For pcie nic, after setting link speed and there is no link driver does not need
to do phy reset until link up.
For some pcie nics, to do this will also reset phy speed down counter and prevent
phy from auto speed down.
This patch fix the issue reported in following link.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1547151
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware now tells us that the reset is done by passing a magic value
via register. Use it to shorten the wait in case this is supported.
With old firmware, we still wait until the timeout is reached.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On AT91 SoCs, the User Register (USRIO) exposes a switch to configure the
"Reduced" or "Traditional" version of the Media Independent Interface
(RMII vs. MII or RGMII vs. GMII).
As on the older EMAC version, on GMAC, this switch is set by default to the
non-reduced type of interface, so use the existing capability and extend it to
GMII as well. We then keep the current logic in the macb_init() function.
The capabilities of sama5d2, sama5d4 and sama5d3 GEM interface are updated in
the macb_config structure to be able to properly enable them with a traditional
interface (GMII or MII).
Reported-by: Romain HENRIET <romain.henriet@l-acoustics.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is OF-DPA specific, used only there, similar to
ofdpa_port->ageing_time. So move it to OF-DPA code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the scenario where slowpath configuration isn't passing due to
various pause configurations affecting the chip, the theoretical time
required in worst-case-scenario to empty hw fifos sufficiently to
guarantee that slowpath configuration would flow is currently
insufficient.
This increases such a drain request to the theoretical maximum.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle a new message from the MFW, one that indicate that the transciever
state has changed, and log that into the system logs.
Signed-off-by: Zvi Nachmani <Zvi.Nachmani@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver interaction with the managemnt firmware is done via mailbox
commands which the management firmware periodically sample, as well
as placing of additional data in set places in the shared memory.
Each PF has a single designated mailbox address, and all flows that
require messaging to the management should use it.
This patch does 2 things:
1. It re-defines the critical section surrounding the mailbox sending -
that section should include the setting of the shared memory as well as
the sending of the command [otherwise a race might send a command with
the data of a different command].
2. It moves the locking scheme from using mutices into using spinlocks.
This lays the groundwork for sending MFW commands from non-sleepable
contexts.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is configured for Multi-function mode, some older management
firmware might incorrectly notify interfaces of link changes while they
haven't requested the physical link configuration to be set.
This can create bizzare race conditions where unloading interfaces are
getting notified that the link is up.
Let the driver compensate - store the logical requested state of the link
and don't propagate notifications after protocol driver explicitly
requires the link to be unset.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't hide varibles used by the logging macros.
Miscellanea:
o Use the more common ##__VA_ARGS__ extension
o Add missing newlines to formats
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rocker, ageing time is a per-port attribute, so the next time the FDB
cleanup timer fires should be set according to the lowest ageing time.
This will later allow us to delete the BR_MIN_AGEING_TIME macro, which was
added to guarantee minimum ageing time in the bridge layer, thereby breaking
existing behavior.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c62987bbd8 ("bridge: push bridge setting ageing_time down to
switchdev") added a check for minimum and maximum ageing time, but this
breaks existing behaviour where one can set ageing time to 0 for a
non-learning bridge.
Push this check down to the driver and allow the check in the bridge
layer to be removed. Currently ageing time 0 is refused by the driver,
but we can later add support for this functionality.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce offloading of skbedit mark action.
For example, to mark with 0x1234, all TCP (ip_proto 6) packets arriving
to interface ens9:
# tc qdisc add dev ens9 ingress
# tc filter add dev ens9 protocol ip parent ffff: \
flower ip_proto 6 \
indev ens9 \
action skbedit mark 0x1234
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parse tc_cls_flower_offload into device specific commands and program
the hardware to classify and act accordingly.
For example, to drop ICMP (ip_proto 1) packets from specific smac, dmac,
src_ip, src_ip, arriving to interface ens9:
# tc qdisc add dev ens9 ingress
# tc filter add dev ens9 protocol ip parent ffff: \
flower ip_proto 1 \
dst_mac 7c:fe:90:69:81:62 src_mac 7c:fe:90:69:81:56 \
dst_ip 11.11.11.11 src_ip 11.11.11.12 indev ens9 \
action drop
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend ndo_setup_tc() to support ingress tc offloading. Will be used by
later patches to offload tc flower filter.
Feature is off by default and could be enabled by issuing:
# ethtool -K eth0 hw-tc-offload on
Offloads flow table is dynamically created when first filter is
added.
Rules are saved in a hash table that is maintained by the consumer (for
example - the flower offload in the next patch).
