The emulate_ua_intlck_ctrl device attribute accepts values of 0, 1 or 2 via
ConfigFS, which map to unit attention interlocks control codes in the MODE
SENSE control Mode Page. Use an enum to track these values so that it's
clear that, unlike the remaining emulate_X attributes,
emulate_ua_intlck_ctrl isn't boolean.
Link: https://marc.info/?l=target-devel&m=158227825428798
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This should harden us against configfs API regressions similar to the one
fixed by the previous commit.
Link: https://marc.info/?l=target-devel&m=158211731505174
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The LIO unmap_zeroes_data device attribute is mapped to the LBPRZ flag in
the READ CAPACITY(16) and Thin Provisioning VPD INQUIRY responses.
The unmap_zeroes_data attribute is exposed via configfs, where any write
value is correctly validated via strtobool(). However, when initialised via
target_configure_unmap_from_queue() it takes the value of the device's
max_write_zeroes_sectors queue limit, which is non-boolean.
A non-boolean value can be read from configfs, but attempting to write the
same value back results in -EINVAL, causing problems for configuration
utilities such as targetcli.
Link: https://marc.info/?l=target-devel&m=158213354011309
Fixes: 2237498f0b ("target/iblock: Convert WRITE_SAME to blkdev_issue_zeroout")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Maintaining tpg_list without ever iterating over it is not useful. Hence
remove tpg_list. This patch does not change the behavior of the SCSI target
code.
Cc: Mike Christie <mchristie@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Link: https://lore.kernel.org/r/20190930232224.58980-1-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of tracking the initiator that established an SPC-2 reservation,
track the session through which the SPC-2 reservation has been
established. This patch does not change any functionality.
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Whether or not a session is being torn down does not affect whether or not
SCSI commands are in the task set. Hence remove the "tearing down" checks
from the TMF code. The TRANSPORT_ISTATE_PROCESSING check is left out
because it is now safe to wait for a command that is in that state. The
CMD_T_PRE_EXECUTE is left out because abort processing is postponed until
after commands have left the pre-execute state since the patch that makes
TMF processing synchronous.
See also commit 1c21a48055 ("target: Avoid early CMD_T_PRE_EXECUTE
failures during ABORT_TASK").
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation for supporting user provided vendor strings, add an extra
byte to the vendor, model and revision arrays in struct t10_wwn. This
ensures that the full INQUIRY data can be carried in the arrays along with
a null-terminator.
Change a number of array readers and writers so that they account for
explicit null-termination:
- The pscsi_set_inquiry_info() and emulate_model_alias_store() codepaths
don't currently explicitly null-terminate; fix this.
- Existing t10_wwn field dumps use for-loops which step over
null-terminators for right-padding.
+ Use printf with width specifiers instead.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The TASK ABORTED STATUS (TAS) bit is defined as follows in SAM:
"TASK_ABORTED: this status shall be returned if a command is aborted by a
command or task management function on another I_T nexus and the control
mode page TAS bit is set to one". TAS handling is spread over the target
core and the iSCSI target driver. If a LUN RESET is received, the target
core will send the TASK_ABORTED response for all commands for which such a
response has to be sent. If an ABORT TASK is received, only the iSCSI
target driver will send the TASK_ABORTED response for the commands for
which that response has to be sent. That is a bug since all target drivers
have to honor the TAS bit. Fix this by moving the code that handles TAS
from the iSCSI target driver into the target core. Additionally, if a
command has been aborted, instead of sending the TASK_ABORTED status from
the context that processes the SCSI command send it from the context of the
ABORT TMF. The core_tmr_abort_task() change in this patch causes the
CMD_T_TAS flag to be set if a TASK_ABORTED status has to be sent back to
the initiator that submitted the command. If that flag has been set
transport_cmd_finish_abort() will send the TASK_ABORTED response.
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but makes the patch that makes
TMF handling synchronous easier to read.
