Later versions of this controller also allow 4k pagesize,
so use mtd->writesize instead of a flag.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The main/spare areas are on different addresses on later versions
of the controller, so make them configurable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The NAND controller has some limitations how to access the
internal buffers. It only allows 32 bit accesses. The driver
used to work around this by having special alignment aware
copy routines.
We now copy the whole page to a buffer in memory and let the
access functions use this buffer. This simplifies the driver.
A bonnie++ test showed that this has no negative performance
impact on the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This factors the address cycle to a seperate function. This
becomes useful in a later patch where we can simplify the
command processing by making use of this function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The oob layout was initialized several times. Instead, use
a smallpage layout by default and switch to a largepage
afterwards if necessary.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The original Freescale driver used to have eccoob descriptions like
this:
static struct nand_ecclayout nand_hw_eccoob_8 = {
.eccbytes = 5,
.eccpos = {6, 7, 8, 9, 10},
.oobfree = {{0, 5}, {11, 5}}
};
static struct nand_ecclayout nand_hw_eccoob_16 = {
.eccbytes = 5,
.eccpos = {6, 7, 8, 9, 10},
.oobfree = {{0, 6}, {12, 4}}
};
The former was used for 8bit flashes and the latter for 16bit flashes.
They honored the fact that the bad block marker on 8bit flashes is on byte 5
while on 16bit flashes it is on byte 11.
In the Kernel driver this was copied wrong and we ended up with two identical
descriptions.
Change it so that we have only one description which leaves byte 5 and byte
11 unspecified so that it won't be used by others.
Also, rename the descriptions to nand_hw_eccoob_smallpage and
nand_hw_eccoob_largepage so that it can't be confused with Nand chip bus
widths (what actually happened in this driver)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The commit d79c326 ("gpio-addr-flash: new driver for GPIO assisted
flash addressing") removed two lines from the Makefile by accident.
Though I'm not sure how this accident happened, this patch reverts the
removal.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert PCMCIA drivers to use the dynamic debug infrastructure, instead of
requiring manual settings of PCMCIA_DEBUG.
Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.
CC: linux-mtd@lists.infradead.org
CC: linux-usb@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* git://git.infradead.org/users/dwmw2/mtd-2.6.32:
mtd/maps: gpio-addr-flash: depend on GPIO arch support
mtd/maps: gpio-addr-flash: pull in linux/ headers rather than asm/
mtd: nand: fix htmldocs warnings
Commit 4b56ffcace ("mtd: Fix kernel NULL
pointer dereference in physmap.c") introduced a couple of bugs.
It neglected to run the loop of map_destroy() calls in
physmap_flash_remove(), if !info->cmtd, which would happen if that
function was called to clean up errors during probe.
It also failed to compile if CONFIG_MTD_PARTITIONS was not defined.
Reported-By: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 71b7d0d90d.
The problem which that commit attempted to fix was a bootloader issue,
which had been misunderstood. The 'fix' causes lots of false bad blocks
for existing users with sane firmware.
Thanks to Mathieu Berland for diagnosing the problem coherently.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In register_mtd_blktrans(), the symbol 'ret' is already declared
as an int at the start of the function. The inner loop declaration
is unnecessary. Quiets the following sparse warning:
warning: symbol 'ret' shadows an earlier one
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
result is unsigned, the wrong check was used.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Commit 32bc482028 did not fully fix
the backward compatibility issues. We still fail to properly handle
situations when the first PEB contains non-zero image sequence
number, but one of the following PEBs contains zero image sequence
number. For example, this may happen if we mount a new image with
an old kernel, and then try to mount it in the new kernel.
This patch should fix the issue.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
During the probe for physmap platform flash devices there are a
number error exit conditions that all do a goto err_out which
then calls physmap_flash_remove(). In that function one of the
cleanup steps is:
#ifdef CONFIG_MTD_CONCAT
if (info->cmtd != info->mtd[0])
mtd_concat_destroy(info->cmtd);
#endif
This test will succeed since info->cmtd == NULL and info->mtd[0] is
valid.
Fix this by exiting the remove function when info->cmtd == NULL.
Also, cleanup the #ifdef CONFIG_MTD_PARTITIONS stuff by using
mtd_has_partitions().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a request_mem_region() before doing the ioremap(). Also, use the
resource_size macro instead of doing the end - start + 1 calc by hand.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert the (broken) pcmciamtd driver to use the new CIS helpers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver seems to be obsolete and broken for a long time.