When last filter is removed and no filters exist in the hash table, the
offload flow table is destroyed.
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the vlan and main flow tables to use priority 1. This will allow
the upcoming TC offload logic to use a higher priority (0) for the
offload steering table.
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restricting handle to TC_H_ROOT breaks the old instantiation of mqprio
to setup a hardware qdisc. This patch relaxes the test, to only check the
type.
Fixes: 08fb1da ("net/mlx5e: Support DCBNL IEEE ETS")
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to handle flow table entry destinations only if the action
associated with the rule is forwarding (MLX5_FLOW_CONTEXT_ACTION_FWD_DEST).
Fixes: 26a8145390 ('net/mlx5_core: Introduce flow steering firmware commands')
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Makefile and Kconfig required to make the driver build.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethernet support for MediaTek SoCs from the MT7623 family. These have
dual GMAC. Depending on the exact version, there might be a built-in
Gigabit switch (MT7530). The core does not have the typical DMA ring setup.
Instead there is a linked list that we add descriptors to. There is only
one linked list that both MACs use together. There is a special field
inside the TX descriptors called the VQID. This allows us to assign packets
to different internal queues. By using a separate id for each MAC we are
able to get deterministic results for BQL. Additionally we need to
provide the core with a block of scratch memory that is the same size as
the RX ring and data buffer. This is really needed to make the HW datapath
work. Although the driver does not support this yet, we still need to
assign the memory and tell the core about it for RX to work.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Michael Lee <igvtee@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
'commit 55482edc25
("qede: Add slowpath/fastpath support and enable hardware GRO")'
introduces below error when compiling net-next with "make ARCH=x86_64"
drivers/built-in.o: In function `qede_rx_int':
qede_main.c:(.text+0x6101a0): undefined reference to `tcp_gro_complete'
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o While the driver is in the middle of a MB completion processing
and it receives a spurious MB interrupt, it is mistaken as a good MB
completion interrupt leading to premature completion of the next MB
request. Fix the driver to guard against this by checking the current
state of MB processing and ignore the spurious interrupt.
Also added a stats counter to record this condition.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o atomic_t usage is incorrect as we are not implementing
any atomicity.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Queue Set Configuration code was always reserving room for a
Forwarded interrupt Queue even in the cases where we weren't using it.
Figure out how many Ports and Queue Sets we can support. This depends on
knowing our Virtual Function Resources and may be called a second time
if we fall back from MSI-X to MSI Interrupt Mode. This change fixes that
problem.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids a race condition where a system that has network devices set up
to be automatically configured and we get the first Port Link Status
message from the firmware on the Asynchronous Firmware Event Queue before
we've enabled interrupts. If that happens, we end up losing the interrupt
and never realizing that the links has actually come up.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iff dma_map_single() fails, 'rxdesc' should point to the last filled RX
descriptor, so that it can be marked as the last one, however the driver
would have already advanced it by that time. In order to fix that, only
fill an RX descriptor once all the data for it is ready.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a low memory situation, if netdev_alloc_skb() fails on a first RX ring
loop iteration in sh_eth_ring_format(), 'rxdesc' is still NULL. Avoid
kernel oops by adding the 'rxdesc' check after the loop.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to create flow rule that forward packets
to the first flow table in the next priority (next priority
could be the first priority in the next namespace or the
next priority in the same namespace).
This feature could be used for DONT_TRAP rules or rules
that only want to mark the packet with flow tag.
In order to do it optimally, each flow table has list
of all rules that point to this flow table,
when a flow table is destroyed/created, we update the list
head correspondingly.
This kind of rule is created when destination is NULL and
action is MLX5_FLOW_CONTEXT_ACTION_FWD_NEXT_PRIO.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Create an empty flow table in the end of NIC rx namesapce.
Adding this flow table simplify the implementation of "forward
to next prio" rules.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add pci_error_handler callbacks to support for pcie advanced error
recovery.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the more useful port statistics in ethtool -S for the PF device.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include some of the port error counters (e.g. crc) in ->ndo_get_stats64()
for the PF device.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gather periodic port statistics if the device is PF and link is up. This
is triggered in bnxt_timer() every one second to request firmware to DMA
the counters.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow all autoneg speeds aupported by firmware to be advertised. If
the advertising parameter is 0, then all supported speeds will be
advertised.
