Currently the routines wait for the various bits w/o an assumption that
bits may never get set. When timeouts happen I see that these bits never
get set and so the routines hang the kernel.
With this patch we'll wait the graceful stop for 100 ms, and then will
simply exit. There is nothing* we can do about that, but it's OK since
we'll do full reset later.
* Well, actually, there is also not-graceful variant for the TX stop,
but specs says that we never should use it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize the lightly loaded case, by only synchronizing discards stats
when qlen > 10 indicate potential for drops.
Notice Robert Olsson might disagree with this patch.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discard packet counter debug statements that can be turned on
at runtime by users to assist debugging of the driver code.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implementing discard counters for the NIU driver turned out to be more
complicated than first assumed.
The discard counters for the NIU neptune chip are only 16-bit (even
though this is a 64-bit chip). These 16-bit counters can overflow
quickly, especially considering this is a 10Gbit/s ethernet card.
The overflow indication bit is, unfortunatly, not usable as the
counter value does not wrap, but remains at max value 0xFFFF.
Resulting in lost counts until the counter is reset.
The read and reset scheme also poses a problem. Both in theory and in
practice counters can be lost in between reading nr64() and clearing
the counter nw64(). For this reason, the number of counter clearings
nw64() is limited/reduced. On the fast-path the counters are only
syncronized once it exceeds 0x7FFF. When read by userspace, its
syncronized fully.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
A major source of overhead in the enc28j60 driver is the SPI transfers. Each
SPI transfer entails two kernel thread context switches. One major source of
SPI transfers is the enc28j60_set_bank() functions which runs before every
register access. This patch reduces the number of SPI transfers that
enc28j60_set_bank() performs in two ways:
1. removes unnecessary bank switch for the registers that are present in all
banks
2. when switching from banks 0 or 3 to banks 1 or 2 (i.e. only one bit
changes) enc28j60_set_bank() does only one SPI transfer instead of two
According to my tests these changes reduce the number of SPI transfers in
about 25%.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
| commit 3d29b0c33d
| Author: John W. Linville <linville@tuxdriver.com>
| Date: Fri Oct 31 14:13:12 2008 -0400
|
| netdevice zd1201: Convert directly reference of netdev->priv to netdev_priv()
|
| We have some reasons to kill netdev->priv:
| 1. netdev->priv is equal to netdev_priv().
| 2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
| netdev_priv() is more flexible than netdev->priv.
| But we cann't kill netdev->priv, because so many drivers reference to it
| directly.
|
| OK, becasue Dave S. Miller said, "every direct netdev->priv usage is a bug",
| and I want to kill netdev->priv later, I decided to convert all the direct
| reference of netdev->priv first.
|
| (Original patch posted by Wang Chen <wangchen@cn.fujitsu.com> w/ above
| changelog but using dev->ml_priv. That doesn't seem appropriate
| to me for this driver, so I've revamped it to use netdev_priv()
| instead. -- JWL)
This commit changed the allocation of netdev, but didn't change
the free method of it.
This causes "zd" be used after the memory, which is pointed by "zd", being
freed by free_netdev().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I also removed some of the unneeded braces in the if condition to
improve readability and a little bit of reformatting.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are all defined before used, it's therefore ok to remove
them.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove the pointless comment at the top.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It helps in maintaining the various partner information values from
the LACPDU. It also removes the pointless comment at the top.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It generally helps to handle those values in various places, using it
might make the code more readable and gives room for other improvements.
The IEEE standard talks about them as "parameter values".
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code was just a funny way of assigning both values (they
are both of type u8).
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gfar_poll would declare polling done once the rx queue was empty,
but the tx queue could still have packets left.
Stolen mostly from the e1000 driver.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No clean up function is executed in the interrupt context by this patch.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interface name (ex. eth0) is used as the prefix for the interrupt name,
with _rx, _tx, and _er appended to distinguish multiple interrupts on
the same interface.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scatter Gather support in gianfar driver to handle fragmented frames on
the transmit side.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch which fixed gianfar so it drops packets when it runs out
of memory left in the code which frees the skb when it drops packets.
Change the code so that we only free the skb if the new skb was successfully
created.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the Nokia vendor-specific communication device class
function to exchange Phonet messages over USB. This function is already
found in the "PC suite" USB profile of (non-Linux) Nokia handsets.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use idr technique instead of own implemented cardmaps.
It saves us a number of lines and gives an ability
to use library functions.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are now defined in linux/mii.h and the bnx2x driver
defines different values which are shared with hardware
data structures.
So add a "BNX2X_" prefix to these macro names.
Based upon a report from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
And fix the 5716S pci_device_id entry to point to the proper string.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change MSI-X vector names to "ethx-%d".
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_setup_forced hasn't actually reset the PHY for a long time,
but a comment to that effect remained in the code, so code continued
to act as if it *had* reset the PHY, and called the necessary fixup
functions to respond to a PHY reset. With no reset, those functions
are no longer needed, so we remove them.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever we want to update the status field in a BD, we usually want to
update the length field, too. By combining them into one 32-bit field, we
reduce the number of stores to memory shared with the controller, and we
eliminate the need for order-enforcement, as the length and "READY" bit are
now updated atomically at the same time.
Signed-off-by: Dai Haruki <Dai.Haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is based strongly on code from Dai Haruki <Dai.Haruki@freescale.com>.
The gianfar Buffer Descriptors are arranged in a circular array, the end of
which is denoted by setting the "WRAP" bit in the descriptor. However, the
software knows the end of the ring because it knows how many descriptors are
there. Rather than check each descriptor for whether the WRAP bit is set,
use pointer math to determine where the next BD is. This is also useful for
when we want to look at BDs other than the very next one (for Scatter-Gather).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Also, use cacheable_memzero instead of memset for performance reasons.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The eTSEC can prepend up to 32 bytes to a received frame, usually for the
purpose of aligning the IP address to a word boundary, so this turns it on.
While we're in there, make the handling of the pre-frame bytes (padding and
Frame Control Block) cleaner.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize the VLAN checking logic as well.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some bugs in the ethtool configuration functions:
* gfar_clean_rx_ring should not be called with interrupts disabled.
* Update last transmission time to avoid tx timeout.
* Delete redundant NETIF_F_IP_CSUM check in gfar_start_xmit
* Use netif_tx_lock_bh when reconfiguring the tx csum
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the interrupt coalescing values in the form in which they will be
written to the interrupt coalescing registers. This puts a little overhead
into the ethtool configuration, and takes it out of the interrupt handler
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Does the same for the accompanying MDIO driver, and then modifies the TBI
configuration method. The old way used fields in einfo, which no longer
exists. The new way is to create an MDIO device-tree node for each instance
of gianfar, and create a tbi-handle property to associate ethernet controllers
with the TBI PHYs they are connected to.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gfar_halt does everything we want to do there, including disabling
TX/RX. It also doesn't unnecessarily enable DMA if it's already
stopped.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The big rx/tx buffer support is broken and unlikely to be very useful
as such. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix pci unmapping problem introduced by commit id
8953f12827 "tlan: Fix small (< 64 bytes)
datagram transmissions".
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
These 4 drivers have identical full duplex flow control resolution
functions. This patch changes them all to use one common function.
The function in question decides whether a device should enable TX and
RX flow control in a standard way (IEEE 802.3-2005 table 28B-3), so this
should also be useful for other drivers.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flags used within drivers for indicating tx and rx flow control are
defined in 4 drivers (and probably more), move these constants to mii.h.
The 3 SMSC drivers use the same constants (FLOW_CTRL_TX), but TG3 uses
TG3_FLOW_CTRL_TX, so this patch also renames the constants within TG3.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NIC driver can work with mutliple versions of the FW.
Let the driver load when the embedded FW does not match,
and the FW update mechanism failed.
The iWARP module will make its own loading decision.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enc28j60 driver reads incoming packets in the process (workqueue) context,
not in a tasklet or the interrupt context. Thus, we should use netif_rx_ni()
to deliver those packets to the networking layer, instead of netif_rx(). This
way incoming packets don't wait in the incoming queue for the next IRQ to be
serviced.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TLAN chip does not support tranmissions smaller than 64
bytes. Smaller transfers need to be padded up to that size. This was
broken by commit id 41873e9aff ("tlan:
get rid of padding buffer").
<URL:http://bugzilla.kernel.org/show_bug.cgi?id=11754>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pppol2tp driver has had broken UDP checksum code for a long
time. This patch fixes it. If UDP checksums are enabled in the
tunnel's UDP socket, the L2TP driver now properly validates the
checksum on receive and fills in the checksum on transmit. If the
network device has hardware checksum support and is enabled, it is
used instead of generating/checking the checksum in software.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this sparse warnings by making the functions static:
drivers/isdn/hardware/eicon/di.c:356:6: warning: symbol 'isdn_rc' was not declared. Should it be static?
drivers/isdn/hardware/eicon/di.c:558:6: warning: symbol 'isdn_ind' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:595:6: warning: symbol 'api_parse' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:634:6: warning: symbol 'api_save_msg' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:666:6: warning: symbol 'api_load_msg' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:3417:6: warning: symbol 'manufacturer_req' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:3745:6: warning: symbol 'manufacturer_res' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:4077:6: warning: symbol 'control_rc' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:4743:6: warning: symbol 'data_rc' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:4779:6: warning: symbol 'data_ack' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:4805:6: warning: symbol 'sig_ind' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:6173:6: warning: symbol 'SendInfo' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:6349:6: warning: symbol 'SendMultiIE' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:6468:6: warning: symbol 'nl_ind' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7250:6: warning: symbol 'get_plci' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7409:6: warning: symbol 'add_d' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7427:6: warning: symbol 'add_ai' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7448:6: warning: symbol 'add_b1' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:7912:6: warning: symbol 'add_b23' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8709:6: warning: symbol 'nl_req_ncci' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8731:6: warning: symbol 'send_req' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8866:6: warning: symbol 'listen_check' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8909:6: warning: symbol 'IndParse' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:8994:6: warning: symbol 'ie_compare' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9003:6: warning: symbol 'find_cip' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9071:6: warning: symbol 'SetVoiceChannel' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9089:6: warning: symbol 'VoiceChannelOff' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9102:6: warning: symbol 'AdvCodecSupport' was not declared. Should it be static?
drivers/isdn/hardware/eicon/message.c:9198:6: warning: symbol 'CodecIdCheck' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Vorontsov