These devices feature multiple interfaces/endpoints: a legacy BIOS/boot
interface (endpoint 0x81), as well as 2 corsair-specific keyboard interfaces
(endpoint 0x82, 0x83 IN/0x03 OUT) and an RGB LED control interface (endpoint
0x84 IN/0x04 OUT)
Because the extra 3 interfaces are not of subclass USB_INTERFACE_SUBCLASS_BOOT,
HID_QUIRK_NOGET is not automatically set on them and a 10s timeout per-endpoint
(30s per device) occurs initialising reports on boot. We configure
HID_QUIRK_NO_INIT_REPORTS for these devices.
Additionally the left-side G1-G18 macro keys on the K95RGB generate output on
the un-opened 0x82/0x83 endpoints which causes the keyboard to stop responding
waiting for this event to be collected. We enable HID_QUIRK_ALWAYS_POLL to
prevent this situation from occurring.
Signed-off-by: Trent Lloyd <trent@lloyd.id.au>
Tested-by: SUGNIAUX Wilfried <wsu@ppharm2k20.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Needed for v2 of the device firmware, otherwise kernel will stuck for few
seconds and throw "usb_submit_urb(ctrl) failed: -1" early on system boot.
Signed-off-by: Nazar Mokrynskyi <nazar@mokrynskyi.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for the Micrsift Digital 4K, Media 600 and Media 3000 V1 Keyboards,
which have the same quirks as the already existing hardware MS_NE4K.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=52841
[jkosina@suse.cz: rephrase changelog]
Signed-off-by: Alistair Leslie-Hughes <leslie_alistair@hotmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Asus X205TA and E200HA built-in keyboard contain wrong logical maximum value in
report descriptor.
This patch correct wrong logical maximum in report descriptor.
Signed-off-by: Yusuke Fujimaki <usk.fujimaki@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft Wireless Comfort Keyboard has vendor specific My Favorites
1-5 keys. Linux already supports this buttons on other MS keyboards by
MS_ERGONOMY quirk. So apply MS_ERGONOMY quirk to USB PID 0x00e3
(Microsoft Wireless Optical Desktop Receiver 3.0A). After this
My Favorites 1..5 keys will be reported as KEY_F14..KEY_F15 events.
Signed-off-by: Slava Bacherikov <slava@bacher09.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device which identifies itself as a "USB Keykoard" (no typo)
with VID:PID 1a2c:0027 does not seem to be handling the reports
initialization very well.
This results in a "usb_submit_urb(ctrl) failed: -1" message from the
kernel when connected, and a delay before its initialization. It can
also cause the hang the system.
This patch adds the quirk for this device, which causes the delay
to disappear. It is named as "USB Keykoard2" because the "USB Keykoard"
already exists.
Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The C-Media CM6533 is a USB audio chip featuring it's jack detection
capability.The device originates an interrupt transfer via HID interface each
time when a jack event occurs. The purpose of this patch is to handle hid raw
events to keep the operating system informed of user interactions.
Signed-off-by: Ben Chen <ben_chen@bizlinktech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The midi controller times-out while initializing reports, this
causes boot to take an extra 10 seconds. The device descriptor
advertises that it has an internal HID device but seems to not
actually do anything useful.
Signed-off-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The correct product ID for the old version of the raphnet 4nes4snes
device was 0x0a9d, not 0x0a8d.
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds rumble and LED support for nyko core controllers
using the sino lite chip vendor:1345 product:3008, for PS3.
Setting operational mode and output reports are the same as
sixaxis but the input report has a different format since the
PS3 accepts HID usb devices. For it to work, an exception is
needed to skip overriding the report descriptor and use the
original one.
Signed-off-by: Scott Moreau <oreaus@gmail.com>
Acked-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- appoint Benjamin Tissoires as co-maintainer / designated reviewer
- sysfs report_descriptor visibility fix for unclaimed devices, from
Andy Lutomirski
- suspend/resume fixes for Sony driver from Frank Praznik
- IRQ deadlock fix from Ioan-Adrian Ratiu
- hid-i2c fixes affecting (at least) Yoga 900 from Mika Westerberg and
Srinivas Pandruvada
- a lot of new device support (especially, but not limited to, Wacom)
and assorted small misc fixes
- almost complete G920 support; the only bit that is missing is
switching the device to HID mode automatically; Simon Wood and Michal
Maly are working on it.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (46 commits)
Revert "INPUT: xpad: switch Logitech G920 Wheel into HID mode"
HID: sensor-hub: Add quirk for Lenovo Yoga 900 with ITE Chips
HID: Add new PID for Microchip Pick16F1454
HID: wacom: Use correct report to query pen ID from INTUOSHT2 devices
HID: i2c-hid: Prevent sending reports from racing with device reset
HID: use kobj_to_dev()
HID: wiimote: use dev_to_wii()
HID: add a new helper to_hid_driver()
HID: use to_hid_device()
HID: move to_hid_device() to hid.h
HID: usbhid: use to_usb_device
HID: corsair: Convert to use module_hid_driver
HID: input: ignore the battery in OKLICK Laser BTmouse
HID: wacom: Fix pad button range for CINTIQ_COMPANION_2
HID: wacom: Fix touchring value reporting
HID: wacom: Report 'strip2' values in ABS_RY
HID: wacom: Limit touchstrip data to 13 bits
HID: wacom: bitwise vs logical ORs
HID: wacom: Apply lowres quirk to BAMBOO_TOUCH devices
HID: enable hid device to suspend/resume asynchronously
...
This needs same quirk as applied to other YOGA sensor hubs. Refer to commit
21589ebda6 ("HID: sensor-hub: Add in quirk for Lenovo Yogas with ITE")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There seems to be a new version of the Microchip Pick16F1454 with a
different PID (0xf2f7). This device should also be ignored by the HID
driver. The PID was observed with the second version of the Yepkit Ykush
USB hub.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Here are a number of small USB fixes for 4.4-rc5. All of them have been
in linux-next. The majority are gadget and phy issues, with a few new
quirks and device ids added as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlZs8fkACgkQMUfUDdst+ym/HwCgxdhop3PMk9QxCVaEdxcqv10p
PDkAn0uOW1sdRsHVRhutjcc29+AUJggk
=ybrB
-----END PGP SIGNATURE-----
Merge tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB driver fixes from Greg KH:
"Here are a number of small USB fixes for 4.4-rc5. All of them have
been in linux-next. The majority are gadget and phy issues, with a
few new quirks and device ids added as well"
* tag 'usb-4.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (32 commits)
USB: add quirk for devices with broken LPM
xhci: fix usb2 resume timing and races.
usb: musb: fail with error when no DMA controller set
usb: gadget: uvc: fix permissions of configfs attributes
usb: musb: core: Fix pm runtime for deferred probe
usb: phy: msm: fix a possible NULL dereference
USB: host: ohci-at91: fix a crash in ohci_hcd_at91_overcurrent_irq
usb: Quiet down false peer failure messages
usb: xhci: fix config fail of FS hub behind a HS hub with MTT
xhci: Fix memory leak in xhci_pme_acpi_rtd3_enable()
usb: Use the USB_SS_MULT() macro to decode burst multiplier for log message
USB: whci-hcd: add check for dma mapping error
usb: core : hub: Fix BOS 'NULL pointer' kernel panic
USB: quirks: Apply ALWAYS_POLL to all ELAN devices
usb-storage: Fix scsi-sd failure "Invalid field in cdb" for USB adapter JMicron
USB: quirks: Fix another ELAN touchscreen
usb: dwc3: gadget: don't prestart interrupt endpoints
USB: serial: Another Infineon flash loader USB ID
USB: cdc_acm: Ignore Infineon Flash Loader utility
USB: cp210x: Remove CP2110 ID from compatibility list
...
All ELAN hid devices seem to require the ALWAYS_POLL quirk. Let's use
this quirk for all devices from this vendor, rather than maintaining a
list of all its known product IDs.
Tested-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds basic support for the Logitech G920 wheel when in HID
mode. This wheel 'speaks' the HID++ protocol, and therefor is driven
with hid-logitech-hidpp.
At this stage the driver only shows that it can communicate with the
wheel by outputting the name discovered over HID++.
The normal HID functions work to give input functionality using
joystick/event interface.
Note: in 'hidpp_probe()' we have to start the hardware to get packets
flowing, the same might apply in future for other devices which don't
use the unifying protocol.
Signed-off-by: Simon Wood <simon@mungewell.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Without quirk keyboard repeats '6' until volume control is used since it
indicates the key is pressed without ever releasing.
Signed-off-by: Jimmy Berry <jimmy@boombatower.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch is a follow-up to 47eeca8a48 (" HID: sensor-hub: Add in quirk
for Lenovo Yogas with ITE")
The Lenovo Yoga 2 13 seems to be sold in multiple variants with minor
difference3s. IN my case, the USB ID for ITE chip is different than the
Yoga 2 11 and Yoga 3 14.
Without the quirk, no data is received from the accelerometer. I have
verified the patch, testing this on 4.3-rc4 (and 4.2 stable). With this
patch, proper orientation data is received.
rrs@learner:~/Community/UpstreamSources/linux-upstream_GIT (stable-42)$
monitor-sensor
** Message: Accelerometer orientation changed: bottom-up
** Message: Light changed: 0.000000 (lux)
±** Message: Accelerometer orientation changed: left-up
** Message: Accelerometer orientation changed: bottom-up
** Message: Accelerometer orientation changed: left-up
** Message: Accelerometer orientation changed: normal
** Message: Light changed: 29.999999 (lux)
monitor-sensor can be found in the iio-sensor-proxy tool.
Signed-off-by: Ritesh Raj Sarraf <rrs@debian.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The WiiU adapter from Mayflash (see
http://www.mayflash.com/Products/NINTENDOWiiU/W009.html) is not
working correctly.
The "XInput" mode works fine, the controller is recognized as a xbox
controller. But it is only possible to connect one controller with this method.
In "DInput" mode the device is recognized as some kind of mouse input but no
joystick is created. This commit will change this behavior with
HID_QUIRK_MULTI_INPUT to split the device into 4 input devices so that it will
also create joysticks in /dev/input/js*.
Signed-off-by: Oliver Schmitt <voltumna@gmx.net>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch implements a HID driver for the Corsair Vengeance K90 keyboard.
It fixes the behaviour of the keys using incorrect HID usage codes and exposes
the macro playback mode and current profile to the user space through sysfs
attributes. It also adds two LED class devices controlling the "record" LED and
the backlight.
Signed-off-by: Clément Vuchener <clement.vuchener@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds support for Microsoft Type Cover 3 with 0x07e2 product ID.
