eee_get_cur assumes that the output data is already zeroed. It can
read-modify-write the advertised field:
if (ipcnfg & E1000_IPCNFG_EEE_100M_AN)
2594 edata->advertised |= ADVERTISED_100baseT_Full;
This is ok for the normal ethtool eee_get call, which always
zeroes the input data before.
But eee_set_cur also calls eee_get_cur and it did not zero the input
field. Later on it then compares agsinst the field, which can contain partial
stack garbage.
Zero the input field in eee_set_cur() too.
Cc: jeffrey.t.kirsher@intel.com
Cc: netdev@vger.kernel.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highbank and Midway xgmac h/w have different number of MAC address filter
registers with 7 and 31, respectively. Highbank has been wrong, so fix it
and detect the number of filter registers at run-time. Unfortunately,
the version register is the same on both SOCs, so simply test if write to
the last filter register will take a value. It always reads as 0 if not.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even in promiscuous mode, we need to add filter addresses for correct
operation. This fixes silent failures when using a bridge and adding
addresses using the "bridge fdb add" command.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 2ee68f621a (net: calxedaxgmac: fix various errors in
xgmac_set_rx_mode), a fix to clean-up old address entries was added.
However, the loop to zero out the entries failed to increment the register
address resulting in only 1 entry getting cleared. Fix this to correctly
use the loop index. Also, the end of the loop condition was off by 1 and
should have been <= rather than <.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RFKill cuts short a scan, mac80211 cancels the scan.
This is done by sending a host command to the firmware, but
this command was dropped because of RFKill. Flag this
command as "SEND_IN_RFKILL" to make sure it is sent to the
firmware. The firmware will send SCAN_COMPLETE_NOTIFICATION
which will trigger a call to ieee80211_scan_completed.
If the scan cannot be aborted, it is because the firmware
already finished the scan but we hadn't notified mac80211
at the time mac80211 decided to cancel the scan. By the time
we see the scan could not be aborted, mac80211 has been
notified already.
This patch fixes situations in which we didn't notify
mac80211 upon completion of the scan that was cut short
by RFkill.
Cc: stable@vger.kernel.org [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add some new PCI IDs to the table for 6000, 6005 and 6235 series.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This triggers automatic bug reports and add no valuable
information. Print a simple error instead and drop the
host command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add some new PCI IDs to the table for 7000 & 3160 series
Cc: stable@vger.kernel.org
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A few NICs can get into trouble if we reset the TX queue
counters in certain very rare situation. To be on the safe
side, simply avoid to reset the TX queue counter.
This is relevant for non-AMPDU queues only since on AMPDU
we have no choice - we must start the TX queue at the right
index.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The D3 firmware image doesn't support uAPSD, so disable it.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Guy Cohen <guy.cohen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
o Interface needs to be brought down and up while configuring SR-IOV.
Protect interface up/down using rtnl_lock()/rtnl_unlock()
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma descriptors indexes are only initialized on the probe function.
If a packet is on the buffer when temac_stop is called, the dma
descriptors indexes can be left on a incorrect state where no other
package can be sent.
So an interface could be left in an usable state after ifdow/ifup.
This patch makes sure that the descriptors indexes are in a proper
status when the device is open.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__initdata tag should be placed between the variable name and equal
sign for the variable to be placed in the intended .init.data section.
In this particular case __initdata is incorrect as moxart_mac_driver
can be used after the driver gets initialized.
Also while at it static-ize moxart_mac_driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.
For instance:
fsl,cksel = <0>;
for using external (TSEC_TMR_CLK input) high precision timer
reference clock.
Other acceptable values:
<1> : eTSEC system clock
<2> : eTSEC1 transmit clock
<3> : RTC clock input
When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 894116bd0e.
I applied the wrong version of this patch, correct
version coming up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently grabbed this report:
https://bugzilla.redhat.com/show_bug.cgi?id=1005567
Of an issue in which the bonding driver, with an attached vlan encountered the
following errors when bond0 was taken down and back up:
dummy1: promiscuity touches roof, set promiscuity failed. promiscuity feature of
device might be broken.
The error occurs because, during __bond_release_one, if we release our last
slave, we take on a random mac address and issue a NETDEV_CHANGEADDR
notification. With an attached vlan, the vlan may see that the vlan and bond
mac address were in sync, but no longer are. This triggers a call to dev_uc_add
and dev_set_rx_mode, which enables IFF_PROMISC on the bond device. Then, when
we complete __bond_release_one, we use the current state of the bond flags to
determine if we should decrement the promiscuity of the releasing slave. But
since the bond changed promiscuity state during the release operation, we
incorrectly decrement the slave promisc count when it wasn't in promiscuous mode
to begin with, causing the above error
Fix is pretty simple, just cache the bonding flags at the start of the function
and use those when determining the need to set promiscuity.
This is also needed for the ALLMULTI flag
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Mark Wu <wudxw@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: Mark Wu <wudxw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass-all-multicast is controlled by bit 3 in RX control, not bit 2
(pass undersized frames).
Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet is passed from mac80211 to the driver with the
IEEE80211_TX_CTL_PS_RESPONSE flag set, it bypasses the normal driver
internal queueing and goes directly to the UAPSD queue.
When that happens, packets that are part of a BlockAck session still
need to be tracked as such inside the driver, otherwise it will create
discrepancies in the receiver BA reorder window, causing traffic stalls.
This only happens in AP mode with powersave-enabled clients.
This patch fixes the regression introduced in the commit
"ath9k: use software queues for un-aggregated data packets"
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
601216e "mwifiex: process RX packets in SDIO IRQ thread directly"
introduced a command timeout issue which can be reproduced easily on
an AM33xx platform using a test application written by Daniel Mack:
https://gist.github.com/zonque/6579314
mwifiex_main_process() is called from both the SDIO handler and
the workqueue. In case an interrupt occurs right after the
int_status check, but before updating the mwifiex_processing flag,
this interrupt gets lost, resulting in a command timeout and
consequently a card reset.
Let main_proc_lock protect both int_status and mwifiex_processing
flag. This fixes the interrupt lost issue.
