* Mark __flush_icache_range as a function that can't be probed since its
used by the kprobe code.
* Fix an issue with single stepping and async exceptions. We need to
ensure that we dont get an async exception (external, decrementer, etc)
while we are attempting to single step the probe point.
Added a check to ensure we only handle a single step if its really
intended for the instruction in question.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It was discussed that global arch_initcall() is preferred way to probe
QE GPIOs, so let's use it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ports B and C pins programming is changed to get SCC2 UART and FCC3
ethernet work.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we have an L2CSR register (e500mc) we need to flush the L2 before going
to nap. We use the HW flush mechanism provided in that register.
The code reuses the CPU_FTR_604_PERF_MON bit as it is no longer used by
any code in the kernel. Additionally we didn't reuse the exist L2CR
feature bit as this is intended for the 7xxx L2CR register and L2CSR
is part of the new Freescale "Book-E" registers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The e500 core enter DOZE/NAP power-saving modes when the core go to
cpu_idle routine.
The power management default running mode is DOZE, If the user
echo 1 > /proc/sys/kernel/powersave-nap
the system will change to NAP running mode.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new e500mc core from Freescale is based on the e500v2 but with the
following changes:
* Supports only the Enhanced Debug Architecture (DSRR0/1, etc)
* Floating Point
* No SPE
* Supports lwsync
* Doorbell Exceptions
* Hypervisor
* Cache line size is now 64-bytes (e500v1/v2 have a 32-byte cache line)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes following section mismatch:
WARNING: arch/powerpc/sysdev/built-in.o(.text+0x11d8): Section mismatch in
reference from the function qe_reset() to the function
.init.text:cpm_muram_init()
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is very trivial patch. We're transitioning to the cpm_muram_*
calls. That's it.
Less trivial changes:
- BD_SC_* defines were defined in the cpm.h and qe.h, so to avoid redefines
we remove BD_SC from the qe.h and use cpm.h along with cpm_muram_*
prototypes;
- qe_muram_dump was unused and thus removed;
- added some code to the cpm_common.c to support legacy QE bindings
(data-only node name).
- For convenience, define qe_* calls to cpm_*. So drivers need not to be
changed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is patch adds board file, device tree, and defconfig for the new
board, made by Freescale Semiconductor Inc. and Logic Product Development.
Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.
Not supported in this patch:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM NAND driver);
2. FHCI USB (supported with FHCI driver).
3. QE Serial UCCs (tested to not work with ucc_uart driver, reason
unknown, yet);
4. ADC AD7843 (tested to work, but support via device tree depends on
major SPI rework, GPIO API, etc);
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed to access QE GPIOs via Linux GPIO API.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- split and export __par_io_config_pin() out of par_io_config_pin(), so we
could use the prefixed version with GPIO LIB API;
- rename struct port_regs to qe_pio_regs, and place it into qe.h;
- rename #define NUM_OF_PINS to QE_PIO_PINS, and place it into qe.h.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds a function to the qe_lib to setup QE USB clocks routing.
To setup clocks safely, cmxgcr register needs locking, so I just reused
ucc_lock since it was used only to protect cmxgcr.
The idea behind placing clocks routing functions into the qe_lib is that
later we'll hopefully switch to the generic Linux Clock API, thus, for
example, FHCI driver may be used for QE and CPM chips without nasty #ifdefs.
This patch also fixes QE_USB_RESTART_TX command definition in the qe.h.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
GTM stands for General-purpose Timers Module and able to generate
timer{1,2,3,4} interrupts. These timers are used by the drivers that
need time precise interrupts (like for USB transactions scheduling for
the Freescale USB Host controller as found in some QE and CPM chips),
or these timers could be used as wakeup events from the CPU deep-sleep
mode.
Things unimplemented:
1. Cascaded (32 bit) timers (1-2, 3-4).
This is straightforward to implement when needed, two timers should
be marked as "requested" and configured as appropriate.
2. Super-cascaded (64 bit) timers (1-2-3-4).
This is also straightforward to implement when needed, all timers
should be marked as "requested" and configured as appropriate.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds local bus nodes for Flash and CAN to the DTS file
of the TQM8560 module (tqm8560.dts).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some TQM85xx boards could be equipped with up to 1 GiB (NOR) flash
memory and therefore a modified memory map is required and setup by
the board loader. This patch adds an appropriate DTS file.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Like for the TQM5200, the vendor prefix "tqc," is now used for all
TQM85xx modules from TQ-Components GmbH (http://www.tqc.de) in the
corresponding DTS files.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
All the maintained platforms are now in arch/powerpc, so the old
arch/ppc stuff can now go away.
