Add flags for Octal mode I/O data transfer
Required for the SPI controller which can do the data transfer (TX/RX)
on 8 data lines e.g. NXP FlexSPI controller.
SPI_TX_OCTAL: transmit with 8 wires
SPI_RX_OCTAL: receive with 8 wires
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices such as the TPO TPG110 display panel require
a "high-impedance turn-around", in effect a clock cycle after
switching the line from output to input mode.
Support this in the GPIO driver to begin with. Other driver
may implement it if they can, it is unclear if this can
be achieved with anything else than GPIO bit-banging.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This attribute works the same was as the identically named attribute
for PCI, AMBA, and platform devices. For reference, see:
commit 3cf3857134 ("ARM: 8256/1: driver coamba: add device binding
path 'driver_override'")
commit 3d713e0e38 ("driver core: platform: add device binding path
'driver_override'")
commit 782a985d7a ("PCI: Introduce new device binding path using
pci_dev.driver_override")
If the name of a driver is written to this attribute, then the device
will bind to the named driver and only the named driver.
The device will bind to the driver even if the driver does not list the
device in its id table. This behavior is different than the driver's
bind attribute, which only allows binding to devices that are listed as
supported by the driver.
It can be used to bind a generic driver, like spidev, to a device.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The of_find_spi_device_by_node() helper function is useful for other
modules too. Export the funciton as GPL like all other spi helper
functions and make it available if CONFIG_OF is enabled, because it isn't
related to the CONFIG_OF_DYNAMIC context. Finally add a stub if
CONFIG_OF isn't enabled, so others must not care about it.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the appropriate SPDX license identifier and drop the previous
license text.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This provides a SPI operation mode which changes chip select after every
word, used by some devices such as ADCs and DACs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlugGWgTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0OAqB/99Zk/yjUqw3q8mQ9TcDyurMrllpNYm
n9KshwKOc1wyfHsbPMke+ytCJHmMpNDKbv80Dk5aTNBvbeNN9OZdcqonGfVfulEB
hhZy6X4wN6QwX6HpIeWl52o4V4zLd0skeZOqMod/4RQKQvG7kCVVetKFfzMBxYpP
4B+jVLg/L/lVsbNqXe53A59C0myg/lkCBFL9uWmiUaAScS/eeWmHX/Z+Guf3DTjo
eR0ZoB55HeovL8AsTV0xAwjae+YM6LMElptXLF/+AlaFmW4WmuRGuU2tCXh+SaHU
/VzwLgekzd1hplHc8tX1Nhdr4qJhI6tcpQOu+IelTqZ/Z/JlpIruaJVB
=sMBd
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlugGesTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LpbB/9eeBHjpAthphCZ1Q87oUtqn0dbhV9j
+djnjM3BgJX+3T3vl6fnOtyD2MPg/sGX8pMePEcVqUSRp+StY5tCO++zbR7maMxs
Czw5GslnJJ9CG6T7xx1ZE1vWAIeWywH7Pw98daFJpQkj17BEhGrrqSbpctJaRdSy
3e5nZvc3mWQ5k4ttmK+C9MTa6XV3ReaHDfJaagXWM7bykV6mDwVh6dyx4QJ7kwht
Ti+MQ+SYZndySXTFoborSss+5zgYIJ5nKr07PvOsNrjlk2p3hoU+y7MuU+RB9zzs
XP9dgZKSoLWbFdCspaC6DtcT1P2HLQRi5kBfdc8xlUCupa6Y2Jt3Hms1
=TFpo
-----END PGP SIGNATURE-----
Merge tag 'spi-cs-word' into spi-4.20
spi: Provide SPI_CS_WORD
This provides a SPI operation mode which changes chip select after every
word, used by some devices such as ADCs and DACs.
This adds a new SPI mode flag, SPI_CS_WORD, that is used to indicate
that a SPI device requires the chip select to be toggled after each
word that is transferred.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some SPI controllers, after each word size (specified by bits_per_word)
transimission, the hardware need some delay to make sure the slave has enough
time to receive the whole data.
So introducing one new 'word_delay' field of struct spi_tansfer for slave
devices to set this inter word delay time.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This API has been replaced by the spi_mem_xx() one, its only user
(spi-nor) has been converted to spi_mem_xx() and all SPI controller
drivers that were implementing the ->spi_flash_xxx() hooks are also
implementing the spi_mem ones. So we can safely get rid of this API.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some controllers are exposing high-level interfaces to access various
kind of SPI memories. Unfortunately they do not fit in the current
spi_controller model and usually have drivers placed in
drivers/mtd/spi-nor which are only supporting SPI NORs and not SPI
memories in general.