Signed-off-by: Donavan Lance <shvr@fedoraproject.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch enables the Saitek HID quirk for the mode button of the Mad Catz
R.A.T.5 gaming mouse by adding the same quirk that's been neeeded for
preivous versions.
[jikos@kernel.org: update changelog a little bit]
Signed-off-by: Harald Brinkmann <hbrinkmann@braincalibration.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like 0x8882 needs the same quirk than 0x8883.
Given that both devices claim they are "TPV OpticalTouchScreen" rename
the 0x8883 to add its PID in the #define.
Reported-by: Blaine Lee <blaine.j.lee@medtronic.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This gamepad advertise 5 absolute axis while 4 are actually used.
The second Z axis shows some garbage, so it has to be ignored by HID.
The first Z axis and the Rz one are actually Rx and Ry. Remap them.
We could also just remap and ignore the axis in .input_mapping(). I
went ahead with .report_fixup() first, so here it is.
Reported-by: Orivej Desh <orivej@gmx.fr>
Tested-by: Orivej Desh <orivej@gmx.fr>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull input fixes from Dmitry Torokhov:
"The main change is support for keyboards and touchpads found in 2015
editions of Macbooks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: zforce - don't overwrite the stack"
Input: bcm5974 - add support for the 2015 Macbook Pro
HID: apple: Add support for the 2015 Macbook Pro
Input: bcm5974 - prepare for a new trackpad generation
Input: synaptics - dump ext10 capabilities as well
Acer Aspire Switch 12 keyboard Chicony's controller reports too big usage
index on the 1st interface. The patch fixes the report. The work based on
solution from drivers/hid/hid-holtek-mouse.c
Bug report: https://bugzilla.kernel.org/show_bug.cgi?id=101721
Signed-off-by: Nicholas Kudriavtsev <nkudriavtsev@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Since this wheel is now available, and the USBID is listed on their website,
this patch adds it to allow the hid-lg4ff force feedback driver to find it.
I do not have this wheel to test with, but this should at least get it working
in emulation mode.
Note: There is probably more work required for adjust HID descriptor and handle
switching between emulation and native modes.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This patch adds keyboard support for MacbookPro12,1 as WELLSPRING9
(0x0272, 0x0273, 0x0274). The touchpad is handled in a separate
bcm5974 patch, as usual.
Tested-by: John Horan <knasher@gmail.com>
Tested-by: Jochen Radmacher <jradmacher@gmx.de>
Tested-by: Yang Hongyang <burnef@gmail.com>
Tested-by: Yen-Chin, Lee <coldnew.tw@gmail.com>
Tested-by: George Hilios <ghilios@gmail.com>
Tested-by: Janez Urevc <janez@janezurevc.name>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adding support for the Microsoft Surface 3 (non-pro) Type Cover.
The existing definitions and quirks are actually for the Surface
Pro 3 type covers. I've renamed the old constants to reflect that
they belong to the Surface Pro 3, and added a new constant and
matching code for the Surface 3.
Signed-off-by: Stephen Just <stephenjust@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Adding support for the Microsoft Surface Pro Power Cover.
Signed-off-by: Raimund Roth <raimundmroth@gmail.gom>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Removes Vernier Software & Technology devices from the ldusb
driver and the hid_ignore_list table of the usbhid driver in the
Linux tree. These devices will now be supported via the hidraw
driver.
A user space driver for these devices will be found in the
Go! Software Development Kit from Vernier at
http://www.vernier.com/downloads/software-development-kits/go-sdk/.
These devices are also be supported by the LabQuest2 standalone
interface shown at http://www.vernier.com/products/interfaces/labq2/
and the LoggerPro for Linux software shown at
http://www.vernier.com/downloads/logger-pro-linux/.
Signed-off-by: Dennis O'Brien <dennis.obrien@eqware.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I received a report from an user of following mouse which needs this quirk:
usb 1-1.6: USB disconnect, device number 58
usb 1-1.6: new low speed USB device number 59 using ehci_hcd
usb 1-1.6: New USB device found, idVendor=04f2, idProduct=1053
usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.6: Product: USB Optical Mouse
usb 1-1.6: Manufacturer: PixArt
usb 1-1.6: configuration #1 chosen from 1 choice
input: PixArt USB Optical Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input5887
generic-usb 0003:04F2:1053.16FE: input,hidraw2: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-0000:00:1a.0-1.6/input0
The quirk was tested by the reporter and it fixed the frequent disconnections etc.
[jkosina@suse.cz: reorder the position in hid-ids.h]
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Like other KVM switches, the Aten DVI KVM switch needs a quirk to avoid spewing
errors:
[791759.606542] usb 1-5.4: input irq status -75 received
[791759.614537] usb 1-5.4: input irq status -75 received
[791759.622542] usb 1-5.4: input irq status -75 received
Add it.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Once there were kernel drivers for some of the phidgets devices, and for
those kernel drivers to work the hid system needed exceptions. Now the
kernel drivers are long gone in favour of the user-space drivers.
The user-space drivers support many more phidget devices and uses libusb.
The udev rules set up permissions so that the kernel hid driver can be
unbound from libusb, as it does for many devices not in hid_ignore_list.
http://www.phidgets.com/docs/OS_-_Linux
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds the PID for the Sony motion controller to the hardware ID list.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This dock is used with the Thinkpad Helix 2 but suffers from an error
in the report descriptor where an usage max is 65535.