Acked-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: John Linn <john.linn@xilinx.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When I changed irq_alloc_host() to take an of_node
(52964f87c64e6c6ea671b5bf3030fb1494090a48: "Add an optional
device_node pointer to the irq_host"), I botched the reference
counting semantics.
Stephen pointed out that it's irq_alloc_host()'s business if
it needs to take an additional reference to the device_node,
the caller shouldn't need to care.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we do the call to of_address_to_resource() first, then we don't
need to worry about freeing the irq_host (which the code doesn't do
currently anyway).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we do the call to of_address_to_resource() first, then we don't
need to worry about freeing the irq_host (which the code doesn't do
currently anyway).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we do the call to irq_of_parse_and_map() first, then we don't
need to worry about freeing the irq_host.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This eliminates this minor boot-time debugging error message:
[ 1.316451] calling add_pcspkr+0x0/0x84
[ 1.316478] initcall add_pcspkr+0x0/0x84 returned -19 after 0 msecs
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 5 of 5: add the Kconfig entry for the C2K board.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 4 of 5: this is the default config for the board. In this
configuration the kernel is going to try to boot from MTD
partition 3 on the NOR flash (see c2k.dts for details about
the partitioning of the flash).
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 3 of 5: driver for the board. At this time it is very generic
and similar to its original, the driver for the prpmc2800.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 2 of 5: support for the board in arch/powerpc/boot.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 1 of 5: DTS file describing the board peripherals. As far as I
know all peripherals except the FPGA are listed in there (I did not
include the FPGA because a lot of work is needed there).
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the following warning, introduced by commit
475ca391b4 (mpic: Deal with bogus NIRQ
in Feature Reporting Register):
CC arch/powerpc/sysdev/mpic.o
arch/powerpc/sysdev/mpic.c: In function 'mpic_alloc':
arch/powerpc/sysdev/mpic.c:1146: warning: suggest explicit braces to avoid ambiguous 'else'
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ehea driver was recently changed[1] to use walk_memory_resource() to
detect the system's memory layout. However, walk_memory_resource() is
available only when memory hotplug is enabled. So CONFIG_EHEA was
made to depend on MEMORY_HOTPLUG [2], but it is inappropriate for a
network driver to have such a dependency.
Make the declaration of walk_memory_resource() and its powerpc
implementation (ehea is powerpc-specific) unconditionally available.
[1] 48cfb14f8b
"ehea: Add DLPAR memory remove support"
[2] fb7b6ca2b6
"ehea: Add dependency to Kconfig"
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During the next merge window, pci_name()'s return value will become
const, so use the new dev_set_name() instead to avoid the warning (from
linux-next):
arch/powerpc/kernel/pci_64.c: In function 'of_create_pci_dev':
arch/powerpc/kernel/pci_64.c:193: warning: passing argument 1 of 'sprintf' discards qualifiers from pointer target type
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When building a signal or a ucontext, we can incorrectly set the MSR_VEC
bit of the kernel pt_regs->msr before returning to userspace if the task
-ever- used VMX.
This can lead to funny result if that stack used it in the past, then
"lost" it (ie. it wasn't enabled after a context switch for example)
and then called get_context. It can end up with VMX enabled and the
registers containing values from some other task.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This corrects the names of two CONFIG_ variables.
Note that the CONFIG_MPC86XADS fix uncovers another bug
(with mpc866_ads_defconfig) that will require fixing:
<-- snip -->
...
arch/powerpc/boot/dtc -O dtb -o arch/powerpc/boot/mpc866ads.dtb -b 0 /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts
DTC: dts->dtb on file "/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/dts/mpc866ads.dts"
WRAP arch/powerpc/boot/cuImage.mpc866ads
powerpc64-linux-ld: arch/powerpc/boot/cuboot-mpc866ads.o: No such file: No such file or directory
make[2]: *** [arch/powerpc/boot/cuImage.mpc866ads] Error 1
<-- snip -->
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: add workaround for bug in ASUS A7V600 BIOS (rev 1005)
PCI/x86: fix up PCI stuff so that PCI_GOANY supports OLPC
Change the name of the device from "rtc-ds1374" to just "ds1374", to match
what all other RTC drivers do. I seem to remember that this name was
chosen to avoid possible confusion with an older ds1374 driver, but that
driver was removed 3 months ago.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Although if people have questions about ARCnet, perhaps it's _better_
for them to be mailing dwmw2@cam.ac.uk about it...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include limits.h to get a definition of PATH_MAX.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We lost the marking of SIGWINCH as being OK to receive during stub
execution, causing a panic should that happen.
Cc: Benedict Verheyen <benedict.verheyen@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86_64 defines either memcpy or __memcpy depending on the gcc version, and
it looks like UML needs to follow that in its exporting.