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A quote from SAM-5: "The order in which task management requests are
processed is not specified by the SCSI architecture model. The SCSI
architecture model does not require in-order delivery of such task
management requests or processing by the task manager in the order
received. To guarantee the processing order of task management requests
referencing sent to a specific logical unit, an application client should
not have more than one such task management request pending to that logical
unit." This means that it is safe to use the system workqueues instead of
tmr_wq for processing TMFs. An intended side effect of this patch is that
it enables concurrent processing of TMFs.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A session must only be released after all code that accesses the session
structure has finished. Make sure that this is the case by introducing a
new command counter per session that is only decremented after the
.release_cmd() callback has finished. This patch fixes the following crash:
BUG: KASAN: use-after-free in do_raw_spin_lock+0x1c/0x130
Read of size 4 at addr ffff8801534b16e4 by task rmdir/14805
CPU: 16 PID: 14805 Comm: rmdir Not tainted 4.18.0-rc2-dbg+ #5
Call Trace:
dump_stack+0xa4/0xf5
print_address_description+0x6f/0x270
kasan_report+0x241/0x360
__asan_load4+0x78/0x80
do_raw_spin_lock+0x1c/0x130
_raw_spin_lock_irqsave+0x52/0x60
srpt_set_ch_state+0x27/0x70 [ib_srpt]
srpt_disconnect_ch+0x1b/0xc0 [ib_srpt]
srpt_close_session+0xa8/0x260 [ib_srpt]
target_shutdown_sessions+0x170/0x180 [target_core_mod]
core_tpg_del_initiator_node_acl+0xf3/0x200 [target_core_mod]
target_fabric_nacl_base_release+0x25/0x30 [target_core_mod]
config_item_release+0x9c/0x110 [configfs]
config_item_put+0x26/0x30 [configfs]
configfs_rmdir+0x3b8/0x510 [configfs]
vfs_rmdir+0xb3/0x1e0
do_rmdir+0x262/0x2c0
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since transport_clear_lun_ref() already waits until the percpu-refcount
.release() method is called, it is not necessary to wait first until
percpu_ref_kill_and_confirm() has finished transitioning the refcount into
atomic mode. Remove the code that waits for percpu_ref_kill_and_confirm()
to complete and also the completion object that is used by that code. This
patch does not change the behavior of the SCSI target code.
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Disseldorp <ddiss@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On write, the pi_prot_format configfs attribute invokes the device
format_prot() callback if present. Read dumps the contents of
se_dev_attrib.pi_prot_format which is always zero. Make the configfs
attribute write-only, and drop the always zero se_dev_attrib.pi_prot_format
storage.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The new emulate_pr backstore attribute allows for Persistent Reservation
and SCSI2 RESERVE/RELEASE support to be completely disabled. This can be
useful for scenarios such as:
- Ensuring ATS (Compare & Write) usage on recent VMware ESXi initiators.
- Allowing clustered (e.g. tcm-user) backends to block such requests,
avoiding the multi-node reservation state propagation.
When explicitly disabled, PR and RESERVE/RELEASE requests receive Invalid
Command Operation Code response sense data.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 057085e522 ("target: Fix race for SCF_COMPARE_AND_WRITE_POST
checking") removed the code that checks the SCF_COMPARE_AND_WRITE_POST
flag. Hence also remove the flag itself.
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
se_dev_entry.ua_count is only used to check whether or not
se_dev_entry.ua_list is empty. Use list_empty_careful() instead. Checking
whether or not ua_list is empty without holding the lock that protects that
list is fine because the code that dequeues from that list will check again
whether or not that list is empty.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of embedding the completion that is used for waiting for command
completion in struct se_cmd, let the context that waits for command
completion allocate it. This makes it possible to have a single code path
for non-aborted and aborted commands in target_release_cmd_kref() and
avoids that transport_generic_free_cmd() has to call
cmd->se_tfo->release_cmd() directly. This patch does not change any
functionality. Note: transport_generic_free_cmd() only waits until the
se_cmd reference count has reached zero after it has set both
CMD_T_FABRIC_STOP and CMD_T_ABORTED.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Target drivers must call target_sess_cmd_list_set_waiting() and
target_wait_for_sess_cmds() before freeing a session. Since freeing a
session is only safe after all commands that are associated with a session
have finished, make target_wait_for_sess_cmds() also wait for commands that
are being aborted. Instead of setting a flag in each pending command from
target_sess_cmd_list_set_waiting() and waiting in
target_wait_for_sess_cmds() on a per-command completion, only set a
per-session flag in the former function and wait on a per-session
completion in the latter function. This change is safe because once a SCSI
initiator system has submitted a command a target system is always allowed
to execute it to completion. See also commit 0f4a943168 ("target: Fix
remote-port TMR ABORT + se_cmd fabric stop").