It depends on CONFIG_IPAQ_HANDHELD that simply doesn't exists
anywhere in kernel. Also, it seems that none of machines it
claims to support have any use of it:
SA11xx-based iPAQs (h3100/h3600) use sa1100-flash
iPAQ h5000 uses physmap-flash
Jornada 720 uses sa1100-flash
Jornada 560 and iPAQ h1910 are not in mainline
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix a potential memory leak in mtd_dataflash driver.
The private data that is allocated when registering a DataFlash
device with the MTD subsystem is not released if an error occurs
when add_mtd_partitions() or add_mtd_device() is called. Fix this
by adding an error path. The memory is already released during a
remove.
Also, add a dev_set_drvdata(&spi->dev, NULL) before the kfree() so
that the spi device does not reference invalid data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- Remove unnecessary memset for bbt
All entries will be initialized at a few lines below
- Remove unnecessary initialization for mtd->erasesize
- Use write_whole_device()
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit f0b1e589 changed sa1100_mtd_probe from __init to __devinit,
but missed to correct sa1100_setup_mtd definition accordingly, which
causes following warning:
WARNING: vmlinux.o(.devinit.text+0xf4): Section mismatch in reference from
the function sa1100_mtd_probe() to the function .init.text:sa1100_setup_mtd()
The function __devinit sa1100_mtd_probe() references
a function __init sa1100_setup_mtd().
If sa1100_setup_mtd is only used by sa1100_mtd_probe then
annotate sa1100_setup_mtd with a matching annotation.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function mxcnd_remove is used only wrapped by __exit_p so define it
using __exit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Vladimir Barinov <vova.barinov@gmail.com>
Cc: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
This patch resolves all the prints present in onenand_base.c
Primarily, it replaces the hard-coded function names in the prints,
and makes use of __func__.
Signed-off-by: Amul Kumar Saha <amul.saha@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Correct typo to use mask_ale from platform data when set to non-zero.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
prepare_discard_fn() was being called in a place where memory allocation
was effectively impossible. This makes it inappropriate for all but
the most trivial translations of Linux's DISCARD operation to the block
command set. Additionally adding a payload there makes the ownership
of the bio backing unclear as it's now allocated by the device driver
and not the submitter as usual.
It is replaced with QUEUE_FLAG_DISCARD which is used to indicate whether
the queue supports discard operations or not. blkdev_issue_discard now
allocates a one-page, sector-length payload which is the right thing
for the common ATA and SCSI implementations.
The mtd implementation of prepare_discard_fn() is replaced with simply
checking for the request being a discard.
Largely based on a previous patch from Matthew Wilcox <matthew@wil.cx>
which did the prepare_discard_fn but not the different payload allocation
yet.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
drivers/mtd/maps/sa1100-flash.c: In function 'sa1100_probe_subdev':
drivers/mtd/maps/sa1100-flash.c:214: warning: format '%d' expects type 'int', but argument 3 has type 'uint64_t'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The SST SPI flashes is like Atmel SPI flashes in that the software
protection bits are set by default at power up, so clear them at init
time.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The driver requires gpio functionality, so make sure we depend on that in
the Kconfig menu.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now that there are linux/ versions of gpio.h and io.h, include those
rather than hitting the asm/ versions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (24 commits)
microblaze: Disable heartbeat/enable emaclite in defconfigs
microblaze: Support simpleImage.dts make target
microblaze: Fix _start symbol to physical address
microblaze: Use LOAD_OFFSET macro to get correct LMA for all sections
microblaze: Create the LOAD_OFFSET macro used to compute VMA vs LMA offsets
microblaze: Copy ppc asm-compat.h for clean handling of constants in asm and C
microblaze: Actually show KiB rather than pages in "Freeing initrd memory:"
microblaze: Support ptrace syscall tracing.
microblaze: Updated CPU version and FPGA family codes in PVR
microblaze: Generate correct signal and siginfo for integer div-by-zero
microblaze: Don't be noisy when userspace causes hardware exceptions
microblaze: Remove ipc.h file which points to non-existing asm-generic file
microblaze: Clear sticky FSR register after generating exception signals
microblaze: Ensure CPU usermode is set on new userspace processes
microblaze: Use correct kbuild variable KBUILD_CFLAGS
microblaze: Save and restore msr in hw exception
microblaze: Add architectural support for USB EHCI host controllers
microblaze: Implement include/asm/syscall.h.
microblaze: Improve checking mechanism for MSR instruction
microblaze: Add checking mechanism for MSR instruction
...
