The AHCI driver code stops and starts port DMA engines at will
without considering the power state of the particular port. The
AHCI specification isn't very clear on how to handle this scenario,
leaving implementation open to interpretation.
Broadcom's STB SATA host controller is unable to handle port DMA
controller restarts when the port in question is in low power mode.
When a port enters partial or slumber mode, its PHY is powered down.
When a controller restart is requested, the controller's internal
state machine expects the PHY to be brought back up by software which
never happens in this case, resulting in failures.
To avoid this situation, logic is added to manually wake up the port
just before its DMA engine is stopped, if the port happens to be in
a low power state. HBA initiated power management ensures that the port
eventually returns to its configured low power state, when the link is
idle (as per the conditions listed in the spec). A new host flag is also
added to ensure this logic is only exercised for hosts with the above
limitation.
tj: Formatting changes.
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The link resume logic uses a 200msec delay while debouncing
the SControl register. The rationale behind that delay is
to accommodate some PHYs that behave badly if their SStatus/
SControl registers are pounded immediately on resume.
The Broadcom STB SATA PHY does not seem to have this issue.
This patch introduces a new link flag that allows platforms
to skip the debounce delay if it isn't needed.
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Broadcom STB SATA host controller does not support device
initiated power management. Disable support for this feature
so the driver never sends SETFEATURES commands to the device
to enable/disable DIPM.
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Enable support for ALPM in the host controller's capabilities
register. Also adjust the PLL timeout to give it enough time
to lock when the port exits slumber mode.
tj: minor style updates
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The BCM7xxx ARM-based and MIPS-based platforms share a similar hardware
block for AHCI SATA3.
This new compatible string, "brcm,bcm7425-ahci", may be used for most
MIPS-based platforms of 40nm process technology.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Remove unused definitions, and this is to avoid confusion with MIPS-based
platforms.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Whereas ARM-based platforms have four phy interface registers and
information, the MIPS-based platforms have only three registers, and
there are no information and documentation. In the original BSP, It
using "strict-ahci" did not control these registers.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
The most MIPS-based platforms need to disable NCQ while have the NCQ
capability in HOST_CAP, and several ARM-based platforms (eg. BCM7349A0,
BCM7445A0, BCM7445B0) need to disable too.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not
for other symbols such as __BIG_ENDIAN that is provided directly by
the compiler.
Switch to use CONFIG_CPU_BIG_ENDIAN instead of __BIG_ENDIAN.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
When CONFIG_PM_SLEEP is disabled, brcm_ahci_{suspend,resume} are not
used, which causes such a build warning to occur:
CC drivers/ata/ahci_brcmstb.o
drivers/ata/ahci_brcmstb.c:212:12: warning: 'brcm_ahci_suspend' defined
but not used [-Wunused-function]
static int brcm_ahci_suspend(struct device *dev)
^
drivers/ata/ahci_brcmstb.c:224:12: warning: 'brcm_ahci_resume' defined
but not used [-Wunused-function]
static int brcm_ahci_resume(struct device *dev)
^
LD drivers/ata/built-in.o
Fixes: 766a2d9796 ("ata: add Broadcom AHCI SATA3 driver for STB chips")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pretty straightforward driver, using the nice library-ization of the
generic ahci_platform driver.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Danesh Petigara