Gcc complains about this printk:
drivers/usb/renesas_usbhs/mod_gadget.c:188:3: warning: format ‘%x’
expects argument of type ‘unsigned int’, but argument 3 has type
‘dma_addr_t’ [-Wformat]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch tidyup below smatch complaint
drivers/usb/renesas_usbhs/mod_host.c +642 usbhsh_queue_done()
warn: variable dereferenced before check 'urb' (see line 636)
Special thanks to Dan
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Packet should be force removed when reset/detach
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without this patch, USB host hub shows error when cable was detached
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is possible to judge whether renesas_usbhs driver is running,
by checking attch irq mask.
This patch adds usbhsh_is_running() to check it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
attch interrupt might happen infinitely on some USB hub (self power?).
This patch disable attch irq after device attached,
and enable it again when detach irq happen.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
driver has to re-use the limited pipe for each device/endpoint
when it is USB host hub mode, since number of pipe has limitation.
Then, each pipe should care own pipe sequence for next packet.
This patch adds sequence control.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
driver has to re-use the limited pipe for each device/endpoint
when it is USB host hub mode, since number of pipe has limitation.
This patch adds usbhsh_pipe_attach/detach() functions for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds usbhsh_endpoint_detach_all() for error case.
usbhs_endpoitn_xxx() functions were moved to upper side in source code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current renesas_usbhs had been assigning udev to each urb.
It was executed even though it was device0.
For this reason, the device0 had to set the new device address
which has still not been assigned. (it will be assigned on next step).
Current renesas_usbhs used fixed address for it.
but it is not good for USB hub support.
This patch modifies this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usbhsh_ureq_free() is not enough when urb dequeued.
Without this patch, the driver can not recognize re-connected
USB device after USB hub disconnected
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usbhsh_urb_enqueue() didn't have error value when
usbhsh_device_attach() failed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
current renesas_usbhs is using new style udc_start/stop from
af1d7056a5
(usb: gadget: renesas: convert to new style).
with this patch we can finally remove the global "the_controller_link"
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When poping packet from queue, it needs correct end procedure.
This patch call usbhsg_queue_pop() in usbhsg_pipe_disable().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current renesas_usbhs driver always tries to send packet in end of recip handler.
But it breaks chapter 9 EndpointHalt test.
This patch fixup this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds basic get-status support for chapter 9 test.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds basic set-feature support for chapter 9 test.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
recip handler will call various functions which are holding
usbhs_lock.
This patch removes superfluous usbhs_lock from recip handler
to escape double lock.
[ balbi@ti.com : brushed up commit log a bit ]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit renames the “speed” field of the usb_gadget_driver
structure to “max_speed”. This is so that to make it more
apparent that the field represents the maximum speed gadget
driver can support.
This also make the field look more like fields with the same
name in usb_gadget and usb_composite_driver structures. All
of those represent the *maximal* speed given entity supports.
After this commit, there are the following fields in various
structures:
* usb_gadget::speed - the current connection speed,
* usb_gadget::max_speed - maximal speed UDC supports,
* usb_gadget_driver::max_speed - maximal speed gadget driver
supports, and
* usb_composite_driver::max_speed - maximal speed composite
gadget supports.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This commit replaces usb_gadget's is_dualspeed field with
a max_speed field.
[ balbi@ti.com : Fixed DWC3 driver ]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
current mod_host used usbhs_device_alloc/free(),
but allocated variable was attached to each xx->hcpriv.
The intuitively clear name was not xxx_alloc/free() but xxx_attach/detach().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
current mod_host used usbhs_endpoint_alloc/free(),
but allocated variable was attached to each xx->hcpriv.
The intuitively clear name was not xxx_alloc/free() but xxx_attach/detach().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch remove unneeded parameter from usbhsh_xx_queue_push()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this patch cleanup
- make sure static function
- remove unneeded label
- useless local variable were removed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
device0 was treated without checking in usbhsh_device_alloc().
but "udev->usbv" and "dev_set_drvdata()" will be overwritten
if device0 was multi-allocated.
This patch fixes this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
mod_host had usbhsh_request active/free list.
it was almost meaningless, and vainly complicated.
This patch remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
current usbhs_set_device_config() didn't care upphub/hubport.
This patch adds its value.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
it was device configuration setting function, not only speed.
This patch modify function name usbhs_set_device_speed() -> usbhs_set_device_config()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DCP data/status stage needs ureq to usbhs_pkt_push(),
but sometimes, there is no data stage.
In that case, allocated ureq was not freed,
Current ureq alloc/free pair were difficult to understand.
This patch removed unnecessary/un-understandable ureq alloc
from usbhsh_urb_enqueue(), and create simpler alloc/free pair.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs needs callback for notify hotplug.
but it were 2 methods which are almost same.
This patch unified these into one.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
renesas_usbhs driver use "req" for struct usb_ctrlrequest,
and "ureq" for struct usbhsh_request
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usbhs_sys_usb_ctrl() can collect into usbhs_sys_host/function_ctrl().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
usbhs_sys_hispeed_ctrl() can collect into usbhs_sys_host/function_ctrl().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch cares latest USB_SPEED_SUPER support.
renesas_usbhs can not use super-speed, but can use full/high speed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
current renesas_usbhs is using new style udc_start/stop from
af1d7056a5
(usb: gadget: renesas: convert to new style).
But current renesas_usbhs driver didn't care about gadget.dev.driver
when udc_stop. it cause rmmod oops.
This patch care it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
current renesas_usbhs is using new style udc_start/stop from
af1d7056a5
(usb: gadget: renesas: convert to new style).
cable disconnected signal was needed.
This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
current renesas_usbhs is using new style udc_start/stop from
af1d7056a5
(usb: gadget: renesas: convert to new style).
But bind() function will fail if it was called before
device_register() (or device_add()).
This patch modifies this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
new endpoint should start from DATA0,
but mod_host didn't care it.
This patch fix it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
renesas_usbhs is caring pipe type and its direction.
but current usbhs_endpoint_alloc() didn't check direction.
this patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix up the following section mismatch warnings:
WARNING: drivers/usb/renesas_usbhs/renesas_usbhs.o(.text+0xf5d): Section
mismatch in reference from the function usbhs_mod_probe() to the function
.devinit.text:usbhs_mod_host_probe() The function usbhs_mod_probe() references
the function __devinit usbhs_mod_host_probe(). This is often because
usbhs_mod_probe lacks a __devinit annotation or the annotation of
usbhs_mod_host_probe is wrong.
WARNING: drivers/usb/renesas_usbhs/renesas_usbhs.o(.text+0xfd7): Section
mismatch in reference from the function usbhs_mod_probe() to the function
.devexit.text:usbhs_mod_host_remove() The function usbhs_mod_probe() references
a function in an exit section. Often the function usbhs_mod_host_remove() has
valid usage outside the exit section and the fix is to remove the __devexit
annotation of usbhs_mod_host_remove.
WARNING: drivers/usb/renesas_usbhs/renesas_usbhs.o(.text+0x1005): Section
mismatch in reference from the function usbhs_mod_remove() to the function
.devexit.text:usbhs_mod_host_remove() The function usbhs_mod_remove()
references a function in an exit section. Often the function
usbhs_mod_host_remove() has valid usage outside the exit section and the fix is
to remove the __devexit annotation of usbhs_mod_host_remove.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dan Carpenter