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes os_get_task_size locate the bottom of the address space,
as well as the top. This is for systems which put a lower limit on mmap
addresses. It works by manually scanning pages from zero onwards until a
valid page is found.
Because the bottom of the address space may not be zero, it's not
sufficient to assume the top of the address space is the size of the
address space. The size is the difference between the top address and
bottom address.
[jdike@addtoit.com: changed the name to reflect that this function is
supposed to return the top of the process address space, not its size and
changed the return value to reflect that. Also some minor formatting
changes]
Signed-off-by: Tom Spink <tspink@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removed duplicated include file "kern_util.h" in
arch/um/drivers/ubd_kern.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Protection against the host's time going backwards (eg, ntp activity on
the host) by keeping track of the time at the last tick and if it's
greater than the current time, keep time stopped until the host catches
up.
Cc: Nix <nix@esperi.org.uk>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As some m68k machines have plenty of libc5 binaries in active use, enable
CONFIG_COMPAT_BRK by default.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This BIOS claims the VIA 8237 south bridge to be compatible with VIA 586,
which it is not.
Without this patch, I get the following warning while booting,
among others,
| PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
| ------------[ cut here ]------------
| WARNING: at arch/x86/pci/irq.c:265 pirq_via586_get+0x4a/0x60()
| Modules linked in:
| Pid: 1, comm: swapper Not tainted 2.6.26-rc4-00015-g1ec7d99 #1
| [<c0119fd4>] warn_on_slowpath+0x54/0x70
| [<c02246e0>] ? vt_console_print+0x210/0x2b0
| [<c02244d0>] ? vt_console_print+0x0/0x2b0
| [<c011a413>] ? __call_console_drivers+0x43/0x60
| [<c011a482>] ? _call_console_drivers+0x52/0x80
| [<c011aa89>] ? release_console_sem+0x1c9/0x200
| [<c0291d21>] ? raw_pci_read+0x41/0x70
| [<c0291e8f>] ? pci_read+0x2f/0x40
| [<c029151a>] pirq_via586_get+0x4a/0x60
| [<c02914d0>] ? pirq_via586_get+0x0/0x60
| [<c029178d>] pcibios_lookup_irq+0x15d/0x430
| [<c03b895a>] pcibios_irq_init+0x17a/0x3e0
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a6763>] kernel_init+0x73/0x250
| [<c03b87e0>] ? pcibios_irq_init+0x0/0x3e0
| [<c0114d00>] ? schedule_tail+0x10/0x40
| [<c0102dee>] ? ret_from_fork+0x6/0x1c
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c03a66f0>] ? kernel_init+0x0/0x250
| [<c010324b>] kernel_thread_helper+0x7/0x1c
| =======================
| ---[ end trace 4eaa2a86a8e2da22 ]---
and IRQ trouble later,
| irq 10: nobody cared (try booting with the "irqpoll" option)
Now that's an VIA 8237 chip, so pirq_via586_get shouldn't be called
at all; adding this workaround to via_router_probe() fixes the
problem for me.
Amazingly I have a 2.6.23.8 kernel that somehow works fine ... I'll
never understand why.
Signed-off-by: Bertram Felgenhauer <int-e@gmx.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
Fix divide by zero error in build_clear_page() and build_copy_page()
[MIPS] Fix typo in header guard
[MIPS] Fix build error - Delete debugging crap that crept in with CMP
[MIPS] Add accessors for random register.
[MIPS] IP27: misc fixes
[MIPS] IP27: Fix clockevent setup
[MIPS] IP27: Fix bootmem memory setup
[MIPS] remove CONFIG_CPU_R4000 line from Makefile
[MIPS] Fix check for valid stack pointer during backtrace
[MIPS] Add missing braces to pte_mkyoung
[MIPS] R4700: Fix build_tlb_probe_entry
[MIPS] Alchemy: dbdma: add API to delete custom DDMA device ids.
[MIPS] Alchemy: export get_au1x00_speed for modules
Previously, one would have to specifically choose CONFIG_OLPC and
CONFIG_PCI_GOOLPC in order to enable PCI_OLPC. That doesn't really work
for distro kernels, so this patch allows one to choose CONFIG_OLPC and
CONFIG_PCI_GOANY in order to build in OLPC support in a generic kernel (as
requested by Robert Millan).
This also moves GOOLPC before GOANY in the menuconfig list.
Finally, make pci_access_init return early if we detect OLPC hardware.
There's no need to continue probing stuff, and pci_pcbios_init
specifically trashes our settings (we didn't run into that before because
PCI_GOANY wasn't supported).
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Here is an attempt to translate the prompt and help text into something
which is legible and, as a bonus, correct.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kumar Gala