update().
My testing confirmed that it fixes the problem and did not discover
any side-effects
Fixes: f0f6ee1f70 ("cbq: incorrect processing of high limits")
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch drops the userspace accessable sysfs entry for the maximum
datagram size of a 6LoWPAN fragment packet.
A fragment should not have a datagram size value greater than 1280 byte.
Instead of make this value configurable, we accept 1280 datagram size
fragment packets only.
Signed-off-by: Martin Townsend <martin.townsend@xsilon.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes the 1281 MTU to 1280. Others stack have only a 1280
byte array for uncompressed 6LoWPAN packets, this avoid that these
stacks have an overflow. Sending 1281 uncompressed 6LoWPAN packets isn't
also rfc complaint.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If received frame contains the reserved destination address mode. The
frame should be dropped and free the skb.
Signed-off-by: Martin Townsend <martin.townsend@xsilon.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch correct the return value of lowpan_alloc_frag if an error
occur. Errno numbers should always be negative.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix a memory leak if received frame was not able to parse.
Signed-off-by: Martin Townsend <martin.townsend@xsilon.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, the NAT configs depend on iptables and ip6tables. However,
users should be capable of enabling NAT for nft without having to
switch on iptables.
Fix this by adding new specific IP_NF_NAT and IP6_NF_NAT config
switches for iptables and ip6tables NAT support. I have also moved
the original NF_NAT_IPV4 and NF_NAT_IPV6 configs out of the scope
of iptables to make them independent of it.
This patch also adds NETFILTER_XT_NAT which selects the xt_nat
combo that provides snat/dnat for iptables. We cannot use NF_NAT
anymore since nf_tables can select this.
Reported-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit 3b4f302d85 ("tipc: eliminate
redundant locking") introduced a bug by removing the sanity check
for message importance, allowing programs to assign any value to
the msg_user field. This will mess up the packet reception logic
and may cause random link resets.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1d023284c3 ("list: fix order of arguments for
hlist_add_after(_rcu)") was incorrectly rebased on top of
d9124268d8 ("batman-adv: Fix out-of-order
fragmentation support"). The parameter order change of the rebased patch was
not re-applied as expected. This causes a memory leak and can cause crashes
when out-of-order packets are received. hlist_add_behind will try to access the
uninitalized list pointers of frag_entry_new to find the previous/next entry
and may modify/read random memory locations.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the AP only advertises support for 20MHz (in the
ht operation ie), disable 40MHz and VHT.
This can improve interoperability with APs that
don't like stations exceeding their own
advertised capabilities.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently track the QoS capability twice: for all peer stations
in the WLAN_STA_WME flag, and for any clients associated to an AP
interface separately for drivers in the sta->sta.wme field.
Remove the WLAN_STA_WME flag and track the capability only in the
driver-visible field, getting rid of the limitation that the field
is only valid in AP mode.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Silences the following sparse warnings:
net/netlink/af_netlink.c:2926:21: warning: context imbalance in 'netlink_seq_start' - wrong count at exit
net/netlink/af_netlink.c:2972:13: warning: context imbalance in 'netlink_seq_stop' - unexpected unlock
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix TCP FRTO logic so that it always notices when snd_una advances,
indicating that any RTO after that point will be a new and distinct
loss episode.
Previously there was a very specific sequence that could cause FRTO to
fail to notice a new loss episode had started:
(1) RTO timer fires, enter FRTO and retransmit packet 1 in write queue
(2) receiver ACKs packet 1
(3) FRTO sends 2 more packets
(4) RTO timer fires again (should start a new loss episode)
The problem was in step (3) above, where tcp_process_loss() returned
early (in the spot marked "Step 2.b"), so that it never got to the
logic to clear icsk_retransmits. Thus icsk_retransmits stayed
non-zero. Thus in step (4) tcp_enter_loss() would see the non-zero
icsk_retransmits, decide that this RTO is not a new episode, and
decide not to cut ssthresh and remember the current cwnd and ssthresh
for undo.
There were two main consequences to the bug that we have
observed. First, ssthresh was not decreased in step (4). Second, when
there was a series of such FRTO (1-4) sequences that happened to be
followed by an FRTO undo, we would restore the cwnd and ssthresh from
before the entire series started (instead of the cwnd and ssthresh
from before the most recent RTO). This could result in cwnd and
ssthresh being restored to values much bigger than the proper values.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Fixes: e33099f96d ("tcp: implement RFC5682 F-RTO")
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_tw_recycle heavily relies on tcp timestamps to build a per-host
ordering of incoming connections and teardowns without the need to
hold state on a specific quadruple for TCP_TIMEWAIT_LEN, but only for
the last measured RTO. To do so, we keep the last seen timestamp in a
per-host indexed data structure and verify if the incoming timestamp
in a connection request is strictly greater than the saved one during
last connection teardown. Thus we can verify later on that no old data
packets will be accepted by the new connection.
During moving a socket to time-wait state we already verify if timestamps
where seen on a connection. Only if that was the case we let the
time-wait socket expire after the RTO, otherwise normal TCP_TIMEWAIT_LEN
will be used. But we don't verify this on incoming SYN packets. If a
connection teardown was less than TCP_PAWS_MSL seconds in the past we
cannot guarantee to not accept data packets from an old connection if
no timestamps are present. We should drop this SYN packet. This patch
closes this loophole.
Please note, this patch does not make tcp_tw_recycle in any way more
usable but only adds another safety check:
Sporadic drops of SYN packets because of reordering in the network or
in the socket backlog queues can happen. Users behing NAT trying to
connect to a tcp_tw_recycle enabled server can get caught in blackholes
and their connection requests may regullary get dropped because hosts
behind an address translator don't have synchronized tcp timestamp clocks.
tcp_tw_recycle cannot work if peers don't have tcp timestamps enabled.
In general, use of tcp_tw_recycle is disadvised.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we use the correct address-family-specific function for
handling MTU reductions from within tcp_release_cb().
Previously AF_INET6 sockets were incorrectly always using the IPv6
code path when sometimes they were handling IPv4 traffic and thus had
an IPv4 dst.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Diagnosed-by: Willem de Bruijn <willemb@google.com>
Fixes: 563d34d057 ("tcp: dont drop MTU reduction indications")
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of 4fddbf5d78 ("sit: strictly restrict incoming traffic to tunnel link device"),
when looking up a tunnel, tunnel's underlying interface (t->parms.link)
is verified to match incoming traffic's ingress device.
However the comparison was incorrectly based on skb->dev->iflink.
Instead, dev->ifindex should be used, which correctly represents the
interface from which the IP stack hands the ipip6 packets.
This allows setting up sit tunnels bound to vlan interfaces (otherwise
incoming ipip6 traffic on the vlan interface was dropped due to
ipip6_tunnel_lookup match failure).
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I-Frame which is going to be resend already has FCS field added and set
(if it was required). Adding additional FCS field calculated from data +
old FCS in resend function is incorrect. This patch fix that.
Issue has been found during PTS testing.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is no need to decrease pdu size with L2CAP SDU lenght in Start
L2CAP SDU frame. Start packtet is just 2 bytes longer as specified and
we can keep payload as long as possible.
When testing SAR L2CAP against PTS, L2CAP channel is usually configured
in that way, that SDU = MPS * 3. PTS expets then 3 I-Frames from IUT: Start,
Continuation and End frame.
Without this fix, we sent 4 I-Frames. We could pass a test by using -b
option in l2test and send just two bytes less than SDU length. With this
patch no need to use -b option.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduce the common error path on failure of Tx by
inserting the label 'err_tx'.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Nicolas Dichtel