Based on the hardware spec, the BDW GT3 has the different configuration
with the BDW GT1/GT2. So split the BDW device info definition.
This is to do the preparation for adding the Dual BSD rings on BDW GT3 machine.
V1->V2: Follow Daniel's comment to pay attention to the stolen check for BDW
in kernel/early-quirks.c
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to make sure that userspace keeps on following the contract,
otherwise we won't be able to use the reserved fields at all.
v2: Add DRM_DEBUG (Chris)
Testcase: igt/gem_exec_params/*-dirt
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bit tricky since 0 is also a valid constant ...
v2: Add DRM_DEBUG (Chris)
Testcase: igt/gem_exec_params/rel-constants-*
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we catch it, but silently succeed. Our userspace is
better than this.
v2: Add DRM_DEBUG (Chris)
Testcase: igt/gem_exec_params/sol-reset-*
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we include the expected values for the failing ring register checks,
it makes it marginally easier to see which is the culprit.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During module load, if we fail to initialise the rings, we abort the
load reporting EIO. However during resume, even though we report EIO as
we fail to reinitialize the ringbuffers, the resume continues and the
device is restored - albeit in a non-functional state. As we cannot
execute any commands on the GPU, it is effectively wedged, mark it so.
As we now preserve the ringbuffers across resume, this should prevent
UXA from falling into the trap of repeatedly sending invalid
batchbuffers and dropping all further rendering into /dev/null.
Reported-and-tested-by: Jiri Kosina <jkosina@suse.cz>
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
[danvet: Drop unused error, spotted by Oscar.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Even without enabling the ringbuffers to allow command execution, we can
still control the display engines to enable modesetting. So make the
ringbuffer initialization failure soft, and mark the GPU as wedged
instead.
v2: Only treat an EIO from ring initialisation as a soft failure, and
abort module load for any other failure, such as allocation failures.
v3: Add an *ERROR* prior to declaring the GPU wedged so that it stands
out like a sore thumb in the logs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tearing down the ring buffers across resume is overkill, risks
unnecessary failure and increases fragmentation.
After failure, since the device is still active we may end up trying to
write into the dangling iomapping and trigger an oops.
v2: stop_ringbuffers() was meant to call stop(ring) not
cleanup(ring) during resume!
Reported-by: Jae-hyeon Park <jhyeon@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=72351
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
[danvet: s/ring->obj == NULL/!intel_ring_initialized(ring)/ as
suggested by Oscar.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For readibility and guess at the meaning behind the constants.
v2: Claim only the meagerest connections with reality.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I don't think this is necessary; at least it doesn't appear to be on my
BYT. Dropping it speeds up our shutdown code a little, in some cases
resulting in faster init times.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Next pull request, this time more of the drm de-midlayering work. The big
thing is that his patch series here removes everything from drm_bus except
the set_busid callback. Thierry has a few more patches on top of this to
make that one optional to.
With that we can ditch all the non-pci drm_bus implementations, which
Thierry has already done for the fake tegra host1x drm_bus.
Reviewed by Thierry, Laurent and David and now also survived some testing
on my intel boxes to make sure the irq fumble is fixed correctly ;-) The
last minute rebase was just to add the r-b tags from Thierry for the 2
patches I've redone.
* 'drm-init-cleanup' of git://people.freedesktop.org/~danvet/drm:
drm/<drivers>: don't set driver->dev_priv_size to 0
drm: Remove dev->kdriver
drm: remove drm_bus->get_name
drm: rip out dev->devname
drm: inline drm_pci_set_unique
drm: remove bus->get_irq implementations
drm: pass the irq explicitly to drm_irq_install
drm/irq: Look up the pci irq directly in the drm_control ioctl
drm/irq: track the irq installed in drm_irq_install in dev->irq
drm: rename dev->count_lock to dev->buf_lock
drm: Rip out totally bogus vga_switcheroo->can_switch locking
drm: kill drm_bus->bus_type
drm: remove drm_dev_to_irq from drivers
drm/irq: remove cargo-culted locking from irq_install/uninstall
drm/irq: drm_control is a legacy ioctl, so pci devices only
drm/pci: fold in irq_by_busid support
drm/irq: simplify irq checks in drm_wait_vblank
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
In commit a51435a313
Author: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Date: Wed Mar 12 16:39:40 2014 +0530
drm/i915: disable rings before HW status page setup
we reordered stopping the rings to do so before we set the HWS register.
