Impact: driver could possibly stomp on resources outside of its scope
{mchehab@redhat.com: I got two versions of the same patch (identical,
except for whitespacing). One authored by Andy Burns and another
authored by Suresh Siddha. Due to that, I'm applying the one that has
less CodingStyle errors. I'm also adding both comments and the SOB's for
both patches, since they are both interesting}
Suresh Siddha commented:
Alexey Fisher reported:
> resource map sanity check conflict: 0xcfeff800 0xcff007ff 0xcfe00000
> 0xcfefffff PCI Bus 0000:01
BAR base is located in the middle of the 4K page and the hardcoded
size argument makes the request span two pages causing the conflict.
Fix the hard coded size argument in ioremap().
Andy Burns commented:
I have already sent this patch on the linux-dvb list, but it didn't get
much attention, so re-sending direct, I hope you all don't mind.
While attempting to run mythtv in a xen domU, I encountered problems
loading the driver for my saa7134 card, with an error from ioremap().
This error was due to the driver allocating an incorrectly sized mmio
area, which was trapped by xen's permission checks, but this would go
un-noticed on a kernel without xen.
My card has a 1K sized mmio area, I've had information that other cards
have 2K areas, perhaps others have different sizes, yet the driver
always attempts to map 4K. I realise that the granularity of mapping is
the page size, which typically would be 4K, but unless the card's base
address happens to fall on a 4K boundary (mine does not) then the
base+4K will end up spanning two pages, and this is when the error
occurs under xen.
My patch uses the pci_resource_len macro to determine the size required
for the user's particular card, instead of the hardcoded 4K value. I've
tested with a couple of printk() inside ioremap() that the start address
and size do get rounded to the closest page boundary.
With this patch I am able to successfully load the saa7134 driver and
run mythtv under xen with my card, subject to correct pollirq settings
in case of shared IRQ, I am still seeing occasional DMA panics, which I
think are related to swiotlb handling by dom0/domU, usually the panic
occurs when changing mux, once tuned to a mux, 12 hour continuous
recordings are possible without errors.
Reported-by: Alexey Fisher <bug-track@fisher-privat.net>
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andy Burns <andy@burns.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The kernel number of a v4l2 node (e.g. videoX, radioX or vbiX) is now
independent of the minor number. So instead of using the minor field
of the video_device struct one has to use the num field: this always
contains the kernel number of the device node.
I forgot about this when I did the v4l2 core change, so this patch
converts all drivers that use it in one go. Luckily the change is
trivial.
Cc: michael@mihu.de
Cc: mchehab@infradead.org
Cc: corbet@lwn.net
Cc: luca.risolia@studio.unibo.it
Cc: isely@pobox.com
Cc: pe1rxq@amsat.org
Cc: royale@zerezo.com
Cc: mkrufky@linuxtv.org
Cc: stoth@linuxtv.org
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is patch for solve this regression. Load ir-kbd-i2c module when remote is i2c type.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SAA7134_IRQ1_INTE_RA2_3 and SAA7134_IRQ1_INTE_RA2_2 are used for planar video,
not for TS.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/saa7134/saa7134-core.c:366: warning:
'saa7134_buffer_requeue' defined but not used
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The type and type2 fields were unused and so could be removed.
Instead add a vfl_type field that contains the type of the video
device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When saa7134_board_init2 runs, it immediately overwrites the current value
(set earlier from module parameter) of tuner_type with the static values,
and then does autodetection. This patch moves the tuner_addr copy to earlier
in saa7134_initdev and removes the tuner_type copy from saa7134_board_init2.
Autodetection could still potentially change to the wrong tuner type, but it
is now possible to override the default type for the card again.
My card's tuner is configured with autodetection from eeprom, so I don't
need to manually set the tuner. I've checked that the autodetection still
works for my card.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Reviewed-by: Hermann Pitton <hermann-pitton@arcor.de>
Cc: Brian Marete <bgmarete@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The field 'dev' is not the video device, but the parent of the video device.
Rename accordingly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also remove some blank lines that were used to split compat code at -devel
tree.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
patch 779169257208 made the variable mask unnecessary.
This patch just removes the declaration.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This causes a problem with the audio mute on some cards and is done
implictly in the audio initialization code.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes reported problems when trying to add a 9th device into a
system.
Signed-off-by: Alan McIvor <alan.mcivor@reveal.co.nz>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tuner refactoring broke support of tuners with LNA configurations 1 and 2
for both, analog TV and DVB-T.
Additionally, this patch initializes the saa713x gpios defined by the gpiomask
at driver init to avoid undefined stated at dvb.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the following saa7134 xc3028 based boards:
132 -> AVerMedia Cardbus TV/Radio (E506R) [1461:f436]
133 -> AVerMedia Hybrid TV/Radio (A16D) [1461:f936]
134 -> Avermedia M115 [1461:a836]
135 -> Compro VideoMate T750 [185b:c900]
This is based on a original patch thanks to Markus Rechberger that added xc3028
gpio init code for the above boards.
This patch moves saa7134_tuner_callback to saa7134-cards, originally used only
by tda8290 DVB-S boards. The callback was made more generic to support other
tuners.
Currently, it supports both tda8290 and xc2028/xc3028 tuners. Added also the
basis for xc5000 tuner callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Static memory is always initialized with 0.
- Replaced in some cases C99 comments for /* */
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are several parts of saa7134_board_init2() that calls tuner modules. We
should first load tuner, otherwise, the commands will fail.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VBI were broken, since there weren't any function handlers for it. This patch
fixes it, by removing the vbi_template, using, instead video_template.
