This just updates the firmware loading functions
to look for the appropriate firmware files for
hawaii.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The formula needs to be adjusted since there are 4 RBs
per SH rather than 2 as on previous asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The golden register settings are optimal settings for
certain registers from the hardware team.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The new HDP flush method doesn't seem to work reliably on
sDMA either, so use the old method here too.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To plug the VRAM memory leak (see previous patch for
details) we must unpin the frame buffer when disabling the
CRTC. This warrants the addition of disable function for legacy
CRTC, which puts the CRTC in DPMS-OFF state and unpins the
frame buffer if there is one associated with the CRTC.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When drm_helper_disable_unused_functions calls disable
function of the CRTC, it also sets the crtc->fb pointer
to NULL. This can later (when the mode on that CRTC is setup
again from user space) cause ***_do_set_base functions to
"think" that there is no old buffer and skip the unpinning
code. Consequently, the buffer that has been NULL-ified in
drm_helper_disable_unused_functions will never be unpinned
causing a leak in VRAM.
This patch plugs the leak by unpinning the frame buffer
in crtc_disable function.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current code writing SADs to the audio registers seems to assume
that there is at most a single SAD per audio format.
However, that is not the case. Especially for PCM it is somewhat common
for sinks to have two SADs, one for 8-channel and one for 2-channel
audio, which may have different supported sample rates (i.e. the sink
supports stereo audio at higher sample rates than multichannel audio).
Because of this, only the 2-channel SAD may be used if it appears before
the 8-channel SAD. Unless other SADs require otherwise, this may cause
the ALSA HDA driver to allow stereo playback only.
Fix the code to pick the PCM SAD with the highest number of channels,
while merging the rate masks of PCM SADs with lower amount of channels
into the additional stereo rate mask byte.
Technically there are even more cases to handle (multiple non-PCM SADs
of the same type, more than two PCM SADs with varying channel counts,
etc), but those have not actually been encountered in the field and
handling them would be non-trivial.
Example affected EDID from Onkyo TX-SR674 specifying 192kHz stereo
support and 96kHz 8-channel support (and other 8-channel compressed
formats):
00ffffffffffff003dcb010000000001
ffff0103800000780a0dc9a057479827
12484c00000001010101010101010101
010101010101011d8018711c1620582c
2500c48e2100009e011d007251d01e20
6e285500c48e2100001e000000fc0054
582d53523637342020202020000000fd
00313d0f2e08000a202020202020019b
02032f724f8504030f0e07069413121e
1d1615012f097f070f1f071707503707
503f07c0834f000066030c00ffff808c
0ad08a20e02d10103e9600c48e210000
18011d80d0721c1620102c2580c48e21
00009e011d00bc52d01e20b8285540c4
8e2100001e8c0ad090204031200c4055
00c48e210000180000000000000000a8
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Andre Heider <a.heider@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HW engineers have listened and given us again a real interrupt with
masking and status regs. Yay!
For consistency with other platforms call the #define FIFO_UNDERRUN.
Eventually we also might need to have some enable/disable functions
for bdw display interrupts, but for now open-coding seems to be good
enough.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's cache the IMR value like on other platforms. This is needed to
implement the underrun reporting since then we'll have two places that
change the same register at runtime.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The layout of the CRC registers is the same as on hsw, only the
interrupt handling has changed a bit. So trivial to wire up, yay!
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gives us hotplug, gmbus, dp aux and south errors (underrun
reporting!).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Useful for dp aux to work better. Also stop enabling the port A
hotplug event - eDP panels are expected to fire that interupt and
we're not really ready to deal with them. This is consistent with how
we handle port A on ilk-hsw.
The more important bit is that we must delay the enabling of hotplug
interrupts until all the encoders are fully set up. But we need irq
support earlier than that, hence hotplug interrupts can only be
enabled in the ->hpd_irq_setup callback.
v2: Drop the _HOTPLUG, it isn't (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Pipe underrun can't just be enabled, we need some support code like
on ilk-hsw to make this happen. So drop it for now.
- CRC error is a special mode of the CRC hardware that we don't use,
so again drop it. Real CRC support for bdw will be added later.