Fixed following htmldocs warnings:
DOCPROC Documentation/DocBook/mtdnand.xml
Warning(drivers/mtd/nand/nand_base.c:769): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:785): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:824): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:947): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:996): No description found for parameter 'page'
Warning(drivers/mtd/nand/nand_base.c:1040): No description found for parameter 'page'
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (58 commits)
mtd: jedec_probe: add PSD4256G6V id
mtd: OneNand support for Nomadik 8815 SoC (on NHK8815 board)
mtd: nand: driver for Nomadik 8815 SoC (on NHK8815 board)
m25p80: Add Spansion S25FL129P serial flashes
jffs2: Use SLAB_HWCACHE_ALIGN for jffs2_raw_{dirent,inode} slabs
mtd: sh_flctl: register sh_flctl using platform_driver_probe()
mtd: nand: txx9ndfmc: transfer 512 byte at a time if possible
mtd: nand: fix tmio_nand ecc correction
mtd: nand: add __nand_correct_data helper function
mtd: cfi_cmdset_0002: add 0xFF intolerance for M29W128G
mtd: inftl: fix fold chain block number
mtd: jedec: fix compilation problem with I28F640C3B definition
mtd: nand: fix ECC Correction bug for SMC ordering for NDFC driver
mtd: ofpart: Check availability of reg property instead of name property
driver/Makefile: Initialize "mtd" and "spi" before "net"
mtd: omap: adding DMA mode support in nand prefetch/post-write
mtd: omap: add support for nand prefetch-read and post-write
mtd: add nand support for w90p910 (v2)
mtd: maps: add mtd-ram support to physmap_of
mtd: pxa3xx_nand: add single-bit error corrections reporting
...
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: improve NOR flash erasure quirk
UBI: introduce flash dump helper
UBI: eliminate possible undefined behaviour
UBI: print a warning if too many PEBs are corrupted
UBI: amend NOR flash pre-erase quirk
UBI: print a message if ECH is corrupted and VIDH is ok
Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions to the following modules from drivers/mtd/
devices/m25p80.c
devices/slram.c
linux version 2.6.30
ftl.c
nand/cafe_nand.c
nand/cmx270_nand.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As with orion_nand in commit f33dabbe79
("register orion_nand using platform_driver_probe()"), avoid .init.text
problems by using platform_device_probe(). This isn't going to be
hotplugged anyway.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Using __nand_correct_data() helper function, this driver can read 512
byte (with 6 byte ECC) at a time. This results minor performance
improvement.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver may be reading 512 bytes at a times, but still calculates
256-byte sector ECC. So the nand_correct_data() is not appropriate
for this driver. Implement its ecc.correct function calling
__nand_correct_data() twice.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Split nand_correct_data() into two part, a pure calculation function
and a wrapper for mtd interface.
The tmio_nand driver can implement its ecc.correct function easily
using this __nand_correct_data helper.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The M29W128G Numonyx flash devices are intolerant to any 0xFF command:
in the Cfi_util.c the function cfi_qry_mode_off() (that resets the device
after the autoselect mode) must have a 0xF0 command after the 0xFF command.
This fix solves also the cause of the fixup_M29W128G_write_buffer() fix,
that can be removed now.
The following patch applies to 2.6.30 kernel.
Signed-off-by: Massimo Cirillo <maxcir@gmail.com>
Acked-by: Alexey Korolev <akorolev@infradead.org>
Cc: stable@kernel.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix ECC Correction bug where the byte offset location were double
fliped causing correction routine to toggle the wrong byte location
in the ECC segment. The ndfc_calculate_ecc routine change the order
of getting the ECC code.
/* The NDFC uses Smart Media (SMC) bytes order */
ecc_code[0] = p[2];
ecc_code[1] = p[1];
ecc_code[2] = p[3];
But in the Correction algorithm when calculating the byte offset
location, the b1 is used as the upper part of the address. Which
again reverse the order making the final byte offset address
location incorrect.
byte_addr = (addressbits[b1] << 4) + addressbits[b0];
The order is change to read it in straight and let the correction
function to revert it to SMC order.
Cc: stable@kernel.org
Signed-off-by: Feng Kan <fkan@amcc.com>
Acked-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Prodyut Hazarika <phazarika@amcc.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The previous implementation breaks the dts binding "mtd-physmap.txt". This
implementation fixes the issue by checking the availability of the reg
property instead of the name property.
