pcnet_cs,serial_cs:
add cis of KTI PE520 pcmcia network card,
and serial card(Sierra Wireless AC860).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMSC Ethernet Transceivers (LAN88710, LAN8710, LAN8720, LAN8187,
LAN8700, LAN83C185) provide a mechanism to conserve power when
the device is not connected to an active link partner
(Energy Detect Mode).
So this patch enables the Energy Detect power-down mode
for these Transceivers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
current the Rx/Tx FIFO size settings cause problem
when four UEC ethernets work simultaneously.
eg: GETH1, UEM-J15, GETH2, UEC-J5 on 8569MDS board
$ ifconfig eth0 10.193.20.166
$ ifconfig eth1 10.193.20.167
$ ifconfig eth2 10.193.20.168
then
$ ifconfig eth3 10.193.20.169
The fourth ethernet will cause all of interface broken,
you cann't ping successfully any more.
The patch fix this issue for MPC8569 Rev1.0 and Rev2.0
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New handlers are added here to handle:
1) Small frames (<256 bytes) in a single small buffer. Allocate a new
skb and copy the frame.
2) Large frame (>256 bytes) in a page chunk. Allocate an skb, tack it on frags,
post to napi_gro_receive().
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using 4-byte aligned headers is problematic for some architectures.
Since qlge uses 4-byte aligned rx buffers we split headers for these
architectures into a separate buffer and then recopy to align on 2-byte boundary.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_device_detach() does not take the tx_lock, so it's possible that
a call to sky2_xmit_frame is still in progress after
netif_device_detach() is complete.
Take netif_tx_lock() to make sure all transmits have stopped while
we're disabling the devices and that no other CPU is still
transmitting a frame after we've disabling the device.
Proposed fix for "sky2 panic under load" reported by Berck E. Nash.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate code deciding which registers can be accessed out of
sky2_get_regs in preparation for adding more conditions into it.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix ethtool link test for NX3031 chip.
o Remove unused code from phy interrupt callback
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Dump registers such as tx ring and rx ring counter, firmware state,
niu regs, etc. which can be useful for debugging purpose.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx_skbuff is define as:
struct sk_buff *tx_skbuff[TX_RING_ENTRIES];
EVT_RING_ENTRIES is 64 and TX_RING_ENTRIES is 32.
This function is in a error path so that's why it wasn't noticed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
axnet_cs:
remove unnecessary spin_unlock_irqrestore,spin_lock_irqsave.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no break occurred, cnt reaches 0 after the loop.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With `while (--limit > 0)' i reaches 0 after the loop, so upon timeout the
error was not returned.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With `while (--i > 0)' i reaches 0 after the loop, so upon timeout the
error was not issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lp->rx_skb has type struct sk_buff **, not struct sk_buff *, so the
elements of the array should have pointer type, not structure type.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@
x =
<+...sizeof(
- T
+ *x
)...+>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a target login issue, when parent interface is vlan and we are using cxgb3i sepecific
private ip address in '/etc/iscsi/ifaces/' iface file.
Acked-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: Rakesh Ranjan <rakesh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should address the problems in version 1 (lazy) and version 2 (ugly).
Bump the stats on orig_dev not on the newly assigned NULL dev variable.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With `while (i++ < MII_TIMEOUT)' i reaches MII_TIMEOUT + 1 after the loop
This is probably unlikely a problem in practice.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test the just-allocated value for NULL rather than some other value.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,y;
statement S;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
(
if ((x) == NULL) S
|
if (
- y
+ x
== NULL)
S
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code checked slot_rx twice. Check slot_tx by analogy with the bank
case.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E;
@@
(
*E && E
|
*E || E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
velocity_open() calls velocity_give_many_rx_descs(), which gives RX
descriptors to the NIC, before installing an interrupt handler or
calling velocity_init_registers(). I think this is very unsafe and it
appears to explain the bug report <http://bugs.debian.org/508527>.
On MTU change, velocity_give_many_rx_descs() is again called before
velocity_init_registers(). I'm not sure whether this is unsafe but
it does look wrong.
Therefore, move the calls to velocity_give_many_rx_descs() after
request_irq() and velocity_init_registers().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a bond device to specify an arp_ip_target as a host that is
not on the same vlan as the base bond device and still use arp
validation. A configuration like this, now works:
BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3"
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
inet6 fe80::213:21ff:febe:33e9/64 scope link
valid_lft forever preferred_lft forever
9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue
link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff
inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100
inet6 fe80::213:21ff:febe:33e9/64 scope link
valid_lft forever preferred_lft forever
Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: None
Currently Active Slave: eth1
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 1000
ARP IP target/s (n.n.n.n form): 10.0.100.1
Slave Interface: eth1
MII Status: up
Link Failure Count: 1
Permanent HW addr: 00:40:05:30:ff:30
Slave Interface: eth0
MII Status: up
Link Failure Count: 0
Permanent HW addr: 00:13:21:be:33:e9
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use a rather complicated logic to support eTSEC and eTSEC2.0
registers maps in a single driver. Currently, the code tries to
unmap 'regs', but for non-eTSEC2.0 controllers 'regs' doesn't
point to a mapping start, and this might cause badness on probe
failure or module removal:
Freescale PowerQUICC MII Bus: probed
Trying to vfree() nonexistent vm area (e107f000)
------------[ cut here ]------------
Badness at c00a7754 [verbose debug info unavailable]
NIP: c00a7754 LR: c00a7754 CTR: c02231ec
[...]
NIP [c00a7754] __vunmap+0xec/0xf4
LR [c00a7754] __vunmap+0xec/0xf4
Call Trace:
[df827e50] [c00a7754] __vunmap+0xec/0xf4 (unreliable)
[df827e70] [c001519c] iounmap+0x44/0x54
[df827e80] [c028b924] fsl_pq_mdio_probe+0x1cc/0x2fc
[df827eb0] [c02fb9b4] of_platform_device_probe+0x5c/0x84
[df827ed0] [c0229928] really_probe+0x78/0x1a8
[df827ef0] [c0229b20] __driver_attach+0xa4/0xa8
Fix this by introducing a proper priv structure (finally!), which
now holds 'regs' and 'map' fields separately.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes ucc_geth fails to suspend with the following trace:
ucc_geth e0103000.ucc: suspend
ucc_geth e0102000.ucc: suspend
NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at net/sched/sch_generic.c:255
NIP: c021cb5c LR: c021cb5c CTR: c01ab4b4
[...]
NIP [c021cb5c] dev_watchdog+0x298/0x2a8
LR [c021cb5c] dev_watchdog+0x298/0x2a8
Call Trace:
[c0389da0] [c021cb5c] dev_watchdog+0x298/0x2a8 (unreliable)
[c0389e00] [c0031ed8] run_timer_softirq+0x16c/0x1dc
[c0389e50] [c002c638] __do_softirq+0xa4/0x11c
[...]
This patch fixes the issue by properly detaching the device on
suspend, and attaching it back on resume.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hibernation assumes power loss, we should fully reinitialize
PHYs (including platform fixups), as if PHYs were just attached.
This patch factors phy_init_hw() out of phy_attach_direct(), then
converts mdio_bus to dev_pm_ops and adds an appropriate restore()
callback.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes kernel hangs on resume with the following trace:
ucc_geth e0102000.ucc: resume
INFO: task bash:1764 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
bash D 0fecf43c 0 1764 1763 0x00000000
Call Trace:
[cf9a7c10] [c0012868] ret_from_except+0x0/0x14 (unreliable)
--- Exception: cf9a7ce0 at __switch_to+0x4c/0x6c
LR = 0xcf9a7cc0
[cf9a7cd0] [c0008c14] __switch_to+0x4c/0x6c (unreliable)
[cf9a7ce0] [c028bcfc] schedule+0x158/0x260
[cf9a7d10] [c028c720] __mutex_lock_slowpath+0x80/0xd8
[cf9a7d40] [c01cf388] phy_stop+0x20/0x70
[cf9a7d50] [c01d514c] ugeth_resume+0x6c/0x13c
[...]
