Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
IPCB may contain data from previous layers (in the observed case the
qdisc layer). In the observed scenario, the data was misinterpreted as
ip header options, which later caused the ihl to be set to an invalid
value (<5). This resulted in an infinite loop in the mips implementation
of ip_fast_csum.
This patch clears IPCB(skb)->opt before dst_link_failure can be called for
various types of tunnels. This change only applies to encapsulated ipv4
packets.
The code introduced in 11c21a30 which clears all of IPCB has been removed
to be consistent with these changes, and instead the opt field is cleared
unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to
SIT, GRE, and IPIP tunnels.
The relevant vti, l2tp, and pptp functions already contain similar code for
clearing the IPCB.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by gre
as it modifies the skb on xmit.
Also, clean up whitespace in ipgre_tap_setup when we're already touching it.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fix a potential race into the existing tunnel code, which
could lead to the wrong dst to be permanenty cached:
CPU1: CPU2:
<xmit on ip6_tunnel>
<cache lookup fails>
dst = ip6_route_output(...)
<tunnel params are changed via nl>
dst_cache_reset() // no effect,
// the cache is empty
dst_cache_set() // the wrong dst
// is permanenty stored
// into the cache
With the new dst implementation the above race is not possible
since the first cache lookup after dst_cache_reset will fail due
to the timestamp check
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Parameters were updated only if the kernel was unable to find the tunnel
with the new parameters, ie only if core pamareters were updated (keys,
addr, link, type).
Now it's possible to update ttl, hoplimit, flowinfo and flags.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like many files are including mroute.h unnecessarily, so remove
the include. Most importantly remove it from ipv6.
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently error log messages in ip6gre_err are printed at 'warn'
level. This is different to most other tunnel types which don't
print any messages. These log messages don't provide any information
that couldn't be deduced with networking tools. Also it can be annoying
to have one end of the tunnel go down and have the logs fill with
pointless messages such as "Path to destination invalid or inactive!".
This patch reduces the log level of these messages to 'dbg' level to
bring the visible behaviour into line with other tunnel types.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problems in the current dst_entry cache in the ip6_tunnel:
1. ip6_tnl_dst_set is racy. There is no lock to protect it:
- One major problem is that the dst refcnt gets messed up. F.e.
the same dst_cache can be released multiple times and then
triggering the infamous dst refcnt < 0 warning message.
- Another issue is the inconsistency between dst_cache and
dst_cookie.
It can be reproduced by adding and removing the ip6gre tunnel
while running a super_netperf TCP_CRR test.
2. ip6_tnl_dst_get does not take the dst refcnt before returning
the dst.
This patch:
1. Create a percpu dst_entry cache in ip6_tnl
2. Use a spinlock to protect the dst_cache operations
3. ip6_tnl_dst_get always takes the dst refcnt before returning
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a prep work to fix the dst_entry refcnt bugs in
ip6_tunnel.
This patch rename:
1. ip6_tnl_dst_check() to ip6_tnl_dst_get() to better
reflect that it will take a dst refcnt in the next patch.
2. ip6_tnl_dst_store() to ip6_tnl_dst_set() to have a more
conventional name matching with ip6_tnl_dst_get().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a prep work to fix the dst_entry refcnt bugs in ip6_tunnel.
This patch refactors some common init codes used by both
ip6gre_tunnel_init and ip6gre_tap_init.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a tunnel is deleted, the cached dst entry should be released.
This problem may prevent the removal of a netns (seen with a x-netns IPv6
gre tunnel):
unregister_netdevice: waiting for lo to become free. Usage count = 3
CC: Dmitry Kozlov <xeb@mail.ru>
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: huaibin Wang <huaibin.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the meaning of net.ipv6.auto_flowlabels to provide a mode for
automatic flow labels generation. There are four modes:
0: flow labels are disabled
1: flow labels are enabled, sockets can opt-out
2: flow labels are allowed, sockets can opt-in
3: flow labels are enabled and enforced, no opt-out for sockets
np->autoflowlabel is initialized according to the sysctl value.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't call skb_get_hash here since the packet is not complete to do
flow_dissector. Create hash based on flowi6 instead.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code there just open-codes the same, so use the provided macro instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That was we can make sure the output path of ipv4/ipv6 operate on
the UDP socket rather than whatever random thing happens to be in
skb->sk.
Based upon a patch by Jiri Pirko.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Don't use dev->iflink anymore.
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those are counterparts to nla_put_in_addr and nla_put_in6_addr.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP addresses are often stored in netlink attributes. Add generic functions
to do that.
For nla_put_in_addr, it would be nicer to pass struct in_addr but this is
not used universally throughout the kernel, in way too many places __be32 is
used to store IPv4 address.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 code uses a mixture of coding styles. In some instances check for NULL
pointer is done as x != NULL and sometimes as x. x is preferred according to
checkpatch and this patch makes the code consistent by adopting the latter
form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 code uses a mixture of coding styles. In some instances check for NULL
pointer is done as x == NULL and sometimes as !x. !x is preferred according to
checkpatch and this patch makes the code consistent by adopting the latter
form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
info is in network byte order, change it back to host byte order
before use. In particular, the current code sets the MTU of the tunnel
to a wrong (too big) value.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is
added to rtnetlink messages.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is
added to rtnetlink messages.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using GRE redirection in WCCP, it sets the wrong skb->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Yuri Chislov <yuri.chislov@gmail.com>
Tested-by: Yuri Chislov <yuri.chislov@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we need the IP6_TNL_F_CAP_XMIT capabiltiy to transmit
packets through an ipv6 tunnel. This capability is set when the
tunnel gets configured, based on the tunnel endpoint addresses.