Cc: <stable@vger.kernel.org> # 3.7+
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 9483f40d8d.
Some devices stop to connect with above commit, see:
https://bugzilla.kernel.org/show_bug.cgi?id=61621
Since there is no clear benefit of having MSI enabled, just revert
change to fix the problem.
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the frontend state changes netback now specifies its desired state to
a new function, set_backend_state(), which transitions through any
necessary intermediate states.
This fixes an issue observed with some old Windows frontend drivers where
they failed to transition through the Closing state and netback would not
behave correctly.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cinterion PLXX LTE devices have a 0x0060 product ID, not 0x12d1.
The blacklisting in the serial/option driver does actually use the correct PID,
as per commit 8ff10bdb14 ('USB: Blacklisted
Cinterion's PLxx WWAN Interface').
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
Signed-off-by: Aleksander Morgado <aleksander@lanedo.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently IEEE 1588 timer reference clock source is determined through
hard-coded value in gianfar_ptp driver. This patch allows to select ptp
clock source by means of device tree file node.
For instance:
fsl,cksel = <0>;
for using external (TSEC_TMR_CLK input) high precision timer
reference clock.
Other acceptable values:
<1> : eTSEC system clock
<2> : eTSEC1 transmit clock
<3> : RTC clock input
When this attribute isn't used, eTSEC system clock will serve as
IEEE 1588 timer reference clock.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of RCU api makes vxlan code easier to understand. It also
fixes bug due to missing ACCESS_ONCE() on sk_user_data dereference.
In rare case without ACCESS_ONCE() compiler might omit vs on
sk_user_data dereference.
Compiler can use vs as alias for sk->sk_user_data, resulting in
multiple sk_user_data dereference in rcu read context which
could change.
CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the flexcan_chip_start() function first the flexcan core is going through
the soft reset sequence, then the RX FIFO is enabled.
With the hardware is put into FIFO mode, message buffers 1...7 are reserved by
the FIFO engine. The remaining message buffers are in reset default values.
This patch removes the bogus initialization of the message buffers, as it
causes an imprecise external abort on imx6.
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Commit 638c5115a7949(USBNET: support DMA SG) introduces DMA SG
if the usb host controller is capable of building packet from
discontinuous buffers, but missed handling padding packet when
building DMA SG.
This patch attachs the pre-allocated padding packet at the
end of the sg list, so padding packet can be sent to device
if drivers require that.
Reported-by: David Laight <David.Laight@aculab.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Commit 7e2cf4feba
("qlcnic: change driver hardware interface mechanism")
has overwritten
commit b43e5ee76a
("qlcnic: Register device in FAILED state")
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN priority is not being displayed for a VF currently when user executes
"ip link show" command. This patch fixes it.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thix fix allows the VLAN priority to be configured for a VF interface
via the "ip link set DEVICE vf NUM" path.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the VF interfaces have privilege to add VLANs.
Allow VLANs to be configured on these interfaces.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In BE3-R, when UMC is enabled, the number of VLANs that can be added
to the interface is reduced to 15.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface runs out of the allocated entries in VLAN table,
we program the interface in VLAN promiscuous mode.
Use OPCODE_COMMON_NTWK_RX_FILTER to set VLAN Promiscuous mode
instead of OPCODE_COMMON_NTWK_VLAN_CONFIG.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Size of be_nic_res_desc structure is incorrect. Fix it.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx on SH-R can lockup if the packet size is less than 32 bytes.
Pad such packets to a safer 36-byte size.
Patch uses the Lancer-R workaround - which checks for packet <= 32-bytes
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Regarding the Bluetooth bits, Gustavo says:
"First Bluetooth fixes to 3.12, it includes:
* 3 patches to add device id for 3 new hardwares.
* 2 patches from Johan to fix the rfkill behaviour during setup stage
* a small clean up in the rfcomm TTY code that fixes a potential racy
condition (by Gianluca Anzolin)
* 2 fixes to proper set encryption key size and security level in the
peripheral role of Bluetooth LE devices. (by Andre Guedes)
* a fix for dealing devices where pairing is not necessary, we were keeping
the Bluetooth ACL connection alive for too much time. (by Syam Sidhardhan)"
Also, I fixed-up an curly-brace indentation problem in the Bluetooth
code while merging. On top of that...
Alexey Khoroshilov brings a p54usb fix to avoid a resource leak when
request_firmware_nowait fails.
Amitkumar Karwar fixes a firmware hang caused by too much header data
being appended for USB devices using the mwifiex driver.
Arend van Spriel provides three fixes: a brcmfmac fix to relocate some
driver code outside of an .init section; a scheduling while atomic
fix for bcma; and, another scheduling while atomic fix for brcmsmac.
Bing Zhao offers a pair of mwifiex fixes: a code change to avoid
firmware timeouts on USB; and a fix for a NULL pointer dereference.
Christian Lamparter adds a device ID to p54usb.
Felix Fietkau implements a quartet of small ath9k fixes, including
a locking fix, a list management fix, a fix to properly mark a stale
buffer, and an aggregate buffering fix.
Larry Finger champions a data alignment fix to make rtlwifi work
better with ARM builds.
Solomon Peachy reverts an earlier interrupt handling fix for cw1200
and replaces it with a new threaded oneshot irq handler implementation.
Sujith Manoharan fixes an ath9k regression by reverting an earlier
patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
coccicheck shows:
drivers/net/ethernet/intel/i40e/i40e_adminq.c:704:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:763:1-7: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_adminq.c:810:2-8: Replace memcpy
with struct assignment
drivers/net/ethernet/intel/i40e/i40e_common.c:510:2-8: Replace memcpy
with struct assignment
Fix each of them with a *a = *b;
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches, clean up return values in some functions
making sure to have consistent return types, not mixing types.
A couple of Joe's comments suggested returning void, but since
the functions in question are ndo defined, the return values are fixed.
So make a comment in the header that notes this is a function called by
net_device_ops.
v2: fix post increment bug in return
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When calling admin queue functions the driver should use aq_ret
variable to help make clear that the return value is not a regular
return variable.