Here is why.
On suspend:
- PM core starts suspending devices, ucc_geth_suspend gets called;
- ucc_geth calls phy_stop() on suspend. Note that phy_stop() is
mostly asynchronous so it doesn't block ucc_geth's suspend routine,
it just sets PHY_HALTED state and disables PHY's interrupts;
- Suddenly the state machine gets scheduled, it grabs the phydev->lock
mutex and tries to process the PHY_HALTED state, so it calls
phydev->adjust_link(phydev->attached_dev). In ucc_geth case
adjust_link() calls msleep(), which reschedules the code flow back to
PM core, which now finishes suspend and so we end up sleeping with
phydev->lock mutex held.
On resume:
- PM core starts resuming devices (notice that nobody rescheduled
the state machine yet, so the mutex is still held), the core calls
ucc_geth's resume routine;
- ucc_geth_resume restarts the PHY with phy_stop()/phy_start()
sequence, and the phy_*() calls are trying to grab the phydev->lock
mutex. Here comes the deadlock.
This patch fixes the issue by stopping the state machine on suspend
and starting it again on resume.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation instead of
space-separated.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've long lacked a good confirmation that frames
have really gone out, e.g. before going off-channel
for a scan. Add a flush() operation that drivers
can implement to provide that confirmation, and use
it in a few places:
* before scanning sends the nullfunc frames
* after scanning sends the nullfunc frames, if any
* when going idle, to send any pending frames
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is checked in add_interface, but there it is easily replaced with
a check of priv->vif. If that information should become necessary,
it is available in vif->type anyway.
It is also checked in led_turn_on and led_turn_off, where I made the
substitutions as described above. Of course, these checks seem to
have been incorrect since the driver was using NL80211_IFTYPE_MONITOR
to indicate no interface rather than NL80211_IFTYPE_UNSPECIFIED.
Anyway, I think these checks may be extraneous...?
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is only checked in add_interface, and there it is easily replaced
with a check of priv->vif. If that information should become necessary,
it is available in vif->type anyway.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let each of them take a struct rt2x00_dev pointer as argument instead of
a mixture of struct rt2x00_chip and struct rt2x00_dev pointers.
Preparation for further clean ups in the rt2x00 chip handling, especially
for rt2800 devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need for Kconfig symbols RT2800PCI_PCI and RT2800PCI_SOC to be
tristates, as they are only used to check whether RT2800 PCI or SOC support
is to be compiled in.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800lib currently checks whether RT2800USB is enabled in the configuration.
Strictly speaking this is not necessary, it only needs to know whether the
generic rt2x00usb library functions are available. Therefore check for
RT2X00_LIB_USB instead.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix checking for SOC support in rt2800pci. The wrong config (an unexisting
one) was checked.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a minor bug in the code causing a "join" to be performed before
there is an intention to associate. Fix this.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because the interface is started and the vif are created and destroyed
separately, there is a slim possibility beacon-loss indications occur while
there is no vif - causing a kernel-oops unless checked.