Remove BNXT_ALL_COPPER_ETHTOOL_SPEED which is no longer used as all
supported speeds can be advertised.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The supported bits and advertising bits in ethtool have the same
definitions. The same is true for the firmware bits. So use the
common function to handle the conversion for both supported and
advertising bits.
v2: Don't use parentheses on function return.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And report actual pause settings to ETHTOOL_GPAUSEPARAM to let ethtool
resolve the actual pause settings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the conversion of pause bits and add one extra call layer so
that the same refactored function can be reused to get the link partner
advertisement bits.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
It will always be passed if the soc is tested the loopback cases. This
patch will fix this bug.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Documentation/power/devices.txt
The driver should not use device_set_wakeup_enable() which is the policy
for user to decide.
Using device_init_wakeup() to initialize dev->power.should_wakeup and
dev->power.can_wakeup on driver initialization.
And use device_may_wakeup() on suspend to decide if WoL function should
be enabled on NIC.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise it might be back on resume right after going to suspend in
some hardware.
Reported-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adapter->pcicfg resource is either mapped via pci_iomap() or
derived from adapter->db. During be_remove() this resource was ignored
and so could remain mapped after remove.
Add a flag to track whether adapter->pcicfg was mapped or not, then
use that flag in be_unmap_pci_bars() to unmap if required.
Fixes: 25848c901 ("use PCI MMIO read instead of config read for errors")
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures hardware to use GRO and adds support
for fastpath APIs to handle HW aggregated packets.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds mainly structures and APIs prototype changes
in order to give support for qede slowpath/fastpath support
for the same.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFD_SYSCON depends on HAS_IOMEM so when selecting it avoid unmet
direct dependencies.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_linearize fails, the driver should drop the packet
instead of trying to copy it into the bounce buffer.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The descriptor queues for sending (SDQs) and receiving (RDQs) packets
are managed by two counters - producer and consumer - which are both
16-bit in size. A queue is considered full when the difference between
the two equals the queue's maximum number of descriptors.
However, if the producer counter overflows, then it's possible for the
full queue check to fail, as it doesn't take the overflow into account.
In such a case, descriptors already passed to the device - but for which
a completion has yet to be posted - will be overwritten, thereby causing
undefined behavior. The above can be achieved under heavy load (~30
netperf instances).
Fix that by casting the subtraction result to u16, preventing it from
being treated as a signed integer.
Fixes: eda6500a98 ("mlxsw: Add PCI bus implementation")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we only support one VLAN filtering bridge we need to associate a
reference count with it, so that when the last port netdev leaves it, we
would know that a different bridge can be offloaded to hardware.
When a LAG device is memeber in a bridge and port netdevs are leaving
the LAG, we should always decrement the bridge's reference count, as it's
incremented for any port in the LAG.
Fixes: 4dc236c317 ("mlxsw: spectrum: Handle port leaving LAG while bridged")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv->mdio->irq used to be allocated and required freeing, but it
is now a fixed sized array and should no longer be free'd.
Issue detected using static analysis with CoverityScan
Fixes: e7f4dc3536 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv->mdio->irq used to be allocated and required freeing, but it
is now a fixed sized array and should no longer be free'd.
Issue detected using static analysis with CoverityScan
Fixes: e7f4dc3536 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
is actually "active high". Thanks for Troy Kisky for pointing
that out.
Since the patch is in linux-next, this patch is incremental and doesn't
replace the original patch.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:115:15-21: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable workaround for MPC8548E erratum eTSEC 106,
"Excess delays when transmitting TOE=1 large frames".
(see commit 53fad77375 "gianfar: Enable eTSEC-20 erratum w/a
for P2020 Rev1")
This erratum was fixed in Rev 3.1.x.
Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern Intel systems supports cross timestamping of the network device
clock and Always Running Timer (ART) in hardware. This allows the
device time and system time to be precisely correlated. The timestamp
pair is returned through e1000e_phc_get_syncdevicetime() used by
get_system_device_crosststamp(). The hardware cross-timestamp result
is made available to applications through the PTP_SYS_OFFSET_PRECISE
ioctl which calls e1000e_phc_getcrosststamp().
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: kevin.b.stanton@intel.com
Cc: kevin.j.clarke@intel.com
Cc: hpa@zytor.com
Cc: jeffrey.t.kirsher@intel.com
Cc: netdev@vger.kernel.org
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Christopher S. Hall <christopher.s.hall@intel.com>
[jstultz: Reworked to use new interface, commit message tweaks]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Since ezchip network driver is written with big endian EZChip platform it
is necessary to add support for little endian architecture.
The first issue is that the order of the bits in a bit field is
implementation specific. So all the bit fields are removed.
Named constants are used to access necessary fields.
And the second one is that network byte order is big endian.
For example, data on ethernet is transmitted with most-significant
octet (byte) first. So in case of little endian architecture
it is important to swap data byte order when we read it from
register. In case of unaligned access we can use "get_unaligned_be32"
and in other case we can use function "ioread32_rep" which reads all
data from register and works either with little endian or big endian
architecture.
And then when we are going to write data to register we need to restore
byte order using the function "put_unaligned_be32" in case of
unaligned access and in other case "iowrite32_rep".
The last little fix is a space between type and pointer to observe
coding style.
Signed-off-by: Lada Trimasova <ltrimas@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Tal Zilcer <talz@ezchip.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface is opened (in be_open()) the routine
be_enable_if_filters() must be called to switch on the basic filtering
capabilities of an interface that are not changed at run-time.
These include the flags UNTAGGED, BROADCAST and PASS_L3L4_ERRORS.
Other flags such as MULTICAST and PROMISC must be enabled later by
be_set_rx_mode() based on the state in the netdev/adapter struct.
be_enable_if_filters() routine is wrongly trying to enable MULTICAST flag
without checking the current adapter state. This can cause the RX_FILTER
cmds to the FW to fail. This patch fixes this problem by only enabling
the basic filtering flags in be_enable_if_filters().
The VF must be able to issue RX_FILTER cmd with any filter flag, as long
as the PF allowed those flags (if_cap_flags) in the iface it provisioned
for the VF. This rule is applicable even when the VF doesn't have the
FILTMGMT privilege. There is a bug in BE3 FW that wrongly fails RX_FILTER
multicast programming cmds on VFs that don't have FILTMGMT privilege.
This patch also helps in insulating the VF driver from be_open failures due
to the FW bug. A fix for the BE3 FW issue will be available in
versions >= 11.0.283.0 and 10.6.334.0
Reported-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally return IS_ERR(priv->base) which is 1 instead of
PTR_ERR(priv->base) which is the error code.
Fixes: 6c821bd9ed ('net: Add MOXA ART SoCs ethernet driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new NET_DEVLINK infrastructure can be a loadable module, but the drivers
using it might be built-in, which causes link errors like:
drivers/net/built-in.o: In function `mlx4_load_one':
:(.text+0x2fbfda): undefined reference to `devlink_port_register'
:(.text+0x2fc084): undefined reference to `devlink_port_unregister'
drivers/net/built-in.o: In function `mlxsw_sx_port_remove':
:(.text+0x33a03a): undefined reference to `devlink_port_type_clear'
:(.text+0x33a04e): undefined reference to `devlink_port_unregister'
There are multiple ways to avoid this:
a) add 'depends on NET_DEVLINK || !NET_DEVLINK' dependencies
for each user
b) use 'select NET_DEVLINK' from each driver that uses it
and hide the symbol in Kconfig.
c) make NET_DEVLINK a 'bool' option so we don't have to
list it as a dependency, and rely on the APIs to be
stubbed out when it is disabled
d) use IS_REACHABLE() rather than IS_ENABLED() to check for
NET_DEVLINK in include/net/devlink.h
This implements a variation of approach a) by adding an
intermediate symbol that drivers can depend on, and changes
the three drivers using it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 09d4d087cd ("mlx4: Implement devlink interface")
Fixes: c4745500e9 ("mlxsw: Implement devlink interface")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic_capability struct was defined incorrectly. The last two
elements of the struct are in the wrong order. In addition, the number
element should be 64-bit. Byteswapping functions are updated
as well.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaa ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in a case of error, dev_err is using fman->dev
before its initialization and "(NULL device *)" is printed.
This patch fixes this issue.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch manages the case when you have an Ethernet MAC with
a "fixed link", and not connected to a normal MDIO-managed PHY device.
The test of phy_bus_name was not helpful because it was never affected
and replaced by the mdio test node.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Left over from c24588afc5
("atl1c: using fixed TXQ configuration for l2cb and l1c")
Signed-off-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts the changed init order from commit 3647bc35bd
("dwc_eth_qos: Reset hardware before PHY start") and makes another fix
for the race.
It turned out that the reset state machine of the dwceqos hardware
requires PHY clocks to be present in order to complete the reset
cycle.
To plug the race with the phy state machine we defer link speed
setting until the hardware init has finished.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since debug is hardcoded to 3, the defaults in the DWCEQOS_MSG_DEFAULT
macro are never used, which does not seem to be the intended behaviour
here. Set debug to -1 like other drivers so that DWCEQOS_MSG_DEFAULT is
actually used by default.
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we are in non-atomic context here we can pass GFP_KERNEL to
dma_alloc_coherent(). This enables use of the CMA.
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prepare for using the CMA, we can not be in atomic context when
de-allocating DMA buffers.
The tx lock was needed only to protect the hw reset against the xmit
handler. Now we briefly grab the tx lock while stopping the queue to
make sure no thread is inside or will enter the xmit handler.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xmit handler and the tx_reclaim tasklet had a race on the tx_free
variable which could lead to a tx timeout if tx_free was updated after
the tx complete interrupt.
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function t4vf_wait_dev_ready() is already called in t4vf_prep_adapter(),
no need to call it again in adap_init0().
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a new function t4vf_fl_pkt_align() and use the same in SGE
initialization code to find out freelist packet alignment
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T4 and T5 hardware will not coalesce Free List PCI-E Fetch Requests if
the Host Driver provides more Free List Pointers than the Fetch Burst
Minimum value. So if we set FBMIN to 64 bytes and the Host Driver
supplies 128 bytes of Free List Pointer data, the hardware will issue two
64-byte PCI-E Fetch Requests rather than a single coallesced 128-byte
Fetch Request. T6 fixes this. So, for T4/T5 we set the FBMIN value to 128
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use freelist capacity instead of freelist size while checking, if
freelist needs to be refilled
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF administrative mac addresses (stored in the PF driver) are
initialized to zero when the PF driver starts up.
These addresses may be modified in the PF driver through ndo calls
initiated by iproute2 or libvirt.
While we allow the PF/host to change the VF admin mac address from zero
to a valid unicast mac, we do not allow restoring the VF admin mac to
zero. We currently only allow changing this mac to a different unicast mac.
This leads to problems when libvirt scripts are used to deal with
VF mac addresses, and libvirt attempts to revoke the mac so this
host will not use it anymore.
Fix this by allowing resetting a VF administrative MAC back to zero.
Fixes: 8f7ba3ca12 ('net/mlx4: Add set VF mac address support')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reported-by: Moshe Levi <moshele@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The limit of 63 is only for virtual functions while the actual enforcement
was for VFs plus physical functions, fix that.
Fixes: e57968a10b ('net/mlx4_core: Support the HA mode for SRIOV VFs too')
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the mac and vlan register/unregister/replace functions, the driver locks
the mac table mutex (or vlan table mutex) on both ports.
We move to use mutex_lock_nested() to prevent warnings, such as the one below.
[ 101.828445] =============================================
[ 101.834820] [ INFO: possible recursive locking detected ]
[ 101.841199] 4.5.0-rc2+ #49 Not tainted
[ 101.850251] ---------------------------------------------
[ 101.856621] modprobe/3054 is trying to acquire lock:
[ 101.862514] (&table->mutex#2){+.+.+.}, at: [<ffffffffa079c10e>] __mlx4_register_mac+0x87e/0xa90 [mlx4_core]
[ 101.874598]
[ 101.874598] but task is already holding lock:
[ 101.881703] (&table->mutex#2){+.+.+.}, at: [<ffffffffa079c0f0>] __mlx4_register_mac+0x860/0xa90 [mlx4_core]
[ 101.893776]
[ 101.893776] other info that might help us debug this:
[ 101.901658] Possible unsafe locking scenario:
[ 101.901658]
[ 101.908859] CPU0
[ 101.911923] ----
[ 101.914985] lock(&table->mutex#2);
[ 101.919595] lock(&table->mutex#2);
[ 101.924199]
[ 101.924199] * DEADLOCK *
[ 101.924199]
[ 101.931643] May be due to missing lock nesting notation
Fixes: 5f61385d2e ('net/mlx4_core: Keep VLAN/MAC tables mirrored in multifunc HA mode')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Suggested-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the HW VPort counters for traffic (rx/tx packets/bytes)
statistics is wrong. This is because frames dropped due to steering or
out of buffer will be counted as received. To fix that, we move to use
the packet/bytes accounting done by the driver for what the netdev
reports out.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support [...]')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sum up rx/tx bytes in software as we do for rx/tx packets, to be reported
in upcoming statistics fix.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon changing num_channels, reset the RSS indirection table to
match the new value.