This allows for clean up of the return types that were previously
converted to int.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches clean up a loop flow.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As mentioned by Joe Perches, we should be using
foo = alloc(...)
if (!foo)
return -ENOMEM;
return 0;
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Joe Perches <joe@perches.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add back 82580 loopback tests to ethtool.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
sysfs ns (namespace) implementation became more convoluted than
necessary while trying to hide ns information from visible interface.
The relatively recent attr ns support is a good example.
* attr ns tag is determined by sysfs_ops->namespace() callback while
dir tag is determined by kobj_type->namespace(). The placement is
arbitrary.
* Instead of performing operations with explicit ns tag, the namespace
callback is routed through sysfs_attr_ns(), sysfs_ops->namespace(),
class_attr_namespace(), class_attr->namespace(). It's not simpler
in any sense. The only thing this convolution does is traversing
the whole stack backwards.
The namespace callbacks are unncessary because the operations involved
are inherently synchronous. The information can be provided in in
straight-forward top-down direction and reversing that direction is
unnecessary and against basic design principles.
This backward interface is unnecessarily convoluted and hinders
properly separating out sysfs from driver model / kobject for proper
layering. This patch updates attr ns support such that
* sysfs_ops->namespace() and class_attr->namespace() are dropped.
* sysfs_{create|remove}_file_ns(), which take explicit @ns param, are
added and sysfs_{create|remove}_file() are now simple wrappers
around the ns aware functions.
* ns handling is dropped from sysfs_chmod_file(). Nobody uses it at
this point. sysfs_chmod_file_ns() can be added later if necessary.
* Explicit @ns is propagated through class_{create|remove}_file_ns()
and netdev_class_{create|remove}_file_ns().
* driver/net/bonding which is currently the only user of attr
namespace is updated to use netdev_class_{create|remove}_file_ns()
with @bh->net as the ns tag instead of using the namespace callback.
This patch should be an equivalent conversion without any functional
difference. It makes the code easier to follow, reduces lines of code
a bit and helps proper separation and layering.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Outgoing packets sent by via-rhine have their VLAN PCP field off by one
(when hardware acceleration is enabled). The TX descriptor expects only VID
and PCP (without a CFI/DEI bit).
Peter Boström noticed and reported the bug.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Cc: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses platform_driver_probe() to obtain platform data
if any. However, that function is placed in the .init section so
it must be called upon driver module initialization.
The problem was reported by Fenguang Wu resulting in a kernel
oops because the .init section was already freed.
[ 48.966342] Switched to clocksource tsc
[ 48.970002] kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
[ 48.970851] BUG: unable to handle kernel paging request at ffffffff82196446
[ 48.970957] IP: [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] PGD 1e76067 PUD 1e77063 PMD f388063 PTE 8000000002196163
[ 48.970957] Oops: 0011 [#1]
[ 48.970957] CPU: 0 PID: 17 Comm: kworker/0:1 Not tainted 3.11.0-rc7-00444-gc52dd7f #23
[ 48.970957] Workqueue: events brcmf_driver_init
[ 48.970957] task: ffff8800001d2000 ti: ffff8800001d4000 task.ti: ffff8800001d4000
[ 48.970957] RIP: 0010:[<ffffffff82196446>] [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] RSP: 0000:ffff8800001d5d40 EFLAGS: 00000286
[ 48.970957] RAX: 0000000000000001 RBX: ffffffff820c5620 RCX: 0000000000000000
[ 48.970957] RDX: 0000000000000001 RSI: ffffffff816f7380 RDI: ffffffff820c56c0
[ 48.970957] RBP: ffff8800001d5d50 R08: ffff8800001d2508 R09: 0000000000000002
[ 48.970957] R10: 0000000000000000 R11: 0001f7ce298c5620 R12: ffff8800001c76b0
[ 48.970957] R13: ffffffff81e91d40 R14: 0000000000000000 R15: ffff88000e0ce300
[ 48.970957] FS: 0000000000000000(0000) GS:ffffffff81e84000(0000) knlGS:0000000000000000
[ 48.970957] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 48.970957] CR2: ffffffff82196446 CR3: 0000000001e75000 CR4: 00000000000006b0
[ 48.970957] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 48.970957] DR3: 0000000000000000 DR6: 0000000000000000 DR7: 0000000000000000
[ 48.970957] Stack:
[ 48.970957] ffffffff816f7df8 ffffffff820c5620 ffff8800001d5d60 ffffffff816eeec9
[ 48.970957] ffff8800001d5de0 ffffffff81073dc5 ffffffff81073d68 ffff8800001d5db8
[ 48.970957] 0000000000000086 ffffffff820c5620 ffffffff824f7fd0 0000000000000000
[ 48.970957] Call Trace:
[ 48.970957] [<ffffffff816f7df8>] ? brcmf_sdio_init+0x18/0x70
[ 48.970957] [<ffffffff816eeec9>] brcmf_driver_init+0x9/0x10
[ 48.970957] [<ffffffff81073dc5>] process_one_work+0x1d5/0x480
[ 48.970957] [<ffffffff81073d68>] ? process_one_work+0x178/0x480
[ 48.970957] [<ffffffff81074188>] worker_thread+0x118/0x3a0
[ 48.970957] [<ffffffff81074070>] ? process_one_work+0x480/0x480
[ 48.970957] [<ffffffff8107aa17>] kthread+0xe7/0xf0
[ 48.970957] [<ffffffff810829f7>] ? finish_task_switch.constprop.57+0x37/0xd0
[ 48.970957] [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[ 48.970957] [<ffffffff81a6923a>] ret_from_fork+0x7a/0xb0
[ 48.970957] [<ffffffff8107a930>] ? __kthread_parkme+0x80/0x80
[ 48.970957] Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
[ 48.970957] RIP [<ffffffff82196446>] classes_init+0x26/0x26
[ 48.970957] RSP <ffff8800001d5d40>
[ 48.970957] CR2: ffffffff82196446
[ 48.970957] ---[ end trace 62980817cd525f14 ]---
Cc: <stable@vger.kernel.org> # 3.10.x, 3.11.x
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815
[ 2.883807] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000048
[ 2.883813] IP: [<ffffffff815a65e0>] pfifo_fast_enqueue+0x90/0x90
[ 2.883834] CPU: 1 PID: 3220 Comm: kworker/u8:90 Not tainted
3.11.1-monotone-l0 #6
[ 2.883834] Hardware name: Microsoft Corporation Surface with
Windows 8 Pro/Surface with Windows 8 Pro,
BIOS 1.03.0450 03/29/2013
On Surface Pro, suspend to ram gives a NULL pointer dereference in
pfifo_fast_enqueue(). The stack trace reveals that the offending
call is clearing carrier in mwifiex_usb suspend handler.
