Add comment about the meaning of the fixed JPEG header bytes used to
create each image.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The length check in reg_w_var() function is because the buffer contents
is copied to gspca_dev->usb_buf which has the size of USB_BUF_SZ bytes as
defined in drivers/media/video/gspca/gspca.h. Replace the number with
symbol for better readability and maintainability.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert tda18271_rf_tracking_filter_cal.rf_[ab][12] from int to s32.
Convert tda18271_priv.tm_rfcal from unsigned int to u8.
Cast subtractions between u32 values as s32.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use temporary variables for signed calulations between unsigned values
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds a forgotten module_param macro needed to set a deemphasis of 50us.
It is the standard setting for commercial FM radio broadcasts outside the US.
Signed-off-by: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
override set_frontend to allow rf input path switching on the HVR1275
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes adds IR Rx keypress input event handling to the CX23885 module.
This change specifically only adds input handling for IR devices implemented as
v4l2_subdevices, using only the pulse width mode (for now), and only with
RC-5 remotes. The V4L-DVB infrastructure is missing too much to support RC-6
mode 6A as used in many media center remotes. The grey Hauppauge RC-5 remote
and HVR-1850 IR receiver work now.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add integrated IR subdevice interrupt and notification handling. This is in
preparation of input keypress handling changes for the cx23885 module.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change completes the v4l2_subdev implementation for IR receive for the
IR controller built into the CX23888.
This changes almost completes the IR transmit side also, but doesn't. Instead
notes in the comments describe what needs to be done for IR Tx to work in the
subdevice implementation.
The current Tx behavior is skeletal and benign. If left alone, it does nothing.
It will only ever generate a Tx interrupt on Tx init by a caller or when the
tx_write() method is called. The ISR, when called, will then disable the Tx
FIFO service interrupt.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The prior mechanism wasn't reliable with the cx23887. This new mechanism
tests correctly against cx23885, 7 and 8 based products.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the IR controller on the CX23888 to work for the HVR-1850 and in
general, the A/V core must be initialized to get the VID_CLK going.
The VID_CLK is the timing reference for the CX23888's integrated
IR controller.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The SYS and AUX PLLs need to be initialized to different values based on
the chip: CX23885, CX23887, CX23888, as each uses a different crystal
frequency: 28.6363 MHz, 25.0 MHz, 50.0 MHz.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Separate out the set_audclk_freq() function into separate functions for the
four families of cores. These cores all use slightly different sample clock
schemes and may be assuming slightly (+/- 3 Hz) different reference frequencies.
The code resuse was not worth the maintenance and testing headache of have all
chips use the same function peppered with conditional logic.
Added comments on how PLL and SRC parameters values are computed. Fixed a few
bugs related to the shared code having a large number of conditional statements.
Noted inconsistencies with FIXME in the comments.
This is done in preparation for getting the CX2388[578] PLL/clock setting logic
cleaned up for CX23888 analog video and IR (which need the VID PLL set right).
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change logic to check for various chip or core families to inline functions.
Checks for specific chips should be made against the state->id field now. This
is in preparation for chip/core specific code for setting up PLLs for the
CX2388[578] family of cores, that all run with different crystal frequencies.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add improved logic to detect the exact CX2388[578] A/V core that is being
probed. Also cleaned up detection and logging for CX2310[12], CX2583[67],
and CX2584[0123] cores and chips.
Also added code to identify a CX2388[578] A/V decoder core that is not
responding properly. Typical symptoms include registers 0x00-0xff
responding properly but all other registers returning the same value
(0x13 and 0x5 have been observed). This state will cause proper detection of
'885 vs. '887 vs. '888 to fail and the chip won't respond to get configured
properly anyway. I have no method of reseting the core to a working state at
this time; but I didn't try too hard to work one out either. The problem
likely only occurs in development. I suspect configuring the SYS PLL VCO to
oscillate too slowly (286.3 MHz?) before post divide may be the root cause,
when encountered.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change adds a skeletal implementation of a v4l2_subdevice to provide
encapsulation and abstraction of the CX23888's integrated consumer infrared
controller. This change also instantiates the cx23888_ir subdev for the
HVR-1850 which has IR hardware physically wired up to a CX23888.