This patch is based on the following two patches:
* Bart Van Assche, target: Simplify session shutdown code, February 19, 2015
(8df5463d7d).
* Christoph Hellwig, target: Rework session shutdown code, December 7, 2015
(http://thread.gmane.org/gmane.linux.scsi.target.devel/10695).
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sbitmap and the percpu_ida perform essentially the same task,
allocating tags for commands. The sbitmap outperforms the percpu_ida as
documented here: https://lkml.org/lkml/2014/4/22/553
The sbitmap interface is a little harder to use, but being able to remove
the percpu_ida code and getting better performance justifies the additional
complexity.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> # f_tcm
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce target_free_tag() and convert all drivers to use it.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a tape drive is exported via LIO using the pscsi module, a read
that requests more bytes per block than the tape can supply returns an
empty buffer. This is because the pscsi pass-through target module sees
the "ILI" illegal length bit set and thinks there is no reason to return
the data.
This is a long-standing transport issue, since it assumes that no data
need be returned under a check condition, which isn't always the case
for tape.
Add in a check for tape reads with the ILI, EOM, or FM bits set, with a
sense code of NO_SENSE, treating such cases as if the read
succeeded. The layered tape driver then "does the right thing" when it
gets such a response.
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds a new group of files that are to be used to
have the kernel module execution some action. The next patch
will have target_core_user use the group/files to be able to block
a device and to reset its memory buffer used to pass commands
between user/kernel space.
This type of file is different from the existing device attributes
in that they may be write only and when written to they result in
the kernel module executing some function. These need to be
separate from the normal device attributes which get/set device
values so userspace can continue to loop over all the attribs and
get/set them during initialization.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Add SAM_STAT_BUSY sense_reason. The next patch will have
target_core_user return this value while it is temporarily
blocked and restarting.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"This series is predominantly bug-fixes, with a few small improvements
that have been outstanding over the last release cycle.
As usual, the associated bug-fixes have CC' tags for stable.
Also, things have been particularly quiet wrt new developments the
last months, with most folks continuing to focus on stability atop 4.x
stable kernels for their respective production configurations.
Also at this point, the stable trees have been synced up with
mainline. This will continue to be a priority, as production users
tend to run exclusively atop stable kernels, a few releases behind
mainline.
The highlights include:
- Fix PR PREEMPT_AND_ABORT null pointer dereference regression in
v4.11+ (tangwenji)
- Fix OOPs during removing TCMU device (Xiubo Li + Zhang Zhuoyu)
- Add netlink command reply supported option for each device (Kenjiro
Nakayama)
- cxgbit: Abort the TCP connection in case of data out timeout (Varun
Prakash)
- Fix PR/ALUA file path truncation (David Disseldorp)
- Fix double se_cmd completion during ->cmd_time_out (Mike Christie)
- Fix QUEUE_FULL + SCSI task attribute handling in 4.1+ (Bryant Ly +
nab)
- Fix quiese during transport_write_pending_qf endless loop (nab)
- Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK in 3.14+
(Don White + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (35 commits)
tcmu: Add a missing unlock on an error path
tcmu: Fix some memory corruption
iscsi-target: Fix non-immediate TMR reference leak
iscsi-target: Make TASK_REASSIGN use proper se_cmd->cmd_kref
target: Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK
target: Fix quiese during transport_write_pending_qf endless loop
target: Fix caw_sem leak in transport_generic_request_failure
target: Fix QUEUE_FULL + SCSI task attribute handling
iSCSI-target: Use common error handling code in iscsi_decode_text_input()
target/iscsi: Detect conn_cmd_list corruption early
target/iscsi: Fix a race condition in iscsit_add_reject_from_cmd()
target/iscsi: Modify iscsit_do_crypto_hash_buf() prototype
target/iscsi: Fix endianness in an error message
target/iscsi: Use min() in iscsit_dump_data_payload() instead of open-coding it
target/iscsi: Define OFFLOAD_BUF_SIZE once
target: Inline transport_put_cmd()
target: Suppress gcc 7 fallthrough warnings
target: Move a declaration of a global variable into a header file
tcmu: fix double se_cmd completion
target: return SAM_STAT_TASK_SET_FULL for TCM_OUT_OF_RESOURCES
...
This patch fixes bug where early se_cmd exceptions that occur
before backend execution can result in use-after-free if/when
a subsequent ABORT_TASK occurs for the same tag.
Since an early se_cmd exception will have had se_cmd added to
se_session->sess_cmd_list via target_get_sess_cmd(), it will
not have CMD_T_COMPLETE set by the usual target_complete_cmd()
backend completion path.
This causes a subsequent ABORT_TASK + __target_check_io_state()
to signal ABORT_TASK should proceed. As core_tmr_abort_task()
executes, it will bring the outstanding se_cmd->cmd_kref count
down to zero releasing se_cmd, after se_cmd has already been
queued with error status into fabric driver response path code.
To address this bug, introduce a CMD_T_PRE_EXECUTE bit that is
set at target_get_sess_cmd() time, and cleared immediately before
backend driver dispatch in target_execute_cmd() once CMD_T_ACTIVE
is set.
Then, check CMD_T_PRE_EXECUTE within __target_check_io_state() to
determine when an early exception has occured, and avoid aborting
this se_cmd since it will have already been queued into fabric
driver response path code.
Reported-by: Donald White <dew@datera.io>
Cc: Donald White <dew@datera.io>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If a PERSISTENT RESERVE OUT command with a REGISTER service action or a
REGISTER AND IGNORE EXISTING KEY service action or REGISTER AND MOVE
service action is attempted, but there are insufficient device server
resources to complete the operation, then the command shall be terminated
with CHECK CONDITION status, with the sense key set to ILLEGAL REQUEST,and
the additonal sense code set to INSUFFICIENT REGISTRATION RESOURCES.
Signed-off-by: tangwenji <tang.wenji@zte.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
g_device_list is no longer needed because we now use the idr code
for lookups and seaches.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In the next patches we will add tcmu netlink support that allows
userspace to send commands to target_core_user. To execute operations
on a se_device/tcmu_dev we need to be able to look up a dev by any old
id. This patch replaces the se_device->dev_index with a idr created
id.
The next patches will also remove the g_device_list and replace it with
the idr.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The last user of se_device.dev_list was removed through commit
0fd97ccf45 ("target: kill struct se_subsystem_dev"). Hence
also remove se_device.dev_list.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch introduces support in target_submit_tmr() for locating a
unpacked_lun from an existing se_cmd->tag during ABORT_TASK.
When TARGET_SCF_LOOKUP_LUN_FROM_TAG is set, target_submit_tmr()
will do the extra lookup via target_lookup_lun_from_tag() and
subsequently invoke transport_lookup_tmr_lun() so a proper
percpu se_lun->lun_ref is taken before workqueue dispatch into
se_device->tmr_wq happens.
Aside from the extra target_lookup_lun_from_tag(), the existing
code-path remains unchanged.
Reviewed-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Quinn Tran <quinn.tran@cavium.com>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of using a hardcoded magic value in se_lun when verifying
a target config_item symlink source during target_fabric_mappedlun_link(),
go ahead and use target_fabric_port_item_ops directly instead.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of using a hardcoded magic value in se_device when verifying
a target config_item symlink source during target_fabric_port_link(),
go ahead and use target_core_dev_item_ops directly instead.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Currently ramdisk and fileio always perform PI verification
before and after backend IO. This approach is not very flexible.
Because some one may want to postpone this work to other layers in
IO stack. For example if we want to test blk_integrity_profile
testcase:
dee408c868
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Multiple threads could be writing to alua_access_state at
the same time, or there could be multiple STPGs in flight
(different initiators sending them or one initiator sending
them to different ports), or a combo of both and the
core_alua_do_transition_tg_pt calls will race with each other.
Because from the last patches we no longer delay running
core_alua_do_transition_tg_pt_work, there does not seem to be
any point in running that in a workqueue. And, we always
wait for it to complete one way or another, so we can sleep
in this code path. So, this patch made over target-pending just adds a
mutex and does the work core_alua_do_transition_tg_pt_work was doing in
core_alua_do_transition_tg_pt.
There is also no need to use an atomic for the
tg_pt_gp_alua_access_state. In core_alua_do_transition_tg_pt we will
test and set it under the transition mutex. And, it is a int/32 bits
so in the other places where it is read, we will never see it partially
updated.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a set of queue-full response handling
bugs, where outgoing responses are leaked when a fabric
driver is propagating non -EAGAIN or -ENOMEM errors
to target-core.
It introduces TRANSPORT_COMPLETE_QF_ERR state used to
signal when CHECK_CONDITION status should be generated,
when fabric driver ->write_pending(), ->queue_data_in(),
or ->queue_status() callbacks fail with non -EAGAIN or
-ENOMEM errors, and data-transfer should not be retried.
Note all fabric driver -EAGAIN and -ENOMEM errors are
still retried indefinately with associated data-transfer
callbacks, following existing queue-full logic.
Also fix two missing ->queue_status() queue-full cases
related to CMD_T_ABORTED w/ TAS status handling.
Reported-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Potnuri Bharat Teja <bharat@chelsio.com>
Tested-by: Potnuri Bharat Teja <bharat@chelsio.com>
Cc: Potnuri Bharat Teja <bharat@chelsio.com>
Reported-by: Steve Wise <swise@opengridcomputing.com>
Cc: Steve Wise <swise@opengridcomputing.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch closes a race between se_lun deletion during configfs
unlink in target_fabric_port_unlink() -> core_dev_del_lun()
-> core_tpg_remove_lun(), when transport_clear_lun_ref() blocks
waiting for percpu_ref RCU grace period to finish, but a new
NodeACL mappedlun is added before the RCU grace period has
completed.
This can happen in target_fabric_mappedlun_link() because it
only checks for se_lun->lun_se_dev, which is not cleared until
after transport_clear_lun_ref() percpu_ref RCU grace period
finishes.
This bug originally manifested as NULL pointer dereference
OOPsen in target_stat_scsi_att_intr_port_show_attr_dev() on
v4.1.y code, because it dereferences lun->lun_se_dev without
a explicit NULL pointer check.
In post v4.1 code with target-core RCU conversion, the code
in target_stat_scsi_att_intr_port_show_attr_dev() no longer
uses se_lun->lun_se_dev, but the same race still exists.
To address the bug, go ahead and set se_lun>lun_shutdown as
early as possible in core_tpg_remove_lun(), and ensure new
NodeACL mappedlun creation in target_fabric_mappedlun_link()
fails during se_lun shutdown.
Reported-by: James Shen <jcs@datera.io>
Cc: James Shen <jcs@datera.io>
Tested-by: James Shen <jcs@datera.io>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The implicit transition time tells initiators the min time
to wait before timing out a transition. We currently schedule
the transition to occur in tg_pt_gp_implicit_trans_secs
seconds so there is no room for delays. If
core_alua_do_transition_tg_pt_work->core_alua_update_tpg_primary_metadata
needs to write out info to a remote file, then the initiator can
easily time out the operation.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
It's not used by anything in <linux/sched.h> anymore.
This reduces the preprocessed size of <linux/sched.h> and
speeds up the build a bit.
Also fix code that implicitly relied on headers included by <linux/cgroup-defs.h>.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- enable dual mode (initiator + target) qla2xxx operation. (Quinn +
Himanshu)
- add a framework for qla2xxx async fabric discovery. (Quinn +
Himanshu)
- enable iscsi PDU DDP completion offload in cxgbit/T6 NICs. (Varun)
- fix target-core handling of aborted failed commands. (Bart)
- fix a long standing target-core issue NULL pointer dereference with
active I/O LUN shutdown. (Rob Millner + Bryant + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (44 commits)
target: Add counters for ABORT_TASK success + failure
iscsi-target: Fix early login failure statistics misses
target: Fix NULL dereference during LUN lookup + active I/O shutdown
target: Delete tmr from list before processing
target: Fix handling of aborted failed commands
uapi: fix linux/target_core_user.h userspace compilation errors
target: export protocol identifier
qla2xxx: Fix a warning reported by the "smatch" static checker
target/iscsi: Fix unsolicited data seq_end_offset calculation
target/cxgbit: add T6 iSCSI DDP completion feature
target/cxgbit: Enable DDP for T6 only if data sequence and pdu are in order
target/cxgbit: Use T6 specific macros to get ETH/IP hdr len
target/cxgbit: use cxgb4_tp_smt_idx() to get smt idx
target/iscsi: split iscsit_check_dataout_hdr()
target: Remove command flag CMD_T_DEV_ACTIVE
target: Remove command flag CMD_T_BUSY
target: Move session check from target_put_sess_cmd() into target_release_cmd_kref()
target: Inline transport_cmd_check_stop()
target: Remove an overly chatty debug message
target: Stop execution if CMD_T_STOP has been set
...
In the following patches we are going to remove various headers
from sched.h and other headers that sched.h includes.
To make those patches build cleanly prepare the scene by adding
dependencies to various files that learned to rely on those
to-be-removed dependencies.
These changes all make sense standalone: they add a header for
a data type that a particular .c or .h file is using.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch introduces two counters for ABORT_TASK success +
failure under:
/sys/kernel/config/target/core/$HBA/$DEV/statistics/scsi_tgt_dev/
that are useful for diagnosing various backend device latency
and front fabric issues.
Normally when folks see alot of aborts_complete happening,
it means the backend device I/O completion latency is high,
and not returning completions fast enough before host side
timeouts trigger.
And normally when folks see alot of aborts_no_task, it means
completions are being posted by target-core into fabric driver
code, but the responses aren't making it back to the host.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When transport_clear_lun_ref() is shutting down a se_lun via
configfs with new I/O in-flight, it's possible to trigger a
NULL pointer dereference in transport_lookup_cmd_lun() due
to the fact percpu_ref_get() doesn't do any __PERCPU_REF_DEAD
checking before incrementing lun->lun_ref.count after
lun->lun_ref has switched to atomic_t mode.
This results in a NULL pointer dereference as LUN shutdown
code in core_tpg_remove_lun() continues running after the
existing ->release() -> core_tpg_lun_ref_release() callback
completes, and clears the RCU protected se_lun->lun_se_dev
pointer.
During the OOPs, the state of lun->lun_ref in the process
which triggered the NULL pointer dereference looks like
the following on v4.1.y stable code:
struct se_lun {
lun_link_magic = 4294932337,
lun_status = TRANSPORT_LUN_STATUS_FREE,
.....
lun_se_dev = 0x0,
lun_sep = 0x0,
.....
lun_ref = {
count = {
counter = 1
},
percpu_count_ptr = 3,
release = 0xffffffffa02fa1e0 <core_tpg_lun_ref_release>,
confirm_switch = 0x0,
force_atomic = false,
rcu = {
next = 0xffff88154fa1a5d0,
func = 0xffffffff8137c4c0 <percpu_ref_switch_to_atomic_rcu>
}
}
}
To address this bug, use percpu_ref_tryget_live() to ensure
once __PERCPU_REF_DEAD is visable on all CPUs and ->lun_ref
has switched to atomic_t, all new I/Os will fail to obtain
a new lun->lun_ref reference.
Also use an explicit percpu_ref_kill_and_confirm() callback
to block on ->lun_ref_comp to allow the first stage and
associated RCU grace period to complete, and then block on
->lun_ref_shutdown waiting for the final percpu_ref_put()
to drop the last reference via transport_lun_remove_cmd()
before continuing with core_tpg_remove_lun() shutdown.
Reported-by: Rob Millner <rlm@daterainc.com>
Tested-by: Rob Millner <rlm@daterainc.com>
Cc: Rob Millner <rlm@daterainc.com>
Tested-by: Vaibhav Tandon <vst@datera.io>
Cc: Vaibhav Tandon <vst@datera.io>
Tested-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- Add new Broadcom bnxt_re RoCE driver
- rxe driver updates
- ioctl cleanups
- ETH_P_IBOE declaration cleanup
- IPoIB changes
- Add port state cache
- Allow srpt driver to accept guids as port names in config
- Update to hfi1 driver
- Update to srp driver
- Lots of misc. minor changes all over
-----BEGIN PGP SIGNATURE-----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=ugNm
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"First set of updates for 4.11 kernel merge window
- Add new Broadcom bnxt_re RoCE driver
- rxe driver updates
- ioctl cleanups
- ETH_P_IBOE declaration cleanup
- IPoIB changes
- Add port state cache
- Allow srpt driver to accept guids as port names in config
- Update to hfi1 driver
- Update to srp driver
- Lots of misc minor changes all over"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (114 commits)
RDMA/bnxt_re: fix for "bnxt_en: Update to firmware interface spec 1.7.0."
rdma_cm: fail iwarp accepts w/o connection params
IB/srp: Drain the send queue before destroying a QP
IB/core: Add support for draining IB_POLL_DIRECT completion queues
IB/srp: Improve an error path
IB/srp: Make a diagnostic message more informative
IB/srp: Document locking conventions
IB/srp: Fix race conditions related to task management
IB/srp: Avoid that duplicate responses trigger a kernel bug
IB/SRP: Avoid using IB_MR_TYPE_SG_GAPS
RDMA/qedr: Fix some error handling
RDMA/bnxt_re: add DCB dependency
IB/hns: include linux/module.h
IB/vmw_pvrdma: Expose vendor error to ULPs
vmw_pvrdma: switch to pci_alloc_irq_vectors
IB/hfi1: use size_t for passing array length
IB/ipoib: Remove redudant label
IB/ipoib: remove the unnecessary memory free
IB/mthca: switch to pci_alloc_irq_vectors
IB/hfi1: Code reuse with memdup_copy
...
The code that tests the CMD_T_DEV_ACTIVE flag has been removed. Hence
also remove the flag itself.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The patch that reworks task management function handling guarantees
that target_remove_from_state_list() is always called with CMD_T_BUSY
cleared. Since that function is the only function that tests that flag
this means that that flag is now superfluous. Hence remove that flag.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Member tmr_lun of se_tmr_req is set but not used. Hence remove it.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a long-standing bug with multi-session
(eg: iscsi-target + iser-target) se_node_acl dynamic free
withini transport_deregister_session().
This bug is caused when a storage endpoint is configured with
demo-mode (generate_node_acls = 1 + cache_dynamic_acls = 1)
initiators, and initiator login creates a new dynamic node acl
and attaches two sessions to it.
After that, demo-mode for the storage instance is disabled via
configfs (generate_node_acls = 0 + cache_dynamic_acls = 0) and
the existing dynamic acl is never converted to an explicit ACL.
The end result is dynamic acl resources are released twice when
the sessions are shutdown in transport_deregister_session().
If the storage instance is not changed to disable demo-mode,
or the dynamic acl is converted to an explict ACL, or there
is only a single session associated with the dynamic ACL,
the bug is not triggered.
To address this big, move the release of dynamic se_node_acl
memory into target_complete_nacl() so it's only freed once
when se_node_acl->acl_kref reaches zero.
(Drop unnecessary list_del_init usage - HCH)
Reported-by: Rob Millner <rlm@daterainc.com>
Tested-by: Rob Millner <rlm@daterainc.com>
Cc: Rob Millner <rlm@daterainc.com>
Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
David Disseldorp