This also saves some space at the data segment.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
move some tv-audio initialization code out of tvaudio thread,
and call it on resume too.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
First the saa7134_initdev waits between saa7134_hwinit1
and saa7134_hwinit2 , thus it is probably wise to do the same in saa7134_resume
some hardware probably needs this.
Call saa7134_irq_video_signalchange in .resume like in saa7134_resume to make
saa7134_resume mirror perfectly the saa7134_initdev although
this call isn't strictly necessary in the saa7134_initdev,
but it won't harm anyway.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*dev->insuspend = 1 should be set before synchronize_irq
*ACK interrupts after synchronize_irq, to make sure there aren't
pending interrupts.
*Add barrier before we restart interrupts so the handler will 100%
see the dev->insuspend
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pci_save_state should be called before pci_set_power_state
and pci_restore_state after pci_set_power_state
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7134_buffer_requeue() and set_tvnorm() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Correct wrong sized spinlock flags, form int to unsigned long.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The saa7134 video driver starts dropping frames when used together with the
saa7134-alsa driver. Frames are dropped because when an audio event is waiting
the driver simply ignores the interrupt and passes it on to the saa7134-alsa
interrupt handler. The alsa interrupt handler in turn acknowledges all types
of events thus clearing the pending video events as well. Fix by only masking
out the audio event in the video interrupt handler and by only acknowledging
the audio event in the alsa driver.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Calling saa7134_ir_stop at suspend is no good idea
for saa7134 cards without remote control.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes few more problems I found in my saa7134 resume code:
* Race between IRQ handler and .suspend()/.resume() functions
* Removes timeout timers on active buffers - those
buffers will be recaptured after resume
* Adds suspend/resume for IR code - probably
necessary if using polling mode
* Adds #ifdef CONFIG_PM overs suspend code
* Runs a quirk in set_tvnorm in suspend/resume too
* Rearranges the order of calls in saa7134_resume to
be exactly as in saa7134_initdev thus the card is
initialized in exactly the same way
* Since DMA audio capture suspend/resume isn't yet supported,
avoid re-enabling it on resume for now
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A couple loops weren't changed because they expected the loop iterator
to be left as NULL if the list was empty. Maybe the code should just
check for that first, then loop?
Adjust some of the loop logic to be simpler.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*Disable DMA explictly on suspend
*Enable DMA on resume, after all buffers were configured
*Disable overlay on resume - apps should enable it when X is resumed
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
By "capturing interlaced video" I mean that card ensures that top field
is really top and vice versa (I think it takes the filed ID from signal)
Properly turn on/off that support depending on signal state
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds support for suspend/resume for core of saa7134
Should fix bug#7220
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
PCI-dependent videobuf_foo methods were renamed as videobuf_pci_foo.
Also, videobuf_dmabuf is now part of videobuf-dma-sg private struct.
So, to access it, a subroutine call is needed.
This patch renames all occurences of those function calls to be
consistent with the video-buf split.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
http://thread.gmane.org/gmane.comp.video.video4linux/34978/focus=34981
Reviewed-by: Ricardo Cerqueira <v4l@cerqueira.org>
Since at least kernel 2.6.12-rc2, module.h includes moduleparm.h. This
patch removes all occurences of moduleparm.h from drivers/media files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Besides power saving, this puts the AGC output of the tda8290
to tristate. This is necessary for some hybrid boards which
don't use a multiplexer for the AGC
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the following compile error with CONFIG_MODULES=n:
CC drivers/media/video/saa7134/saa7134-core.o
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/drivers/media/video/saa7134/saa7134-core.c:979:24: error: macro "request_submodules" passed 1 arguments, but takes just 0
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/drivers/media/video/saa7134/saa7134-core.c: In function 'saa7134_initdev':
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/drivers/media/video/saa7134/saa7134-core.c:979: error: 'request_submodules' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/drivers/media/video/saa7134/saa7134-core.c:979: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/drivers/media/video/saa7134/saa7134-core.c:979: error: for each function it appears in.)
make[5]: *** [drivers/media/video/saa7134/saa7134-core.o] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change supplies a more generic version of the tuner callback.
The tuner struct now has a function pointer
int (*tuner_callback) (void *dev, int command, int arg)
additionally to a int config parameter.
both can be set through the TUNER_SET_TYPE_ADDR client call.
Note that the meaning of the parameters depend on the tuner type.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains
- new tuning code for the tda827xa silicon tuner.
- controls the preamplifier of some boards with this tuner.
- support for the Philips Tiger S hybrid DVB-T reference design.
- reworked the saa7134-dvb modulue to get rid of most of the
small board specific functions.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This function allows to set, clear and tristate the GPIO ports.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In case the exact board type needs to be determined by probing
or evaluating the eeprom, this flag allows to still set the
board type via the card=xx insmod option.
This is an extract of a patch by Francis Barber.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
We could go and work out if the target object is AGP or PCI but the
corner case of an Athlon 64 era box with PCI video is sufficiently
unusual it doesn't seem worth the extra work, at least until other cases
if any pop up.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Two different exports with the same name are not a good idea:
$ grep -r EXPORT_SYMBOL\(dmasound_init\) *
drivers/media/video/saa7134/saa7134-core.c:EXPORT_SYMBOL(dmasound_init);
sound/oss/dmasound/dmasound_core.c:EXPORT_SYMBOL(dmasound_init);
$
This patch renames the saa7134 dmasound_{init,exit} to
saa7134_dmasound_{init,exit}.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We should no longer try to load the tda9887 module, because it no longer
exists. The tda9887 driver has been merged into the tuner module.
This patch removes all instances of request_module("tda9887") from
the following video4linux drivers: bttv, cx88, em28xx and saa7134.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Suresh Siddha