Since commit 1499d9f "mwifiex: don't drop carrier flag over suspend"
has removed the carrier flag handling over suspend/resume in SDIO
and PCIe drivers, I'm removing it in USB driver too. This also fixes
the bug for Surface Pro.
Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: Dmitry Khromov <icechrome@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug 60815 - Interface hangs in mwifiex_usb
https://bugzilla.kernel.org/show_bug.cgi?id=60815
We have 4 bytes of interface header for packets delivered to SDIO
and PCIe, but not for USB interface.
In Tx AMSDU case, currently 4 bytes of garbage data is unnecessarily
appended for USB packets. This sometimes leads to a firmware hang,
because it may not interpret the data packet correctly.
Problem is fixed by removing this redundant headroom for USB.
Cc: <stable@vger.kernel.org> # 3.5+
Tested-by: Dmitry Khromov <icechrome@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added USB ID for Corega WLUSB2GTST USB adapter.
Cc: <stable@vger.kernel.org>
Reported-by: Joerg Kalisch <the_force@gmx.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This supercedes the older patch ("cw1200: Don't perform SPI transfers in
interrupt context") that badly attempted to fix this problem.
This is a far simpler solution, which has the added benefit of
actually working.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit aec8e88c94.
This solution turned out to cause interrupt delivery problems, and
rather than trying to fix this approach, it has been scrapped in favor
of an alternative (and far simpler) implementation.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For pcie8897, the hs_cfg cancel command (0xe5) times out when host
comes out of suspend. This is caused by an incompleted host sleep
handshake between driver and firmware.
Like SDIO interface, PCIe also needs to go through firmware power
save events to complete the handshake for host sleep configuration.
Only USB interface doesn't require power save events for hs_cfg.
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The private array at the end of the rtl_priv struct is not aligned.
On ARM architecture, this causes an alignment trap and is fixed by aligning
that array with __align(sizeof(void *)). That should properly align that
space according to the requirements of all architectures.
Reported-by: Jason Andrews <jasona@cadence.com>
Tested-by: Jason Andrews <jasona@cadence.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevents race conditions when un-aggregated frames are pending in the
driver.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If request_firmware_nowait() fails in p54u_load_firmware(),
p54u_load_firmware_cb is not called and no one decrements usb_dev refcnt.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When .release_buffered_frames was implemented, only A-MPDU packets were
buffered internally. Now that this has changed, the BUF_AMPDU flag needs
to be checked before calling ath_tx_addto_baw
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Optimize LNA check" tried
to use the "rs_firstaggr" flag to optimize the LNA
combining algorithm when processing subframes in
an A-MPDU. This doesn't appear to work well in practice,
so revert it and use the old method of relying on
"rs_moreaggr".
Cc: stable@vger.kernel.org # 3.11
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This might trip up tx completion processing, although the condition that
triggers this should not (yet) occur in practice.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes a regression from commit
"ath9k: shrink a few data structures by reordering fields"
When cloning a buffer, the stale flag (part of bf_state now) needs to be
reset after copying the state to prevent tx processing hangs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also changed a log message to indicate that memory was not allocated
instead of memory not available!
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my patch c194992cbe ("skge: fix
broken driver") I didn't fix the skge bug correctly. The value of the
new mapping (not old) was passed to pci_unmap_single.
If we enable CONFIG_DMA_API_DEBUG, it results in this warning:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:986 check_sync+0x4c4/0x580()
skge 0000:02:07.0: DMA-API: device driver tries to sync DMA memory it has
not allocated [device address=0x000000023a0096c0] [size=1536 bytes]
This patch makes the skge driver pass the correct value to
pci_unmap_single and fixes the warning. It copies the old descriptor to
on-stack variable "ee" and unmaps it if mapping of the new descriptor
succeeded.
This patch should be backported to 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b9871bcf "bnx2x: VF RSS support - PF side" has deprecated one of
the previous existing messages. If an old VF driver were to send this message
to the PF then the PF will not reply and leave the mailbox in an unsteady
state (and cause a timeout on the VF side).
Wait until firmware ack is written before unlocking channel
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During flows which mask block attentions (e.g., register dump) all parities
are masked. However, unlike other blocks the MCP's attention is not masked
inside the block but rather the indication to the driver. If another attention
(e.g., link change) will occour while there's an MCP parity, the driver will
ignore the fact that the parity is masked and erroneously report a parity.
This patch forces the driver to read the MCP masking while checking for
parities.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During error flows while loading cnic the return value was incorrectly replaced
by that of bnx2x_set_real_num_queues(); If that function was to finish
successfully then the cnic would have mistakenly thought the load ended
successfully, causing issues (& panics) later on.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_iov_static_resc() should be called after IGU was read for information on
the number of available VFs, so that resources will be correctly set.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to incorrect usage of PF macros when reading information relating to
interrupts, some PFs were erroneously unable to support VFs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When system CPU is stressed it's possible that the driver will not be able
to pulse the FW every second, which will cause the log to be filled with
error messages.
Increasing the threshold to 5 seconds seems to be enough to eliminate the
issue.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 848xx PHY (10G-baseT), half-duplex was always advertised regardless of the
actual configuration. Change the 848xx duplex settings to advertise half-duplex
only if configured.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Warpcore mode setting when active DAC (Direct Attached Cable) is detected.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when 1G-optic module was plugged in, internal loopback test failed because the
driver used to check the optic module (with no need), and for 1G optic module,
the link speed was forced down to 1G, while the XMAC (10G MAC) was enabled.