Add checking for the vif.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This acx configures host clock parameters in correspondence with the clock
request line - the settling time of the clock, and whether fast wake-up is
supported.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For cleaner implementation, change the bunch of booleans in the struct wl1271
structure into a flags bitmask.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, only basic rates were used for data transmission - resulting in
reduced transfer rates. This patch takes enables the firmware to take advantage
of the full set of data rates supported by the AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously a "firmware chooses" value was used for the rates of all control
message templates set to the firmware. This resulted in a too high rate to be
chosen to transmit those messages. Change this by configuring a fixed low rate
for the templates.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds rudimentary a-hoc support for the driver. It will allow
setting up ad-hoc, and for other devices to scan and join. The beacon and probe
response template setting is slightly dirty, and need to be properly
implemented with support from mac80211. Also, the SSID is not configured to the
firmware - the FW will not be able to respond to probe requests autonomously.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the beacon-loss indication to stack from PSM entry failure handling -
this will cause more problems than it will solve due to the design of the
mac80211.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a short delay before powering on the wl1271. Normally, it is
not needed, but if the wl1271 has been powered off shortly before, for reliable
firmware-booting this small stabilization delay is required.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 has a hardware bug which causes it to randomly (very infrequently)
to fail powering up properly. This patch implements retry for the chipset boot
sequence, to work around the hardware problem.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 sometimes requests power save entry while not associated - this
will cause problems, so prevent it if not associated. Go to powersave once
association is complete.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In reference source, events are acknowledged separately - fix the driver to
do the same.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While not associated, default the data rates to 1 and 2mbps, so that only
those rates will be used for association related message transfer. Once
associated, configure the full rate-set supported by the AP.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the smart-reflex ACX - the associated parameters are now configured
in the radio parameters config.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure correct values to be used with the smart-reflex configuration of the
firmware.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the data path configuration, one of the parameters is the channel. We
have been setting it to wl->channel, which is not correct in this case. This
channel has nothing to do with the channel we're currently tuned to, since it
is only used for calibration during this phase. Hardcoded the channel to 1,
according to the reference driver.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the new reference driver, some of the firmware configuration values have
been changed. This patch changes them in the wl1271 driver accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were uploading the whole NVS file, but that is wrong, because the same
file also contains the initialization values. For the latest firmwares, we
should upload only the initial 468 bytes from the file.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some debugging tools require the chip to be powered on before they can work.
With these tools, we shouldn't upload the firmware nor boot the firmware
ourselves, so this debufs file is provided. It always contains the gpio
power setting (0 = off, 1 = on). To change the power setting, just write 0
or 1 to the file.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a typo in one of the values in the rx_rssi_and_proc_compens elemt
of the Radio Parameters struct.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer firmwares require the dco itrim parameters to be set during
initialization. This patch implements the new ACX function and calls it.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were using CONF_TX_RATE_MASK_ALL when calling wl1271_acx_rate_policies()
during init. We should use WL1271_DEFAULT_BASIC_RATE_SET instead. The
values are the same, but the latter is just the correct macro to use.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The call to wl1271_cmd_build_null_data() was missing when we got associated,
this was causing PS to fail. This patch adds the call and now PS seems to
work.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were not checking the return value from the call to wl1271_cmd_join().
Added a check to make things more reliable.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 firmware supports maximun 25.5dBm, so the driver was returning
-EINVALID to anything above that. This patch uses the channel max_power
option to limit the TX power to 25dBm.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now we're using a the idle information coming from mac80211 to decide when to
disconnect. If we have joined (ie. we're listening to a channel), whenever
the interface goes to idle, we will issue a disconnect command. So the
workaround to send a disconnect command before joining is not needed anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we need to change the channel before association, we have to send a join
command with a valid BSSID. With this patch we use 0baddeadbeef as the
BSSID. There are ongoing discussions with TI to get this done in a cleaner
way.
When we go back to idle, we issue a CMD_DISCONNECT to make sure the firmware
stops listening to the channel and cleans things up internally.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new radio parameters for new structures based on firmware revision
6.1.0.0.288.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were some changes in the values we have to use for these settings. This
patches updates them.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In revision 6.1.0.0.288 the general parameters structure has changed. This
patch updates the driver code accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In revision 6.1.0.0.288 the radio parameters structure has changed. This
patch updates the driver code accordingly.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If userencounter the "Fatal DMA Problem" with a BCM43XX device, and
still wish to use b43 as the driver, their only option is to rebuild
the kernel with CONFIG_B43_FORCE_PIO. This patch removes this option and
allows PIO mode to be selected with a load-time parameter for the module.
Note that the configuration variable CONFIG_B43_PIO is also removed.