Fixes: 2d75b2bc8a ('net/mlx5e: Add ethtool RSS configuration options')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should modify TIRs explicitly to apply the new RSS configuration.
The light ndo close/open calls do not "refresh" them.
Fixes: 2d75b2bc8a ('net/mlx5e: Add ethtool RSS configuration options')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Readers/Writers lock for SW timecounter was acquired without disabling
interrupts on local CPU.
The problematic scenario:
* HW timestamping is enabled
* Timestamp overflow periodic service task is running on local CPU and
holding write_lock for SW timecounter
* Completion arrives, triggers interrupt for local CPU.
Interrupt routine calls napi_schedule(), which triggers rx/tx
skb process.
An attempt to read SW timecounter using read_lock is done, which is
already locked by a writer on the same CPU and cause soft lockup.
Add irqsave/irqrestore for when using the readers/writers lock for
writing.
Fixes: ef9814deaf ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool LRO enable/disable is broken, as of today we only modify TCP
TIRs in order to apply the requested configuration.
Hardware requires that all TIRs pointing to the same RQ should share the
same LRO configuration. For that all other TIRs' LRO fields must be
modified as well.
Fixes: 5c50368f38 ('net/mlx5e: Light-weight netdev open/stop')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the MLX5E_CQ_HAS_CQES optimization flag, the following buggy
flow might occur:
- Suppose RX is always busy, TX has a single packet every second.
- We poll a single TX cqe and clear its flag.
- We never arm it again as RX is always busy.
- TX CQ flag is never changed, and new TX cqes are not polled.
We revert this optimization.
Fixes: e586b3b0ba ('net/mlx5: Ethernet Datapath files')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just updates the driver to the version fully
tested on STi platforms. This version is Oct_2015.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a threshold now used to also limit the skb allocation
when use zero-copy. This is to avoid that there are incoherence
in the ring due to a failure on skb allocation under very
aggressive testing and under low memory conditions.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to allow this driver to copy tiny frames during the reception
process. This is giving more stability while stressing the driver on STi
embedded systems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_bus_name can be NULL when "fixed-link" property isn't used.
Then, since "stmmac: do not poll phy handler when attach a switch",
phy_bus_name ptr needs to be checked before strcmp is called.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids to call the stmmac_adjust_link when
the driver is connected to a switch by using the FIXED_PHY
support. Prior this patch the phydev->irq was set as PHY_POLL
so periodically the phy handler was invoked spending useless
time because the link cannot actually change.
Note that the stmmac_adjust_link will be called just one
time and this guarantees that the ST glue logic will be
setup according to the mode and speed fixed.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fill the first descriptor just before granting
the DMA engine so at the end of the xmit.
The patch takes care about the algorithm adopted to mitigate the
interrupts, then it fixes the last segment in case of no fragments.
Moreover, this new implementation does not pass any "ter" field when
prepare the descriptors because this is not necessary.
The patch also details the memory barrier in the xmit.
As final results, this patch guarantees the same performances
but fixing a case if small datagram are sent. In fact, this
kind of test is impacted if no coalesce is done.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dirty index can be updated out of the loop where all the
tx resources are claimed. This will help on performances too.
Also a useless debug printk has been removed from the main loop.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch "inline" get_tx_owner and get_ls routines. It Results in a
unique read to tdes0, instead of three, to check TX_OWN and LS bits,
and other status bits.
It helps improve driver TX path by removing two uncached read/writes
inside TX clean loop for enhanced descriptors but not for normal ones
because the des1 must be read in any case.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to optimize the way to manage the TDES inside the
xmit function. When prepare the frame, some settings (e.g. OWN
bit) can be merged. This has been reworked to improve the tx
performances.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RDES0 register can be read several times while doing RX of a
packet.
This patch slightly improves RX path performance by reading rdes0
once for two operation: check rx owner, get rx status bits.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize tx_clean by avoiding a des3 read in stmmac_clean_desc3().
In ring mode, TX, des3 seems only used when xmit a jumbo frame.
In case of normal descriptors, it may also be used for time
stamping.
Clean it in the above two case, without reading it.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
last_segment field is read twice from dma descriptors in stmmac_clean().
Add last_segment to dma data so that this flag is from priv
structure in cache instead of memory.
It avoids reading twice from memory for each loop in stmmac_clean().
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the code pulls out the length field when
unmapping a buffer directly from the descriptor. This will result
in an uncached read to a dma_alloc_coherent() region. There is no
need to do this, so this patch simply puts the value directly into
a data structure which will hit the cache.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chun-Hao Lin