Cc: stable@kernel.org
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds DMA mode support for nand prefetch/post-write engine.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds prefetch support to access nand flash in mpu mode.
This patch also adds 8-bit nand support (omap_read/write_buf8).
Prefetch can be used for both 8- and 16-bit devices.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add w90p910 NAND driver for w90p910 evaluation board
based on w90p910,there is a K8F1G08 NAND on my board.
[dwmw2: depend on MTD_PARTITIONS]
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use physmap_of to access RAMs as mtd and add documenation for it. This approach
is a lot less intrusive as adding an of-wrapper around plat-ram.c. As most
extensions of plat-ram.c (e.g. custom map-functions) can't be mapped to the
device tree anyhow, extending physmap_of seems to be the cleanest approach.
Tested with a phyCORE-MPC5121e.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Vitaly Wool <vwool@ru.mvista.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Ken MacLeod <ken@bitsko.slc.ut.us>
Cc: Albrecht Dreß <albrecht.dress@arcor.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch allows i.MX27 to support 2KiB pagesize NAND flash.
We are using a 1.8V NAND flash which datasheet (unfortunately only
available under NDA) says :
Page size: x8: 2,112 bytes (2,048 + 64 bytes).
Without this patch, all sectors are marked as bad eraseblock.
Signed-off-by: Eric Benard <ebenard@eukrea.com>
Acked-by : Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The error handling in the phram driver is pretty bad -- in many places,
errors are silently ignored or logged, but then still ignored in the
return value. So convert all of the code to pass back the correct return
value and log error messages properly (and using the new pr_fmt() helper).
If everything does go smoothly, rather than exit silently, dump a helpful
info message like pretty much every other MTD driver does.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Joern Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Support SST25WF{512,010,020,040} SPI flashes.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The SST SPI flashes are a bit non-standard in that they can be programmed
one byte at a time (including address!), or they can be written two bytes
at a time with auto address incrementing (AAI). The latter form is
obviously much better for performance, so let's use it when possible.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The MTD_TEST config option was added in between the MTD_PARTITIONS config
and its dependent options which causes the resulting menu system to
display incorrectly as MTD_TEST does not depend on MTD_PARTITIONS. So
move it up a few lines where it won't cause a problem.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver lets people use GPIO's for additional address lines in case
their processor does not have enough address lines already.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If MTD_RAM is built as a module, the uClinux map does not work since it
can only be built in to the kernel.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The uClinux map driver doesn't even use partitions, so we shouldn't require
it in order to work properly.
Signed-off-by: Timofei Bondarenko <tim@ipi.ac.ru>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
CC: Greg Ungerer <gerg@uclinux.org>
CC: uclinux-dev@uclinux.org
CC: linux-mtd@lists.infradead.org
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
linux v2.6.31-rc6 can not detect NEC uPD29F064115.
uPD29F064115 is a 16 bit device.
datasheet:
http://www.cn.necel.com/memory/cn/download/M16062EJ2V0DS00.pdf
This applies the same fix as used for SST chips in commit
ca6f12c67e ("jedec_probe: Fix SST 16-bit
chip detection").
Signed-off-by: Hiroshi Ito <ito@mlb.co.jp>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If the erase region was found in the first iteration we read from
regions[-1]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If the erase region was found in the first iteration we read from
eraseregions[-1]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds 4-bit ECC support for large page NAND chips using the new
ECC mode NAND_ECC_HW_OOB_FIRST. The platform data from board-dm355-evm
has been adjusted to use this mode.
The patches have been verified on DM355 device with 2KiB-page Micron
devices using mtd-tests and JFFS2. Error correction up to 4 bits has
also been verified using nandwrite/nanddump utilities.
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds the new mode NAND_ECC_HW_OOB_FIRST in the nand code to
support 4-bit ECC on TI DaVinci devices with large page (up to 2KiB) NAND
chips. This ECC mode is similar to NAND_ECC_HW, with the exception of
read_page API that first reads the OOB area, reads the data in chunks,
feeds the ECC from OOB area to the ECC hw engine and perform any
correction on the data as per the ECC status reported by the engine.
"ECC_HW_OOB_FIRST" name suggested by Thomas Gleixner
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs. The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove the ARM dependency from the generic "onenand" platform device
driver. This change makes the driver useful for other architectures as
well. Needed for the SuperH kfr2r09 board.