This is an attempt at defining a SPI memory interface which works for
all kinds of SPI memories (NORs, NANDs, SRAMs).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now struct spi_master is used for both SPI master and slave controllers,
it makes sense to rename it to struct spi_controller, and replace
"master" by "controller" where appropriate.
For now this conversion is done for SPI core infrastructure only.
Wrappers are provided for backwards compatibility, until all SPI drivers
have been converted.
Noteworthy details:
- SPI_MASTER_GPIO_SS is retained, as it only makes sense for SPI
master controllers,
- spi_busnum_to_master() is retained, as it looks up masters only,
- A new field spi_device.controller is added, but spi_device.master is
retained for compatibility (both are always initialized by
spi_alloc_device()),
- spi_flash_read() is used by SPI masters only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for registering SPI slave controllers using the existing SPI
master framework:
- SPI slave controllers must use spi_alloc_slave() instead of
spi_alloc_master(), and should provide an additional callback
"slave_abort" to abort an ongoing SPI transfer request,
- SPI slave controllers are added to a new "spi_slave" device class,
- SPI slave handlers can be bound to the SPI slave device represented
by an SPI slave controller using a DT child node named "slave",
- Alternatively, (un)binding an SPI slave handler to the SPI slave
device represented by an SPI slave controller can be done by
(un)registering the slave device through a sysfs virtual file named
"slave".
From the point of view of an SPI slave protocol handler, an SPI slave
controller looks almost like an ordinary SPI master controller. The only
exception is that a transfer request will block on the remote SPI
master, and may be cancelled using spi_slave_abort().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an interface analogous to ->can_dma() for spi_flash_read()
interface. This will enable SPI controller drivers to inform SPI core
when not to do DMA mappings.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Invoke the proper function while initializing
a dynamically allocated spi_message to avoid
NULL pointer dereference during resources deallocation.
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Generic device properties support statically defined property sets. For
them to be usable, we need to attach these property sets before devices
are registered and probed. Allowing to attach property list to
spi_board_info structure will allow non-ACPI non-DT boards switch to using
generic properties and get rid of custom platform data.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SPI masters require slave selection before the transfer
can begin [1]. The SPI framework currently selects the chip using
either 1) the internal CS mechanism or 2) the GPIO CS, but not both.
This patch adds a new master->flags define to indicate both the GPIO
CS and the internal chip select mechanism should be used.
Tested On:
Altera CycloneV development kit
Compile tested for build errors on x86_64 (allyesconfigs)
[1] DesignWare dw_apb_ssi Databook, Version 3.20a (page 39)
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify spi_write() and spi_read() using the spi_sync_transfer()
helper.
This requires moving spi_sync_transfer() up.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Recently a maximum transfer size was was introduced in struct spi_master.
However there are also spi controllers with a maximum message size, e.g.
fsl-espi has a max message size of 64KB.
Introduce a hook max_message_size to deal with such limitations.
Also make sure that spi_max_transfer_size doesn't return greater values
than spi_max_message_size, even if hook max_transfer_size is not set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current SPI code attempts to use bus_lock_mutex for two purposes. One
is to implement spi_bus_lock() which grants exclusive access to the bus.
The other is to serialize access to the physical hardware. This duplicate
purpose causes confusion which leads to cases where access is not locked
when a caller holds the bus lock mutex. Fix this by splitting out the I/O
functionality into a new io_mutex.
This means taking both mutexes in the DMA path, replacing the existing
mutex with the new I/O one in the message pump (the mutex now always
being taken in the message pump) and taking the bus lock mutex in
spi_sync(), allowing __spi_sync() to have no mutex handling.
While we're at it hoist the mutex further up the message pump before we
power up the device so that all power up/down of the block is covered by
it and there are no races with in-line pumping of messages.
Reported-by: Rich Felker <dalias@libc.org>
Tested-by: Rich Felker <dalias@libc.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Few SPI devices provide accelerated read interfaces to read from
SPI-NOR flash devices. These hardwares also support DMA to transfer data
from flash to memory either via mem-to-mem DMA or dedicated slave DMA
channels. Hence, add support for DMA in order to improve throughput and
reduce CPU load.
Use spi_map_buf() to get sg table for the buffer and pass it to SPI
driver.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If hook spi_flash_read is implemented the fast flash read feature
is enabled for all devices attached to the respective master.
In most cases there is just one flash chip, however there are also
devices with more than one flash chip, namely some WiFi routers.
Then the fast flash read feature can be used for the first chip only.
OpenWRT implemented an own handling of this case, using controller_data
element of spi_device to hold the information whether fast flash read
can be used for a device.
