devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If a process receives signal while it is waiting for I2C transfer to
complete, an error is returned to the caller and the transfer is aborted.
This can cause the driver to fail subsequent transfers. Also according to
commit d295a86eab (i2c: mv64xxx: work around signals causing I2C
transactions to be aborted) I2C drivers aren't supposed to abort
transactions on signals.
To prevent this switch to use wait_for_completion_timeout() instead of
wait_for_completion_interruptible_timeout() in the designware I2C driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.
So remove devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.
So remove devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Asking for a multi-part message to be handled by this driver is racy; it
has been observed that the following sequence is possible with this
driver:
- send start
- send address + write
- send data
- send (repeated) start
- send address + write
- send (repeated) start
- send address + read
- unrecoverable bus hang (except by system reset)
The problem is that the interrupt handling sees the next event after the
first repeated start is sent - the IFLG bit is set in the register even
though INTEN is disabled.
Let's fix this by moving all of the message processing into interrupt
context, rather than having it partly in IRQ and partly in process
context. This allows us to move immediately to the next message in the
interrupt handler and get on with the transfer, rather than incuring a
couple of scheduling switches to get the next message.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move mv64xxx_i2c_prepare_for_io() higher up in the driver to avoid a
future forward declaration for this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As this driver does not advertise protocol mangling support
(I2C_FUNC_PROTOCOL_MANGLING is not set), having code to act on
I2C_M_NOSTART is illogical, and in any case isn't supportable on
anything but the first message - which makes no sense. Remove
the I2C_M_NOSTART code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Propagate the error code from request_irq() rather than ignoring it
entirely.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As we're changing to using devm_* APIs to fix various problems
in this driver, lets also do devm_kzalloc() while we're here too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver forgets to use clk_put(). Rather than adding clk_put(),
lets instead use devm_clk_get() to obtain this clock so that it's
automatically handled on cleanup.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Eliminate reg_base_p and reg_size, mv64xxx_i2c_unmap_regs() and an
unchecked ioremap() return from this driver by using the devm_*
API for requesting and ioremapping resources.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
mv64xxx_i2c_map_regs() already returns an error code, so lets
propagate that to mv64xxx_i2c_probe()'s caller.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Moorestown support is removed from kernel and Medfield is supported by
i2c-designware-pci. But i2c-intel-mid is still in upstream and community
resources are wasted to maintain it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
This adds device tree support for the ST DDC I2C driver known
as "stu300" in the kernel tree.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull i2c bugfixes from Wolfram Sang:
"These should have been in rc2 but I missed it due to working on devm
longer than expected.
There is one ID addition, since we are touching the driver anyhow.
And the feature bit documentation is one outcome of a debug session
and will make it easier for users to work around problems. The rest
is typical driver bugfixes."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: suppress lockdep warning on delete_device
i2c: mv64xxx: work around signals causing I2C transactions to be aborted
i2c: i801: Document feature bits in modinfo
i2c: designware: add Intel BayTrail ACPI ID
i2c: designware: always clear interrupts before enabling them
i2c: designware: fix RX FIFO overrun
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Barry Song <Baohua.Song@csr.com>
i2c: suppress lockdep warning on delete_device
Since commit 846f99749a the following lockdep
warning is thrown in case i2c device is removed (via delete_device sysfs
attribute) which contains subdevices (e.g. i2c multiplexer):
=============================================
[ INFO: possible recursive locking detected ]
3.8.7-0-sampleversion-fct #8 Tainted: G O
---------------------------------------------
bash/3743 is trying to acquire lock:
(s_active#110){++++.+}, at: [<ffffffff802b3048>] sysfs_hash_and_remove+0x58/0xc8
but task is already holding lock:
(s_active#110){++++.+}, at: [<ffffffff802b3cb8>] sysfs_write_file+0xc8/0x208
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(s_active#110);
lock(s_active#110);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by bash/3743:
#0: (&buffer->mutex){+.+.+.}, at: [<ffffffff802b3c3c>] sysfs_write_file+0x4c/0x208
#1: (s_active#110){++++.+}, at: [<ffffffff802b3cb8>] sysfs_write_file+0xc8/0x208
#2: (&adap->userspace_clients_lock/1){+.+.+.}, at: [<ffffffff80454a18>] i2c_sysfs_delete_device+0x90/0x238
#3: (&__lockdep_no_validate__){......}, at: [<ffffffff803dcc24>] device_release_driver+0x24/0x48
stack backtrace:
Call Trace:
[<ffffffff80575cc8>] dump_stack+0x8/0x34
[<ffffffff801b50fc>] __lock_acquire+0x161c/0x2110
[<ffffffff801b5c3c>] lock_acquire+0x4c/0x70
[<ffffffff802b60cc>] sysfs_addrm_finish+0x19c/0x1e0
[<ffffffff802b3048>] sysfs_hash_and_remove+0x58/0xc8
[<ffffffff802b7d8c>] sysfs_remove_group+0x64/0x148
[<ffffffff803d990c>] device_remove_attrs+0x9c/0x1a8
[<ffffffff803d9b1c>] device_del+0x104/0x1d8
[<ffffffff803d9c18>] device_unregister+0x28/0x70
[<ffffffff8045505c>] i2c_del_adapter+0x1cc/0x328
[<ffffffff8045802c>] i2c_del_mux_adapter+0x14/0x38
[<ffffffffc025c108>] pca954x_remove+0x90/0xe0 [pca954x]
[<ffffffff804542f8>] i2c_device_remove+0x80/0xe8
[<ffffffff803dca9c>] __device_release_driver+0x74/0xf8
[<ffffffff803dcc2c>] device_release_driver+0x2c/0x48
[<ffffffff803dbc14>] bus_remove_device+0x13c/0x1d8
[<ffffffff803d9b24>] device_del+0x10c/0x1d8
[<ffffffff803d9c18>] device_unregister+0x28/0x70
[<ffffffff80454b08>] i2c_sysfs_delete_device+0x180/0x238
[<ffffffff802b3cd4>] sysfs_write_file+0xe4/0x208
[<ffffffff8023ddc4>] vfs_write+0xbc/0x160
[<ffffffff8023df6c>] SyS_write+0x54/0xd8
[<ffffffff8013d424>] handle_sys64+0x44/0x64
The problem is already known for USB and PCI subsystems. The reason is that
delete_device attribute is defined statically in i2c-core.c and used for all
devices in i2c subsystem.
Discussion of original USB problem:
http://lkml.indiana.edu/hypermail/linux/kernel/1204.3/01160.html
Commit 356c05d58a introduced new macro to suppress
lockdep warnings for this special case and included workaround for USB code.
LKML discussion of the workaround:
http://lkml.indiana.edu/hypermail/linux/kernel/1205.1/03634.html
As i2c case is in principle the same, the same workaround could be used here.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do not use interruptible waits in an I2C driver; if a process uses
signals (eg, Xorg uses SIGALRM and SIGPIPE) then these signals can
cause the I2C driver to abort a transaction in progress by another
driver, which can cause that driver to fail. I2C drivers are not
expected to abort transactions on signals.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Duplicate the feature bits documentation in modinfo, as not every user
will read the driver's source code or documentation file.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is the same controller as on Intel Lynxpoint but the ACPI ID is
different (8086F41). Add support for this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the I2C bus is put to a low power state by an ACPI method it might pull
the SDA line low (as its power is removed). Once the bus is put to full
power state again, the SDA line is pulled back to high. This transition
looks like a STOP condition from the controller point-of-view which sets
STOP detected bit in its status register causing the driver to fail
subsequent transfers.
Fix this by always clearing all interrupts before we start a transfer.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
i2c_dw_xfer_msg() pushes a number of bytes to transmit/receive
to/from the bus into the TX FIFO.
For master-rx transactions, the maximum amount of data that can be
received is calculated depending solely on TX and RX FIFO load.
This is racy - TX FIFO may contain master-rx data yet to be
processed, which will eventually land into the RX FIFO. This
data is not taken into account and the function may request more
data than the controller is actually capable of storing.
This patch ensures the driver takes into account the outstanding
master-rx data in TX FIFO to prevent RX FIFO overrun.
Signed-off-by: Josef Ahmad <josef.ahmad@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
This is support for the ARM Chromebook, originally scheduled
as a "late" pull request. Since it's already late now, we
can combine this into the existing next/dt2 branch.
* late/dt:
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
Pull i2c changes from Wolfram Sang:
- an arbitration driver. While the driver is quite simple, it caused
discussion if we need additional arbitration on top of the one
specified in the I2C standard. Conclusion is that I accept a few
generic mechanisms, but not very specific ones.
- the core lost the detach_adapter() call. It has no users anymore and
was in the way for other cleanups. attach_adapter() is sadly still
there since there are users waiting to be converted.
- the core gained a bus recovery infrastructure. I2C defines a way to
recover if the data line is stalled. This mechanism is now in the
core and drivers can now pass some data to make use of it.
- bigger driver cleanups for designware, s3c2410
- removing superfluous refcounting from drivers
- removing Ben Dooks as second maintainer due to inactivity. Thanks
for all your work so far, Ben!