This patch avoid accessing optic module in case internal loopback was selected,
and update the link speed in case 1G optic module was detected during init
stage.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relocate bnx2x_disable_kr2 function, and use it to disable KR2 in case it is not
configured in order to clear it's configuration, otherwise the link may come up
at 20G instead of the requested 10G-KR. In addition, restart AN after
disabling KR2 as part of the KR2 work-around.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, in case of KR link down, the driver would reset the PHY and restart
auto negotiation only when old Warpcore microcode was used (below D108).
This patch comes to generalize this by keep trying to restart KR link,
regardless of Warpcore microcode, since it was found that it solves another link
issue which source is a link-partner. As part of this change, the signal
detect is no longer a condition to apply the work-around to cover this new case.
Like before, as long as the link is down, AN will be restarted every 2 seconds.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Daniel Pieczko fixed two bugs in reset handling that particularly
affected the new SFC9120 controller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The old implementation was heavy on str* functions and sprintf calls.
This version is more manual, but faster.
Profiling just the printing of a 3 char CAN-id resulted in 60 instructions
for the manual method and over 2000 for the sprintf method. Bear in
mind the profiling was done against libc and not the kernel sprintf.
Together with this rewrite an issue with sending and receiving of RTR frames
has been fixed by Oliver for the cases that the DLC is not zero.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The locking is needed, since the the internal buffer for the CAN frames is
changed during the wakeup call. This could cause buffer inconsistencies
under high loads, especially for the outgoing short CAN packet skbuffs.
The needed locks led to deadlocks before commit
"5ede52538ee2b2202d9dff5b06c33bfde421e6e4 tty: Remove extra wakeup from pty
write() path", which removed the direct callback to the wakeup function from the
tty layer.
As slcan.c is based on slip.c the issue in the original code is fixed, too.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx and rx urbs are not deallocated if something goes wrong in peak_usb_start().
The patch fixes error handling to deallocate all the resources.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The SFC9120 MC firmware often takes longer than 20ms to reboot and
update the warm boot count in BIU_MC_SFT_STATUS_REG. A timeout of
250ms is very generous for an MC reboot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Scheduling a reset following an MC reboot event before waiting for
reboot to complete results in a race that can lead to a state where
must_realloc_vis is false in efx_ef10_fini_dmaq() but the VIs have
been destroyed during the MC reboot.
To avoid MC errors when trying to remove VIs that do not exist, wait
for the MC reboot to complete before scheduling the reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Pull networking fixes from David Miller:
1) If the local_df boolean is set on an SKB we have to allocate a
unique ID even if IP_DF is set in the ipv4 headers, from Ansis
Atteka.
2) Some fixups for the new chipset support that went into the sfc
driver, from Ben Hutchings.
3) Because SCTP bypasses a good chunk of, and actually duplicates, the
logic of the ipv6 output path, some IPSEC things don't get done
properly. Integrate SCTP better into the ipv6 output path so that
these problems are fixed and such issues don't get missed in the
future either. From Daniel Borkmann.
4) Fix skge regressions added by the DMA mapping error return checking
added in v3.10, from Mikulas Patocka.
5) Kill some more IRQF_DISABLED references, from Michael Opdenacker.
6) Fix races and deadlocks in the bridging code, from Hong Zhiguo.
7) Fix error handling in tun_set_iff(), in particular don't leak
resources. From Jason Wang.
8) Prevent format-string injection into xen-netback driver, from Kees
Cook.
9) Fix regression added to netpoll ARP packet handling, in particular
check for the right ETH_P_ARP protocol code. From Sonic Zhang.
10) Try to deal with AMD IOMMU errors when using r8169 chips, from
Francois Romieu.
11) Cure freezes due to recent changes in the rt2x00 wireless driver,
from Stanislaw Gruszka.
12) Don't do SPI transfers (which can sleep) in interrupt context in
cw1200 driver, from Solomon Peachy.
13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719.
From Nithin Sujir.
14) Make xen_netbk_count_skb_slots() count the actual number of slots
that will be used, taking into consideration packing and other
issues that the transmit path will run into. From David Vrabel.
15) Use the correct maximum age when calculating the bridge
message_age_timer, from Chris Healy.
16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey
Khoroshilov.
17) Netfilter conntrack extensions were converted to RCU but are not
always freed properly using kfree_rcu(). Fix from Michal Kubecek.
18) VF reset recovery not being done correctly in qlcnic driver, from
Manish Chopra.
19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko.
20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang.
21) Internal switch not initialized properly in bgmac driver, from Rafał
Miłecki.
22) Netlink messages report wrong local and remote addresses in IPv6
tunneling, from Ding Zhi.
23) ICMP redirects should not generate socket errors in DCCP and SCTP.
We're still working out how this should be handled for RAW and UDP
sockets. From Daniel Borkmann and Duan Jiong.
24) We've had several bugs wherein the network namespace's loopback
device gets accessed after it is free'd, NULL it out so that we can
catch these problems more readily. From Eric W Biederman.
25) Fix regression in TCP RTO calculations, from Neal Cardwell.
26) Fix too early free of xen-netback network device when VIFs still
exist. From Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
netconsole: fix a deadlock with rtnl and netconsole's mutex
netpoll: fix NULL pointer dereference in netpoll_cleanup
skge: fix broken driver
ip: generate unique IP identificator if local fragmentation is allowed
ip: use ip_hdr() in __ip_make_skb() to retrieve IP header
xen-netback: Don't destroy the netdev until the vif is shut down
net:dccp: do not report ICMP redirects to user space
cnic: Fix crash in cnic_bnx2x_service_kcq()
bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
vxlan: Avoid creating fdb entry with NULL destination
tcp: fix RTO calculated from cached RTT
drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>
net loopback: Set loopback_dev to NULL when freed
batman-adv: set the TAG flag for the vid passed to BLA
netfilter: nfnetlink_queue: use network skb for sequence adjustment
net: sctp: rfc4443: do not report ICMP redirects to user space
net: usb: cdc_ether: use usb.h macros whenever possible
net: usb: cdc_ether: fix checkpatch errors and warnings
net: usb: cdc_ether: Use wwan interface for Telit modules
ip6_tunnels: raddr and laddr are inverted in nl msg
...
This bug was introduced by commit
7a163bfb7c ("netconsole: avoid a crash with
multiple sysfs writers"). In store_enabled() we have the following
sequence: acquire nt->mutex then rtnl, but in the netconsole netdev
notifier we have rtnl then nt->mutex effectively leading to a deadlock.
The NULL pointer dereference that the above commit tries to fix is
actually due to another bug in netpoll_cleanup(). This is fixed by dropping
the mutex from the netdev notifier as it's already protected by rtnl.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch 136d8f377e broke the skge driver.
Note this part of the patch:
+ if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) {
+ dev_kfree_skb(nskb);
+ goto resubmit;
+ }
+
pci_unmap_single(skge->hw->pdev,
dma_unmap_addr(e, mapaddr),
dma_unmap_len(e, maplen),
PCI_DMA_FROMDEVICE);
skb = e->skb;
prefetch(skb->data);
- skge_rx_setup(skge, e, nskb, skge->rx_buf_size);
The function skge_rx_setup modifies e->skb to point to the new skb. Thus,
after this change, the new buffer, not the old, is returned to the
networking stack.
This bug is present in kernels 3.11, 3.11.1 and 3.12-rc1. The patch should
be queued for 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Vasiliy Glazov <vascom2@gmail.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If local fragmentation is allowed, then ip_select_ident() and
ip_select_ident_more() need to generate unique IDs to ensure
correct defragmentation on the peer.
For example, if IPsec (tunnel mode) has to encrypt large skbs
that have local_df bit set, then all IP fragments that belonged
to different ESP datagrams would have used the same identificator.
If one of these IP fragments would get lost or reordered, then
peer could possibly stitch together wrong IP fragments that did
not belong to the same datagram. This would lead to a packet loss
or data corruption.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, if a frontend cycles through states Closing
and Closed (which Windows frontends need to do) then the netdev
will be destroyed and requires re-invocation of hotplug scripts
to restore state before the frontend can move to Connected. Thus
when udev is not in use the backend gets stuck in InitWait.
With this patch, the netdev is left alone whilst the backend is
still online and is only de-registered and freed just prior to
destroying the vif (which is also nicely symmetrical with the
netdev allocation and registration being done during probe) so
no re-invocation of hotplug scripts is required.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 104a43edb2
cnic: Use CHIP_NUM macros from bnx2x.h
changed the code to use the bnx2x macro NO_FCOE() to determine if FCoE
is supported or not. There is another place in cnic that is still using
the old method to determine if FCoE is supported or not. The 2 methods
may not yield the same result after the network interface is brought down
and up. This will cause the crash as cnic_bnx2x_service_kcq() will access
the uninitialized cp->kcq2.
The fix is to consistently use the same macro CNIC_SUPPORTS_FCOE() which
uses the bnx2x NO_FCOE() macro. As a follow-up, we can clean up the code
to remove the old method as it is no longer needed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b9871bcfd2
bnx2x: VF RSS support - PF side
changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc. For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit afbd8bae9c
vxlan: add implicit fdb entry for default destination
creates an implicit fdb entry for default destination. This results
in an invalid fdb entry if default destination is not specified.
For ex:
ip link add vxlan1 type vxlan id 100
creates the following fdb entry
00:00:00:00:00:00 dev vxlan1 dst 0.0.0.0 self permanent
This patch fixes this issue by creating an fdb entry only if a
valid default destination is specified.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clears following warnings :
WARNING: Use include <linux/io.h> instead of <asm/io.h>
WARNING: Use include <linux/uaccess.h> instead of <asm/uaccess.h>
Signed-off-by: Avinash Kumar <avi.kp.137@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has recently turned up that we have a number of long standing bugs
in the network stack cleanup code with use of the loopback device
after it has been freed that have not turned up because in most cases
the storage allocated to the loopback device is not reused, when those
accesses happen.
Set looback_dev to NULL to trigger oopses instead of silent data corrupt
when we hit this class of bug.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Some bug fixes and future-proofing for the recently added SFC9120
support:
1. Minimal support for the 40G configuration.
2. Disable the incomplete PTP/hardware timestamping support.
3. Reset MAC stats properly after a firmware upgrade.
4. Re-check the datapath firmware capabilities after the controller is
reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use USB_DEVICE_AND_INTERFACE_INFO and USB_VENDOR_AND_INTERFACE_INFO
macros to reduce boilerplate.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: <stable@vger.kernel.org> # 3.0+ as far back as it applies cleanly
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. The max expected
value is 0xF, so now it should be possible to read decimal form ("15")
and hex form ("0xF").
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.
Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Use separate table for alias entries in the ehea module, otherwise the
probe() function will operate on the separate ports instead of the
lhea-"root" entry of the device-tree
Addresses https://bugzilla.novell.com/show_bug.cgi?id=435215
[ Thadeu notes that: "... this issue might happen with the generation of
initrd, when the scripts check for /sys/class/net/eth0/device/modalias,
which links to the port device at
/sys/devices/ibmebus/23c00400.lhea/port0/" ]
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Olaf Hering <ohering@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver registration fails, we need to clean up the resources allocated
before. cxgb4 missed to destroy the workqueue allocated at the very beginning.
This patch destroies the workqueue when registration fails.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
running bonding in ALB mode requires that learning packets be sent periodically,
so that the switch knows where to send responding traffic. However, depending
on switch configuration, there may not be any need to send traffic at the
default rate of 3 packets per second, which represents little more than wasted
data. Allow the ALB learning packet interval to be made configurable via sysfs
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Acked-by: Veaceslav Falico <vfalico@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes sparse warnings when incorrectly handling the port number
and using int instead of unsigned int iterating through &vn->sock_list[].
Keeping the port as __be16 also makes things clearer wrt endianess.