Apart from the obvious Kconfig bits, the most important change is the move
away from ARM specific includes and platform data. Together with this
change the only in-tree board code gets an update, and the driver name is
also changed gracefully break potential out of tree drivers.
The driver is also updated to allow NULL as platform data together with a
few changes to make use of resource_size() and dev_name().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
orion_nand_probe lives in .init.text, so using platform_driver_register to
register it is wrong because binding a device after the init memory is
discarded (e.g. via sysfs) results in an oops.
As requested by Nicolas Pitre platform_driver_probe is used instead of
moving the probe function to .devinit.text as proposed initially. This
saves some memory, but devices registered after the driver is probed are
not bound (probably there are none) and binding via sysfs isn't possible.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Joern Engel <joern@logfs.org>
Acked-by: Nicolas Pitre <nico@marvell.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add an omitted unlock to one sst25l_erase fail path.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for the non JEDEC SST25L SPI Flash devices.
[dwmw2: Some cleanups]
Signed-off-by: Andre Renaud <andre@bluewatersys.com>
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: "H Hartley Sweeten" <hartleys@visionengravers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Driver Core: devtmpfs - kernel-maintained tmpfs-based /dev
debugfs: Modify default debugfs directory for debugging pktcdvd.
debugfs: Modified default dir of debugfs for debugging UHCI.
debugfs: Change debugfs directory of IWMC3200
debugfs: Change debuhgfs directory of trace-events-sample.h
debugfs: Fix mount directory of debugfs by default in events.txt
hpilo: add poll f_op
hpilo: add interrupt handler
hpilo: staging for interrupt handling
driver core: platform_device_add_data(): use kmemdup()
Driver core: Add support for compatibility classes
uio: add generic driver for PCI 2.3 devices
driver-core: move dma-coherent.c from kernel to driver/base
mem_class: fix bug
mem_class: use minor as index instead of searching the array
driver model: constify attribute groups
UIO: remove 'default n' from Kconfig
Driver core: Add accessor for device platform data
Driver core: move dev_get/set_drvdata to drivers/base/dd.c
Driver core: add new device to bus's list before probing
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to problems at cam.org, my nico@cam.org email address is no longer
valid. FRom now on, nico@fluxnic.net should be used instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits)
[ARM] Update mach-types
ARM: 5636/1: Move vendor enum to AMBA include
ARM: Fix pfn_valid() for sparse memory
[ARM] orion5x: Add LaCie NAS 2Big Network support
[ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume
ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board
ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board
ARM: 5689/1: Update default config of HP Jornada 700-series machines
ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem
ARM: 5688/1: ks8695_serial: disable_irq() lockup
ARM: 5687/1: fix an oops with highmem
ARM: 5684/1: Add nuc960 platform to w90x900
ARM: 5683/1: Add nuc950 platform to w90x900
ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform
ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver
ARM: 5625/1: fix hard coded 4K resource size in amba bus detection
MMC: MMCI: convert realview MMC to use gpiolib
ARM: 5685/1: Make MMCI driver compile without gpiolib
ARM: implement highpte
ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ
...
Fix up trivial conflict in arch/arm/kernel/signal.c.
It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83f ("KEYS:
Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.
Cleanin up after errors in init_msp_flash().
Also cleanup_msp_flash() attempts to determine the size of
msp_flash with `sizeof(msp_flash) / sizeof(struct mtd_info **)'
This will not work since msp_flash is not an array.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Make mtd_group and mtd_groups static since they are only used in this
file.
[Amended by Artem Bityutskiy]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All of the onenand drivers depend on mtd partition support being compiled
in, so just select it. Fixes up build breakage:
drivers/built-in.o: In function `generic_onenand_remove':
generic.c:(.devexit.text+0x80): undefined reference to `del_mtd_partitions'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes a spelling error that has resulted from copy and
pasting. The location of the error was found using a semantic patch
but the semantic patch was not trying to find these errors. After
looking things over it seemed logical that this change was needed.
The patch also makes sure mtd_list is not being freed if it has not
been allocated
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix the misspelling to match the actual config variable defined in
drivers/mtd/devi ces/Kconfig:
config MTD_DATAFLASH_WRITE_VERIFY
bool "Verify DataFlash page writes"
depends on MTD_DATAFLASH
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/afs.c:244: warning: format ‘%5d’ expects type ‘int’, but argument 4 has type ‘uint64_t’
[dwmw2: fix incorrect 'KB' too]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
1. <linux/io.h> should be included not <asm/io.h>
2. add platform specific header <mach/ts72xx.h>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Correcting debug prints by removing function names from print messages
and using '__func__' macro instead.
Function names were wrong in few places.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Mika Korhonen <mika.j.korhonen@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Arithmetic conversion in the mask computation makes the upper word
of the second argument passed down to mtd->read_oob(), be always 0
(assuming 'offs' being a 64-bit signed long long type, and
'mtd->writesize' being a 32-bit unsigned int type).
This patch applies over the other one adding masking in nftl_write,
"nftl: write support is broken".
Signed-off-by: Dimitri Gorokhovik <dimitri.gorokhovik@free.fr>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Scott James Remnant <scott@canonical.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Write support is broken in NFTL. Fix it.
Signed-off-by: <dimitri.gorokhovik@free.fr>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Scott James Remnant <scott@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
GCC 4.3.3 and 4.4.1 happily moves the dword load instruction out of the
loop in orion_nand_read_buf. This patch makes the instruction volatile
to avoid the issue. I've discussed this at gcc-help, refer to the thread
at
http://gcc.gnu.org/ml/gcc-help/2009-08/msg00187.html
The early clobber is added to avoid the destination registers and the
source register overlapping.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
More testing of NOR flash against power cuts showed that sometimes
eraseblocks may be unwritable, and we cannot really invalidate
them before erasure. But in this case the eraseblock probably
contains garbage anyway, and we do not have to invalidate the
headers. This assumption might be not true, but this is at least
what I have observed. So if we cannot invalidate the headers,
we make sure that the PEB does not contain valid VID header.
If this is true, everything is fine, otherwise we panic.
Useful for debugging problems, compiled in only if UBI debugging
is enabled. This patch also makes the UBI writing function dump
the flash if it fails to write.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The assignment to pos when rb is finally NULL is undefined behaviour.
Upon seeing that assignment, GCC may assume that rb is not NULL, and
the loop condition ``rb'' may be optimised away.
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
There was a bug report recently where UBI prints:
UBI error: ubi_attach_mtd_dev: failed to attach by scanning, error -22
error messages and refuses to attach a PEB. It turned out to be a
buggy flash driver which returned garbage to almost every UBI read.
This patch makes UBI print a better message in such cases. Namely,
if UBI finds 8 or more corrupted PEBs, it prints a warning and
lists the corrupted PEBs.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
In case of NOR flash, UBI zeroes EC and VID headers' magic,
in order to detect interrupted erasures. It first zeroes out
the EC magic, then VID magic. However, if a power cut happens
in between, we'll end up with a corrupted EC header and a valid
VID header, in which case UBI accepts the PEB, but prints a
warning. This patch makes sure we first zero out the VID
magic, then the EC magic, not vice versa. This is just a
small amendment to prevent warning messages.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
If the EC header is corrupted, but the VID header is OK, UBI accepts the
PEB and treats it as "used". However, generally this should not happen.
Print a warning if this happens.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The mtdblks array and its content are prone to race conditions. Introduce
the mutex mtdblks_lock in order to solve this.
[Amended by Artem Bityutskiy]
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver is causing build errors and is no longer needed -- it is obsoleted
by physmap_of.
Signed-off-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Tested-on-PPC64-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
GPMC CS was not freed in omap2_onenand_remove() preventing the module
from reloading after removal.
Signed-off-by: Mika Korhonen <ext-mika.2.korhonen@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fixes the case where CONFIG_MTD_ONENAND_2X_PROGRAM is set and
the real page size differs from mtd_info.writesize.
Signed-off-by: Mika Korhonen <mika.j.korhonen@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Nowadays MTD devices have to be "get" before they can be
used. This has to be done with 'get_mtd_device()'. The
'blktrans_open()' function did not do this and instead
used 'try_module_get()'. Fix this.
Since 'get_mtd_device()' already gets the module, extra
'try_module_get()' is not needed.
This fixes oops when one tries to use mtdblock on top of
gluebi.
Reported-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The patch fixes a bug when converting dev to mtd_info by using the
drvdata of the dev, the previous code used
container_of(dev, struct mtd_info, dev), but won't work for the mtdXro
devices as they created without being contained inside mtd_info structure.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fall back onto thinking everything's OK if either of the sequence
numbers we are asked to compare is zero, which is what was used
before sequence numbers were introduced.