- bugfixes, feature additions, devicetree fixups, simplifications...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: xiic: must always write 16-bit words to TX_FIFO
i2c: octeon: use HZ in timeout value
i2c: octeon: Fix i2c fail problem when a process is terminated by a signal
i2c: designware-pci: drop superfluous {get|put}_device
i2c: designware-plat: drop superfluous {get|put}_device
i2c: davinci: drop superfluous {get|put}_device
MAINTAINERS: Ben Dooks is inactive regarding I2C
i2c: mux: Add i2c-arb-gpio-challenge 'mux' driver
i2c: at91: convert to dma_request_slave_channel_compat()
i2c: mxs: do error checking and handling in PIO mode
i2c: mxs: remove races in PIO code
i2c-designware: switch to use runtime PM autosuspend
i2c-designware: use usleep_range() in the busy-loop
i2c-designware: enable/disable the controller properly
i2c-designware: use dynamic adapter numbering on Lynxpoint
i2c-designware-pci: use managed functions pcim_* and devm_*
i2c-designware-pci: use dev_err() instead of printk()
i2c-designware: move to managed functions (devm_*)
i2c: remove CONFIG_HOTPLUG ifdefs
i2c: s3c2410: Add SMBus emulation for block read
...
The TX_FIFO register is 10 bits wide. The lower 8 bits are the data to be
written, while the upper two bits are flags to indicate stop/start.
The driver apparently attempted to optimize write access, by only writing a
byte in those cases where the stop/start bits are zero. However, we have
seen cases where the lower byte is duplicated onto the upper byte by the
hardware, which causes inadvertent stop/starts.
This patch changes the write access to the transmit FIFO to always be 16 bits
wide.
Signed off by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
I've been debugging the abnormal operation of i2c on octeon. If a process is
terminated by signal in the middle of i2c operation, next i2c read operation
which is done by another process was failed. So i changed to ignore signal in
the middle of i2c operation. After that the problem was not reproduced.
Signed-off-by: Eunbong Song <eunb.song@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Driver core already takes care of refcounting, no need to do this on
driver level again.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Sekhar Nori <nsekhar@ti.com>
The i2c-arb-gpio-challenge driver implements an I2C arbitration scheme
where masters need to claim the bus with a GPIO before they can start
a transaction. This should generally only be used when standard I2C
multimaster isn't appropriate for some reason (errata/bugs).
This driver is based on code that Simon Glass added to the i2c-s3c2410
driver in the Chrome OS kernel 3.4 tree. The current incarnation as a
mux driver is as suggested by Grant Likely. See
<https://patchwork.kernel.org/patch/1877311/> for some history.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Use generic DMA DT helper. Platforms booting with or without DT populated are
both supported.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In PIO mode we can end up with the same errors as in DMA mode, but as IRQs
are disabled there we have to check for them manually after each command.
Also don't use the big controller reset hammer when receiving a NAK from a
slave. It's sufficient to tell the controller to continue at a clean state.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit fixes the three following races in PIO code:
- The CTRL0 register is racy in itself, when programming transfer state and
run bit in the same cycle the hardware sometimes ends up using the state
from the last transfer. Fix this by programming state in one cycle, make
sure the write is flushed down APBX bus by reading back the reg and only
then trigger the run bit.
- Only clear the DMAREQ bit in DEBUG0 after the read/write to the data reg
happened. Otherwise we are racing with the hardware about who touches
the data reg first.
- When checking for completion of a transfer it's not sufficient to check
if the data engine finished, but also a check for i2c bus idle is needed.
In PIO mode we are really fast to program the next transfer after a finished
one, so the controller possibly tries to start a new transfer while the
clkgen engine is still busy writing the NAK/STOP from the last transfer to
the bus.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using autosuspend helps to reduce the resume latency in situations where
another I2C message is going to be started soon. For example with HID over
I2C touch panels we get several messages in a short period of time while
the touch panel is in use.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is not an atomic context so there is no need to use mdelay() but
instead use usleep_range().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The correct way to disable or enable the controller is to wait until the
DW_IC_ENABLE_STATUS register bit matches the bit we program into DW_IC_ENABLE
register. This procedure is described in the DesignWare I2C databook.
By doing this we can be sure that the controller is in correct state once
the function returns.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is not good idea to mix static and dynamic I2C adapter numbering. In
this particular case on Lynxpoint we had graphics I2C adapter which took
the first numbers preventing the designware I2C driver from using the
adapter numbers it preferred.
Since Lynxpoint support was just introduced and there is no hardware available
outside Intel we can fix this by switching to use dynamic adapter numbering
instead of static.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With dev_err() we can get the device instance printed as well and is pretty
much standard to use dev_* macros in the drivers anyway. In addition
correct the indentation of probe() arguments.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller and tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
CONFIG_HOTPLUG is going away as an option, cleanup CONFIG_HOTPLUG
ifdefs in i2c files.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBus read and write are supported by the emulation layer of i2c
framework if the controller doesn't have SMBus features.
I2C_M_RECV_LEN flag is used to let i2c drivers know rx length is not
yet determined but will be read to the first byte in rx buffer.
s3c2410 doesn't handle this flag. So only one byte is read from slave.
There fore following two features are added to the driver code.
1. skip rx length check if I2C_M_RECV_LEN is set and the length is 1.
2. add actual bytes to the rx length after reading first bytes if
I2C_M_RECV_LEN.
I2C_M_RECV_LEN is only set for SMBus command. So this code does not
affect legacy codes which only use i2c command for s3c2410.
Signed-off-by: Jaemin Yoo <jmin.yoo@samsung.com>
Tested-by: Prasanna Kumar <prasanna.ps@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With the generic DMA device tree helper supported by mxs-dma driver,
client devices only need to call dma_request_slave_channel() for
requesting a DMA channel from dmaengine.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
The ACPI handle of struct i2c_adapter's dev member should not be
set, because this causes that struct i2c_adapter to be associated
with the ACPI device node corresponding to its parent as the
second "physical_device", which is incorrect (this happens during
the registration of struct i2c_adapter). Consequently,
acpi_i2c_register_devices() should use the ACPI handle of the
parent of the struct i2c_adapter it is called for rather than the
struct i2c_adapter's ACPI handle (which should be NULL).
Make that happen and modify the i2c-designware-platdrv driver,
which currently is the only driver for ACPI-enumerated I2C
controller chips, not to set the ACPI handle for the
struct i2c_adapter it creates.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
i2c_del_mux_adapter always returns 0 and none of it current users check its
return value anyway. It is also an essential requirement of the Linux device
driver model, that functions which may be called from a device's remove callback
to free resources provided by the device, are not allowed to fail. This is the
case for i2c_del_mux_adapter(), so make its return type void to make the
fact that it won't fail explicit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_del_mux_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore its return
value and assume that it will always succeed (which it will). A subsequent
patch will make the return type of i2c_del_mux_adapter() void.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_del_adapter() is usually called from a drivers remove callback. The Linux
device driver model does not allow the remove callback to fail and all resources
allocated in the probe callback need to be freed, as well as all resources which
have been provided to the rest of the kernel(for example a I2C adapter) need to
be revoked. So any function revoking such resources isn't allowed to fail
either. i2c_del_adapter() adheres to this requirement and will never fail. But
i2c_del_adapter()'s return type is int, which may cause driver authors to think
that it can fail. This led to code constructs like:
ret = i2c_del_adapter(...);
BUG_ON(ret);
Since i2c_del_adapter() always returns 0 the BUG_ON is never hit and essentially
becomes dead code, which means it can be removed. Making the return type of
i2c_del_adapter() void makes it explicit that the function will never fail and
should prevent constructs like the above from re-appearing in the kernel code.
All callers of i2c_del_adapter() have already been updated in a previous patch
to ignore the return value, so the conversion of the return type from int to
void can be done without causing any build failures.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_del_adapter() always returns 0. So all checks testing whether it will be
non zero will always evaluate to false and the conditional code is dead code.
This patch updates all callers of i2c_del_mux_adapter() to ignore the return
value and assume that it will always succeed (which it will). In a subsequent
patch the return type of i2c_del_adapter() will be made void.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently i2c_del_adapter() returns -EINVAL when it gets an adapter which is not
registered. But none of the users of i2c_del_adapter() depend on this behavior,
so for the sake of being able to sanitize the return type of i2c_del_adapter
argue, that the purpose of i2c_del_adapter() is to remove an I2C adapter from
the system. If the adapter is not registered in the first place this becomes a
no-op. So we can return success without having to do anything.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The detach_adapter callback has been deprecated for quite some time and has no
user left. Keeping it alive blocks other cleanups, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the code to use devm_* API so that driver core will manage
resources.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since we have generic i2c bus recover routines now, these custom ones
need to be renamed to fix the namespace clash. Proper conversion needs
to be done by someone who has access to the hardware.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
gpio_direction_output() may fail, check for that and deal with it
appropriately. Also log an error message if gpio_request() fails.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
GPIOs may not be available immediately when i2c-gpio looks for them.
Implement support for deferred probing so that probing can be
attempted again later when GPIO pins are finally available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make them conform more to established standards.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The register definitions are only used in the driver itself.
This also removes the last dependency on plat/ includes from the
i2c driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Delete the header that defines it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit: "i2c-core: dt: Pick i2c bus number from i2c alias if
present" adds support for automatically picking the bus number based
on the alias ID. Remove the now unnecessary code from i2c-pxa that
did the same thing.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c bus recovery infrastructure to i2c adapters as specified in the i2c
protocol Rev. 03 section 3.1.16 titled "Bus clear".
http://www.nxp.com/documents/user_manual/UM10204.pdf
Sometimes during operation i2c bus hangs and we need to give dummy clocks to
slave device to start the transfer again. Now we may have capability in the bus
controller to generate these clocks or platform may have gpio pins which can be
toggled to generate dummy clocks. This patch supports both.