Add a report fixup for it and make the keyboard working.
Tested-by: Jonathan Oppenheim <lejono@gmail.com>
Tested-by: John Reid <owlman.lists@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The raphnet.net 4nes4snes and 2nes2snes multi-joystick adapters use a single
HID report descriptor with one report ID per controller. This has the effect
that the inputs of otherwise independent game controllers get packed in one
large joystick device.
With this patch each controller gets its own /dev/input/jsX device, which is
more natural and less confusing than having all inputs going to the same place.
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device exists with two device IDs instead of one as previously
believed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
During a stress test these mice kept dropping and reappearing
in runlevel 1 as opposed to 5.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse is also known under other IDs. It needs the quirk or will disconnect
in runlevel 1 or 3.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The linux kernel has supported the TiVo Slide remote control for some time, but
does not recognize the USB ID of the newer Slide Pro. This patch adds the
missing data structures so the newer remote will be recognized by the driver,
thereby allowing the TiVo, LiveTV, and Thumbs Up/Down buttons to be
mapped with a hwdb file.
Signed-off-by: Forest Wilkinson <web11.forest@tibit.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Microsoft Natural Wireless Ergonomic Keyboard 7000 has special My
Favorites 1..5 keys which are handled through a vendor-defined usage
page (0xff05).
Apply MS_ERGONOMY quirks handling to USB PID 0x071d (Microsoft Microsoft
2.4GHz Transceiver V1.0) so that the My Favorites 1..5 keys are reported
as KEY_F14..18 events.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=52841
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Genius PenSketch M912 digitizer tablet sends incorrect report descriptor by
default. This patch replaces it with a corrected one.
Signed-off-by: Milan Plzik <milan.plzik@gmail.com>
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Microchip Pick16F1454 is exported as a HID device and is used by for
example the Yepkit YKUSH three-port switchable USB hub. However, it is not an
actual HID-device. On the Yepkit, it is used to power up/down the ports on the
hub. The HID driver should ignore this device.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Have hid-rmi handle all of the Razer Blade HID devices that are part of the
composite USB device. This will allow hid-rmi to operate the touchpad in rmi
mode while passing events from the other devices to hid-input.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on code for the US Surface Type Cover 3
from commit be3b16341d
("HID: add support for MS Surface Pro 3 Type Cover"):
Signed-off-by: Alan Wu <alan.c.wu@gmail.com>
Tested-by: Karlis Dreizis <karlisdreizis@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
New Genius MousePen i608X devices have a new id 0x501a instead of the
old 0x5011 so add a new #define with "_2" appended and change required
places.
The remaining two checkpatch warnings about line length
being over 80 characters are present in the original files too and this
patch was made in the same style (no line break).
Just adding a new id and changing the required places should make the
new device work without any issues according to the bug report in the
following url.
This patch was made according to and fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=67111
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds force feedback support for BETOP USB game controllers.
These devices are mass produced in China.
Signed-off-by: Huang Bo <huangbobupt@163.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
VTL panels do not switch to the multitouch mode until the input mode
feature is read by the host. This should normally be done by
usbhid, but it looks like an other bug prevents usbhid to properly
retrieve the feature state. As a workaround, we force the reading of
the feature in mt_set_input_mode for such devices.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Mathieu Magnaudet <mathieu.magnaudet@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add vid/pid for the SMK branded third-party PS3 Bluetooth remote and enable
support in the hid-sony driver.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The touchscreen needs the same quirk as the other models.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Bryan Poling <poli0048@umn.edu>
CC: stable@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I have tested HID quirk for Saitek R.A.T.7 with my R.A.T. 9. It works fine for
me. Attached patch makes the necessary changes to use the quirk on the R.A.T.9
too, and necessary Kconfig changes too.
I have stylized the Kconfig option name to include Mad Catz in the option name,
as (at least some of) the devices are marketed under Mad Catz brand.
Signed-off-by: Ville Aakko <ville.aakko@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Yet another device that needs this quirk.
Reported-by: Tanguy de Baritault <tdebaritault@gmail.com>
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This version of the driver prevents Telephony pages which are not mapped as
Consumer Control applications AND are not on the Consumer Page from being
registered by the hid-input driver.
Signed-off-by: JD Cole <jd.cole@plantronics.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Logitech devices use a vendor protocol to communicate various
information with the device. This protocol is called HID++,
and an exerpt can be found here:
https://drive.google.com/folderview?id=0BxbRzx7vEV7eWmgwazJ3NUFfQ28&usp=shar
The main difficulty which is related to this protocol is that
it is a synchronous protocol using the input reports.
So when we want to get some information from the device, we need
to wait for a matching input report.
This driver introduce this capabilities to be able to support
the multitouch mode of the Logitech Wireless Touchpad T651
(the bluetooth one). The multitouch data is available directly
from the mouse input reports, and we just need to query the device
on connect about its caracteristics.
HID++ and the touchpad features has a specific reporting mode
which uses pure HID++ reports, but Logitech told us not to use
it for this specific device. During QA, they detected that
some bluetooth input reports where lost, and so the only supported
mode is the pointer mode.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Andrew de los Reyes <adlr@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device needs the quirk as well.
Tested-by: Kevin Fenzi <kevin@scrye.com>
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is a second mouse sharing the same vendor strings but different IDs.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse keeps disconnecting in runlevel 3. It needs the ALWAYS_POLL quirk.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The report descriptor for the HOLTEK USB ID 04d9:a0c2 (ETEKCITY Scroll
T-140 Gaming Mouse) is set to a very large amount of consumer usages
(2^16), exceeding HID_MAX_USAGES. Added id, bindings and comments for
the mouse, added to hid_have_special_driver, and reduced the usage and
logical maximums to 0x2fff, consistent with the other mice in the
category. Tested on the hardware.
Signed-off-by: John C. DeSilva <desilvjo@umich.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Enable the always-poll quirk for Elan Touchscreens found on some recent
Samsung laptops.
Without this quirk the device keeps disconnecting from the bus (and is
re-enumerated) unless opened (and kept open, should an input event
occur).
Note that while the device can be run-time suspended, the autosuspend
timeout must be high enough to allow the device to be polled at least
once before being suspended. Specifically, using autosuspend_delay_ms=0
will still cause the device to disconnect on input events.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds a seperate hid-penmount driver to work
around an issue with the HID report descriptor. The
descriptor does not contain the ContactID usage and as
result the touchscreen is represented as normal mouse
to the system.
This driver maps the button 0 emitted by the touchscreen
to BTN_TOUCH. This makes it possible to use touch events
in userspace.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Ignore Jabra GN9350E HID interface. USB audio is working nicely, but
registering as HID blocks USB mouse buttons. Since special userspace programs
are needed we will avoid attaching usbhid drivers in general.
Signed-off-by: Patrick Plattes <patrick@erdbeere.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for both ThinkPad Compact Bluetooth Keyboard with
TrackPoint and ThinkPad Compact USB Keyboard with TrackPoint.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use word "tablet" in identifiers and comments instead of referring to specific
Huion tablet model name, as the product ID is used by at least several tablet
models.
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I am using a USB keyborad that give me "usb_submit_urb(ctrl) failed: -1" error
when I plugin it. and I need to wait for 10s for this device to be ready.
By adding this quirks, the usb keyborad is usable right after plugin
Signed-off-by: Wangzhao Cai <microcaicai@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver adds support for USB controlled led panels that exists in
MSI GT683R laptop
Signed-off-by: Janne Kanniainen <janne.kanniainen@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
These device needs to be added to the quirks list with HID_QUIRK_NOGET,
otherwise they will reset upon receiving the get input report requests.
Signed-off-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added STM sensor hub new device id. Also added this new device
in HID_SENSOR_HUB_ENUM_QUIRK to fix report descriptors.
These devices uses old FW which uses logical 0 as minimum.
In these, HID reports are not using proper collection classes.
So we need to fix report descriptors,for such devices. This
will not have any impact, if the FW uses logical 1 as minimum.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Subramony Sesha <subramony.sesha@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device which identifies itself as a "USB Keykoard" (no typo) with VID:PID
1a2c:0023 does not seem to be handling the reports initialization very well.
This results in a "usb_submit_urb(ctrl) failed: -1" message from the kernel
when connected, and a delay before its initialization. This patch adds the
quirk for this device, which causes the delay to disappear.
[jkosina@suse.cz: remove superfluous comment and fix ordering]
Signed-off-by: Daniel Kamil Kozar <dkk089@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the Microsoft Surface Pro 2 Type/Touch and default device hardware ID's
Set report quirk for the device in hid-sensor-hub
Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some saitek mice implement a tristate button (for switching button mappings in
the original driver) by keeping one of three (non-physical)
buttons constantly pressed.
This breaks X and probably other userspace software.
This patch implements a quirk for the R.A.T.7 and M.M.O.7, tracking the mode
and generating presses of a single button if it changes. Also the missing
release event is generated instantly.
Signed-off-by: Harald Brinkmann <hbrinkmann@braincalibration.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The sensor hub in Lenovo Yogas needs the enumeration quirk. I've been running
the patch for over a month with no problems, whereas the unpatched drivers
reliably mis-initialized the sensors.
Signed-off-by: Peter F. Patel-Schneider <pfpschneider@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This touchpad seriously dislikes init reports, not only timeing out, but
also refusing to work after this.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Vincent Fortier <th0ma7@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
They need to have the class SERIAL.
Note: it is a Win 7 panel, not Win 8 certified.
Signed-off-by: Tomas Sokorai <tsokorai@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 117309c51d.
The MS Surface Pro 2 has an USB composite device with 3 interfaces
- interface 0 - sensor hub
- interface 1 - wacom digitizer
- interface 2 - the keyboard cover, if one is attached
This USB composite device changes it product id dependent on if and which
keyboard cover is attached. Adding the covers to hid_have_special_driver
prevents loading the right hid drivers for the other two interfaces, all 3
get loaded with hid-microsoft. We don't even need hid-microsoft for the
keyboards. We have to revert this to load the right hid modules for each
interface.
CC: stable@vger.kernel.org # kernel 3.14 only
Signed-off-by: Derya <derya.kiran@yahoo.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Just like some of the other laptops/tablets on the market with ultrabook
sensors, the ThinkPad Helix's sensor hub requires a special quirk in
order for it to power on properly. Without it the sensors are detected
by the kernel and set up as usual, but they won't output any data. This
will also fix the sensors on any other laptops with the same model of
sensor hub.
Signed-off-by: Stephen Chandler Paul <thatslyude@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID updates from Jiri Kosina:
- substantial cleanup of the generic and transport layers, in the
direction of an ultimate goal of making struct hid_device completely
transport independent, by Benjamin Tissoires
- cp2112 driver from David Barksdale
- a lot of fixes and new hardware support (Dualshock 4) to hid-sony
driver, by Frank Praznik
- support for Win 8.1 multitouch protocol by Andrew Duggan
- other smaller fixes / device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (75 commits)
HID: sony: fix force feedback mismerge
HID: sony: Set the quriks flag for Bluetooth controllers
HID: sony: Fix Sixaxis cable state detection
HID: uhid: Add UHID_CREATE2 + UHID_INPUT2
HID: hyperv: fix _raw_request() prototype
HID: hyperv: Implement a stub raw_request() entry point
HID: hid-sensor-hub: fix sleeping function called from invalid context
HID: multitouch: add support for Win 8.1 multitouch touchpads
HID: remove hid_output_raw_report transport implementations
HID: sony: do not rely on hid_output_raw_report
HID: cp2112: remove the last hid_output_raw_report() call
HID: cp2112: remove various hid_out_raw_report calls
HID: multitouch: add support of other generic collections in hid-mt
HID: multitouch: remove pen special handling
HID: multitouch: remove registered devices with default behavior
HID: hidp: Add a comment that some devices depend on the current behavior of uniq
HID: sony: Prevent duplicate controller connections.
HID: sony: Perform a boundry check on the sixaxis battery level index.
HID: sony: Fix work queue issues
HID: sony: Fix multi-line comment styling
...
The ANTON Touch Pad is a device which can switch from a multitouch
touchpad to a mouse. It thus presents several generic collections which
are currently ignored by hid-multitouch. Enable them by not ignoring
them in mt_input_mapping.
Adding also a suffix for them depending on their application.
Reported-by: Edel Maks <edelmaks@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID update from Jiri Kosina:
- fixes for several bugs in incorrect allocations of buffers by David
Herrmann and Benjamin Tissoires.
- support for a few new device IDs by Archana Patni, Benjamin
Tissoires, Huei-Horng Yo, Reyad Attiyat and Yufeng Shen
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hyperv: make sure input buffer is big enough
HID: Bluetooth: hidp: make sure input buffers are big enough
HID: hid-sensor-hub: quirk for STM Sensor hub
HID: apple: add Apple wireless keyboard 2011 JIS model support
HID: fix buffer allocations
HID: multitouch: add FocalTech FTxxxx support
HID: microsoft: Add ID's for Surface Type/Touch Cover 2
HID: usbhid: quirk for CY-TM75 75 inch Touch Overlay
This patch adds support for the Silicon Labs CP2112 "Single-Chip HID USB to
SMBus Master Bridge."
This is a HID device driver which registers as an i2c adapter and gpiochip to
expose these functions of the CP2112. The customizable USB descriptor fields
are exposed as sysfs attributes. The SMBus byte-read, byte-data-read/write,
and word-data-read transfer modes have been tested by talking to an i2c
sensor. The GPIO functions and USB descriptor field programming have also
been tested.
Signed-off-by: David Barksdale <dbarksdale@uplogix.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added STM sensor hub vendor id in HID_SENSOR_HUB_ENUM_QUIRK to
fix report descriptors. These devices uses old FW which uses
logical 0 as minimum. In these, HID reports are not using proper
collection classes. So we need to fix report descriptors,for
such devices. This will not have any impact, if the FW uses
logical 1 as minimum.
We look for usage id for "power and report state", and modify
logical minimum value to 1.
This is a follow-up patch to commit id 875e36f8.
Signed-off-by: Archana Patni <archana.patni@linux.intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The "Webmail Notifier" is a USB controlled LED that appears as a HID
device. When trying to change the LED via hidraw it returns malformed
reports. As "usbled" supports it, we blacklist it in usbhid.
Signed-off-by: Christian Vogel <vogelchr@vogel.cx>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Apple wireless keyboard 2011 JIS model (05ac:0257).
Signed-off-by: Huei-Horng Yo <hiroshi@ghostsinthelab.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Microsoft Office keyboard has a scrollwheel as well as some special keys
above the keypad which are handled through the custom MS usage page, this
commit adds support for these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull media updates from Mauro Carvalho Chehab:
- a new jpeg codec driver for Samsung Exynos (jpeg-hw-exynos4)
- a new dvb frontend for ds2103 chipset (m88ds2103)
- a new sensor driver for Samsung S5K5BAF UXGA (s5k5baf)
- new drivers for R-Car VSP1
- a new radio driver: radio-raremono
- a new tuner driver for ts2022 chipset (m88ts2022)
- the analog part of em28xx is now a separate module that only
load/runs if the device is not a pure digital TV device
- added a staging driver for bcm2048 radio devices
- the omap 2 video driver (omap24xx) was moved to staging. This driver
is for an old hardware and uses a deprecated Kernel internal API. If
nobody cares enough to fix it, it would be removed on a couple Kernel
releases
- the sn9c102 driver was moved to staging. This driver was replaced by
gspca, and disabled on some distros, as almost all devices are known
to work properly with gspca. It should be removed from kernel on a
couple Kernel releases
- lots of driver fixes, improvements and cleanups
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (421 commits)
[media] media: v4l2-dev: fix video device index assignment
[media] rc-core: reuse device numbers
[media] em28xx-cards: properly initialize the device bitmap
[media] Staging: media: Fix line length exceeding 80 characters in as102_drv.c
[media] Staging: media: Fix line length exceeding 80 characters in as102_fe.c
[media] Staging: media: Fix quoted string split across line in as102_fe.c
[media] media: st-rc: Add reset support
[media] m2m-deinterlace: fix allocated struct type
[media] radio-usb-si4713: fix sparse non static symbol warnings
[media] em28xx-audio: remove needless check before usb_free_coherent()
[media] au0828: Fix sparse non static symbol warning
Revert "[media] go7007-usb: only use go->dev after allocated"
[media] em28xx-audio: provide an error code when URB submit fails
[media] em28xx: fix check for audio only usb interfaces when changing the usb alternate setting
[media] em28xx: fix usb alternate setting for analog and digital video endpoints > 0
[media] em28xx: make 'em28xx_ctrl_ops' static
em28xx-alsa: Fix error patch for init/fini
[media] em28xx-audio: flush work at .fini
[media] drxk: remove the option to load firmware asynchronously
[media] em28xx: adjust period size at runtime
...
This is a Win7 device which does not work correctly with the default
settings (not the previous default BT).
However, the quirk ALWAYS_TRUE makes it working like a charm.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Microsoft Surface Type/Touch cover 2 devices have the flag HID_DG_CONTACTID
in their reports.This causes the device to bind to the hid-multitouch driver,
which doesn't handle generic keyboard/mouse input events. The patch adds
the hardware id's of the device to hid-microsoft and to the HID special
driver array, which makes the device get handled by hid-generic/hid-input
properly.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=64811
Singed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Reviewed-by: Benjamin Tissoires<benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This addresses regression caused by commit id "751d17e23a9f7"
iio: hid-sensors: Fix power and report state.
This commit removed a quirk, to change the enumeration base
to 1 from 0 based on an CONFIG paramter. There was objection to
add more changes under this quirk, instead suggested to add an
HID quirk. But there is no easy way to add HID qurik as the
reports are not properly using collection class.
The solution was to use logical minimum, which is a correct way.
There were changes done in firmware to address this.
Unfortunately some devices, still use old FW and can't be upgraded
to newer version on Linux devices as there is no FW upgrade tool
available for Linux devices. So we need to fix report descriptors,
for such devices. This will not have any impact, if the FW uses
logical 1 as minimum.
In this patch we look for usage id for "power and report state", and
modify logical minimum value to 1.
Background on enum:
In the original HID sensor hub firmwares all Named array enums were
to 0-based. But the most recent hub implemented as 1-based,
because of the implementation by one of the major OS vendor.
Using logical minimum for the field as the base of enum. So we add
logical minimum to the selector values before setting those fields.
Some sensor hub FWs already changed logical minimum from 0 to 1
to reflect this and hope every other vendor will follow.
There is no easy way to add a common HID quirk for NAry elements,
even if the standard specifies these field as NAry, the collection
used to describe selectors is still just "logical".
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds the Dualshock 4 to the HID device list and enables force-feedback.
Adds a Dualshock 4 specific worker function since the Dualshock 4 needs a
different report than the Sixaxis.
The right motor in the Dualshock 4 is variable so the full rumble value
is now passed to the worker function and clamped there if necessary.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Si4713 development board contains a Si4713 FM transmitter chip
and is handled by the radio-usb-si4713 driver.
The board reports itself as (10c4:8244) Cygnal Integrated Products, Inc.
and misidentifies itself as a HID device in its USB interface descriptor.
This patch ignores this device as an HID device and hence loads the custom driver.
Signed-off-by: Dinesh Ram <dinesh.ram@cern.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I have two Logitech Dual Action gamepads, both have same Vendor/Device id pair.
Newest gamepad (A) can switch between old mode (HID) and XBox gamepad emulation
mode. Old gamepad (B) can only work in HID mode. In HID mode gamepad A sends
many EPIPE errors during initialization and was disconnected immediately after
connect to usb port. It works fine in Win and Mac. After adding NOGET quirk in
driver, it was working properly. Gamepad B works fine before and after
changes. I tested both gamepads with 3.8.0 and 3.11.6 kernels with modified
driver. Follow patch can apply for current git kernel version. I can send pcap
log from usb bus with both gamepads or any other additional information if it
is needed
Signed-off-by: Vitaly Katraew <zawullon@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Synaptics HD touchscreen(06cb:1ac3) to no init report quirk
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Synaptics HD touchscreen(06cb:0ac3) to no init report quirk.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
USB_VENDOR_ID_SIS and USB_VENDOR_ID_SIS2_TOUCH are identical,
so refine the code and merge the quirks.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Genius Manticore Keyboard presents the same problem in its report
descriptors than Genius Gila Gaming Mouse and Genius Imperator Keyboard.
Use the same fixup.
Reported-and-tested-by: Adam Kulagowski <fidor@fidor.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds PID VID to support for the Wistron Inc. Optical touch panel.
Signed-off-by: KaiChung Cheng <kenny_cheng@wistron.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 86b84167d4 as it introduced a
VID/PID conflict with its original owner: hid-wiimote got
hid:b0005g*v0000054Cp00000306 added but hid-sony already has this id for the
PS3 Remote (and the ID is oficically assigned to Sony).
Revert the commit to avoid hid-sony regression. David is working on a
bluez patch to force proper ID on the wiimote.
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Reported-by: Michel Kraus <mksolpa@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added support for 3 keyboards with increasing illumination capabilities
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added id, bindings and comments for Holtek USB ID 04d9:a072
LEETGION Hellion Gaming mouse to use the same corrections of the report
descriptor as Holtek 04d9:a067. As the mouse exceed HID_MAX_USAGES at the
same offsets in the reported descriptor.
Tested on the hardware.
Signed-off-by: Anders F. U. Kiær <ablacksheep@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The LEGO-wiimote uses a different VID than the Nintendo ID. The device is
technically the same so add the ID.
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
BugLink: http://bugs.launchpad.net/bugs/1180881
This device needs to be added to the quirks list with HID_QUIRK_NO_INIT_REPORTS,
otherwise it causes 10 seconds timeout during report initialization.
[12431.828467] hid-multitouch 0003:0457:1013.0475: usb_submit_urb(ctrl) failed: -1
[12431.828507] hid-multitouch 0003:0457:1013.0475: timeout initializing reports
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
BugLink: http://bugs.launchpad.net/bugs/1180881
Synaptics large touchscreen doesn't support some of the report request
while initializing. The unspoorted request will make the device unreachable,
and will lead to the following usb_submit_urb() function call timeout.
So, add the IDs into HID_QUIRK_NO_INIT_REPORTS quirk.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add USB IDs for Logitech Formula Vibration Feedback Wheel (046d:ca04).
The lg2ff force feedback subdriver is used for vibration and
HID_GD_MULTIAXIS is set to avoid deadzone like other Logitech wheels.
Kconfig description etc are also updated accordingly.
Signed-off-by: Elias Vanderstuyft <Elias.vds@gmail.com>
[anssi.hannula@iki.fi: added description and CCs]
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
GeneralTouch products should use the quirk SLOT_IS_CONTACTID
instead of SLOT_IS_CONTACTNUMBER.
Adding PIDs 0101,e100,0102,0106,010a from the new products.
Tested on new and older products by GeneralTouch engineers.
Signed-off-by: Luosong <android@generaltouch.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added id, bindings and comments for Holtek USB ID 04d9:a081 SHARKOON
DarkGlider Gaming mouse to use the same corrections of the report
descriptor as Holtek 04d9:a04a. As the mouse exceed HID_MAX_USAGES
at the same offsets in the reported descriptor.
Tested on the hardware.
Signed-off-by: Anders F. U. Kiær <ablacksheep@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A recent patch (9d9a04ee) added support for the new machine, but got
the sequence of USB ids wrong. Reports from both Ian and Linus T show
that the 0x0291 id is for ISO, not ANSI, which should have the missing
number 0x0290. This patchs moves the three numbers accordingly, fixing
the problem.
Reported-and-tested-by: Ian Munsie <darkstarsword@gmail.com>
Tested-by: Linus G Thiel <linus@hanssonlarsson.se>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Sync with Linus' tree to be able to apply fixup patch on top
of 9d9a04ee75 ("HID: apple: Add support for the 2013 Macbook Air")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
KonePureOptical is a KonePure with different sensor.
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DuoSense touchscreen device causes a 10 second timeout. This fix
removes the delay.
Signed-off-by: Vasily Titskiy <qehgt0@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The driver currently only supports the Dual Arcade controller.
It fixes the negative axis event values (the devices sends -2) to match the
logical axis minimum of the HID report descriptor (the report announces -1).
It is needed because hid-input discards out of bounds values.
Signed-off-by: Olivier Scherler <oscherler@ithink.ch>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Genius Gx Imperator Keyboard presents the same problem in its report
descriptors than Genius Gila Gaming Mouse.
Use the same fixup for both.
Fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=928561
Reported-and-tested-by: Honza Brazdil <jbrazdil@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull input updates from Dmitry Torokhov:
"First round of updates for the input subsystem.
You will get a new touchsreen driver for Cypress 4th generation
devices, a driver for a special controller implementing PS/2 protocol
in OLPC devices, and a driver for power key for SiRFprimaII PWRC.
HID and bcm5497 now support for the 2013 MacBook Air.
EVIOCGKEY and the rest of evdev ioctls now flush events of matching
type from the client's event queue so that clients can be sure any
events received after issuing EVIOCG* ioctl are new events.
And a host of cleanups and improvements in other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (87 commits)
Input: cyttsp4 - kfree xfer_buf on error path in probe()
Input: tps6507x-ts - select INPUT_POLLDEV
Input: bcm5974 - add support for the 2013 MacBook Air
HID: apple: Add support for the 2013 Macbook Air
Input: cyttsp4 - leak on error path in probe()
Input: cyttsp4 - silence NULL dereference warning
Input: cyttsp4 - silence shift wrap warning
Input: tps6507x-ts - convert to polled input device infrastructure
ARM: davinci: da850-evm: remove vref from touchscreen platform data
Input: cyttsp4 - SPI driver for Cypress TMA4XX touchscreen devices
Input: cyttsp4 - I2C driver for Cypress TMA4XX touchscreen devices
Input: cyttsp4 - add core driver for Cypress TMA4XX touchscreen devices
Input: cyttsp - I2C driver split into two modules
Input: add OLPC AP-SP driver
Input: nspire-keypad - remove redundant dev_err call in nspire_keypad_probe()
Input: tps6507x-ts - remove vref from platform data
Input: tps6507x-ts - use bool for booleans
Input: tps6507x-ts - remove bogus unreachable code
Input: samsung-keypad - let device core setup the default pin configuration
Input: wacom_i2c - implement hovering capability
...
Trent Lloyd