Also, it was pointed out that vxlan_get_rx_port() had unnecessary checks
which got removed.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o At the time of firmware hang "adapter->need_fw_reset" variable gets
set but after re-initialization of firmware OR at the time of VF
re-initialization that variable was not getting cleared which
was leading to failure in VF reset recovery.Fix it by clearing
this variable before re-initializing VF
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/toshiba/ps3_gelic_net.c
It's a NOOP since 2.6.35 and I will remove it one day ;)
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
code in drivers/net/ethernet/smsc/
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/pasemi/pasemi_mac.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
code in drivers/net/ethernet/natsemi/
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/micrel/ks8851_mll.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/lantiq_etop.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/hp/hp100.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/freescale/fec_main.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS fixes from Ralf Baechle:
"These are four patches for three construction sites:
- Fix register decoding for the combination of multi-core processors
and multi-threading.
- Two more fixes that are part of the ongoing DECstation resurrection
work. One of these touches a DECstation-only network driver.
- Finally Markos' trivial build fix for the AP/SP support.
(With this applied now all MIPS defconfigs are building again)"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: kernel: vpe: Make vpe_attrs an array of pointers.
MIPS: Fix SMP core calculations when using MT support.
MIPS: DECstation I/O ASIC DMA interrupt handling fix
MIPS: DECstation HRT initialization rearrangement
Use the already existing pm_cap variable in struct pci_dev for
determining the power management offset. This saves the driver from
having to keep track of an extra variable.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the already existing pm_cap variable in struct pci_dev for
determining the power management offset. This saves the driver from
having to keep track of an extra variable.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pci_enable_device_mem() will set device power state to D0,
so it's no need to do it again in alx_probe().
Also remove redundant PM Cap find code, because pci core
has been saved the pci device pm cap value.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to ixgbe and e1000e.
Jacob provides a ixgbe patch to fix the configure_rx patch to properly
disable RSC hardware logic when a user disables it. Previously we only
disabled RSC in the queue settings, but this does not fully disable
hardware RSC logic which can lead to unexpected performance issues.
Emil provides three fixes for ixgbe. First fixes the ethtool loopback
test when DCB is enabled, where the frames may be modified on Tx
(by adding VLAN tag) which will fail the check on receive. Then a fix
for QSFP+ modules, limit the speed setting to advertise only one speed
at a time since the QSFP+ modules do not support auto negotiation.
Lastly, resolve an issue where the driver will display incorrect info
for QSFP+ modules that were inserted after the driver has been loaded.
David Ertman provides to fixes for e1000e, one removes a comparison to
the boolean value true where evaluating the lvalue will produce the
same result. The other fixes an error in the calculation of the
rar_entry_count, which causes a write of unkown/undefined register
space in the MAC to unknown/undefined register space in the PHY.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When copying the MAC RAR registers to PHY there is an error in the
calculation of the rar_entry_count, which causes a write of unknown/
undefined register space in the MAC to unknown/undefined register space in
the PHY.
This patch fixes the overrun with writing to the PHY RAR and also fixes the
ethtool offline register tests so that the correctly addressed registers
have the appropriate bitmasks for R/W and RO bits for affected parts.
Shawn Rader gets credit for finding and fixing the register overrun.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
CC: Shawn Rader <shawn.t.rader@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removing a comparison to the boolean value true where simply interrogating
the lvalue will produce the same result.
Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves an issue where the driver will display incorrect info
for Q/SFP+ modules that were inserted after the driver has been loaded.
This patch adds a call to identify_phy() in ixgbe_get_settings() prior to
calling get_link_capabilities() which needs the PHY data in order to
determine the correct settings.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
QSFP+ modules do not support auto negotiation and should advertise only
one speed at a time.
This patch adds logic in ethtool to allow setting and reporting the
advertised speed at either 1Gbps or 10Gbps, but not both. Also limits
the speed set in ixgbe_sfp_link_config_subtask() to highest supported.
Previously the link was set to whatever the supported speeds were.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch disables DCB prior to running the loopback test.
When DCB is enabled the frames may be modified on Tx (by adding vlan tag)
which will fail the check on Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies the configure_rx path in order to properly disable RSC
hardware logic when the user disables it. Previously we only disabled RSC in the
queue settings, but this does not fully disable hardware RSC logic which can
lead to some unexpected performance issues.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.
Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle). Otherwise the handler is
reentered over and over again.
The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared. Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'. Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If rx_urb allocation fails in mcs_setup_urbs(), tx_urb leaks.
If mcs_receive_start() fails in mcs_net_open(), the both urbs are not deallocated.
The patch fixes the issues and by the way fixes label indentation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is down, CQs are freed. We must check the device state
to avoid issuing firmware commands on non existing CQs.
CC: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/dec/tulip/de4x5.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/amd/sun3lance.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/ibm/ehea/ehea_main.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/adi/bfin_mac.c.
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VM is providing an iSCSI target and the LUN is used by the
backend domain, the generated skbs for direct I/O writes to the disk
have large, multi-page skb->data but no frags.
With some lengths and starting offsets, xen_netbk_count_skb_slots()
would be one short because the simple calculation of
DIV_ROUND_UP(skb_headlen(), PAGE_SIZE) was not accounting for the
decisions made by start_new_rx_buffer() which does not guarantee
responses are fully packed.
For example, a skb with length < 2 pages but which spans 3 pages would
be counted as requiring 2 slots but would actually use 3 slots.
skb->data:
| 1111|222222222222|3333 |
Fully packed, this would need 2 slots:
|111122222222|22223333 |
But because the 2nd page wholy fits into a slot it is not split across
slots and goes into a slot of its own:
|1111 |222222222222|3333 |
Miscounting the number of slots means netback may push more responses
than the number of available requests. This will cause the frontend
to get very confused and report "Too many frags/slots". The frontend
never recovers and will eventually BUG.
Fix this by counting the number of required slots more carefully. In
xen_netbk_count_skb_slots(), more closely follow the algorithm used by
xen_netbk_gop_skb() by introducing xen_netbk_count_frag_slots() which
is the dry-run equivalent of netbk_gop_frag_copy().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 989038e217 ("tg3: Don't turn off
led on 5719 serdes port 0") added code to skip turning led off on port
0 of the 5719 since it powered down other ports. This workaround needs
to be enabled on the 5720 as well.
Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c8d68e6be1
(tuntap: multiqueue support) only call free_netdev() on error in
tun_set_iff(). This causes several issues:
- memory of tun security were leaked
- use after free since the flow gc timer was not deleted and the tfile
were not detached
This patch solves the above issues.
Reported-by: Wannes Rombouts <wannes.rombouts@epitech.eu>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure a format string cannot accidentally leak into the
kthread_run() call.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control is defined in the four EEPROM sections but the driver only reads
from section 0.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where some ports can fail to initialize on a
cold boot. This patch adds an additional call to read the PHY id for i354
devices in order workaround the hardware problem.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This is a pull request for a few early fixes for the 3.12 stream.
Alexey Khoroshilov corrects a use-after-free issue on rtl8187 found
by the Linux Driver Verification project.
Arend van Spriel provides a brcmfmac patch to fix a build issue
reported by Randy Dunlap.
Hauke Mehrtens offers a bcma fix to properly account for the storage
width of error code values before checking them.
Solomon Peachy brings a pair of cw1200 fixes to avoid hangs in that
driver with SPI devices. One avoids transfers in interrupt context,
the other fixes a locking issue.
Stanislaw Gruszka changes the initialization of the rt2800 driver to
avoid a freeze, addressing a bug in the Red Hat bugzilla.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Same narrative as eb2dc35d99 ("r8169: RxConfig
hack for the 8168evl.") regarding AMD IOMMU errors.
RTL_GIGA_MAC_VER_36 - 8168f as well - has not been reported to behave the
same.
Tested-by: David R <david@unsolicited.net>
Tested-by: Frédéric Leroy <fredo@starox.org>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the device list from the Windows driver description files
included with a new Qualcomm MDM9615 based device, "Alcatel-sbell
ASB TL131 TDD LTE", from China Mobile. This device is tested
and verified to work. The others are assumed to work based on
using the same Windows driver.
Many of these devices support multiple QMI/wwan ports, requiring
multiple interface matching entries. All devices are composite,
providing a mix of one or more serial, storage or Android Debug
Brigde functions in addition to the wwan function.
This device list included an update of one previously known device,
which was incorrectly assumed to have a Gobi 2K layout. This is
corrected.
Reported-by: 王康 <scateu@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series implements the new i40e driver for Intel's upcoming
Intel(R) Ethernet Controller XL710 Family of devices.
V7: many changes from a few comments:
use linux errno types
change I40E_SUCCESS to 0, standardize returns
change s32 return values to int
use void return values where possible
prefer use of int over i40e_status
V6: rename Kbuild to Makefile
rename i40e_mem[set|cpy] to regular memset/memcpy
V5: remove sysfs support from this set, will rearchitect
changes from community comments
V4: addresses remaining community comments, mostly trivial edits.
major sparse based cleanup of possible endian issues
removal of most of __func__ references
sizeof(*var) instead of sizeof(struct ...)
change 'NULL ==' tests to !NULL
implement xps
use kernel bitshift macros (upper_32_bits, etc)
V3: many more individual comments addressed, thanks reviewers! Many
other changes due to internal review and development.
V2: each patch has individual comments, in general, feedback from the
list was applied and addressed. Many changes due to internal review
and coding as well.
V1: initial send
Let me start by saying thanks and we appreciate any time spent by
those of you who review and comment on this new driver, and we will
attempt to address and respond to all issues brought to our attention.
I tried to break the patches up to ease review, but the series should
apply and still be bisectable, as the last patch adds the driver to
the kernel compile with CONFIG_I40E.
This driver is for a brand new bit of silicon that has a different
design than other Intel Ethernet silicon, and therefore needed a new
driver.
The hardware has quite a bit of capability and this driver is only
meant to provide basic functionality at first. Future patches will
continue to add functionality and bug fixes.
This initial release is very early in the product cycle with the intent
of getting initial support into the kernel before users have the
hardware available to purchase. A software development manual is not
ready yet but will be available when the hardware ships.
The driver development model and interaction with community submitted
patches *will not be any different* than what we are currently doing
today. We plan to continue established processes.
An associated i40evf driver has been posted for review.
List of tools we ran in preparation:
way more sparse clean
make W=1, W=2 clean
checkpatch (almost) clean
total: 1 errors, 4 warnings, 30461 lines checked
NOTE: Ignored message types: LONG_LINE
- issues have been addressed and the remainders
are noise.
codespell clean
smatch (almost) clean with a couple minor warnings
coccicheck clean
namespacecheck clean
allmodconfig clean
ppc64 build clean (untested)
This driver is a team effort, thank you to Joseph Gasparakis,
Shannon Nelson, Anjali Singhai-Jain, Mitch Williams, Neerav
Parikh, Vasu Dev, Kavindya Deegala, Yi Zou, and PJ Waskiewicz.
TODO (known issues)
BQL implementation
finish rtnl_stat64 locking (we have a patch but debugging it)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The "id" variable was being incremented in common code, but only
initialized and used in IPv4 code. We move the increment to the IPv4
code too, and then legitimately use the uninitialized_var() macro to
avoid the gcc 4.6 warning that 'id' may be used uninitialized.
Note that gcc 4.7 does not warn.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/broadcom/bcm63xx_enet.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from
drivers/net/ethernet/korina.c
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently macvlan calls skb_clone in macvlan_broadcast but checks
for a NULL return in macvlan_broadcast_one instead. This is
needlessly confusing and may lead to bugs introduced later.
This patch moves the error check to where the skb_clone call is.
The only other caller of macvlan_broadcast_one never passes in a
NULL value so it doesn't need the check either.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Thanks,
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c: In function 'qlcnic_handle_fw_message':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c:922:4: warning: overflow in implicit constant conversion [-Woverflow]
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We make bond_arp_rcv global so it can be used in bond_sysfs if the bond
interface is up and arp_interval is being changed to a positive value
and cleared otherwise as per Jay's suggestion.
This also fixes a problem where bond_arp_rcv was set even though
arp_validate was disabled while the bond was up by unsetting recv_probe
in bond_store_arp_validate and respectively setting it if enabled.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to protect store_arp_validate via rtnl because it can race with
mode changing and we can end up having arp_validate set in a mode
different from active-backup.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andi Kleen