This patch also adds in generic bus recovery routines gpio or scl line based
which can be used by bus controller. In addition controller driver may provide
its own version of the bus recovery routine.
This doesn't support multi-master recovery for now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[wsa: changed gpio type to int and minor reformatting]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows you to get the equivalent functionality of
i2c_add_numbered_adapter() with all data in the device tree and no
special case code in your driver. This is a common device tree
technique.
For quick reference, the FDT syntax for using an alias to provide an
ID looks like:
aliases {
i2c0 = &i2c_0;
i2c1 = &i2c_1;
};
Signed-off-by: Doug Anderson <dianders@chromium.org>
[wsa: removed one check from static function. We know our callers]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c fixes from Wolfram Sang:
"One bugfix for the tegra driver. Two updates regarding email
addresses and MAINTAINERS which I like to have up-to-date so people
can be reached immediately. While we are here, there is on PCI_ID
addition."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer entry for atmel i2c driver
i2c: Fix my e-mail address in drivers and documentation
i2c: iSMT: add Intel Avoton DeviceIDs
i2c: tegra: check the clk_prepare_enable() return value
This patch adds the iSMT SMBus Controller DeviceIDs for the Intel Avoton SOC.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
NVIDIA's Tegra SoC allows read/write of controller register only
if controller clock is enabled. System hangs if read/write happens
to registers without enabling clock.
clk_prepare_enable() can be fail due to unknown reason and hence
adding check for return value of this function. If this function
success then only access register otherwise return to caller with
error.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Remove !S390 dependency from i2c Kconfig, since s390 now supports PCI, HAS_IOMEM
and HAS_DMA, however we need to add a couple of GENERIC_HARDIRQS dependecies to
fix compile and link errors like these:
ERROR: "devm_request_threaded_irq" [drivers/i2c/i2c-smbus.ko] undefined!
ERROR: "devm_request_threaded_irq" [drivers/i2c/busses/i2c-ocores.ko] undefined!
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
MAX_IDR_MASK is another weirdness in the idr interface. As idr covers
whole positive integer range, it's defined as 0x7fffffff or INT_MAX.
Its usage in idr_find(), idr_replace() and idr_remove() is bizarre.
They basically mask off the sign bit and operate on the rest, so if
the caller, by accident, passes in a negative number, the sign bit
will be masked off and the remaining part will be used as if that was
the input, which is worse than crashing.
The constant is visible in idr.h and there are several users in the
kernel.
* drivers/i2c/i2c-core.c:i2c_add_numbered_adapter()
Basically used to test if adap->nr is a negative number which isn't
-1 and returns -EINVAL if so. idr_alloc() already has negative
@start checking (w/ WARN_ON_ONCE), so this can go away.
* drivers/infiniband/core/cm.c:cm_alloc_id()
drivers/infiniband/hw/mlx4/cm.c:id_map_alloc()
Used to wrap cyclic @start. Can be replaced with max(next, 0).
Note that this type of cyclic allocation using idr is buggy. These
are prone to spurious -ENOSPC failure after the first wraparound.
* fs/super.c:get_anon_bdev()
The ID allocated from ida is masked off before being tested whether
it's inside valid range. ida allocated ID can never be a negative
number and the masking is unnecessary.
Update idr_*() functions to fail with -EINVAL when negative @id is
specified and update other MAX_IDR_MASK users as described above.
This leaves MAX_IDR_MASK without any user, remove it and relocate
other MAX_IDR_* constants to lib/idr.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: "Marciniszyn, Mike" <mike.marciniszyn@intel.com>
Cc: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Wolfram Sang <wolfram@the-dreams.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Wolfram Sang <wolfram@the-dreams.de>
Tested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Pull i2c updates from Wolfram Sang:
"Highlights:
- new drivers for Intel ismt & Broadcom bcm2835
- a number of drivers got support for more variants and mostly got
cleaned up on the way (sis630, i801, at91, tegra, designware)
- i2c got rid of all *_set_drvdata(..., NULL) on remove/probe failure
- removed the i2c_smbus_process_call from the core since there are no
users
- mxs can now switch between PIO and DMA depending on the message
size and the bus speed can now be arbitrary
In addition, there is the usual bunch of fixes, cleanups, devm_*
conversions, etc"
Fixed conflict (and buggy devm_* conversion) in i2c-s3c2410.c
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (39 commits)
i2c: Remove unneeded xxx_set_drvdata(..., NULL) calls
i2c: pxa: remove incorrect __exit annotations
i2c: ocores: Fix pointer to integer cast warning
i2c: tegra: remove warning dump if timeout happen in transfer
i2c: fix i2c-ismt.c printk format warning
i2c: i801: Add Device IDs for Intel Wellsburg PCH
i2c: add bcm2835 driver
i2c: ismt: Add Seth and Myself as maintainers
i2c: sis630: checkpatch cleanup
i2c: sis630: display unsigned hex
i2c: sis630: use hex to constants for SMBus commands
i2c: sis630: fix behavior after collision
i2c: sis630: clear sticky bits
i2c: sis630: Add SIS964 support
i2c: isch: Add module parameter for backbone clock rate if divider is unset
i2c: at91: fix unsed variable warning when building with !CONFIG_OF
i2c: Adding support for Intel iSMT SMBus 2.0 host controller
i2c: sh_mobile: don't send a stop condition by default inside transfers
i2c: sh_mobile: eliminate an open-coded "goto" loop
i2c: sh_mobile: fix timeout error handling
...
This is a larger set of new functionality for the existing SoC families,
including:
* vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850
* prima2 gains support for the "marco" SoC family, its SMP based cousin
* tegra gains support for the new Tegra4 (Tegra114) family
* socfpga now supports a newer version of the hardware including SMP
* i.mx31 and bcm2835 are now using DT probing for their clocks
* lots of updates for sh-mobile
* OMAP updates for clocks, power management and USB
* i.mx6q and tegra now support cpuidle
* kirkwood now supports PCIe hot plugging
* tegra clock support is updated
* tegra USB PHY probing gets implemented diffently
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PRrg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
There is simply no reason to be manually setting the private driver
data to NULL in the remove/fail to probe cases. This is just extra
cruft code that can be removed.
A few notes:
* Nothing relies on drvdata being set to NULL.
* The __device_release_driver() function eventually calls
dev_set_drvdata(dev, NULL) anyway, so there's no need to do it
twice.
* I verified that there were no cases where xxx_get_drvdata() was
being called in these drivers and checking for / relying on the NULL
return value.
This could be cleaned up kernel-wide but for now just take the baby
step and remove from the i2c subsystem.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
The remove() methods should not be marked __exit unless we are using
platform_driver_probe() which disables unbinding device from driver
via sysfs.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
After commit a000b8c1 [i2c: ocores: Add support for the GRLIB port of the
controller and use function pointers for getreg and setreg function],
compiling i2c-ocores.c for 64-bit gives the following warning:
drivers/i2c/busses/i2c-ocores.c: In function 'ocores_i2c_of_probe':
drivers/i2c/busses/i2c-ocores.c:334:15: warning: cast from pointer to integer of different size
Fix it by casting the pointer to long.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If timeout error occurs in the i2c transfer then it was dumping warning
of call stack.
Remove the warning dump as there is may be possibility that some slave
devices are busy and not responding the i2c communication.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Fix printk format warning. dma_addr_t can be 32-bit or 64-bit,
so cast it to long long for printing. This also matches the
printk format specifier that is already used.
drivers/i2c/busses/i2c-ismt.c:532:3: warning: format '%llX' expects argument of type 'long long unsigned int', but argument 4 has type 'dma_addr_t' [-Wformat]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
This patch adds the SMBus Device IDs for the Intel Wellsburg PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
This implements a very basic I2C host driver for the BCM2835 SoC. Missing
features so far are:
* 10-bit addressing.
* DMA.
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
This patch corrects checkpatch errors.
The changes has also been removed as it has less meaning with version
control tools.
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
This patch corrects the display of the acpi_base unsigned hex value.
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
This patch replaces hexadecimal values by constants for SMBus commands.
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Datasheet on collision:
SMBus Collision (SMBCOL_STS)
This bit is set when a SMBus Collision condition occurs and
SMBus Host loses in the bus arbitration. The software should
clear this bit and re-start SMBus operation.
As the status will be cleared in transaction_end, we can remove the
sis630_write and prepare to return -EAGAIN to retry.
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
The sticky bits must be cleared at the end of the transaction by writing
a 1 to all fields.
Datasheet:
SMBus Status (SMB_STS)
The following registers are all sticky bits and only can be
cleared by writing a one to their corresponding fields.
Signed-off-by: Amaury Decrême <amaury.decreme@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
It was observed the Host Clock Divider was not written by the driver. It
was still set to (default) 0, if not already set by BIOS, which caused
garbage on SMBus.
This driver adds a parameters which is used to calculate the divider
appropriately for a default bitrate of 100 KHz. This new divider is only
applied if the clock divider is still default 0.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Commit 70d46a2 "i2c: at91: add dt support to i2c-at91"
added DT only support for at91sam9x5. Building i2c-at91
without CONFIG_OF now warns about at91sam9x5_config as
being unused.
drivers/i2c/busses/i2c-at91.c:556:30: warning: 'at91sam9x5_config' defined but not used [-Wunused-variable]
Move at91sam9x5_config under the defined(CONFIG_OF)
guard as new AT91 SoCs will be DT only.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
The iSMT (Intel SMBus Message Transport) supports multi-master I2C/SMBus,
as well as IPMI. It's operation is DMA-based and utilizes descriptors to
initiate transactions on the bus.