Once the DMA problem with the BCM4312 devices is solved, this patch will
likely be reverted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The receive descriptor ops that are currently marked as being for
8687 only are actually used for all STA firmware images, whereas the
receive descriptor ops marked as 8366 are only used on 8366 when an
AP firmware image is in use.
Rename the receive descriptor ops to reflect this, use the STA ops
unconditionally if the firmware image loaded reported the STA ready
code, and rename the mwl8k_device_info::rxd_ops member to ap_rxd_ops
to indicate that it should only be used if we are running on AP
firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whether the firmware we have loaded is AP or STA firmware decides
which receive descriptor format we have to use. Therefore, move
rx/tx ring initialisation to be after firmware loading.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sort firmware commands by command code, get rid of the 802_11 substring
in all command names, and make sure that the command functions match the
firmware command names.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allocate priv->rx_packets[IWM_RX_ID_HASH + 1] because the max array
index is IWM_RX_ID_HASH according to IWM_RX_ID_GET_HASH().
Cc: stable@kernel.org
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
`loop' reaches INIT_LOOP + 1 after the loop. so if ACX_INTR_INIT_COMPLETE
occurs in the last iteration the write occurs but also the error out as if a
timeout occurred. This is probably very unlikely to ever occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous change added in:
commit 815833e7ec
ath9k: fix tx status reporting
was not checking all possible tx error conditions. This could possibly
lead to throughput issues due to slow rate control adaption or missed
retransmissions of failed A-MPDU frames.
This patch adds a mask for all possible error conditions and uses it
in the xmit ok check.
Cc: stable@kernel.org
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AMDPDU actions poke hardware for TX operation, as such
we want to turn hardware on for these actions. AMDPU RX operations
do not require hardware on as nothing is done in hardware for
those actions. Without this we cannot guarantee hardware has
been programmed correctly for each AMPDU TX action.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove a IBSS/AP/Mesh interface we stop DMA
but to do this we should ensure hardware is on. Awaken
the device prior to these calls. This should ensure
DMA is stopped upon suspend and plain device removal.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure the device is awake prior to trying to tell hardware
to stop it. Impact of not doing this is we can likely leave
the device in an undefined state likely causing issues with
suspend and resume. This patch ensures harware is where it
should be prior to suspend.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is just a clean up and doesn't make a functional difference. It keeps the
lint checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the remaining users of the rx status
'qual' field and the field itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a rt2870 based device.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calibration period is now invoked by triggering a software
interrupt from within the ISR by ath5k_hw_calibration_poll()
instead of via a timer.
However, the calibration interval isn't initialized before
interrupts are enabled, so we can have a situation where an
interrupt occurs before the interval is assigned, so the
interval is actually negative. As a result, the ISR will
arm a software interrupt to schedule the tasklet, and then
rearm it when the SWI is processed, and so on, leading to a
softlockup at modprobe time.
Move the initialization order around so the calibration interval
is set before interrupts are active. Another possible fix
is to schedule the tasklet directly from the poll routine,
but I think there are additional plans for the SWI.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason to signal a carrier off when doing a 802.11 scan.
Cc: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using dev_hard_header allows us to use LLC with VLANs and potentially
other Ethernet/TokernRing specific encapsulations. It also removes code
duplication between LLC and Ethernet/TokenRing core code.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few lines earlier we assume that best->slave could be either null or non-null so
we should check it here as well.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f001fde5ea changed
net_device.dev_addr from a 32-byte array to a pointer.
I found 4 ethernet drivers which rely on sizeof(dev_addr), which are now
only copying 4 bytes of the address information on 32bit systems.
Fix them to use ETH_ALEN.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfar_select_queue() function was used to set queue mapping
only for forwarding/bridging applications and the condition
for locally generated packets was completely ignored.
The solution is to remove the gfar_select_queue() function and
use skb_record_rx_queue to set queue mapping for
forwarding/bridging applications. This will ensure that in case of
forwarding/bridging applications txq = rxq will be selected and
skb_tx_hash will be used to pick up a txq for locally generated packets.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using macro tun_sk is more clear and shorter. However tun.c has tun_sk,
but doesn't use it.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If PHY doesn't have an IRQ, phylib would poll for link changes, and
would call adjust_link() every second. In that case we disable and
enable the controller every second.
Let's better check if there is actually anything changed, and, if so,
change the MAC settings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 864fdf884e ("ucc_geth:
Fix hangs after switching from full to half duplex") ucc_geth driver
disables the controller during MAC configuration changes. Though,
disabling the controller might take quite awhile, and so the netdev
watchdog might get upset:
NETDEV WATCHDOG: eth2 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at c02729a8 [verbose debug info unavailable]
NIP: c02729a8 LR: c02729a8 CTR: c01b6088
REGS: c0451c40 TRAP: 0700 Not tainted (2.6.32-trunk-8360e)
[...]
NIP [c02729a8] dev_watchdog+0x280/0x290
LR [c02729a8] dev_watchdog+0x280/0x290
Call Trace:
[c0451cf0] [c02729a8] dev_watchdog+0x280/0x290 (unreliable)
[c0451d50] [c00377c4] run_timer_softirq+0x164/0x224
[c0451da0] [c0032a38] __do_softirq+0xb8/0x13c
[c0451df0] [c00065cc] do_softirq+0xa0/0xac
[c0451e00] [c003280c] irq_exit+0x7c/0x9c
[c0451e10] [c00640c4] __ipipe_sync_stage+0x248/0x24c
[...]
This patch fixes the issue by detaching the netdev during the
time we change the configuration.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>
Following oops was seen with the ucc_geth driver:
Unable to handle kernel paging request for data at address 0x00000058
Faulting instruction address: 0xc024f2fc
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c024f2fc] skb_recycle_check+0x14/0x100
LR [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
Call Trace:
[df857d50] [c000b03c] __ipipe_grab_irq+0x3c/0xa4 (unreliable)
[df857d60] [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
[df857dd0] [c0258cf8] net_rx_action+0xf8/0x1b8
[df857e10] [c0032a38] __do_softirq+0xb8/0x13c
[df857e60] [c00065cc] do_softirq+0xa0/0xac
[...]
This is because ucc_geth_tx() tries to process an empty queue when
queues are logically stopped. Stopping the queues doesn't disable
polling, and since nowadays ucc_geth_tx() is actually called from
the polling routine, the oops above might pop up.
Fix this by removing 'netif_queue_stopped() == 0' check.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is reset during MTU change, ring size change, or self
test, etc, the cnic status block needs to be properly initialized if
cnic is registered.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are BUGs "scheduling while atomic" triggered by the timer
rhine_tx_timeout(). They are caused by calling napi_disable() (with
msleep()). This patch fixes it by moving most of the timer content to
the workqueue function (similarly to other drivers, like tg3), with
spin_lock() changed to BH version.
Additionally, there is spin_lock_irq() moved in rhine_close() to
exclude napi_disable() etc., also tg3's way.
Reported-by: Andrey Rahmatullin <wrar@altlinux.org>
Tested-by: Andrey Rahmatullin <wrar@altlinux.org>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a pci_save_state() call in ixgbe_resume() after
pci_restore_state(). A similar change was made in ixgbe_io_slot_reset()
that accommodates pci_restore_state() new behavior. This change makes
pci_restore_state() clear the saved_state flag This is necessary due
to a resent kernel change to pci_restore_state() so that it now clears
the saved_state flag of the device right after the device.s standard
configuration registers have been poplulated with the previously saved
values.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some misc changes to cleanup whitespace issues and fix/remove some #define
HW defintions.
1) fix some whitespace issues
2) more verbose err msg when resources aren't available to configure vnic
3) remove unused #define
4) fix RSS #define rss hash types
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only rx_usec and tx_usec options for ethtool -C are settable as those
are the only settings that make sense to HW. Adds driver reporting of
intr coalescing timer value in usec units rather than HW units.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous driver was aligning ring sizes to 16 descs, but hardware actually
wants desc ring sizes to be aligned to 32 descs.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In set_multicast(), only push pkt filter changes down to firmware if
pkt filter actually changes.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During dev->open(), make sure we get at least one skb on the Rx ring.
Otherwise abort the interface load. Also, if we get skb allocation
failures in NAPI poll while trying to replenish the ring, try again
later so we don't end up starving out the Rx ring completely.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dev->stop shutdown bug where driver was stopping xmit queue and then
disabling intrs. Fix is to disable intrs first and then stop the xmit
queue, otherwise an interrupt could cause the queue to be rewoken. Also,
no need to explicitly do queue servicing because queues are cleaned and
reset back to initial state at end of dev->stop. Servicing queues also
had the side-effect of also rewakening the xmit queue, which is not what
we want.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to return correct values for transceiver and supported in
ethtool get_settings function.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC controller has to be set to an appropriate mode before doing a loopback
test. Test will fail otherwise.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change ensures that loopback test command gives up after 4 seconds when
the hardware is not responsive. This could happen if the ports are connected
properly in loopback mode.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool code for enabling Wake on Lan was not correctly checking the
status register bits so as a result ports 0 and 2 were both being allowed
to set WOL to enabled even though it is only supported on the first port
for our adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The watermark values for the 82575 were not being set correctly. As a
result the high and low watermark values were set to the same value which
can lead to excess xon/xoff packets being generated.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change resolves an issue seen in some configurations where the link
may drop to 100Mb/s even though the link itself supports 1000Mb/s. The
issue was root caused to the fact that we were only trying the link once.
Now instead we will try up to 5 attempts on a faulty cable before
downshifting to 100Mb/s.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were forcing the PCS link up in error when we are in KX mode. We should
only be disabling autoneg, not forcing the link up.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hardware watchdog can misfire, so it does more harm than good.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some cables have EEPROMs that conflict with the PHY's on-board EEPROM
so it cannot load firmware.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY's firmware very occasionally appears to lock up very early, but
with the heartbeat update still running. Rebooting the microcontroller
core seems to be sufficient to recover.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY boots in a mode which is not necessarily optimal. This change
switches it to self-configure mode (except when in loopback, which
won't work in that mode if an SFP+ module is not present) by rebooting
the PHY's microcontroller, and replicating the sequence of configuration
writes from the boot EEPROM with the appropriate changes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we see the PHY remaining stuck in a link-down state due to PCS being
down while PMA/PMD is up, we briefly switch to PMA/PMD loopback and back,
which usually unsticks it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need buffer->len to remain valid to work out the correct address to
be unmapped. We therefore need to clear buffer->len after the unmap
operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The XGXS block may not get a link immediately in XGXS or XAUI loopback
modes, so we still need to check it. Split falcon_xaui_link_ok() into
falcon_xgxs_link_ok(), which checks only the Falcon XGXS block, and
falcon_xmac_link_ok(), which checks one or both sides of the link as
appropriate. Also rename falcon_check_xaui_link() to
falcon_xmac_link_ok_retry().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prevents efx->link_advertising from being blatted during
a reset.
The phy_short_reach sysfs node is now destroyed later in the
port shutdown process, so check for STATE_RUNNING after
acquiring the rtnl_lock (just like in set_phy_flash_cfg).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. remove address argument since we use same address IWMC_SDIO_DATA_ADDR in
all cases
2. add __iwmct_tx - non locking tx function for already locked contexts
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. add TRACE level
2. use TRACE where needed to reduce the noise
3 don't INFOEX from driver
4. add DUMP level for packets dumps
5. use correct context for the log messages
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. removed redundant NULL-pointers checks in iwmct_fw_load
as release_firmware and kfree are NULL pointer friendly
2. remove redundant memset of the parser since the structure
is fully initialized in iwmct_fw_parser_init function
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>