The cx23888_ir subdev code is being written with long-term objectives to:
1. port it to the cx25840 module for the CX2584x, CX2583x, CX23885, & CX231xx
IR controllers
2. possibly port it to the cx18 module for the CX23418 IR controller
3. have the IR subdevice accessed abstractly in the cx23885 module, so the
driver can ignore the difference between the CX23885 and CX23888.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes corrects the ioctl() operations for both the CX2388[578] analog
video and MPEG video device nodes to properly and consistently support
VIDIOC_G_CHIP_IDENT, VIDIOC_DBG_G_REGISTER and VIDIOC_DBG_S_REGISTER ioctl()s.
This caused some ioctl() support routines to be broken out into a separate
source file.
Now v4l2-dbg can be used to manipulate CX2388[578] and CX23417 registers
including the CX2388[57] functions handled by the cx25840 module.
This was done in anticipation of developing a new v4l2_subdev for the
integrated IR controller of the CX23888.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The board support has been validated by the user, so get rid of the warning
that shows up on board load.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dmitri's patch for the Behold X7 didn't use the #define I had setup for
XC5000_RADIO_FM1, so cut over to using that instead of "1".
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the digital side of the Behold X7
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make analog audio, dvb and the remote work on a Terratec Cinergy Hybrid
XS (em2882).
Note by djh: Thanks go out fo Andrej Suligoi for his contribution in providing
and testing pretty much the exact same patch as provided by Uros. Between
the two of them, they got all the core functionality working for the device.
Cc: Andrej Suligoi <suligoi@gmail.com>
Signed-off-by: Uroš Vampl <mobile.leecher@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Seems that the reference design used for the KWorld 2800d switched from the
em2860 to em2862, so we need to add the new USB id (and the i2c hash remains
so all we need is the default em2862 id.
Thanks to Ian Young for reporting the issue and testing the fix.
Cc: Ian Young <ian@duffrecords.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove hard-coded definition of the xc5000 FM radio input, making it a
parameter passed in when doing the attach call.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set radio frequency only upon success.
Signed-off-by: David Ellingsworth <david@identd.dyndns.org>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Preserve radio state during suspend/resume.
Signed-off-by: David Ellingsworth <david@identd.dyndns.org>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ensure the radio is initialized to a consistent state.
Signed-off-by: David Ellingsworth <david@identd.dyndns.org>
Acked-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looks like eeprom IR mode byte value 0x04 means there is remote
which should be polled. Patch enables polling also in case of 0x04.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for MSI DIGIVOX mini III remote.
Thanks to Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Thanks to Roman <lists@hasnoname.de>
Cc: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Cc: Roman <lists@hasnoname.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID 1b80:c161 for KWorld PlusTV DVB-T PCI Pro Card (DVB-T PC160-T).
Thanks to Andrew Cruickshank <atcrank@gmail.com> for reporting this.
Cc: Andrew Cruickshank <atcrank@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the dib7000p:
The status is HAS_LOCK only if the demod is able to decode the TPS. Sometimes, there is a TPS data lock, even if the demod is not able to decode it (ex: no RF signal).
For the STK7770P: correct value for the charge pump
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dib7000p/dib8000: added pid filtering
dib8000: the SNR is in 10th of dB (not in dB)
dib7000p and dib8000: added the pid filtering. This feature is enabled by module option (dvb-usb module).
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This IR uses NEC protocol. In order to use, dvb_usb_dib0700_ir_proto=0
should be used.
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, dvb_usb_dib0700_ir_proto is supported only with firmwares
older than 1.2. Adds support for it also with the newer firmware.
This is needed in order to support PixelView SBTVD IR.
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Edwin Török found the following:
In function ‘memset’,
inlined from ‘ir_input_init’ at drivers/media/common/ir-functions.c:67:
/home/edwin/builds/linux-2.6/arch/x86/include/asm/string_64.h:61:
warning: call to ‘__warn_memset_zero_len’ declared with attribute
warning: memset used with constant zero length parameter; this could be
due to transposed parameters
memset(ir->ir_codes, sizeof(ir->ir_codes), 0);
In actual practice the only caller I can find happens to already have cleared
the buffer before calling ir_input_init.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial fix for this compile warning:
v4l/sh_mobile_ceu_camera.c:1789: warning: label 'exit_free_irq' defined but not used
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Address yet another regression introduced by the introduction of the zl10353
disable_i2c_gate field.
djh - I unmangled the patch which apparently got screwed up in the user's
email client.
Signed-off-by: Robert Lowery <rglowery@exemail.com.au>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When building for Sun 3:
drivers/built-in.o: In function `smscore_unregister_device':
drivers/media/dvb/siano/smscoreapi.c:723: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `smscore_register_device':
drivers/media/dvb/siano/smscoreapi.c:365: undefined reference to `dma_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The vpif_config struct was renamed to vpif_display_config, but there
is still a stray vpif_config *config pointer in vpif_display.c, preventing
it from compiling.
Remove this old duplicate pointer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set device GPIOs only once. There is no need for .dvb_gpio to select
between analog and digital because device is digital only.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit ef373189f62413803b7b816c972fc154c488cdc0 "fix use-after-free Oops,
resulting from a driver-core API change" fixed the Oops, but didn't correct
missing device object initialisation. This patch makes unloading and reloading
of soc-camera host- and client-drivers possible again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Double mutexlock found by the Linux Driver Verification project and
reported by Alexander Strakh.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Hauppauge WinTV HVR-1150 retail boards require the FORCE_TS_VALID bit
to be set in order to function properly. This change will work on the early
revisions on the board as well, but the final revision will not function
without this change.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When FORCE_TS_VALID mode is enabled, the saa713x will accept MPEG TS input
without requiring TS_VALID set high. This is required for some new boards
to function properly, due to the hardware design implementation.
The configuration is toggled within the board setup configuration. Boards
that do not have this bit set will function as before with no change.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The abs() macro has changed in 2.6.32 and returns a long instead of an
int. Fix the driver to avoid compilation warnings.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The FIX_BANDWIDTH quirk tries to work around cameras requesting the
maximum bandwidth regardless of the image size by computing a bandwidth
estimate. This works only for uncompressed frames.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Which is why I have always preferred sizeof(struct foo) over
sizeof(var).
Cc: Antti Palosaari <crope@iki.fi>
Acked-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Change vstart for CIF sensor type 1 cams
This fixes the distortion at the end of the frame, and avoids the bad frame
dropping done because of this distortion, trippling the framerate!
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a vflip quirk for the Fujitsu Amilo Xi 2528. Thanks to Evgeny for the report.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds another vflip quirk for the MSI GX700.
Thanks to John Katzmaier for reporting.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a vflip quirk for the Bruneinit laptop. Thanks to Jörg for the report
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since 2.6.32(-rc1), DVB core checks the return value of
dvb_frontend_ops.set_frontend. Now it becomes apparent that firedtv
always returned a bogus value from its set_frontend method.
CC: stable@kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This solves a problem in firedtv that has become major for Swedish DVB-T
users the last month or so. It will most likely solve issues seen by
other users as well.
If the length of an AVC message is greater than 127, the length field
should be encoded in LV mode instead of V mode. V mode can only be used
if the length is 127 or less. This patch ensures that the CA_PMT
message is always encoded in LV mode so PMT message of greater lengths
can be supported.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The s2255 driver had logic which aborted processing of a video frame
if there was no process waiting on the video buffer in question. That
simply doesn't work when the application is doing things in an
asynchronous manner. If the application went to the trouble to queue
the buffer in the first place, then the driver should always attempt
to complete it - even if the application at that moment has its
attention turned elsewhere. Applications which always blocked waiting
for I/O on the capture device would not have been affected by this.
Applications which *mostly* blocked waiting for I/O on the capture
device probably only would have been somewhat affected (frame lossage,
at a rate which goes up as the application blocks less). Applications
which never blocked on the capture device (e.g. polling only) however
would never have been able to receive any video frames, since in that
case this "is anyone waiting on this?" check on the buffer never would
have evalutated true. This patch just deletes that harmful check
against the buffer's wait queue.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: stable@kernel.org
Add support for three new Hauppauge Device USB IDs:
2040:b900
2040:b910
2040:c000
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Because the counters were not reset when starting up streaming, they would
be reused from the previous run. This can result in cases such that when the
second instance of streaming starts up, the "cnt" variable in
em28xx_audio_isocirq() can end up being negative, resulting in attempting to
write to memory before the start of runtime->dma_area (as well as having a
negative number of bytes to copy).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bttv driver function which handles switching of the video standard
(set_tvnorm() in bttv-driver.c) includes a check which can optionally
also reset the cropping configuration to a default value. It is
"optional" based on a comparison of the cropcap parameters of the
previous vs the newly requested video standard. The comparison is
being done with a memcmp(), a function which only returns a true value
if the comparison actually fails.
This if-statement appears to have been written to assume wrong
memcmp() semantics. That is, it was re-initializing the cropping
configuration only if the new video standard did NOT have different
cropcap values. That doesn't make any sense. One definitely should
reset things if the cropcap parameters are different - if there's any
comparison to made at all.
The effect of this problem was that a transition from, say, PAL to
NTSC would leave in place old cropping setup that made sense for the
PAL geometry but not for NTSC. If the application doesn't care about
cropping it also won't try to reset the cropping configuration,
resulting in an improperly cropped video frame. In the case I was
testing this actually caused black video frames to be displayed.
Another interesting effect of this bug is that if one does something
which does NOT change the video standard and this function is run,
then the cropping setup gets reset anyway - again because of the
backwards comparison. It turns out that just running anything which
merely opens and closes the video device node (e.g. v4l-info) will
cause this to happen. One can argue that simply opening the device
node and not doing anything to it should not mess with any of its
state - but because of this behavior, any TV app which does such
things (e.g. xawtv) probably therefore doesn't see the problem.
The solution is to fix the sense of the if-statement. It's easy to
see how this mistake could have been made given how memcmp() works.
The patch is therefore removal of a single "!" character from the
if-statement in set_tvnorm in bttv-driver.c.
Signed-off-by: Mike Isely <isely@pobox.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a subtle interaction in the bttv driver which can result in
fields being repeatedly processed out of order. This is a problem
specifically when running in V4L2_FIELD_ALTERNATE mode (probably the
most common case).
1. The determination of which fields are associated with which buffers
happens in videobuf, before the bttv driver gets a chance to queue the
corresponding DMA. Thus by the point when the DMA is queued for a
given buffer, the algorithm has to do the queuing based on the
buffer's already assigned field type - not based on which field is
"next" in the video stream.
2. The driver normally tries to queue both the top and bottom fields
at the same time (see bttv_irq_next_video()). It tries to sort out
top vs bottom by looking at the field type for the next 2 available
buffers and assigning them appropriately.
3. However the bttv driver *always* actually processes the top field
first. There's even an interrupt set aside for specifically
recognizing when the top field has been processed so that it can be
marked done even while the bottom field is still being DMAed.
Given all of the above, if one gets into a situation where
bttv_irq_next_video() gets entered when the first available buffer has
been pre-associated as a bottom field, then the function is going to
process the buffers out of order. That first available buffer will be
put into the bottom field slot and the buffer after that will be put
into the top field slot. Problem is, since the top field is always
processed first by the driver, then that second buffer (the one after
the first available buffer) will be the first one to be finished.
Because of the strict fifo handling of all video buffers, then that
top field won't be seen by the app until after the bottom field is
also processed. Worse still, the app will get back the
chronologically later bottom field first, *before* the top field is
received. The buffer's timestamps will even be backwards.
While not fatal to most TV apps, this behavior can subtlely degrade
userspace deinterlacing (probably will cause jitter). That's probably
why it has gone unnoticed. But it will also cause serious problems if
the app in question discards all but the latest received buffer (a
latency minimizing tactic) - causing one field to only ever be
displayed since the other is now always late. Unfortunately once you
get into this state, you're stuck this way - because having consumed
two buffers, now the next time around the "first" available buffer
will again be a bottom field and the same thing happens.
How can we get into this state? In a perfect world, where there's
always a few free buffers queued to the driver, it should be
impossible. However if something disrupts streaming, e.g. if the
userspace app can't queue free buffers fast enough for a moment due
perhaps to a CPU scheduling glitch, then the driver can get
momentarily starved and some number of fields will be dropped. That's
OK. But if an odd number of fields get dropped, then that "first"
available buffer might be the bottom field and now we're stuck...
This patch fixes that problem by deliberately only setting up a single
field for one frame if we don't get a top field as the first available
buffer. By purposely skipping the other field, then we only handle a
single buffer thus bringing things back into proper sync (i.e. top
field first) for the next frame. To do this we just drop the few
lines in bttv_irq_next_video() that attempt to set up the second
buffer when that second buffer isn't for the bottom field.
This is definitely a problem in when in V4L2_FIELD_ALTERNATE mode. In
the other modes this change either has no effect or doesn't harm
things any further anyway.
Signed-off-by: Mike Isely <isely@pobox.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The lack of #include <linux/vmalloc.h> caused a compile error on some
architectures.
Signed-off-by: HIRANO Takahito <hiranotaka@zng.info>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit b402843787 has broken again re-use of
device objects across device_register() / device_unregister() cycles. Fix
soc-camera by nullifying the struct after device_unregister().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a bug in cropping calculation, when the client is also scaling the image.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When we call gspca_frame_add, it returns a pointer to the frame passed in,
unless we call it with LAST_PACKET, when it will return a pointer to a
new frame in which to store the frame data for the next frame.
The frame pointer was not updated in stv06xx and ov518.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While having tda18271 module set with debug=17 (cal & info prints) and
cal=0 (delay calibration process until first use) - I discovered that
during the calibration process, if the frequency test for 69750000
returned a bcal of 0 (see tda18721-fe.c in tda18271_powerscan func) that
the tuner wouldn't be able to pickup any of the frequencies in the range
(all the other frequencies bands returned bcal=1). I spent some time
going over the code and the NXP's tda18271 spec (ver.4 of it i think) and
adding a lot of debug prints and walking/stepping through the calibration
process. I found that when the powerscan fails to find a frequency, the
rf calibration is not run and the default value is supposed to be used in
its place (pulled from the RF_CAL_map table) - but something was getting
goofed up there.
Now, my c coding skills are very rusty, but i think root of the problem is
a signedness issue with the math operation for calculating the rf_a1 and
rf_a2 values in tda18271_rf_tracking_filters_init func, which results in
values like 20648 for rf_a1 (when it should probably have a value like 0,
or so slightly negative that it should be zero - this bad value for rf_a1
would in turn makes the approx calc within
tda18271c2_rf_tracking_filters_correction go out of whack). The simplest
solution i found was to explicitly convert the signedness of the
denominator to avoid the implicit conversion. The values placed into the
u32 rf_freq array should never exceed about 900mhz, so i think the s32 max
value shouldn't be an issue in this case.
I've tested it out a little, and even when i get a bcal=0 with the
modified code, the default calibration value gets used, rf_a1 is zero, and
the tuner seems to lock on the stream and mythtv seems to play it fine.
Signed-off-by: Seth Barry <seth@cyberseth.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multiplication by 62500 causes an overflow in the 32 bit freq variable,
which is later divided by 1000 when using FM radio.
This patch prevents the overflow by scaling the frequency value correctly
upfront. Thanks to Henk Vergonet for spotting the problem and providing
a preliminary patch, which this changeset was based upon.
Cc: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixing kernel oops when driver attemps to load xc2028 firmware.
Note by djh: the patch contribute by Martin is a port of a fix I made during
the PCTV 340e development. It's a temporary workaround that fixes a regression
(an OOPS condition) and the real fix should be in the code that manages the
i2c master on the dib7000p. But this fix does address the immmediate
regression and should be merged upstream until we do a cleaner fix.
Signed-off-by: Martin Samek <martin@marsark.sytes.net>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
git commit db48138f6b changed by accident the
assignment of certain USB IDs to their device-specific-handlers.
Thanks to Edward Sheldrake for finding this regression
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Marton Nemeth