The iSMT hardware can act as both a master and a target, although this
driver only supports being a master.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Bill Brown <bill.e.brown@intel.com>
Tested-by: Seth Heasley <seth.heasley@intel.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
By default there should be no stop bit on I2C between single messages
within transfers. Fix the driver to comply and only send a stop bit at
the end of transfers or if I2C_M_STOP is set.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Eliminate an open-coded "goto" loop by introducing a function.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
In a timeout case return an error immediately from the driver's
.master_xfer() method, instead of continuing and letting higher layers
fail.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
This patch drops the i2c timing tables from this driver and instead
derives the timing based from the requested clock sleep. The timing
tables were completely wrong anyway when observed on a scope.
This new algorithm is also only derived by using a scope, but it seems
to produce much more accurate result.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
[wsa: changed messages from dev_err to dev_warn]
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
This patch adds the PCU SMBus DeviceID for the Intel Avoton SOC.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9hz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
Migrate Tegra clock support to drivers/clk/tegra, this involves
moving:
1. definition of tegra_cpu_car_ops to clk.c
2. definition of reset functions to clk-peripheral.c
3. change parent of cpu clock.
4. Remove legacy clock initialization.
5. Initialize clocks using DT.
6. Remove all instance of mach/clk.h
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: use to_clk_periph_gate().]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add support for the PIO mode and mixed PIO/DMA mode support. The mixed
PIO/DMA is the default mode of operation. This shall leverage overhead
that the driver creates due to setting up DMA descriptors even for very
short transfers.
The current boundary between PIO/DMA 8 bytes, transfers shorter than 8
bytes are transfered by PIO, longer transfers use DMA. The performance
of write transfers remains unchanged, while there is a minor improvement
of read performance. Reading 16KB EEPROM with DMA-only operations gives
a read speed of 39.5KB/s, while with then new mixed-mode the speed is
blazing 40.6KB/s.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
err_cpufreq label is now used only once. It can be removed and related
code can be moved to the caller location.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
In i2c-s3c2410 driver probe, only s3c24xx_i2c_init() needs the I2C clock
to be enabled. Moving clk_prepare_enable() and clk_disable_unprepare()
calls to around this function simplifies the return path of probe call.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
i2c-s3c2410 driver is modified to use devm_clk_get()
and devm_request_irq(). This also simplifies the
return path in driver's probe.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
err_noclk label redirects to a simple return statement. Move the
return statement to the caller location and remove the label.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
cppcheck rightfully reports those as "reassigned a value before the old
one has been used."
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Amend the I2C nomadik pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an i2c transfer
- "idle" after initial default, after resume default, and after each
i2c xfer
- "sleep" on suspend()
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle, and for runtime cases inbetween
I2C transfers.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[wsa: fixed braces on one else-branch]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
NVIDIA's Tegra114 has following enhanced feature in i2c controller:
- Enable/disable control for per packet transfer complete interrupt.
Earlier SoCs could not disable this.
- Single clock source for standard/fast and HS mode clock speed.
The clock divisor for fast/standard mode is added into the i2c
controller to meet the HS and standard/fast mode of clock speed
from single source.
Add support for the above feature to make it functional on T114 SOCs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Intel Lynxpoint has two I2C controllers. These controllers are enumerated
from ACPI namespace with IDs INT33C2 and INT33C3. Add support for these to
the I2C DesignWare platform driver.
This is based on the work of Dirk Brandewie.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
In order to save power the device should be put to low power states
whenever it is not being used. We implement this by enabling minimal
runtime PM support.
There isn't much to do for the device itself as it is disabled once the
last transfer is completed but subsystem/domain runtime PM hooks can save
more power by power gating the device etc.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
If IC_EMPTYFIFO_HOLD_MASTER_EN is set to one, the DesignWare I2C controller
doesn't generate STOP on the bus when the FIFO is empty. This violates the
rules of Linux I2C stack as it requires that the STOP is issued once the
i2c_transfer() is finished.
However, there is no way to detect this from the hardware registers, so we
must make sure that the STOP bit is always set once the last byte of the
last message is transferred.
This patch is based on the work of Dirk Brandewie.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
avoid these checkpatch.pl issues :
- ERROR: "foo * bar" should be "foo *bar"
- ERROR: switch and case should be at the same indent
- ERROR: "(foo*)" should be "(foo *)"
- ERROR: do not use assignment in if condition
- ERROR: space required before the open parenthesis '('
- WARNING: suspect code indent for conditional statements
- WARNING: quoted string split across lines
- WARNING: space prohibited between function name and open parenthesis '('
- WARNING: line over 80 characters
also add spaces around some "+", "=", "*"
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
i2c_smbus_process_call has no users in the kernel, so this can be
removed. Documentation for the same has been updated accordingly.
Fixes following sparse warning.
drivers/i2c/i2c-core.c:1871:5: warning: symbol 'i2c_smbus_process_call'
was not declared. Should it be static?
[wsa: updated the documentation]
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The second argument of ACPI driver .remove() operation is only used
by the ACPI processor driver and the value passed to that driver
through it is always available from the given struct acpi_device
object's removal_type field. For this reason, the second ACPI driver
.remove() argument is in fact useless, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver can also be built as a module so add MODULE_LICENSE for it. In
addition add MODULE_DESCRIPTION as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Commit 0bdfe0cb80 (i2c: omap: sanitize
exit path) changed the interrupt handler to exit early and complete
the transfer after the draining IRQ is handled. As a result, the ARDY
may not be cleared properly, and it may cause all future I2C transfers
to timeout with "timeout waiting for bus ready". This is reproducible
at least with N900 when twl4030_gpio makes a long write (> FIFO size)
during the probe (http://marc.info/?l=linux-omap&m=135818882610432&w=2).
The fix is to continue until we get ARDY interrupt that completes the
transfer. Tested with 3.8-rc4 + N900: 20 boots in a row without errors;
without the patch the problem triggers after few reboots.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The errata handling function acks wrong interrupt in case of "Arbitration
lost". Fix it.
Discovered during code review, the real impact of the bug is unknown.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
sizeof when applied to a pointer typed expression gives the size of
the pointer
The semantic patch that makes this output is available
in scripts/coccinelle/misc/noderef.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
in probe() entry of i2c_driver, set the of node of adapter and
call of_i2c_register_devices to register all i2c_client from
dt child-nodes
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
cmd_err is used to handle error code, so it should not be unsigned.
This fixes the following warning when building with W=1 option:
drivers/i2c/busses/i2c-mxs.c: In function 'mxs_i2c_xfer_msg':
drivers/i2c/busses/i2c-mxs.c:331:19: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The init_completion() call does reinit not only the variable carrying
the flag that the completion finished, but also initialized the
waitqueue associated with the completion. On the contrary, the
INIT_COMPLETION() call only reinits the flag.
In case there was anything still stuck in the waitqueue, subsequent call
to init_completion() would be able to create possible race condition. This
patch uses the proper function and moves init_completion() into .probe() call
of the driver, to be issued only once.
Note that such scenario is impossible, since two threads can never enter the
mxs_i2c_xfer_msg(), since whole this section is protected by mutex in I2C core.
This by no means allows this issue to exit though.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Stephen Warren <swarren@nvidia.com>
CC: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com> (for ocores and mux-gpio)
Acked-by: Havard Skinnemoen <hskinnemoen@gmail.com> (for i2c-gpio)
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> (for puf3)
Acked-by: Barry Song <baohua.song@csr.com> (for sirf)
Reviewed-by: Jean Delvare <khali@linux-fr.org>
[wsa: Fixed "foo* bar" flaws while we are here]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pull i2c-embedded changes from Wolfram Sang:
- CBUS driver (an I2C variant)
- continued rework of the omap driver
- s3c2410 gets lots of fixes and gains pinctrl support
- at91 gains DMA support
- the GPIO muxer gains devicetree probing
- typical fixes and additions all over
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
i2c: at91: add dma support
i2c: at91: change struct members indentation
i2c: at91: fix compilation warning
i2c: mxs: Do not disable the I2C SMBus quick mode
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Remove recently introduced performance overheads
i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
i2c: s3c2410: Add fix for i2c suspend/resume
i2c: s3c2410: Fix code to free gpios
i2c: i2c-cbus-gpio: introduce driver
i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
i2c: ocores: Add irq support for sparc
i2c: omap: Move the remove constraint
ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
i2c: s3c2410: do not special case HDMIPHY stuck bus detection
i2c: s3c2410: use exponential back off while polling for bus idle
i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
i2c: s3c2410: grab adapter lock while changing i2c clock
i2c: s3c2410: Add support for pinctrl
...
We have several new drivers, most of the time coming with their sub devices
drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap I/O and IRQ
APIs and a conversion to the recently added PWM framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have Mark's
wm5xxx and wm8xxx patchset.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=F790
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFS update from Samuel Ortiz:
"This is the MFD patch set for the 3.8 merge window.
We have several new drivers, most of the time coming with their sub
devices drivers:
- Austria Microsystem's AS3711
- Nano River's viperboard
- TI's TPS80031, AM335x TS/ADC,
- Realtek's MMC/memstick card reader
- Nokia's retu
We also got some notable cleanups and improvements:
- tps6586x got converted to IRQ domains.
- tps65910 and tps65090 moved to the regmap IRQ API.
- STMPE is now Device Tree aware.
- A general twl6040 and twl-core cleanup, with moves to the regmap
I/O and IRQ APIs and a conversion to the recently added PWM
framework.
- sta2x11 gained regmap support.
Then the rest is mostly tiny cleanups and fixes, among which we have
Mark's wm5xxx and wm8xxx patchset."
Far amount of annoying but largely trivial conflicts. Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.
* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
mfd: tps6507x: Convert to devm_kzalloc
mfd: stmpe: Update DT support for stmpe driver
mfd: wm5102: Add readback of DSP status 3 register
mfd: arizona: Log if we fail to create the primary IRQ domain
mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
mfd: tps80031: Add terminating entry for tps80031_id_table
mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
mfd: wm5102: Add tuning for revision B
mfd: arizona: Defer patch initialistation until after first device boot
mfd: tps65910: Fix wrong ack_base register
mfd: tps65910: Remove unused data
mfd: stmpe: Get rid of irq_invert_polarity
mfd: ab8500-core: Fix invalid free of devm_ allocated data
mfd: wm5102: Mark DSP memory regions as volatile
mfd: wm5102: Correct default for LDO1_CONTROL_2
mfd: arizona: Register haptics devices
mfd: wm8994: Make current device behaviour the default
mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
mfd: Fix stmpe.c build when OF is not enabled
mfd: jz4740-adc: Use devm_kzalloc
...
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I did not receive a single bug report after interrupt support was
added for a limited number of chips. So I'd say the code is good and
should be enabled for all supported chips, that is: ICH5 and later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Add support for probing slave devices parsed from the device tree.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to be
part of the multiplatform support -- the first "big" SoC that is moved
over (more multiplatform work comes in a separate branch later during
the merge window).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zfPd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups on various subarchitectures from Olof Johansson:
"Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to
be part of the multiplatform support -- the first "big" SoC that is
moved over (more multiplatform work comes in a separate branch later
during the merge window)."
Conflicts fixed as per Olof, including a silent semantic one in
arch/arm/mach-omap2/board-generic.c (omap_prcm_restart() was renamed to
omap3xxx_restart(), and a new user of the old name was added).
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (189 commits)
ARM: omap: fix typo on timer cleanup
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
...
* Introduction of device PM QoS flags.
* ACPI device power management update allowing subsystems other than
PCI to use it more easily.
* ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
* ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
* ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
* Introduction of acpi_handle_<level>() messaging macros and ACPI-based CPU
hot-remove support from Toshi Kani.
* ACPI EC updates from Feng Tang.
* cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
* cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
* Support for using multiple cpuidle drivers at the same time and cpuidle
cleanups from Daniel Lezcano.
* devfreq updates from Nishanth Menon and others.
* cpupower update from Thomas Renninger.
* Fixes and small cleanups all over the place.
--
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=6OEP
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
- Introduction of device PM QoS flags.
- ACPI device power management update allowing subsystems other than
PCI to use it more easily.
- ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
- ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
- ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
- Introduction of acpi_handle_<level>() messaging macros and ACPI-based
CPU hot-remove support from Toshi Kani.
- ACPI EC updates from Feng Tang.
- cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
- cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
- Support for using multiple cpuidle drivers at the same time and
cpuidle cleanups from Daniel Lezcano.
- devfreq updates from Nishanth Menon and others.
- cpupower update from Thomas Renninger.
- Fixes and small cleanups all over the place.
* tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (196 commits)
mmc: sdhci-acpi: enable runtime-pm for device HID INT33C6
ACPI: add Haswell LPSS devices to acpi_platform_device_ids list
ACPI: add documentation about ACPI 5 enumeration
pnpacpi: fix incorrect TEST_ALPHA() test
ACPI / PM: Fix header of acpi_dev_pm_detach() in acpi.h
ACPI / video: ignore BIOS initial backlight value for HP Folio 13-2000
ACPI : do not use Lid and Sleep button for S5 wakeup
ACPI / PNP: Do not crash due to stale pointer use during system resume
ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklist
ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set
spi / ACPI: add ACPI enumeration support
gpio / ACPI: add ACPI support
PM / devfreq: remove compiler error with module governors (2)
cpupower: IvyBridge (0x3a and 0x3e models) support
cpupower: Provide -c param for cpupower monitor to schedule process on all cores
cpupower tools: Fix warning and a bug with the cpu package count
cpupower tools: Fix malloc of cpu_info structure
cpupower tools: Fix issues with sysfs_topology_read_file
cpupower tools: Fix minor warnings
cpupower tools: Update .gitignore for files created in the debug directories
...
Bug fixes, little cleanups, and documentation changes. The most invasive
thing here touches a bunch of the arch directories to use a common build
rule for .dtb files. There are no major changes to functionality here
other than a ew new helper functions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LB3n
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull device tree changes from Grant Likely:
"Here are the DT changes I've got queued up for v3.8. As described
below, there are a lot of bug fixes here and documentation updates but
nothing major:
Bug fixes, little cleanups, and documentation changes. The most
invasive thing here touches a bunch of the arch directories to use a
common build rule for .dtb files. There are no major changes to
functionality here other than a few new helper functions."
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
arm64: Fix the dtbs target building
mtd: nand: davinci: fix the binding documentation
rtc: rtc-mv: Add the device tree binding documentation
devicetree/bindings: Move gpio-leds binding into leds directory
of/vendor-prefixes: add Imagination Technologies
microblaze: use new common dtc rule
c6x: use new common dtc rule
openrisc: use new common dtc rule
arm64: Add dtbs target for building all the enabled dtb files
arm64: use new common dtc rule
ARM: dt: change .dtb build rules to build in dts directory
kbuild: centralize .dts->.dtb rule
Fix build when CONFIG_W1_MASTER_GPIO=m b exporting "allnodes"
of/spi: Honour "status=disabled" property of device
of_mdio: Honour "status=disabled" property of device
of_i2c: Honour "status=disabled" property of device
powerpc: Fix fallout from device_node->name constification
of: add 'const' for of_parse_phandle parameter *np
Documentation: correct of_platform_populate() argument list
script: dtc: clean generated files
...
The OMAP_I2C_FLAG_RESET_REGS_POSTIDLE is not used anymore
in the i2c driver. Remove the flag.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Add dma support for Atmel TWI which is available on sam9x5 and later.
When using dma for reception, you have to read only n-2 bytes. The last
two bytes are read manually. Don't doing this should cause to send the
STOP command too late and then to get extra data in the receive
register.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Replace tabs for struct members indentation by space to minimise line changes
when adding new members which would require extra tabs to keep alignment.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch fixes the following warning:
drivers/i2c/busses/i2c-at91.c: In function ‘at91_twi_get_driver_data’:
drivers/i2c/busses/i2c-at91.c:411:3: warning: return discards ‘const’ qualifier from pointer target type [enabled by default]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pull i2c fixes from Wolfram Sang:
"Bugfixes for the i2c subsystem.
Except for a few one-liners, there is mainly one revert because of an
overlooked dependency. Since there is no linux-next at the moment, I
did some extra testing, and all was fine for me."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Fix code to free gpios
i2c: omap: ensure writes to dev->buf_len are ordered
Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
i2c: at91: fix SMBus quick command
ACPI 5 introduced I2cSerialBus resource that makes it possible to enumerate
and configure the I2C slave devices behind the I2C controller. This patch
adds helper functions to support I2C slave enumeration.
An ACPI enabled I2C controller driver only needs to call acpi_i2c_register_devices()
in order to get its slave devices enumerated, created and bound to the
corresponding ACPI handle.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Properly terminate the DMA transfer in case the DMA PIO transfer
or setup fails for any reason.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
There is no reason to disable the I2C SMBus quick mode on this
IP block. Enable it. This essentially fixes the problem with the
"i2c-detect" command for probing the bus.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Properly terminate the DMA transfer in case the DMA PIO transfer
or setup fails for any reason.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The changes in "i2c-s3c2410: use exponential back off while polling for
bus idle" remove the initial busy wait for I2C transfers to complete and
replace it with usleep_range() calls which will schedule.
Since for older SoCs I2C transfers would usually complete within an
extremely small number of CPU cycles there is a win from not having to
schedule. This happens because on the older SoCs the cores run at a
smaller multiple of the speeds that the I2C bus is operating at; on more
modern SoCs the busy wait is less likely to be effective.
Fix the issue by restoring the busy wait, reducing the number of spins
from 20 to 3 which covers the overwhelming majority of I2C transfers on
the SoCs where the busy wait is effective.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This moves the grlib set and get functions into the #ifdef CONFIG_OF block to
avoid warnings of unimplemented functions when compiling with -Wunused-function
when CONFIG_OF is not defined.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This adds the mfd cell to use the i2c part of the Nano River Technologies
viperboard as i2c master.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
"Whether" is misspelled in various comments across the tree; this
fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Store the requested gpios so that they can be freed on error/removal.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The I2C driver makes a gpio_request during initialization. This request
happens again on resume and fails due to the earlier successful request.
Re-factor the code to only initialize the gpios during probe.
Errors on resume without this:
[ 16.020000] s3c-i2c s3c2440-i2c.0: gpio [42] request failed
[ 16.020000] s3c-i2c s3c2440-i2c.1: gpio [44] request failed
[ 16.020000] s3c-i2c s3c2440-i2c.2: gpio [6] request failed
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Store the requested gpios so that they can be freed on error/removal.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Add i2c driver to enable access to devices behind CBUS on Nokia Internet
Tablets.
The patch also adds CBUS I2C configuration for N8x0 which is one of the
users of this driver.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The registers in the GRLIB port of the controller are 32-bit and in big endian
byte order. The PRELOW and PREHIGH registers are merged into one register. The
subsequent registers have their offset decreased accordingly. Hence the register
access needs to be handled in a non-standard manner using custom getreg and
setreg functions.
Add setreg and getreg functions for different register widths and let oc_setreg
and oc_getreg use function pointers to call the appropriate functions.
A type is added as the data of the of match table entries. A new entry with a
different compatible string is added to the table. The type of that entry
triggers usage of the custom grlib functions by setting the setreg and getreg
function pointers.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Add sparc support by using platform_get_irq instead of platform_get_resource.
There are no platform resources of type IORESOURCE_IRQ for sparc, but
platform_get_irq works for sparc. In the non-sparc case platform_get_irq
internally uses platform_get_resource.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently we just queue the transfer and release the
qos constraints, however we do not wait for the transfer
to complete to release the constraint. Move the remove
constraint after the bus busy as we are sure that the
transfers are completed by then.
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Commit "i2c-s3c2410: Add HDMIPHY quirk for S3C2440" added support for
HDMIPHY with some special handling in s3c24xx_i2c_set_master:
"due to unknown reason (probably HW bug in HDMIPHY and/or the controller)
a transfer fails to finish. The controller hangs after sending the last
byte, the workaround for this bug is resetting the controller after each
transfer"
The "unknown reason" was that the proper sequence for generating a STOP
condition wasn't being followed as per the datasheet. Since this is fixed
by "PATCH: i2c-s3c2410: do not generate STOP for QUIRK_HDMIPHY buses",
remove the special handling.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Usually, the i2c controller has finished emitting the i2c STOP before the
driver reaches the bus idle polling loop. Optimize for this most common
case by reading IICSTAT first and potentially skipping the loop.
If the cpu is faster than the hardware, we wait for bus idle in a polling
loop. However, since the duration of one iteration of the loop is
dependent on cpu freq, and this i2c IP is used on many different systems,
use a time based loop timeout (5 ms).
We would like very low latencies to detect bus idle for the normal
'fast' case. However, if a device is slow to release the bus for some
reason, it could hold off the STOP generation for up to several
milliseconds. Rapidly polling for bus idle would seriously load the CPU
while waiting for it to release the bus. So, use a partial exponential
backoff as a compromise between idle detection latency and cpu load.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The datasheet says that the STOP sequence should be:
1) I2CSTAT.5 = 0 - Clear BUSY (or 'generate STOP')
2) I2CCON.4 = 0 - Clear IRQPEND
3) Wait until the stop condition takes effect.
4*) I2CSTAT.4 = 0 - Clear TXRXEN
Where, step "4*" is only for buses with the "HDMIPHY" quirk.
However, after much experimentation, it appears that:
a) normal buses automatically clear BUSY and transition from
Master->Slave when they complete generating a STOP condition.
Therefore, step (3) can be done in doxfer() by polling I2CCON.4
after starting the STOP generation here.
b) HDMIPHY bus does neither, so there is no way to do step 3.
There is no indication when this bus has finished generating STOP.
In fact, we have found that as soon as the IRQPEND bit is cleared in
step 2, the HDMIPHY bus generates the STOP condition, and then immediately
starts transferring another data byte, even though the bus is supposedly
stopped. This is presumably because the bus is still in "Master" mode,
and its BUSY bit is still set.
To avoid these extra post-STOP transactions on HDMI phy devices, we just
disable Serial Output on the bus (I2CSTAT.4 = 0) directly, instead of
first generating a proper STOP condition. This should float SDA & SCK
terminating the transfer. Subsequent transfers start with a proper START
condition, and proceed normally.
The HDMIPHY bus is an internal bus that always has exactly two devices,
the host as Master and the HDMIPHY device as the slave. Skipping the STOP
condition has been tested on this bus and works.
Also, since we disable the bus directly from the isr, we can skip the bus
idle polling loop at the end of doxfer().
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
We probably don't want to change I2C frequency while a transfer is in
progress. The current implementation grabs a spinlock, but that only
protected the writes to IICCON when starting a message, it didn't protect
against clock changes in the middle of a transaction.
Note: The i2c-core already grabs the adapter lock before calling
s3c24xx_i2c_doxfer(), which ensures that only one caller is issuing a
xfer at a time. This means it is not necessary to disable interrupts
(spin_lock_irqsave) when changing frequencies, since there won't be
any i2c interrupts if there is no on-going xfer.
Lastly, i2c_lock_adapter() may cause the cpufreq_transition to sleep if
if a xfer is in progress, but this is ok since cpufreq notifiers are
called in a kernel thread, and there are already cases where it could
sleep, such as when using i2c to update the output of a voltage
regulator.
Note: the cpufreq part of this change has no functional affect on
exynos, where the i2c clock is independent of the cpufreq.
But, there is a slight perfomance boost since we no longer need to
lock/unlock an additional spinlock.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch adds support for pin configuration using pinctrl subsystem
to the i2c-s3c2410 driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
A small code saving and less error handling to worry about.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Use the PM_SLEEP ifdef for system suspend and resume. This is partly
in preparation for adding runtime operations and partly because a user
may in theory choose to enable runtime suspend but not system suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Allow the i2c-mux-gpio to be used by a device tree enabled device. The
bindings are inspired by the one found in the i2c-mux-pinctrl driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
[wsa: fixed some whitespace]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Ensure that any of preceding register write operations to the I2C
hardware block reached the module, and the write data is reflected
in the registers, before leaving the interrupt handler.
Otherwise, we'll suffer from spurious WAIT interrupts that lead to
'Transfer request timed out' message, and the transaction failed.
Reported-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
On newer SH-/R-Mobile SoCs, a clock supply to the I2C hardware block,
which is used to generate the SCL clock output, is getting faster than
before, while on the other hand, the SCL clock control registers, ICCH
and ICCL, stay unchanged in 9-bit-wide (8+1).
On such silicons, the internal SCL clock counter gets incremented every
2 clocks of the operating clock.
This patch makes it configurable through platform data.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
ICCH/ICCL values is supposed to be calculated/optimized to strictly meet
the timing specs required by the I2C standard. The resulting I2C bus
speed does not matter at all, if it's less than 100 or 400 kHz.
With this change, sh_mobile_i2c_icch() is virtually identical to
sh_mobile_i2c_iccl(), but they're providing good descriptions of
SH-/R-Mobile I2C hardware spec, and I'd leave them as separated.
Also fix a typo in the comment, print icch/iccl values at probe, etc.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
[wsa: squashed two patches for bisectability]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently SCL clock parameters (ICCH/ICCL) are calculated in
activate_ch(), which gets called every time sh_mobile_i2c_xfer() is
processed, while each I2C bus speed is system-defined and in general
those parameters do not have to be updated over I2C transactions.
The only reason I could see having it transaction-time is to adjust
ICCH/ICCL values according to the operating frequency of the I2C
hardware block, in the face of DFS (Dynamic Frequency Scaling).
However, this won't be necessary.
The operating frequency of the I2C hardware block can change _even_
in the middle of I2C transactions. There is no way to prevent it
from happening, and I2C hardware block can work with such dynamic
frequency change, of course.
Another is that ICCH/ICCL clock parameters optimized for the faster
operating frequency, can also be applied to the slower operating
frequency, as long as slave devices work. However, the converse is
not true. It would violate SCL timing specs of the I2C standard.
What we can do now is to calculate the ICCH/ICCL clock parameters
according to the fastest operating clock of the I2C hardware block.
And if that's the case, that calculation should be done just once
at driver-module-init time.
This patch moves ICCH/ICCL calculating part from activate_ch() into
sh_mobile_i2c_init(), and call it from sh_mobile_i2c_probe().
Note that sh_mobile_i2c_init() just prepares clock parameters using
the clock rate and platform data provided, but does _not_ make any
hardware I/O accesses. We don't have to care about run-time PM
maintenance here.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Filenames of devictree binding documentation seems to be arbitrary and
for me it is unneeded hazzle to find the corresponding documentation for
a specific driver.
Naming the description the same as the driver is a lot easier and makes
sense to me since the driver defines the binding it understands.
Also, remove a reference in one source to the binding documentation, since path
information easily gets stale.
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently after the reset the sysc is written with hardcoded values.
The patch reads the sysc register and writes back the same value
after reset.
- Some unnecessary rev checks can be optimised.
- Also due to whatever reason the hwmod flags are changed
we will not reset the values.
- In some of the cases the minor values of the 2430 register
is different(0x37) in that case the autoidle setting may be missed.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently the restore is done based on the flag
OMAP_I2C_FLAG_RESET_REGS_POSTIDLE.
This helps the following
- The driver is always capable of restoring regardless
of the off mode support being there or not.
- While testing omap2430 it is found that in case of certain
error paths (timeout) a reset is done. However the restore
never happens as it is dependent on the POSTIDLE flag.
The other option would be to call a restore in the reset
case. As there are only a few registers to be restored
the penalty in the idle case should not be much.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Implement reset as a separate function.
This will enable us to make sure that we don't do the
calculation again on every transfer.
Also at probe the reset is not added as the hwmod is doing that
for us.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
re-factor omap_i2c_init() so that we can re-use it for resume.
While at it also remove the bufstate variable as we write it
in omap_i2c_resize_fifo for every transfer.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The commit [i2c: omap: use revision check for OMAP_I2C_FLAG_APPLY_ERRATA_I207]
uses the revision id instead of the flag. So the flag can be safely removed.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The dtrev is used only for the comments. Remove the same and use
the scheme instead to know if it is version2.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The errata i207 is enabled for 2430 and 3xxx. Use the revision check
to enable the erratum instead.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The revision register on OMAP4 is a 16-bit lo and a 16-bit
hi. Currently the driver reads only the lower 8-bits.
Fix the same by preventing the truncating of the rev register
for OMAP4.
Also use the scheme bit ie bit-14 of the hi register to know if it
is OMAP_I2C_IP_VERSION_2.
On platforms previous to OMAP4 the offset 0x04 is IE register whose
bit-14 reset value is 0, the code uses the same to its advantage.
Also since the omap_i2c_read_reg uses reg_map_ip_* a raw_readw is done
to fetch the revision register.
The dev->regs is populated after reading the rev_hi. A NULL check
has been added in the resume handler to prevent the access before
the setting of the regs.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Some GPIO expanders need some early pin control muxing. Due to
legacy boards sometimes the driver uses subsys_initcall instead of
module_init. This patch takes advantage of defer probe feature
and pin control in order to wait until pin control probing before
GPIO driver probing. It has been tested on OMAP5 board with TCA6424
driver.
Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Acked-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
if we allow compiler reorder our writes, we could
fall into a situation where dev->buf_len is reset
for no apparent reason.
This bug was found with a simple script which would
transfer data to an i2c client from 1 to 1024 bytes
(a simple for loop), when we got to transfer sizes
bigger than the fifo size, dev->buf_len was reset
to zero before we had an oportunity to handle XDR
Interrupt. Because dev->buf_len was zero, we entered
omap_i2c_transmit_data() to transfer zero bytes,
which would mean we would just silently exit
omap_i2c_transmit_data() without actually writing
anything to DATA register. That would cause XDR
IRQ to trigger forever and we would never transfer
the remaining bytes.
After adding the memory barrier, we also drop resetting
dev->buf_len to zero in omap_i2c_xfer_msg() because
both omap_i2c_transmit_data() and omap_i2c_receive_data()
will act until dev->buf_len reaches zero, rendering the
other write in omap_i2c_xfer_msg() redundant.
This patch has been tested with pandaboard for a few
iterations of the script mentioned above.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
if we allow compiler reorder our writes, we could
fall into a situation where dev->buf_len is reset
for no apparent reason.
This bug was found with a simple script which would
transfer data to an i2c client from 1 to 1024 bytes
(a simple for loop), when we got to transfer sizes
bigger than the fifo size, dev->buf_len was reset
to zero before we had an oportunity to handle XDR
Interrupt. Because dev->buf_len was zero, we entered
omap_i2c_transmit_data() to transfer zero bytes,
which would mean we would just silently exit
omap_i2c_transmit_data() without actually writing
anything to DATA register. That would cause XDR
IRQ to trigger forever and we would never transfer
the remaining bytes.
After adding the memory barrier, we also drop resetting
dev->buf_len to zero in omap_i2c_xfer_msg() because
both omap_i2c_transmit_data() and omap_i2c_receive_data()
will act until dev->buf_len reaches zero, rendering the
other write in omap_i2c_xfer_msg() redundant.
This patch has been tested with pandaboard for a few
iterations of the script mentioned above.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The driver claims to support SMBus quick command but it was not the
case. This patch fixes this issue. Without it, i2cdetect finds imaginary
devices. And with some IP versions, trying to send 0 byte can cause
issue when writing data to an EEPROM.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[wsa: improved the commit message]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The driver claims to support SMBus quick command but it was not the
case. This patch fixes this issue. Without it, i2cdetect finds imaginary
devices. And with some IP versions, trying to send 0 byte can cause
issue when writing data to an EEPROM.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[wsa: improved the commit message]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
When having multiple i2c-gpio nodes, the name for each is same.
So add the patch to fix it.
The adap->name printing information was added by myself
without this patch the log information is as following
---<8---
adap->name = i2c-gpio-1
i2c-gpio i2c.2: using pins 30 (SDA) and 31 (SCL)
adap->name = i2c-gpio-1
i2c-gpio i2c.3: using pins 64 (SDA) and 65 (SCL)
--->8---
with this patch, the log information is as following
---<8---
adap->name = i2c.2
i2c-gpio i2c.2: using pins 30 (SDA) and 31 (SCL)
adap->name = i2c.3
i2c-gpio i2c.3: using pins 64 (SDA) and 65 (SCL)
--->8---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
[wsa: minor fixes to the commit mesage]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
When allocating the memory for i2c busses, the code checked the wrong
variable and thus never detected if there was a memory error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Replacing the devm_request_mem_region() and devm_ioremap_nocache() calls
by a single call to devm_request_and_ioremap() simplifies the code.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Give the driver struct a name according to the 'standard' to fix:
WARNING: vmlinux.o(.data+0x11798): Section mismatch in reference from the variable rcar_i2c_drv to the function .devinit.text:rcar_i2c_probe()
...
WARNING: vmlinux.o(.data+0x1179c): Section mismatch in reference from the variable rcar_i2c_drv to the function .devexit.text:rcar_i2c_remove()
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pull i2c embedded fixes from Wolfram Sang:
"Two patches are usual stuff.
The bigger patch is needed to correct a wrong decision made in this
merge window. We hoped to get the PIOQUEUE mode in the mxs driver
working with DMA, but it turned out to be too broken (leading to data
loss), so we now think it is best to remove it entirely and work only
with DMA now. The patch should be in 3.7. IMO, so users never get
the chance to use both modes in parallel."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: tegra: set irq name as device name
i2c-nomadik: Fixup clock handling
i2c: mxs: remove broken PIOQUEUE support
When watching the irqs name of tegra i2c, all instances
irq name shows as tegra_i2c.
Passing the device name properly to have the irq names with
instance like tegra-i2c.0, tegra-i2c.1 etc.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make sure to clk_prepare as well as clk_enable.
Signed-off-by: Philippe Begnic <philippe.begnic@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This I2C master can do DMA and PIOQUEUE (PIO with FIFO). Originally,
only PIOQUEUE was supported and it had issues, then DMA support was added
this cycle. The original intention was to keep PIOQUEUE since it has
less overhead what is nice for small transfers. However, runtime
switching between PIOQEUE and DMA depending on the transfer size never
worked despite a lot of trying. Since PIOQUEUE mode itself was flaky
(polling at places where interrupts failed to work) and the
implementation also imposed a size limit for transfers, it is best to
remove the support, so users don't fall over its limitations. It also
makes the driver a lot cleaner and more robust. If somebody really wants
less overhead, plain PIO mode could still be implemented with the
addidtional advantage that this mode is also available on MX23, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Arbitrarily selecting GPIOLIB causes trouble on some architectures,
so don't do that. Instead, just make the optional multiplexing code
depend on CONFIG_I2C_MUX_GPIO instead of CONFIG_I2C_MUX for now. We
can revisit if the i2c-i801 driver ever supports other multiplexing
flavors.
Also make that optional code depend on DMI, as it won't do anything
without that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Move the i2c-stub driver to drivers/i2c, to match the Kconfig entry.
This is less confusing that way.
I also fixed all checkpatch warnings and errors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Huewe <peterhuewe@gmx.de>
This is some amount of work left/forgot from device tree conversion.
Instead of checking cpu_is_xxx to determine the controller type, the
driver should use platform_device_id, which should match the device
tree compatible string.
The patch changes the driver to use platform_device_id rather than
cpu_is_xxx to determine the controller type/version. It also updates
the platform code and device tree source accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
Pull i2c-embedded changes from Wolfram Sang:
"The changes for i2c-embedded include:
- massive rework of the omap driver
- massive rework of the at91 driver. In fact, the old driver gets
removed; I am okay with this approach since the old driver was
depending on BROKEN and its limitations made it practically
unusable, so people used bitbanging instead. But even if there are
users, there is no platform_data or module parameter which would
need to be converted. It is just another driver doing I2C
transfers, just way better. Modifications of arch/arm/at91 related
files have proper acks from the maintainer.
- new driver for R-Car I2C
- devicetree and generic_clock conversions and fixes
- usual driver fixes and changes.
The rework patches have come a long way and lots of people have been
involved in creating/testing them. Most patches have been in
linux-next at least since 3.6-rc5. A few have been added in the last
week, I have to admit.
An unexpected (but welcome :)) peak in private life is the cause for
that. The "late" patches shouldn't cause any merge conflicts and I
will have a special eye on them during the stabilization phase. This
is an exception and I want to have the patches in place properly in
time again for the next kernels."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (44 commits)
MXS: Implement DMA support into mxs-i2c
i2c: add Renesas R-Car I2C driver
i2c: s3c2410: use clk_prepare_enable and clk_disable_unprepare
ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints
i2c: nomadik: Add Device Tree support to the Nomadik I2C driver
i2c: algo: pca: Fix chip reset function for PCA9665
i2c: mpc: Wait for STOP to hit the bus
i2c: davinci: preparation for switch to common clock framework
omap-i2c: fix incorrect log message when using a device tree
i2c: omap: sanitize exit path
i2c: omap: switch over to autosuspend API
i2c: omap: remove unnecessary pm_runtime_suspended check
i2c: omap: switch to threaded IRQ support
i2c: omap: remove redundant status read
i2c: omap: get rid of the "complete" label
i2c: omap: resize fifos before each message
i2c: omap: simplify IRQ exit path
i2c: omap: always return IRQ_HANDLED
i2c: omap: simplify errata check
i2c: omap: bus: add a receiver flag
...
This patch implements DMA support into mxs-i2c. DMA transfers are now enabled
via DT. The DMA operation is enabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
[wsa: rebased to 3.6-rc7]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQX7MuAAoJEHm+PkMAQRiG0h0IAJURkrMCAQUxA+Ik66ReH89s
LQcVd0U9uL4UUOi7f5WR64Vf9Cfu6VVGX9ZKSvjpNskvlQaUQPMIt4pMe6g4X4dI
u0bApEy4XZz3nGabUAghIU8jJ8cDmhCG6kPpSiS7pi7KHc0yIa4WFtJRrIpGaIWT
xuK38YOiOHcSDRlLyWZzainMncQp/ixJdxnqVMTonkVLk0q0b84XzOr4/qlLE5lU
i+TsK3PRKdQXgvZ4CebL+srPBwWX1dmgP3VkeBloQbSSenSeELICbFWavn2ml+sF
GXi4dO93oNquL/Oy5SwI666T4uNcrRPaS+5X+xSZgBW/y2aQVJVJuNZg6ZP/uWk=
=0v2l
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc7' into i2c-embedded/for-next
Linux 3.6-rc7
Needed to get updates from i2c-embedded/for-current into i2c-embedded/for-next
R-Car I2C is similar with SH7760 I2C.
But the SH7760 I2C driver had many workaround operations, since H/W had bugs.
Thus, it was pointless to keep compatible between SH7760 and R-Car I2C drivers.
This patch creates new Renesas R-Car I2C driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Pul ACPI & Power Management updates from Len Brown:
- acpidump utility added
- intel_idle driver now supports IVB Xeon
- turbostat utility can now count SMIs
- ACPI can now bind to USB3 hubs
- misc fixes
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (49 commits)
ACPI: Add new sysfs interface to export device description
ACPI: Harden acpi_table_parse_entries() against BIOS bug
tools/power/turbostat: add option to count SMIs, re-name some options
tools/power turbostat: add [-d MSR#][-D MSR#] options to print counter deltas
intel_idle: enable IVB Xeon support
tools/power turbostat: add [-m MSR#] option
tools/power turbostat: make -M output pretty
tools/power turbostat: print more turbo-limit information
tools/power turbostat: delete unused line
tools/power turbostat: run on IVB Xeon
tools/power/acpi/acpidump: create acpidump(8), local make install targets
tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
ACPI: run _OSC after ACPI_FULL_INITIALIZATION
tools/power/acpi/acpidump: create acpidump(8), local make install targets
tools/power/acpi/acpidump: version 20101221 - find dynamic tables in sysfs
tools/power/acpi/acpidump: version 20071116
tools/power/acpi/acpidump: version 20070714
tools/power/acpi/acpidump: version 20060606
tools/power/acpi/acpidump: version 20051111
xo15-ebook: convert to module_acpi_driver()
...
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Convert the driver from the outdated omap_pm_set_max_mpu_wakeup_lat
API to the new PM QoS API.
Since the constraint is on the MPU subsystem, use the PM_QOS_CPU_DMA_LATENCY
class of PM QoS. The resulting MPU constraints are used by cpuidle to
decide the next power state of the MPU subsystem.
The I2C device latency timing is derived from the FIFO size and the
clock speed and so is applicable to all OMAP SoCs.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Here we apply the bindings required for successful Device Tree
probing of the i2c-nomadik driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The parameter passed to pca9665_reset is adap->data (which is bus driver
specific), not i2c_algp_pca_data *adap. pca9665_reset expects it to be
i2c_algp_pca_data *adap. All other wrappers from the algo call back to
the bus driver, which knows to handle its custom data. Only pca9665_reset
resides inside the algorithm code and does not know how to handle a custom
data structure. This can result in a kernel crash.
Fix by re-factoring pca_reset() from a macro to a function handling chip
specific code, and only call adap->reset_chip() if the chip is not PCA9665.
Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Now that i2c-mux-gpio is able to find the GPIO chip by itself, we can
delegate this task. The great thing here is that i2c-mux-gpio can
defer device probing until the gpio chip is available, so we no longer
depend on the module loading order.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The code instantiating an i2c-mux-gpio platform device doesn't
necessarily know in advance the GPIO pin numbers it wants to use. If
pins are on a GPIO device which gets its base GPIO number assigned
dynamically at run-time, the values can't be hard-coded.
In that case, let the caller tell i2c-mux-gpio the name of the GPIO
chip and the (relative) GPIO pin numbers to use. At probe time, the
i2c-mux-gpio driver will look for the chip and apply the proper offset
to turn relative GPIO pin numbers to absolute GPIO pin numbers.
The same could be (and was so far) done on the caller's end, however
doing it in i2c-mux-gpio has two benefits:
* It avoids duplicating the code on every caller's side (about 30
lines of code.)
* It allows for deferred probing for the muxed part of the I2C bus
only. If finding the GPIO chip is the caller's responsibility, then
deferred probing (if the GPIO chip isn't there yet) will not only
affect the mux and the I2C bus segments behind it, but also the I2C
bus trunk.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Use the devm_kzalloc managed function to stripdown the error and remove
code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for SMBus multiplexing on Asus Z8 motherboard series. On
these boards, the memory slots are behind a GPIO-controlled I2C
multiplexer. Models with 6 or 12 memory slots have 2 segments behind
the multiplexer, while models with 18 memory slots have 3 such
segments.
On these boards, only the memory slots are behind the multiplexer,
so it is possible to keep the autodetection mechanism.
The code is generic enough so it could work on other boards as long as
the multiplexer is controlled by GPIO pins. For other forms of
multiplexing (for example using an I2C device) additional code will be
needed.
Thanks to Asus for providing a board to develop and test this feature,
as well as all the technical information required.
At the moment, the GPIO driver must be loaded before the i2c-i801
driver, but I hope to solve this soon, using deferred probing on
the i2c-mux-gpio side.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The SMBus controller in the VIA VX900 appears to be compatible with
the VIA VX855, so just add the device ID.
This closes kernel bug #43096.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_dw_xfer_msg is only called internally so it can be static. It
original was, before the driver split. No idea why it was changed at
that time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Replace printks with pr_<level>s, add pr_fmt()s to replace NAMEs
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the global dependency of the I2C subsystem on HAS_IOMEM and
move the dependency to the i2c/busses submenu, with an exception for
i2c-stub.
The generic I2C part does not need to have HAS_IOMEM set and thus now
becomes available in UML, so the I2C subsystem can now be used, e.g.
by the i2c-stub driver, for development of I2C device drivers.
[JD: Some adjustments.]
[Heiko Carstens: Keep I2C disabled on S390.]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Converting kzalloc to devm_kzalloc simplifies the code and ensures that the
result, alert, is freed after the irq allocated by the subsequent
devm_request_irq. This in turn ensures that when an interrupt can be
triggered, the alert structure is still available.
The problem of a free after a devm_request_irq was found using the
following semantic match (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2,x,a,b,c,d;
identifier free;
position p1,p2;
@@
devm_request_irq@p1(e1,e2,...,x)
... when any
when != e2 = a
when != x = b
if (...) {
... when != e2 = c
when != x = d
free@p2(...,x,...);
...
return ...;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let I2C bus segments behind multiplexers have a class. This allows for
device auto-detection on these segments. As long as parent segments
don't share the same class, it should be fine.
I implemented support in drivers i2c-mux-gpio and i2c-mux-pca954x. I
left i2c-mux-pca9541 and i2c-mux-pinctrl alone for the moment as I
don't know if this feature makes sense for the use cases of these
drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Cc: Rodolfo Giometti <giometti@linux.it>
To avoid name conflicts:
drivers/video/riva/fbdev.c:281:9: sparse: preprocessor token MAX_LEVEL redefined
While at it, also make the other names more consistent and add
parentheses.
[akpm@linux-foundation.org: repair fallout]
[sfr@canb.auug.org.au: IB/mlx4: fix for MAX_ID_MASK to MAX_IDR_MASK name change]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: walter harms <wharms@bfs.de>
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck7M
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the samsung include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: linux-samsung-soc@vger.kernel.org
Pull i2c embedded fixes from Wolfram Sang:
"The last bunch of (typical) i2c-embedded driver fixes for 3.6.
Also update the MAINTAINERS file to point to my tree since people keep
asking where to find their patches."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: algo: pca: Fix mode selection for PCA9665
MAINTAINERS: fix tree for current i2c-embedded development
i2c: mxs: correctly setup speed for non devicetree
i2c: pnx: Fix read transactions of >= 2 bytes
i2c: pnx: Fix bit definitions
mpc_i2c_stop() only initiates STOP but does not wait for it to
hit the I2C bus. This is a problem when using I2C devices which
uses fairly long clock stretching just before STOP if you also
have an i2c-mux which may switch to another bus before STOP has
been processed.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The code currently always selects turbo mode for PCA9665, no matter which
clock frequency is configured. This is because it compares the clock frequency
against constants reflecting (boundary / 100). Compare against real boundary
frequencies to fix the problem.
Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
As a first step towards migrating davinci platforms to use common clock
framework, replace all instances of clk_enable() with clk_prepare_enable()
and clk_disable() with clk_disable_unprepare(). Until the platform is
switched to use the CONFIG_HAVE_CLK_PREPARE Kconfig variable, this just
adds a might_sleep() call and would work without any issues.
This will make it easy later to switch to common clk based implementation
of clk driver from DaVinci specific driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the w90x900 include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Wolfram Sang