This patch adds hook flash_read_supported to spi_master which is
used to extend spi_flash_read_supported() by checking whether the
fast flash read feature can be used for a specific spi_device.
If the hook is not implemented the default behavior is to allow
fast flash read for all devices (if spi_flash_read is implemented).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The kernel-doc has to be just before the structure definition but the one
for struct spi_replaced_transfers was before a structure declaration and
that confuses kernel-doc which complains with the following build error:
.//include/linux/spi/spi.h:933: error: Cannot parse struct or union!
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes docbook parsing error because documentation
is not directly followed by the structure, but typedef
used in structure.
Reordering should solve that issue.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In addition to providing direct access to SPI bus, some spi controller
hardwares (like ti-qspi) provide special port (like memory mapped port)
that are optimized to improve SPI flash read performance.
This means the controller can automatically send the SPI signals
required to read data from the SPI flash device.
For this, SPI controller needs to know flash specific information like
read command to use, dummy bytes and address width.
Introduce spi_flash_read() interface to support accelerated read
over SPI flash devices. SPI master drivers can implement this callback to
support interfaces such as memory mapped read etc. m25p80 flash driver
and other flash drivers can call this make use of such interfaces. The
interface should only be used with SPI flashes and cannot be used with
other SPI devices.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add spi_split_transfers_maxsize method that splits
spi_transfers transparently into multiple transfers
that are below the given max-size.
This makes use of the spi_res framework via
spi_replace_transfers to allocate/free the extra
transfers as well as reverting back the changes applied
while processing the spi_message.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the spi_replace_transfers method that can get used
to replace some spi_transfers from a spi_message with other
transfers.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI resource management framework used while processing a spi_message
via the spi-core.
The basic idea is taken from devres, but as the allocation may happen
fairly frequently, some provisioning (in the form of an unused spi_device
pointer argument to spi_res_alloc) has been made so that at a later stage
we may implement reuse objects allocated earlier avoiding the repeated
allocation by keeping a cache of objects that we can reuse.
This framework can get used for:
* rewriting spi_messages
* to fullfill alignment requirements of the spi_master HW
* to fullfill transfer length requirements
(e.g: transfers need to be less than 64k)
* consolidate spi_messages with multiple transfers into a single transfer
when the total transfer length is below a threshold.
* reimplement spi_unmap_buf without explicitly needing to check if it has
been mapped
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In Windows it is up to the SPI host controller driver to handle the ACPI
DeviceSelection as it likes. The SPI core does not take any part in it.
This is different in Linux because we always expect to have chip select in
range of 0 .. master->num_chipselect - 1.
In order to support this in Linux we need a way to allow the driver to
translate between ACPI DeviceSelection field and Linux chip select number
so provide a new optional hook ->fw_translate_cs() that can be used by a
driver to handle translation and call this hook if set during SPI slave
ACPI enumeration.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix kernel-doc warning for missing struct field notation.
..//include/linux/spi/spi.h:540: warning: No description found for parameter 'max_transfer_size'
[Meaningful subject -- broonie]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some SPI controllers it is not feasible to transfer arbitrary amount
of data at once.
When the limit on transfer size is a few kilobytes at least it makes
sense to use the SPI hardware rather than reverting to gpio driver.
The protocol drivers need a way to check that they do not sent overly
long messages, though.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the spi_loopback_test driver there is the need to initialize
a spi_message that is filled with values from a static structure.
Applying spi_message_init to such a prefilled structure results in
all the settings getting reset to zero, which is not what we want.
Copying each field of spi_message separately instead always includes
the risk that some new fields have not been implemented in the copying
code.
So here we introduce a version of spi_message_init called
spi_message_init_no_memset that does not fill the structure
with zero first, but only initializes the relevant list_heads.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Uninline spi_unregister_device() in preparation of adding more code to
it. Add kerneldoc documentation while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add spi_register_driver helper macro that adds THIS_MODULE to
spi_driver for the registering driver. We rename and modify
the existing spi_register_driver to enable this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When building docs with make htmldocs, warnings about not having
a description for the return value are reported, i.e:
warning: No description found for return value of 'spi_write'
Fix these by following the kernel-doc conventions explained in
Documentation/kernel-doc-nano-HOWTO.txt.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
report transfer sizes as a histogram via the following files:
/sys/class/spi_master/spi*/statistics/transfer_bytes_histo_*
/sys/class/spi_master/spi*/spi*.*/statistics/transfer_bytes_histo_*
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following 'make htmldocs' warnings:
.//include/linux/spi/spi.h:71: warning: No description found for parameter 'lock'
.//include/linux/spi/spi.h:71: warning: Excess struct/union/enum/typedef member 'clock' description in 'spi_statistics'
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown