The a2mp_send function is a local function and so do not export it
and make it static.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The amp_mgr_lookup_by_state function does not need to be exported. So
just move it to a different location and make it static.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no reason to have amp_mgr_list and amp_mgr_list_lock exported
from a2mp.c and thus make both of them static.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The A2MP_FEAT_EXT declaration has a single user in a2mp.c and thus
just move it there.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This callback allows a vendor to send the vendor specific commands
before cloing the hci interface.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If user space is trying to pair on not enabled transport
MGMT_STATUS_REJECT will be returned.
If user space is trying to pair on transport which controller does not
support, MGMT_STATUS_NOT_SUPPORTED will be returned.
Having separate error code for that scenario might be useful for
debugging at least.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With this patch -EOPNOTSUPP will be returned by hci_connect_acl for LE
only controllers. If it is dual device with disabled BREDR -ECONNREFUSED
will be returned
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Kernel gives possibility to enable/disable LE host support.
There is flag HCI_LE_ENABLED which is set when this support is enabled
and some parts of the code checks this flag e.g. SMP
However it is still possible to make LE connection if LE Host support is
disabled, what might be confused for remote device.
This patch makes sure that kernel will not send HCI LE Create Connection
if LE HOST support is not enabled.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bnep_get_device function may be triggered by an ioctl just after a
connection has gone down. In such a case the respective L2CAP chan->conn
pointer will get set to NULL (by l2cap_chan_del). This patch adds a
missing NULL check for this case in the bnep_get_device() function.
Reported-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This extended return parameters struct conflicts with the new Read Local
OOB Extended Data command definition. To avoid the conflict simply
rename the old "extended" version to the normal one and update the code
appropriately to take into account the two possible response PDU sizes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using LE_SCAN_FILTER_DUP_ENABLE, some controllers would send
advertising report from each LE device only once. That means that we
don't get any updates on RSSI value, and makes Service Discovery very
slow. This patch adds restarting scan when in Service Discovery, and
device with filtered uuid is found, but it's not in RSSI range to send
event yet. This way if device moves into range, we will quickly get RSSI
update.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently there is no way to restart le scan, and it's needed in
service scan method. The way it work: it disable, and then enable le
scan on controller.
During the restart, we must remember when the scan was started, and
it's duration, to later re-schedule the le_scan_disable work, that was
stopped during the stop scan phase.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using Secure Connections Only mode, then only P-256 OOB data is
valid and should be provided. In case userspace provides P-192 and P-256
OOB data, then the P-192 values will be set to zero. However the present
value of the IO capability exchange still mentioned that both values
would be available. Fix this by telling the controller clearly that only
the P-256 OOB data is present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For debugging purposes it is good to know which OOB data is actually
currently loaded for each controller. So expose that list via debugfs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Hardware Error event is send by the controller, the Bluetooth
core stores the error code. Expose it via debugfs so it can be retrieved
later on.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To allow easier debugging when debug keys are generated, provide debugfs
entry for checking the setting of debug keys usage.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the HCI Write Simple Pairing Debug Mode command has been issued,
the result needs to be tracked and stored. The hdev->ssp_debug_mode
variable is already present, but was never updated when the mode in
the controller was actually changed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The value of the ssp_debug_mode should be accessible via debugfs to be
able to determine if a BR/EDR controller generates debugs keys or not.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case the remote only provided P-192 or P-256 data for OOB pairing,
then make sure that the data value pointers are correctly set. That way
the core can provide correct information when remote OOB data present
information have to be communicated.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Before setting the OOB data present flag with SMP pairing, check the
newly introduced present tracking that actual OOB data values have
been provided. The existence of remote OOB data structure does not
actually mean that the correct data values are available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When BR/EDR Secure Connections has been enabled, the OOB data present
value can take 2 additional values. The host has to clearly provide
details about if P-192 OOB data, P-256 OOB data or a combination of
P-192 and P-256 OOB data is present.
In case BR/EDR Secure Connections is not enabled or not supported,
then check that P-192 OOB data is actually present and return the
correct value based on that.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of doing complex calculation every time the OOB data is used,
just calculate the OOB data present value and store it with the OOB
data raw values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The smp_unregister() function needs to be called every time the
controller is powered down. There are multiple entry points when
this can happen. One is "hciconfig hci0 reset" which will throw
a WARN_ON when LE support has been enabled.
[ 78.564620] WARNING: CPU: 0 PID: 148 at net/bluetooth/smp.c:3075 smp_register+0xf1/0x170()
[ 78.564622] Modules linked in:
[ 78.564628] CPU: 0 PID: 148 Comm: kworker/u3:1 Not tainted 3.19.0-rc4-devel+ #404
[ 78.564629] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
[ 78.564635] Workqueue: hci0 hci_rx_work
[ 78.564638] ffffffff81b4a7a2 ffff88001cb2fb38 ffffffff8161d881 0000000080000000
[ 78.564642] 0000000000000000 ffff88001cb2fb78 ffffffff8103b870 696e55206e6f6f6d
[ 78.564645] ffff88001d965000 0000000000000000 0000000000000000 ffff88001d965000
[ 78.564648] Call Trace:
[ 78.564655] [<ffffffff8161d881>] dump_stack+0x4f/0x7b
[ 78.564662] [<ffffffff8103b870>] warn_slowpath_common+0x80/0xc0
[ 78.564667] [<ffffffff81544b00>] ? add_uuid+0x1f0/0x1f0
[ 78.564671] [<ffffffff8103b955>] warn_slowpath_null+0x15/0x20
[ 78.564674] [<ffffffff81562d81>] smp_register+0xf1/0x170
[ 78.564680] [<ffffffff81081236>] ? lock_timer_base.isra.30+0x26/0x50
[ 78.564683] [<ffffffff81544bf0>] powered_complete+0xf0/0x120
[ 78.564688] [<ffffffff8152e622>] hci_req_cmd_complete+0x82/0x260
[ 78.564692] [<ffffffff8153554f>] hci_cmd_complete_evt+0x6cf/0x2e20
[ 78.564697] [<ffffffff81623e43>] ? _raw_spin_unlock_irqrestore+0x13/0x30
[ 78.564701] [<ffffffff8106b0af>] ? __wake_up_sync_key+0x4f/0x60
[ 78.564705] [<ffffffff8153a2ab>] hci_event_packet+0xbcb/0x2e70
[ 78.564709] [<ffffffff814094d3>] ? skb_release_all+0x23/0x30
[ 78.564711] [<ffffffff81409529>] ? kfree_skb+0x29/0x40
[ 78.564715] [<ffffffff815296c8>] hci_rx_work+0x1c8/0x3f0
[ 78.564719] [<ffffffff8105bd91>] ? get_parent_ip+0x11/0x50
[ 78.564722] [<ffffffff8105be25>] ? preempt_count_add+0x55/0xb0
[ 78.564727] [<ffffffff8104f65f>] process_one_work+0x12f/0x360
[ 78.564731] [<ffffffff8104ff9b>] worker_thread+0x6b/0x4b0
[ 78.564735] [<ffffffff8104ff30>] ? cancel_delayed_work_sync+0x10/0x10
[ 78.564738] [<ffffffff810542fa>] kthread+0xea/0x100
[ 78.564742] [<ffffffff81620000>] ? __schedule+0x3e0/0x980
[ 78.564745] [<ffffffff81054210>] ? kthread_create_on_node+0x180/0x180
[ 78.564749] [<ffffffff816246ec>] ret_from_fork+0x7c/0xb0
[ 78.564752] [<ffffffff81054210>] ? kthread_create_on_node+0x180/0x180
[ 78.564755] ---[ end trace 8b0d943af76d3736 ]---
This warning is not critical and has only been placed in the code to
actually catch this exact situation. To avoid triggering it move
the smp_unregister() into hci_dev_do_close() which will now also
take care of remove the SMP channel. It is safe to call this function
since it only remove the channel if it has been previously registered.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When receiving a HCI Hardware Error event, the controller should be
assumed to be non-functional until issuing a HCI Reset command.
The Bluetooth hardware errors are vendor specific and so add a
new hdev->hw_error callback that drivers can provide to run extra
code to handle the hardware error.
After completing the vendor specific error handling perform a full
reset of the Bluetooth stack by closing and re-opening the transport.
Based-on-patch-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Split the hci_dev_reset ioctl handling into using hci_dev_do_reset
helper function. Similar to what has been done with hci_dev_do_open
and hci_dev_do_close.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The discovery state should be set to stopped when the HCI device is
powered off. This patch adds the appropriate call to the
hci_discovery_set_state() function from hci_dev_do_close() which is
responsible for the power-off procedure.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When HCI_Reset is issued the discovery state is assumed to be stopped.
The hci_cc_reset() handler was trying to set the state but it was doing
it without using the hci_discovery_set_state() function. Because of this
e.g. the mgmt Discovering event could go without being sent. This patch
fixes the code to use the hci_discovery_set_state() function instead of
just blindly setting the state value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's a check in set_secure_conn() that's supposed to ensure that SSP
is enabled before we try to request the controller to enable SC (since
SSP is a pre-requisite for it). However, this check only makes sense for
controllers actually supporting BR/EDR SC. If we have a 4.0 controller
we're only interested in the LE part of SC and should therefore not be
requiring SSP to be enabled. This patch adds an additional condition to
check for lmp_sc_capable(hdev) before requiring SSP to be enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If Secure Connections Only mode has been enabled, the it is important
to check that OOB data for P-256 values is provided. In case it is not,
then tell the remote side that no OOB data is present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When replying to the IO capability request for Secure Simple Pairing and
Secure Connections, the OOB data present fields needs to set. Instead of
making the calculation inline, split this into a separate helper
function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When Secure Connections Only mode has been enabled and remote OOB data
is requested, then only provide P-256 hash and randomizer vaulues. The
fields for P-192 hash and randomizer should be set to zero.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Until legacy SMP OOB pairing is implemented user space should be given a
clear error when trying to use it. This patch adds a corresponding check
to the Add Remote OOB Data handler function which returns "invalid
parameters" if non-zero Rand192 or Hash192 parameters were given for an
LE address.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
l2cap/rfcomm/sco_sock_accept() are wait loops which may acquire
sleeping locks. Since both wait loops and sleeping locks use
task_struct.state to sleep and wake, the nested sleeping locks
destroy the wait loop state.
Use the newly-minted wait_woken() and DEFINE_WAIT_FUNC() for the
wait loop. DEFINE_WAIT_FUNC() allows an alternate wake function
to be specified; in this case, the predefined scheduler function,
woken_wake_function(). This wait construct ensures wakeups will
not be missed without requiring the wait loop to set the
task state before condition evaluation. How this works:
CPU 0 | CPU 1
|
| is <condition> set?
| no
set <condition> |
|
wake_up_interruptible |
woken_wake_function |
set WQ_FLAG_WOKEN |
try_to_wake_up |
| wait_woken
| set TASK_INTERRUPTIBLE
| WQ_FLAG_WOKEN? yes
| set TASK_RUNNING
|
| - loop -
|
| is <condition> set?
| yes - exit wait loop
Fixes "do not call blocking ops when !TASK_RUNNING" warnings
in l2cap_sock_accept(), rfcomm_sock_accept() and sco_sock_accept().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch converts the Set Secure Connection HCI handling to use a HCI
request instead of using a hard-coded callback in hci_event.c. This e.g.
ensures that we don't clear the flags incorrectly if something goes
wrong with the power up process (not related to a mgmt Set SC command).
The code can also be simplified a bit since only one pending Set SC
command is allowed, i.e. mgmt_pending_foreach usage is not needed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Add Remote OOB Data mgmt command should allow data to be passed for
LE as well. This patch removes a left-over check for BDADDR_BREDR that
should not be there anymore.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Before doing any other verifications, the add_remote_oob_data function
should first check that the given address is valid. This patch adds such
a missing check to the beginning of the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When BR/EDR is supported by a controller, then it is required to enable
Secure Simple Pairing first before enabling the Secure Connections
feature.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a powered on dual-mode controller has been configured to operate
as LE only with secure connections, then the BR/EDR side of things can
not be switched back on. Do reconfigure the controller it first needs
to be powered down.
The secure connections feature is implemented in the BR/EDR controller
while for LE it is implemented in the host. So explicitly forbid such
a transaction to avoid inconsistent states.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BR/EDR Secure Connections feature should only be enabled when the
Secure Simple Pairing mode has been enabled first. However since secure
connections is feature that is valid for BR/EDR and LE, this needs
special handling.
When enabling secure connections on a LE only configured controller,
thent the BR/EDR side should not be enabled in the controller. This
patches makes the BR/EDR Secure Connections feature depending on
enabling Secure Simple Pairing mode first.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Start Discovery was reporting 0 RSSI for invalid RSSI only for
BR/EDR devices. LE devices were reported with RSSI 127.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 3.19+
Remove the function hci_conn_change_link_key() that is not used anywhere.
This was partially found by using a static code analysis program called
cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the SMP channels have been already registered, then print out a
clear WARN_ON message that something went wrong. Also unregister the
existing channels in this case before trying to register new ones.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The comparing of chan->src should always be done against the local
identity address, represented by hcon->src and hcon->src_type. This
patch modifies l2cap_global_fixed_chan() to take the full hci_conn so
that we can easily compare against hcon->src and hcon->src_type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current bdaddr_type() usage in l2cap_core.c is a bit funny in that
it's always passed a hci_conn + a hci_conn member. Because of this only
the hci_conn is really needed. Since the second parameter is always
either hcon->src_type or hcon->dst type this patch adds two helper
functions for each purpose: bdaddr_src_type() and bdaddr_dst_type().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the controller gets powered on via the management interface, then
register the supported SMP channels. There is no point in registering
these channels earlier since it is not know what identity address the
controller is going to operate with.
When powering down a controller unregister all SMP channels. This is
required since a powered down controller is allowed to change its
identity address.
In addition the SMP channels are only available when the controller
is powered via the management interface. When using legacy ioctl, then
Bluetooth Low Energy is not supported and registering kernel side SMP
integration may actually cause confusion.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When LE features are not supported, then do not bother registering any
kind of SMP channel.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The source address and source address type of the LE SMP channel can
either be the public address of the controller or the static random
address configured by the host.
Right now the public address is used for the LE SMP channel and
obviously that is not correct if the controller operates with the
configured static random address.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For dual-mode controllers it is possible to disable BR/EDR and operate
as LE single mode controllers with a static random address. If that is
the case, then refuse switching BR/EDR back on after the controller has
been powered.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The devices address types are BR/EDR Public, LE Public and LE Random and
any of these three is valid for L2CAP connections. So show the correct
type in the debugfs list.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann