Pull HID fixes from Jiri Kosina:
- two cosmetic fixes from Daniel Axtens and Hans de Goede
- fix for I2C command mismatch fix for cp2112 driver from Eudean Sun
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: lower log level for unknown main item tags to warnings
HID: holtekff: move MODULE_* parameters out of #ifdef block
HID: cp2112: Fix I2C_BLOCK_DATA transactions
Given all the effort distros have done with splash-screens to give
users a nice clean boot experience, we really want dmesg --level=err
to not print anything unless there is a real problem with either the
hardware or the kernel. Buggy HID descriptors unfortunately happen
all too often, so lower the log level to warning keep the console
clear of error messages such as:
[ 441.079664] apple 0005:05AC:0239.0003: unknown main item tag 0x0
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If you compile with:
CONFIG_HID_HOLTEK=m
CONFIG_HOLTEK_FF is not set
You get the following warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/hid/hid-holtekff.o
see include/linux/module.h for more information
Fix this by moving the module info out of the #ifdef CONFIG_HOLTEK_FF
block and into the un-guarded part of the file.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Anssi Hannula <anssi.hannula@iki.fi>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The existing driver erroneously treats I2C_BLOCK_DATA and BLOCK_DATA
commands the same.
For I2C_BLOCK_DATA reads, the length of the read is provided in
data->block[0], but the length itself should not be sent to the slave. In
contrast, for BLOCK_DATA reads no length is specified since the length
will be the first byte returned from the slave. When copying data back
to the data buffer, for an I2C_BLOCK_DATA read we have to take care not to
overwrite data->block[0] to avoid overwriting the length. A BLOCK_DATA
read doesn't have this concern since the first byte returned by the device
is the length and belongs in data->block[0].
For I2C_BLOCK_DATA writes, the length is also provided in data->block[0],
but the length itself is not sent to the slave (in contrast to BLOCK_DATA
writes where the length prefixes the data sent to the slave).
This was tested on physical hardware using i2cdump with the i and s flags
to test the behavior of I2C_BLOCK_DATA reads and BLOCK_DATA reads,
respectively. Writes were not tested but the I2C_BLOCK_DATA write change
is pretty simple to verify by inspection.
Signed-off-by: Eudean Sun <eudean@arista.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
Pull HID updates from Jiri Kosina:
- high resolution mode for Dell canvas support, from Benjamin Tissoires
- pen handling fixes for the Wacom driver, from Jason Gerecke
- i2c-hid: Apollo-Lake based laptops improvements, from Hans de Goede
- Input/Core: eraser tool support, from Ping Cheng
- new ALPS touchpad (T4, found currently on HP EliteBook 1000, Zbook
Stduio and HP Elite book x360) supportm from Masaki Ota
- other smaller assorted fixes
* 'for-linus' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (33 commits)
HID: cp2112: fix broken gpio_direction_input callback
HID: cp2112: fix interface specification URL
HID: Wacom: switch Dell canvas into highres mode
HID: wacom: generic: Send BTN_STYLUS3 when both barrel switches are set
HID: sony: Fix SHANWAN pad rumbling on USB
HID: i2c-hid: Add no-irq-after-reset quirk for 0911:5288 device
HID: add backlight level quirk for Asus ROG laptops
HID: cp2112: add HIDRAW dependency
HID: Add ID 044f:b605 ThrustMaster, Inc. force feedback Racing Wheel
HID: hid-logitech: remove redundant assignment to pointer value
HID: wacom: generic: Recognize WACOM_HID_WD_PEN as a type of pen collection
HID: rmi: Check that a device is a RMI device before calling RMI functions
HID: add multi-input quirk for GamepadBlock
HID: alps: add new U1 device ID
HID: alps: add support for Alps T4 Touchpad device
HID: alps: remove variables local to u1_init() from the device struct
HID: alps: properly handle max_fingers and minimum on X and Y axis
HID: alps: Separate U1 device code
HID: alps: delete unnecessary struct u1_dev devInfo
HID: usbhid: Convert timers to use timer_setup()
...
- High resolution mode for DEll canvas support, from Benjamin Tissoires
- A lot of improvements to pen handling in the Wacom driver, from Jason Gerecke
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- cp2112: GPIO error handling and Kconfig fixes from Sébastien Szymanski
- i2c-hid: fixup / quirk for Apollo-Lake based laptops, from Hans de Goede
- Input/Core: add eraser tool support, from Ping Cheng
- small assorted code fixes
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When everything goes smoothly, ret is set to 0 which makes the function
to return EIO error.
Fixes: 8e9faa1546 ("HID: cp2112: fix gpio-callback error handling")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Dell Canvas exports 2 collections for the Pen part. The only
difference between the 2 is that the default one has half the resolution
of the second one.
The Windows driver switches the tablet into the second mode, so we should
behave the same.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Wacom Pro Pen 3D includes a third barrel switch which is intended to
be particularly useful in applications where one frequency uses pan, zoom,
and rotate to navigate around a scene or model. The pen is compatible with
the MobileStudio Pro, 2nd-gen Intuos Pro, and Cintiq Pro. When the third
button is pressed, these devices set both the HID_DG_BARRELSWITCH and
HID_DG_BARRELSWITCH2 usages since their HID descriptors do not include a
usage specific to the button.
Rather than send both BTN_STYLUS and BTN_STYLUS2 when the third button is
pressed, userspace (libinput) has requested that we detect this condition
and report a newly-defined BTN_STYLUS3 event instead. We could define a
quirk specific to devices compatible with the Pro Pen 3D, but the liklihood
of seeing both barrel switch bits set with other pens/devices is low enough
to not worry about (pens mechanically prevent accidental activation of
multiple switches).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The SHANWAN PS3 clone joypad will start its rumble motors as soon as
it is plugged in via USB. As the additional USB interrupt does nothing on
the original PS3 Sixaxis joypads, and makes a number of other
clone joypads actually start sending data, disable that call for
the SHANWAN so the rumble motors aren't started on plug.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Several cheap Apollo Lake based laptops / 2-in-1s use an i2c-hid mt
touchpad which is advertised by the DSDT with an ACPI HID of "SYNA3602",
this touchpad can be found on e.g. the Cube Thinker and the EZBook 3 Pro.
On my "T-bao Tbook air" the i2c-hid driver fails to bind to this touchpad:
"i2c_hid i2c-SYNA3602:00: failed to reset device.".
After some debuging this it seems that this touchpad simply never sends
an interrupt after a reset as expected by the i2c hid driver. This commit
adds a quirk for this device, making i2c_hid_command sleep 100ms after
a reset instead of waiting for an irq, fixing i2c-hid failing to bind to
this touchpad.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On laptops such as Asus GL553VD, setting keyboard backlight levels
does not work. This change enables F3/F4 keys to set backlight levels
(from 0 to 3, total 4 levels) on such laptops.
It is intended only to the following device: 0x0b05 1854:
P: Vendor=0b05 ProdID=1854 Rev=03.02
S: Manufacturer=ITE Tech. Inc.
S: Product=ITE Device(8910)
[jkosina@suse.cz: massage changelog a little bit]
Signed-off-by: Mustafa C Kuscu <mustafakuscu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Otherwise, with HIDRAW=n, the probe function crashes because of null
dereference of hdev->hidraw.
Cc: stable@vger.kernel.org
Fixes: 42cb6b35b9 ("HID: cp2112: use proper hidraw name with minor number")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add ID 044f:b605 ThrustMaster, Inc. force feedback Racing Wheel
Signed-off-by: Viktor Chapliev <viktor-tch@yandex.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
The pointer value is being assigned a value and this is never read, and later
on it is being assigned a new value. This the first assignment is redundant
and can be removed and hence also the variables report and report_list. Cleans
up the clang warning: Value stored to 'value' during its initialization is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The WACOM_PEN_FIELD macro is used to determine if a given HID field should be
associated with pen input. This field includes several known collection types
that Wacom pen data is contained in, but the WACOM_HID_WD_PEN application
collection type is notably missing. This can result in fields within this
kind of collection being completely ignored by the `wacom_usage_mapping`
function, preventing the later '*_event' functions from being notified about
changes to their value.
Fixes: c9c095874a ("HID: wacom: generic: Support and use 'Custom HID' mode and usages")
Fixes: ac2423c975 ("HID: wacom: generic: add vendor defined touch")
Cc: stable@vger.kernel.org
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hid-rmi driver may handle non rmi devices on composite USB devices.
Callbacks need to make sure that the current device is a RMI device before
calling RMI specific functions. Most callbacks already have this check, but
this patch adds checks to the remaining callbacks.
Reported-by: Hendrik Langer <hendrik.langer@gmx.de>
Tested-by: Hendrik Langer <hendrik.langer@gmx.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The GamepadBlock game controller adapter needs HID_QUIRK_MULTI_INPUT
to split it up into two input devices. Without this quirk the
adapter is falsely recognized as only one device and mixes up the
inputs of the two connected controllers.
Signed-off-by: Florian Mueller <contact@petrockblock.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add new U1 device Product ID This device is used on HP Elite book x360 series.
[jkosina@suse.cz: update changelog]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- Define T4 device specification value for support T4 device.
- Creeate "t4_contact_data" and "t4_input_report" structure for decoding and
storing T4-specific data
- Create "t4_calc_check_sum()" function for calculating checksum value to send
to the device. T4 needs to send this value when reading or writing device
address value.
- Create "t4_read_write_register()" function for reading and writing device
address value.
- Create "t4_raw_event()" function for decodin XYZ, palm and button data.
- Replace "MAX_TOUCHES" fixed variable to "max_fingers" variable.
- Add T4 devuce product ID. (0x120C)
T4 device is used on HP EliteBook 1000 series and Zbook Stduio
[jkosina@suse.cz: rewrite changelog]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move dev_ctrl, dev_type, sen_line_num_x, sen_line_num_y, pitch_x, pitch_y,
resolution, btn_info from u1_dev structure to "u1_init()", because these
variables are only used in there.
[jkosina@suse.cz: rewrite changelog]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Create x_min, y_min and max_fingers variables for set correct XY minimum value
and the number of max finger on each devices.
[jkosina@suse.cz: update shortlog]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Create 'static int u1_init()' and factor out U1 device initialization code from
main initialization and introduce per-device 'has_sp' flag.
[jkosina@suse.cz: rewrite changelog]
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- fix for potential out-of-bounds memory access (found by fuzzing,
likely requires specially crafted device to trigger) by Jaejoong Kim
- two new device IDs for elecom driver from Alex Manoussakis
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-elecom: extend to fix descriptor for HUGE trackball
HID: usbhid: fix out-of-bounds bug
Trivial fix to spelling mistake in hid_info message and add line break
to split an overly long line to clean up a checkpatch warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In addition to DEFT, Elecom introduced a larger trackball called HUGE, in
both wired (M-HT1URBK) and wireless (M-HT1DRBK) versions. It has the same
buttons and behavior as the DEFT. This patch adds the two relevant USB IDs
to enable operation of the three Fn buttons on the top of the device.
Cc: Diego Elio Petteno <flameeyes@flameeyes.eu>
Signed-off-by: Alex Manoussakis <amanou@gnu.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hid descriptor identifies the length and type of subordinate
descriptors for a device. If the received hid descriptor is smaller than
the size of the struct hid_descriptor, it is possible to cause
out-of-bounds.
In addition, if bNumDescriptors of the hid descriptor have an incorrect
value, this can also cause out-of-bounds while approaching hdesc->desc[n].
So check the size of hid descriptor and bNumDescriptors.
BUG: KASAN: slab-out-of-bounds in usbhid_parse+0x9b1/0xa20
Read of size 1 at addr ffff88006c5f8edf by task kworker/1:2/1261
CPU: 1 PID: 1261 Comm: kworker/1:2 Not tainted
4.14.0-rc1-42251-gebb2c2437d80 #169
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x292/0x395 lib/dump_stack.c:52
print_address_description+0x78/0x280 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351
kasan_report+0x22f/0x340 mm/kasan/report.c:409
__asan_report_load1_noabort+0x19/0x20 mm/kasan/report.c:427
usbhid_parse+0x9b1/0xa20 drivers/hid/usbhid/hid-core.c:1004
hid_add_device+0x16b/0xb30 drivers/hid/hid-core.c:2944
usbhid_probe+0xc28/0x1100 drivers/hid/usbhid/hid-core.c:1369
usb_probe_interface+0x35d/0x8e0 drivers/usb/core/driver.c:361
really_probe drivers/base/dd.c:413
driver_probe_device+0x610/0xa00 drivers/base/dd.c:557
__device_attach_driver+0x230/0x290 drivers/base/dd.c:653
bus_for_each_drv+0x161/0x210 drivers/base/bus.c:463
__device_attach+0x26e/0x3d0 drivers/base/dd.c:710
device_initial_probe+0x1f/0x30 drivers/base/dd.c:757
bus_probe_device+0x1eb/0x290 drivers/base/bus.c:523
device_add+0xd0b/0x1660 drivers/base/core.c:1835
usb_set_configuration+0x104e/0x1870 drivers/usb/core/message.c:1932
generic_probe+0x73/0xe0 drivers/usb/core/generic.c:174
usb_probe_device+0xaf/0xe0 drivers/usb/core/driver.c:266
really_probe drivers/base/dd.c:413
driver_probe_device+0x610/0xa00 drivers/base/dd.c:557
__device_attach_driver+0x230/0x290 drivers/base/dd.c:653
bus_for_each_drv+0x161/0x210 drivers/base/bus.c:463
__device_attach+0x26e/0x3d0 drivers/base/dd.c:710
device_initial_probe+0x1f/0x30 drivers/base/dd.c:757
bus_probe_device+0x1eb/0x290 drivers/base/bus.c:523
device_add+0xd0b/0x1660 drivers/base/core.c:1835
usb_new_device+0x7b8/0x1020 drivers/usb/core/hub.c:2457
hub_port_connect drivers/usb/core/hub.c:4903
hub_port_connect_change drivers/usb/core/hub.c:5009
port_event drivers/usb/core/hub.c:5115
hub_event+0x194d/0x3740 drivers/usb/core/hub.c:5195
process_one_work+0xc7f/0x1db0 kernel/workqueue.c:2119
worker_thread+0x221/0x1850 kernel/workqueue.c:2253
kthread+0x3a1/0x470 kernel/kthread.c:231
ret_from_fork+0x2a/0x40 arch/x86/entry/entry_64.S:431
Cc: stable@vger.kernel.org
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
(introduced by 686fef928b ("timer: Prepare to change timer callback
argument type")) to pass the timer pointer explicitly. Adds pointer back to
hid_device for multitouch.
[jkosina@suse.cz: extend changelog a little bit as asked for by Benjamin]
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: linux-input@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 3e70969e44.
This commit causes a few problems for userspace. The most noteworthy are
problems related to the distinguishing of different pens and pointer jumps
when entering proximity. Userspace is written with the expectation that a
pen will provide its tool ID and serial number (if available) in the very
first in-prox report. By sending BTN_TOOL_PEN when the tablet starts
communicating rather than waiting until a tool ID/serial number is
available, userspace ends up treating all pens as being the same and
lacking a serial number. Similarly, userspace assumes that the first
report will contain X/Y data, but by marking the pen as being in-prox
without an X/Y coordinate, userspace ends up warping the pen to the last-
known X/Y location. As of commit 5b40104edf ("HID: wacom: generic: Reset
events back to zero when pen leaves") this means warping to (0,0).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID subsystem fixes from Jiri Kosina:
- buffer management size fix for i2c-hid driver, from Adrian Salido
- tool ID regression fixes for Wacom driver from Jason Gerecke
- a few small assorted fixes and a few device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: multitouch: Support ALPS PTP stick with pid 0x120A"
HID: hidraw: fix power sequence when closing device
HID: wacom: Always increment hdev refcount within wacom_get_hdev_data
HID: wacom: generic: Clear ABS_MISC when tool leaves proximity
HID: wacom: generic: Send MSC_SERIAL and ABS_MISC when leaving prox
HID: i2c-hid: allocate hid buffers for real worst case
HID: rmi: Make sure the HID device is opened on resume
HID: multitouch: Support ALPS PTP stick with pid 0x120A
HID: multitouch: support buttons and trackpoint on Lenovo X1 Tab Gen2
HID: wacom: Correct coordinate system of touchring and pen twist
HID: wacom: Properly report negative values from Intuos Pro 2 Bluetooth
HID: multitouch: Fix system-control buttons not working
HID: add multi-input quirk for IDC6680 touchscreen
HID: wacom: leds: Don't try to control the EKR's read-only LEDs
HID: wacom: bits shifted too much for 9th and 10th buttons
pr_err() messages should terminated with a new-line to avoid
other messages being concatenated onto the end.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some tablets report eraser usage to indicate the eraser tool tip
is touching the surface. But, hidinput_configure_usage didn't
support the usage, which led it falls into default as ABS_MISC.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Computes and forwards the device timestamp according to the specification.
Many devices use a 16-bit timestamp field, with a resolution of 100us,
therefore rolling around very frequently (every 6.5 seconds). To make sure
there is no ambiguity, the timestamp reported to the input stack reset to
0 whenever the time between 2 received events is greater than
MAX_TIMESTAMP_INTERVAL (1 second).
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add descriptive info to prompt string so that someone can know what
a Retrode is. Drop an unneeded blank line.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit fcaa4a07d2.
As noted by Masaki [1], 0x120A + trackpoint will not be used in mass
production machines, so remove the ID accordingly.
[1] http://www.spinics.net/lists/linux-input/msg53222.html
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Linus Torvalds