However, there is an extra workaround for g45 to reset the rings twice,
and for consistency we should apply that workaround before setting the
HWS to be sure that the rings are truly stopped.
Reference: http://lkml.kernel.org/r/20140423202248.GA3621@amd.pavel.ucw.cz
Tested-by: Pavel Machek <pavel@ucw.cz>
Cc: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The status bits are unconditionally set, the control bits only enable
the actual interrupt generation. Which means if we get some random
other interrupts we'll bogusly complain about them.
So restrict the WARN to platforms with a sane hotplug interrupt
handling scheme. And even more important also don't attempt to process
the hpd bit since we've detected a storm already. Instead just clear
the bit silently.
This WARN has been introduced in
commit b8f102e8bf
Author: Egbert Eich <eich@suse.de>
Date: Fri Jul 26 14:14:24 2013 +0200
drm/i915: Add messages useful for HPD storm detection debugging (v2)
before that we silently handled the hpd event and so partially
defeated the storm detection.
v2: Pimp commit message (Jani)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Egbert Eich <eich@suse.de>
Cc: bitlord <bitlord0xff@gmail.com>
Reported-by: bitlord <bitlord0xff@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When PPGTT was disabled by default, the patch also prevented the user
from overriding this behavior via module parameter. Being able to test
this on arbitrary kernels is extremely beneficial to track down the
remaining bugs. The patch that prevented this was:
commit 93a25a9e2d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 6 09:40:43 2014 +0100
drm/i915: Disable full ppgtt by default
By default PPGTT is set to -1. 0 means off, 1 means aliasing only, 2
means full, all other values are reserved.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If the inherited BIOS framebuffer is smaller than the mode selected for
fbdev, then if we continue to use it then we cause display corruption as
we do not setup the panel fitter to upscale.
Regression from commit d978ef1445
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Mar 7 08:57:51 2014 -0800
drm/i915: Wrap the preallocated BIOS framebuffer and preserve for KMS fbcon v12
v2: Add a debug message to track the discard of the BIOS fb.
v3: Ville pointed out the difference between ref/unref
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77767
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Unfortunately this requires a drm-wide change, and I didn't see a sane
way around that. Luckily it's fairly simple, we just need to inline
the respective get_irq implementation from either drm_pci.c or
drm_platform.c.
With that we can now also remove drm_dev_to_irq from drm_irq.c.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So I just wanted to add a new field to struct drm_device and
accidentally stumbled over something. According to comments
dev->open_count is protected by dev->count_lock, but that's totally
not the case. It's protected by drm_global_mutex.
Unfortunately the vga switcheroo callbacks took this comment at face
value. The problem is that we can't just take the drm_global_mutex
because:
- It would lead to a locking inversion with the driver load/unload
paths.
- It wouldn't actually protect anything, for that we'd need to wrap
the entire vga switcheroo code in the drm_global_mutex. And I'm not
sure whether that would actually solve anything.
What we probably want is a try_to_grab_switcheroo reference kind of
thing which is used in the driver's ->open callback. Then we could
move all that ->can_switch madness into the vga switcheroo core where
it really belongs.
But since that would amount to real work take the easy way out and
just add a comment. It's definitely not going to make anything worse
since doing switcheroo state changes while restarting X just isn't
recommended. Even though the delayed switching code does exactly that.
v2:
- Simplify the ->can_switch implementations more (Thierry)
- Fix comment about the dev->open_count locking (Thierry)
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> (v1)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If I unplug the eDP monitor, the BIOS of my machine will enable the
VDD bit, then when the driver loads it will think VDD is enabled. It
will detect that the eDP is not enabled and return false from
intel_edp_init_connector. This will trigger a call to
edp_panel_vdd_off_sync(), which trigger a WARN saying that the
refcount of the power domain is less than zero.
The problem happens because the driver gets a refcount whenever it
enables the VDD bit, and puts the refcount whenever it disables the
VDD bit. But on this case, the BIOS enabled VDD, so all we do is to
call put() without calling get() first, so the code added is there to
make sure we always have the get() in case the BIOS enabled the bit.
This regression was introduced in
commit e9cb81a228
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Thu Nov 21 13:47:23 2013 -0200
drm/i915: get a runtime PM reference when the panel VDD is on
v2: - Rebase
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org (v3.13+)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
... our current modeset code isn't good enough yet to handle this. The
scenario is:
1. BIOS sets up a cloned config with lvds+external screen on the same
pipe, e.g. pipe B.
2. We read out that state for pipe B and assign the gmch_pfit state to
it.
3. The initial modeset switches the lvds to pipe A but due to lack of
atomic modeset we don't recompute the config of pipe B.
-> both pipes now claim (in the sw pipe config structure) to use the
gmch_pfit, which just won't work.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74081
Tested-by: max <manikulin@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In commit
commit 6375b768a9
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Mar 3 11:33:36 2014 +0200
drm/i915: Reject >165MHz modes w/ DVI monitors
the driver started to filter out display modes which exceed the
single-link DVI 165Mz dotclock limits when the monitor doesn't report
itself as being HDMI compliant. The intent was to filter out all
EDID derived modes that require dual-link DVI to operate since we
don't support dual-link.
However the patch went a bit too far and also causes the driver to reject
such modes even when specified by the user. Normally we don't check the
sink limitations when setting a mode from the user. This allows the user
to specify any mode whether the sink reports to support it or not. This
can be useful since often the sinks support more modes than they report
in the EDID.
So relax the checks a bit, and apply the single-link DVI dotclock limit
only when filtering the mode list, and ignore the limit when setting
a user specified mode.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=72961
Tested-by: Nicholas Vinson <nvinson@comcast.net>
Cc: stable@vger.kernel.org [3.14]
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The dev->struct_mutex locking in drm_irq.c only protects
dev->irq_enabled. Which isn't really much at all and only prevents
especially nasty ums userspace from concurrently installing the
interrupt handling a few times. Or at least trying.
There are tons of unlocked readers of dev->irqs_enabled in the vblank
wait code (and by extension also in the pageflip code since that uses
the same vblank timestamp engine).
Real modesetting drivers should ensure that nothing can go haywire
with a sane setup teardown sequence. So we only really need this for
the drm_control ioctl, everywhere else this will just paper over
nastiness.
Note that drm/i915 is a bit specially due to the gem+ums combination.
So there we also need to properly protect the entervt and leavevt
ioctls. But it's definitely saner to do everything in one go than to
drop the lock in-between.
Finally there's the gpu reset code in drm/i915. That one's just race
(concurrent userspace calls to for vblank waits of pageflips could
spuriously fail). So wrap it up in with a nice comment since fixing
this is more involved.
v2: Rebase and fix commit message (Thierry)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some i2c fixes over DisplayPort.
* 'drm-next-3.15-wip' of git://people.freedesktop.org/~deathsimple/linux:
drm/radeon: Improve vramlimit module param documentation
drm/radeon: fix audio pin counts for DCE6+ (v2)
drm/radeon/dp: switch to the common i2c over aux code
drm/dp/i2c: Update comments about common i2c over dp assumptions (v3)
drm/dp/i2c: send bare addresses to properly reset i2c connections (v4)
drm/radeon/dp: handle zero sized i2c over aux transactions (v2)
drm/i915: support address only i2c-over-aux transactions
drm/tegra: dp: Support address-only I2C-over-AUX transactions
The pipe is off at that point in time, so a vblank wait is simply a
50ms wait. Caught by Jesse's verbose "make vblank wait timeouts WARN"
patch. We've probably had a few versions of this float around already.
To document assumptions put a pipe assert into the same place. And
also add a posting read.
If we ever decide to update the eld and infoframes while the pipe is
already on (e.g. for fastboot) then there's lots of work to do. So
better properly document all the hidden assumptions.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some fixes from Intel.
* tag 'drm-intel-fixes-2014-04-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Always use kref tracking for all contexts.
drm/i915: do not setup backlight if not available according to VBT
drm/i915: check VBT for supported backlight type
drm/i915: Disable self-refresh for untiled fbs on i915gm
drm/mm: Don't WARN if drm_mm_reserve_node
We already do this for HSW, but doing it makes sense for everything else
as well. Extend it for ILK/SNB/IVB since that's where the new watermark
code is used.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
[danvet: Resolve conflict since I've plucked this out of the middle of
Ville's series.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like on hsw/bdw the pipe isn't actually running yet at this point.
This holds for both pch ports and the cpu edp port according to my
testing on ilk, snb and ivb.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77297
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This cleans up the checkpatch errors for the merged commit -
commit d3b542fcfc
Author: Shobhit Kumar <shobhit.kumar@intel.com>
Date: Mon Apr 14 11:00:34 2014 +0530
drm/i915: Add parsing support for new MIPI blocks in VBT
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When linking the i2c sysfs file into the connector's directory
pass directory and link target in the right order.
This code was introduced with:
commit 931c1c2698
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Feb 11 17:12:51 2014 +0200
drm/i915: sdvo: add i2c sysfs symlink to the connector's directory
This is the same what we do for DP connectors, so make things more
consistent.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The parser extracts the config block(#52) and sequence(#53) data
and store in private data structures.
v2: Address review comments by Jani
- adjust code for the structure changes for bdb_mipi_config
- add boundry and buffer overflow checks as suggested
- use kmemdup instead of kmalloc and memcpy
v3: More strict check while parsing VBT
- Ensure that at anytime we do not go beyond sequence block
while parsing
- On unknown element fail the whole parsing
v4: Style changes and spell check mostly as suggested by Jani
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we really only need this when the pfit is enabled, at least
I couldn't dicern any difference here. Furthermore the hacks we have
to reconstruct this bit is a bit glaring, and probably only works
because we can't move the lvds port to any other pipe than pipe B on
gen2/3.
So let's just rip this out.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77137 (the LVDS
WARNING log, not the main "VGA can't be turned on" issue).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we always initialize kref for the context, even if we are using fake
contexts for hangstats when there is no hw support, we can forgo the
dance to dereference the ctx->obj and inspect whether we are permitted
to use kref inside i915_gem_context_reference() and _unreference().
My ulterior motive here is to improve the debugging of a use-after-free
of ctx->obj. This patch avoids the dereference here and instead forces
the assertion checks associated with kref.
v2: Refactor the fake contexts to being even more like the real
contexts, so that there is much less duplicated and special case code.
v3: Tweaks.
v4: Tweaks, minor.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76671
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: lu hua <huax.lu@intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[Jani: tiny change to backport to drm-intel-fixes.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Some machines use an external EC for controlling the backlight. Info
about this is present in the VBT. Do not setup native backlight control
if no PWM backlight is available or supported according to VBT. The
acpi_backlight interface appears to work for the EC control.
In most cases there has been no harm done, but it looks like there are
machines out there that have both an EC and our PWM line connected to
the same wire. This, obviously, does not end well.
This should fix the regression caused by
commit bc0bb9fd1c
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Nov 14 12:14:29 2013 +0200
drm/i915: remove QUIRK_NO_PCH_PWM_ENABLE
AFAICT the quirk removed by the above commit effectively resulted in
i915 not driving the backlight PWM output, thus not messing things up.
Additionally this should fix the regression caused by
commit fbc9fe1b4f
Author: Aaron Lu <aaron.lu@intel.com>
Date: Fri Oct 11 21:27:45 2013 +0800
ACPI / video: Do not register backlight if win8 and native interface exists
which left some machines without a functioning backlight interface.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76276
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=47941
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=62281
CC: Aaron Lu <aaron.lu@intel.com>
CC: Eric Griffith <EGriffith92@gmail.com>
CC: Kent Baxley <kent.baxley@canonical.com>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Martin <bugs@mrvanes.com>
Tested-by: jrg.otte@gmail.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The only supported types are none and PWM. Other values are obsolete or
reserved, don't add them.
Tested-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Martin <bugs@mrvanes.com>
Tested-by: jrg.otte@gmail.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a requirement added to the spec. This patch will prevent
persistent corruption on the display.
v2: Make the wait before the vblank wait. (Art)
Try to finish early by polling the register
s/present/prevent (Chris)
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Upgrade debug output to ERROR.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch computes and stored 2nd M/N/TU for switching to different
refresh rate dynamically. PIPECONF_EDP_RR_MODE_SWITCH bit helps toggle
between alternate refresh rates programmed in 2nd M/N/TU registers.
v2: Daniel's review comments
Computing M2/N2 in compute_config and storing it in crtc_config
v3: Modified reference to edp_downclock and edp_downclock_avail based on the
changes made to move them from dev_private to intel_panel.
v4: Modified references to is_drrs_supported based on the changes made to
rename it to drrs_support.
v5: Jani's review comments
Removed superfluous return statements. Changed support for Gen 7 and above.
Corrected indentation. Re-structured the code which finds crtc and connector
from encoder. Changed some logs to be less verbose.
v6: Modifying i915_drrs to include only intel connector as intel_dp can be
derived from intel connector when required.
v7: As per internal review comments, acquiring mutex just before accessing
drrs RR. As per Chris's review comments, added documentation about the use
of locking in the function.
v8: Incorporated Jani's review comments.
Removed reference to edp_downclock.
v9: Jani's review comments. Modified comment in set_drrs. Changed index to
type edp_drrs_refresh_rate_type. Check if PSR is enabled before setting
registers fo DRRS.
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch and finds out the lowest refresh rate supported for the resolution
same as the fixed_mode.
It also checks the VBT fields to see if panel supports seamless DRRS or not.
Based on above data it marks whether eDP panel supports seamless DRRS or not.
This information is needed for supporting seamless DRRS switch for certain
power saving usecases. This patch is tested by enabling the DRM logs and
user should see whether Seamless DRRS is supported or not.
v2: Daniel's review comments
Modified downclock deduction based on intel_find_panel_downclock
v3: Chris's review comments
Moved edp_downclock_avail and edp_downclock to intel_panel
v4: Jani's review comments.
Changed name of the enum edp_panel_type to drrs_support type.
Change is_drrs_supported to drrs_support of type enum drrs_support_type.
v5: Incorporated Jani's review comments
Modify intel_dp_drrs_initialize to return downclock mode. Support for Gen7
and above.
v6: Incorporated Chris's review comments.
Changed initialize to init in intel_drrs_initialize
v7: Incorporated Jani's review comments.
Removed edp_downclock and edp_downclock_avail. Return NULL explicitly.
Make drrs_state and unnamed struct. Move Gen based check inside drrs_init.
v8: Made changes to track PSR enable/disable throughout system use (instead
of just in the init sequence) for disabling/enabling DRRS. Jani's review
comments.
v9: PSR tracking will be done as part of idleness detection patch. Removed
PSR state tracker in i915_drrs. Jani's review comments.
v10: Added log for DRRS not supported in drrs_init
v11: Modification in drrs_init. suggested by Jani
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently it doesn't work. X-tiled self-refresh works flawlessly
otoh. Apparently X still works correctly with linear framebuffers, so
might just be an issue with the initial modeset. It's unclear whether
this just borked wm setup from our side or a hw restriction, but just
disabling gets things going.
Note that this regression was only brought to light with
commit 3f2dc5ac05
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Jan 10 14:06:47 2014 +0200
drm/i915: Fix 915GM self-refresh enable/disable
before that self-refresh for i915GM didn't work at all.
Kudos to Ville for spotting a little bug in the original patch I've
attached to the bug.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76103
Tested-by: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: rebase on top of drm-next with primary plane support.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 4b28a1f3ef.
This patch duct-tapes over some issue in the current bdw rps patches
which must wait with enabling rc6/rps until the very first batch has
been submitted by userspace.
But those patches aren't merged yet, and for upstream we need to have
an in-kernel emission of the very first batch. I shouldn't have
merged this patch so let's revert it again.
Also Imre noticed that even when rps is set up normally there's a
small window (due to the 1s delay of the async rps init work) where we
could runtime suspend already and blow up all over the place. Imre has
a proper fix to block runtime pm until the rps init work has
successfully completed.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We will treat Cherryview like Valleyview for most parts. Add a macro
for cases when we need to tell the two apart.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some MIPI panels might not have resolution which is a multiple of 64 like
1366x768. Enable this feature for such panels by default
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Though HS mode also should work.
v2: Change parameter as "bool hs" as suggested by Jani
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for Generic driver
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise, this can stall pipe. We also need DPLL REFA always
enabled
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As per the hw team's recommendation we need to enable the MIPI port
before enabling the plane and pipe. So call MIPI port enable in
pre_enable phase itself
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Zhao Yakui