On tunnels with wildcard tunnel endpoints, we need to do the
capabiltiy checking on a per packet basis like it is done in
the receive path.
This patch extends ip6_tnl_xmit_ctl() to take local and remote
addresses as parameters to allow for per packet capabiltiy
checking.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise it gets overwritten by register_netdev().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.
Current handling of IFF_XMIT_DST_RELEASE is not optimal.
Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y
The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.
As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.
This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.
Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :
dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
netif_keep_dst(dev);
Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.
The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
In xmit path, we build a flowi6 which will be used for the output route lookup.
We are sending a GRE packet, neither IPv4 nor IPv6 encapsulated packet, thus the
protocol should be IPPROTO_GRE.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Reported-by: Matthieu Ternisien d'Ouville <matthieu.tdo@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_set_inner_protocol to set inner Ethernet protocol to
protocol being encapsulation by GRE before tunnel_xmit. This is
needed for GSO if UDP encapsulation (fou) is being done.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6gre_tunnel_locate() should not return an existing tunnel if
create is true. Otherwise it is possible to add the same
tunnel multiple times without getting an error.
So return NULL if the tunnel that should be created already
exists.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this alias, we don't need to load manually the module before adding an
ip6gretap interface with iproute2.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Automatically generate flow labels for IPv6 packets on transmit.
The flow label is computed based on skb_get_hash. The flow label will
only automatically be set when it is zero otherwise (i.e. flow label
manager hasn't set one). This supports the transmit side functionality
of RFC 6438.
Added an IPv6 sysctl auto_flowlabels to enable/disable this behavior
system wide, and added IPV6_AUTOFLOWLABEL socket option to enable this
functionality per socket.
By default, auto flowlabels are disabled to avoid possible conflicts
with flow label manager, however if this feature proves useful we
may want to enable it by default.
It should also be noted that FreeBSD has already implemented automatic
flow labels (including the sysctl and socket option). In FreeBSD,
automatic flow labels default to enabled.
Performance impact:
Running super_netperf with 200 flows for TCP_RR and UDP_RR for
IPv6. Note that in UDP case, __skb_get_hash will be called for
every packet with explains slight regression. In the TCP case
the hash is saved in the socket so there is no regression.
Automatic flow labels disabled:
TCP_RR:
86.53% CPU utilization
127/195/322 90/95/99% latencies
1.40498e+06 tps
UDP_RR:
90.70% CPU utilization
118/168/243 90/95/99% latencies
1.50309e+06 tps
Automatic flow labels enabled:
TCP_RR:
85.90% CPU utilization
128/199/337 90/95/99% latencies
1.40051e+06
UDP_RR
92.61% CPU utilization
115/164/236 90/95/99% latencies
1.4687e+06
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_checksum_simple_validate to verify checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to switch the netns when packet is encapsulated or
decapsulated. In other word, the encapsulated packet is received in a netns,
where the lookup is done to find the tunnel. Once the tunnel is found, the
packet is decapsulated and injecting into the corresponding interface which
stands to another netns.
When one of the two netns is removed, the tunnel is destroyed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to remove the FB tunnel with the command 'ip link del ip6gre0' but
this is unsafe, the module always supposes that this device exists. For example,
ip6gre_tunnel_lookup() may use it unconditionally.
Let's add a rtnl handler for dellink, which will never remove the FB tunnel (we
let ip6gre_destroy_tunnels() do the job).
Introduced by commit c12b395a46 ("gre: Support GRE over IPv6").
CC: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two places defined IPV6_TCLASS_SHIFT, so we should move it into ipv6.h,
and use this macro as possible. And define ip6_tclass helper to return
tclass
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are same, so unify them as one, pcpu_sw_netstats.
Define pcpu_sw_netstat in netdevice.h, remove pcpu_tstats
from if_tunnel and remove br_cpu_netstats from br_private.h
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And use it if possible.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to enable lockdep on seqcount/seqlock structures, we
must explicitly initialize any locks.
The u64_stats_sync structure, uses a seqcount, and thus we need
to introduce a u64_stats_init() function and use it to initialize
the structure.
This unfortunately adds a lot of fairly trivial initialization code
to a number of drivers. But the benefit of ensuring correctness makes
this worth while.
Because these changes are required for lockdep to be enabled, and the
changes are quite trivial, I've not yet split this patch out into 30-some
separate patches, as I figured it would be better to get the various
maintainers thoughts on how to best merge this change along with
the seqcount lockdep enablement.
Feedback would be appreciated!
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Roger Luethi <rl@hellgate.ch>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Horman <horms@verge.net.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Wensong Zhang <wensong@linux-vs.org>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1381186321-4906-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
David S. Miller