[ Artem: modified the patch to be applicable to upstream UBI, added
big comment ]
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
If we fail in 'ubi_eba_init_scan()', we free
'ubi->volumes[i]->eba_tbl' in there, but also later free it
in 'free_internal_volumes()'. Fix this by assigning NULL
to 'ubi->volumes[i]->eba_tbl' after it is freed.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch fixes a bug in the image seq. number handling in the
scanning level. The assignment of the image_seq was incorrect.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Do not forget to initialize 'gluebi->ubi_num' because otherwise
it will stay 0 even for ubi1 device, and gluebi will open
wrong UBI device when 'gluebi_get_device()' is called.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
arch/arm/mach-ep93xx/include/mach/hardware.h
1. Properly name the include files so that they are loaded
from the <mach/*> directory and not the local directory.
2. Remove including the ts72xx.h header. This header is not
generic to the ep93xx platform. It should only be included
by the ts72xx specific files that require it. The only
two users in the tree are arch/arm/mach-ep93xx/ts72xx.c
and drivers/mtd/nand/ts7250.c.
arch/arm/mach-ep93xx/include/mach/ts72xx.h
1. <linux/io.h> should already be included by any user of this
header. Doing the include here hides it from being needed
by the calling source file.
arch/arm/mach-ep93xx/core.c
1. Remove unnecessary headers. They were probably included
originally due to cut-and-paste from other files.
2. <linux/io.h> should be included not <mach/gpio.h>
arch/arm/mach-ep93xx/adsphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/ts72xx.c
1. Remove unnecessary headers.
arch/arm/mach-ep93xx/ts72xx.c
1. Remove unnecessary headers.
2. Add platform specific header <mach/ts72xx.h>.
drivers/mtd/nand/ts7250.c
1. <linux/io.h> should be included not <asm/io.h>.
2. Add platform specific header <mach/ts72xx.h>.
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The recent "UBI: fix NOR flash recovery" introduced compilation
warnings which were immediately spotted by our linux-next keeper.
This patch fixes them.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This commit fixes NOR flash recovery issues observed with Spansion
S29GL512N NOR.
When NOR erases, it first fills PEBs with zeroes, then sets all bytes
to 0xFF. Filling with zeroes starts from the end of the PEB. And when
power is cut, this results in PEBs containing correct EC and VID headers
but corrupted with zeros at the end. This confuses UBI and it mistakinly
accepts these PEBs and associate them with LEBs.
Fis this issue by zeroing EC and VID magics before erasing PEBs, to
make UBI later refuse zem.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Move the image seq. number handling from I/O level to the scanning
lever, where it really belongs to. Move the @image_seq_set variable
to the @struct ubi_scan_info structure, which exists only during
scanning.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
An image sequence number is added to the UBI erase-counter header
to be able determine if the root file system contains a mixture
of old and new images (because the flashing failed to complete).
A change to nolo is also needed for this to take effect.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The 'paranoid_check_empty()' is bogus because, which is easilly
seen on NOR flash, which has long erase cycles, and which may
easilly end-up with half-erased eraseblocks. In this case the
paranoid check fails. I is just wrong to assume that PEBs which
do not have EC headers always contain all 0xFF. Such assumption
should not be made on the I/O level, which is quite low.
Thus, just kill the check.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds code which makes sure eraseblocks contain all 0xFF
bytes before starting using them. The verification is done only when
debugging checks are enabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
We need to include jiffies.h manually in some cases, and the status
returned from omap_wait() was broken in two separate ways.
Also add cond_resched() to the loop.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use BLOCK_NIL consistently rather than sometimes 0xffff and sometimes
BLOCK_NIL.
The semantic patch that finds this issue is below
(http://www.emn.fr/x-info/coccinelle/). On the other hand, the changes
were made by hand, in part because drivers/mtd/inftlcore.c contains dead
code that causes spatch to ignore a relevant function. Specifically, the
function INFTL_findwriteunit contains a do-while loop, but always takes a
return that leaves the loop on the first iteration.
// <smpl>
@r exists@
identifier f,C;
@@
f(...) { ... return C; }
@s@
identifier r.C;
expression E;
@@
@@
identifier r.f,r.C,I;
expression s.E;
@@
f(...) {
<...
(
I
|
- E
+ C
)
...>
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The m25p16 data sheet from numonyx lists the worst-case bulk erase time
(tBE) as 40 seconds.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Sascha Hauer