- All the other error bits are about faults, so rename the #define and
adjust the output.
v2: Use pipe_name as pointed out by Ville. Ville's comment was on a
previous patch, but it was easier to squash in here.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a per-pipe bit in the master irq control register, so use it.
This allows us to drop the masks for aggregate interrupt bits and be a
bit more explicit in the code. It also removes one indentation level.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The handling of the error interrupts isn't wired up at all. And it
hasn't been ever since ilk happened, so don't bother.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Early platforms use the same PCH as HSW, and to avoid triggering the
!ULT, and !HSW warnings, simply put it first in the search.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell should also use hsw_crt_get_config(). Just move the
function pointer assignment to the if HAS_DDI block we already
have there.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like on HSW, trickle feed should always be enabled on BDW.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Hold vertex data in cache until last reference
BDW-A workaround
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW-A workaround
BDW Bug #1899532
v2: WARN on when not using preliminary HW support
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This implements a workaround for PSR dealing with some vblank issue.
WaPsrDPAMaskVBlankInSRD && WaPsrDPRSUnmaskVBlankInSRD
v2: forgot to git add bogus whitespace fix
v3: Update with workaround names.
Use for_each_pipe() and CHICKEN_PIPESL_1(pipe) macro (Ville)
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
[danvet: Kill redundant IS_BDW check and remove the copious amount of
uneeded lines added.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've done insufficient testing on them thus far, so keep them disabled
until we do test.
v2: Use WARN when not enabling preliminary HW support as this should
only be disabled for that case.
v3: Rip out the now useless (and really noisy) DRM_INFO output.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is mostly what we have for HSW with the exceptions of:
no writes:
GEN6_RC1_WAKE_RATE_LIMIT
GEN6_RC6pp_WAKE_RATE_LIMIT
GEN6_RC1e_THRESHOLD
GEN6_RC6p_THRESHOLD
GEN6_RC6pp_THRESHOLD
GEN6_RP_DOWN_TIMEOUT - use 1s instead of 1.28s
Don't try to overclock, or program ring/IA frequency tables since we
don't quite have sufficient docs yet.
NOTE: These values do not reflect the changes made recently by Chris.
Since we have no evidence yet what the proper way to tweak for this
platform is, I think it is good to go, and can be optimized by Chris, or
whomever, later.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Drop spurious hunk and drop TODO - having per-platform rps
register frobbing code is in my opinion preferred, now that all the
infrastructure functions are extracted.]
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like HSW.
This means we can scan out a mode with a 300Mhz pixel clock with a depth
of 24 bits, but only a 200Mhz one with a 36bits depth.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's no longer a required workaround on BDW.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Move compile fix from a later patch to this one.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current formula we use for HSW is not what is in current docs.
However, changing to the HSW formula on my HSW does not improve power
usage, and decreases performance by about 5% in limited xonotic testing.
For gen8, until we know otherwise, or run experiments, let's use
the HSW formula - which should be the same used in the Windows driver
(and thus help make an apples-applies comparison) on gen8.
v2: Use >= 8 instead of > 7 to be consistent with all other gen
checks.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell PSR support is a superset of Haswell. With this simple
register base calculation, everything that worked on HSW for eDP PSR
should work on BDW.
Note that Broadwell provides additional PSR support. This is not
addressed at this time.
v2: Make the HAS_PSR include BDW
v3: Use the correct offset (I had incorrectly used one from my faulty
brain) (Art!)
v4: It helps if you git add
v5: Be explicit about not setting min link entry time for BDW. This
should be no functional change over v4 (Jani)
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Squash in fixup from Ben to synchronize the GT mailbox commands.
CC: Art Runyan <arthur.j.runyan@intel.com>
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell has bigger display FIFOs than Haswell. Otherwise the
two are very similar.
v2: Fix FBC WM_LP shift for BDW
v3: Rebase on top of the big Haswell wm rework.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the eDP values on platforms where port D is eDP. This doesn't
affect Haswell since it uses the same DDI buffer values for eDP and
DP.
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So treat it like Haswell.
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They're not the same as the Haswell ones.
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell has different DDI buffer translations for eDP and DP, so add
support for the missing eDP and keep Haswell the same.
A future patch addresses the suggestion from Art to check for eDP on
port D and use the eDP values there, too.
v2: Make checkpatch happy.
Reviewed-by: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Many of the DDI buffer translation values have changed for BDW.
Add new translation tables and selection between HSW and BDW.
v2: s/BUG/WARN/ to avoid breaking future GENs.
v3: Rebase on top of the hdmi translation table changes.
v4: Fix up the multiline comment while at it.
Signed-off-by: Art Runyan <arthur.j.runyan@intel.com> (v2)
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN8 also needs this workaround.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add a generic comment that we need to recheck all these w/a.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Route cursor and sprite data through the pipe CSC unit on BDW.
Primary plane data is already sent through the pipe CSC.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebased onto Paulo's MHz->kHz change.
v3: Rebased on top of the Haswell pc8+ adjustements.
v4: Use the exact 337.5MHz clock, should have been done as part of v2.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And it inherits some bits from the previous TRANS_CONF (aka PIPE_CONF
on previous gens).
v2: Rebase on to of the pipe config bpp handling rework.
v3: Rebased on top of the pipe_config->dither refactoring.
v4: Drop the read-modify-write cycle for PIPEMISC, similarly to how we
now also build up PIPECONF completely ourselves - keeping around
random stuff set by the BIOS just isn't a good idea. I've checked BDW
BSpec and we already set all relevant bits.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So you can use the panel fitter while the power well is disabled and
you also don't need to set the "pipe" bit.
v2: Rebased on top of Jesse's pfit refactor, which moved pfit state
into the pipe_config.
v3: Rebase on top of the latest Haswell/panel fitter rework, which
neatly resolves a FIXME we have in this patch here:
v4: Rebase on top of the new power domain framework.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The platforms we currently have all have LPT LP on them. As such, we
have no way to identify the new WPT PCH that will ship with Broadwell.
NOTE: For all purposes relevant to the driver that this point, LPT and
WPT are equivalent. Therefore there should be no need to actually change
this for some time.
v2: Don't assign dev_priv->num_pch_pll any more.
v3: Rebase on top of the PCH detection changes for virtualized
enviroments.
v4: Wrote commit message
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v3)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like Haswell, but with the small twist that the panel fitter for pipe A is
now also in the always-on power well.
v2: Use the new HAS_POWER_WELL macro.
v3: Rebase on top of intel_using_power_well patches.
v4: This time actually update the PFIT check correctly so that the
pipe A pfit is in the always-on domain.
v5: Rebase on top of the VGA power domain addition.
v6: Rebase on top of the new power domain infrastructure. Also pimp the commit
message a bit while at it.
v7: Use IS_BROADWELL instead of IS_GEN8 (Ville).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just make Broadwell follow the same code paths as Haswell here,
instead of running code for the even-older platforms.
v2: Shuffle around Ben's vma prep work.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebase (Paulo Zanoni)
v3: Rebase on top of num_pipes having moved to intel_device_info.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now it's just equivalent to IS_GEN8, but in the future we might
want to change that (e.g., on Gen 7 we have IS_VALLEYVIEW,
IS_IVYBRIDGE and IS_HASWELL).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was an oversight and should have been in a previous series
somewhere.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not so much that the information is terribly useful, but rather
that the gen6/7 information is completely useless.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Resolve rebase conflicts and switch to gen < 8 color for GenX
checking.
v3: Rebase on top of the address space refactoring.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PIPE_CONTROL added the high address dword. I'm not sure how the
simulator let me get away with this. I've explicitly left out all the
workarounds from Gen7 because in the minimal digging that I did, most
don't seem necessary, and the simulator doesn't complain without them
Note that BLT and BSD ring commands had already been updated previously.
Just render/pipe_control should have been broken.
v2: Squash in a fixup from Ville to follow the recent IVB PIPE_CONTROL
updates: "BDW uses the IVB PIPE_CONTROL style for specifying GTT vs.
PPGTT for the PIPE_CONTROL QW/DW write."
v3: Rebase on top of Chris' cleanup to have an explicit ring->scratch
buffer object instead of an opaque ring->private where everyone stores
the same stuff inside.
Reported-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (for the fixup)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Squash in fix from Ben: Set PPGTT batches as necessary
This fixes the regression in the last couple of days when we enabled
PPGTT.
v3: Squash in fixup to still use GTT for secure batches from Ville:
BDW doesn't have a separate secure vs. non-secure bit in
MI_BATCH_BUFFER_START. So for secure batches we have to simply
leave the PPGTT bit unset. Fortunately older generations (except
HSW) had similar limitations so execbuffer already creates a GTT
mapping for all secure batches.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Legacy PPGTT on GEN8 requires programming 4 PDP registers per ring.
Since all rings are using the same address space with the current code
the logic is simply to program all the tables we've setup for the PPGTT.
v2: Turn on PPGTT in GFX_MODE
v3: v2 was the wrong patch
v4: Resolve conflicts due to patch series reordering.
v5: Squash in fixup from Ben: Use LRI to write PDPs
The docs (and simulator seems to back up) suggest that we can only
program legacy PPGTT PDPs with LRI commands.
v6: Rebase around context differences conflicts.
v7: Use #defines for per ring PDPs. (Damien)
v8: Don't use typede'f private_t.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (up to v3 and v7)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN8 insertion is very similar to GEN6.
v2: Rebase on top of Imre's for_each_sg_page helpers.
v3: Fixup my conversion (spotted by Ville).
v4: Rebase on top of the address space refactoring.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GEN8 PPGTT range clearing is very similar to GEN6 if we assume that our
PDEs are all valid, which they should be.
v2: Rebase on top of the address space refactoring.
v3: Rebase on top of the bool use_scratch addition to the clear_range interface.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The upcoming clear and insert routines will expect that PDEs all point
to valid Page Directories. Doing that lazily doesn't really buy us
anything.
The page allocation is done regardless earlier in init so it shouldn't
hurt set the PDEs.
v2: Squash in patches to implement fixed PDE write function:
- If I had done this in the first place, the bug that's going to be
fixed in an upcoming patch would have been much easier to find.
- Use WB for PDEs.
The PAT bit is used for page size. 2ME PDEs aren't even supported in
BDW, so this was completely invalid. The solution is to make our
PDEs WB+LLC instead of the pervious WB+eLLC. As far as I can guess,
this change won't matter for performance.
Thanks to Ville for the quick correction when discussing on IRC.
v3: Return the pde type for pde encoding (Damien)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Aside from the potential size increase of the PPGTT, the primary
difference from previous hardware is the Page Directories are no longer
carved out of the Global GTT.
Note that the PDE allocation is done as a 8MB contiguous allocation,
this needs to be eventually fixed (since driver reloading will be a
pain otherwise). Also, this will be a no-go for real PPGTT support.
v2: Move vtable initialization
v3: Resolve conflicts due to patch series reordering.
v4: Rebase on top of the address space refactoring of the PPGTT
support. Drop Imre's r-b tag for v2, too outdated by now.
v5: Free the correct amount of memory, "get_order takes size not a page
count." (Imre)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW caching works differently than the previous generations. Instead of
having bits in the PTE which directly control how the page is cached,
the 3 PTE bits PWT PCD and PAT provide an index into a PAT defined by
register 0x40e0. This style of caching is functionally equivalent to how
it works on HSW and before.
v2: Tiny bikeshed as discussed on internal irc.
v3: Squash in patch from Ville to mirror the x86 PAT setup more like
in arch/x86/mm/pat.c. Primarily, the 0th index will be WB, and not
uncached.
v4: Comment for reason to not use a 64b write on the PPAT.
v5: Add a FIXME comment that the caching bits in the PAT registers
might be wrong due to doc confusion.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the PTE clarifications, the bind and clear functions can now be
added for gen8.
v2: Use for_each_sg_pages in gen8_ggtt_insert_entries.
v3: Drop dev argument to pte encode functions, upstream lost it. Also
rebase on top of the scratch page movement.
v4: Rebase on top of the new address space vfuncs.
v5: Add the bool use_scratch argument to clear_range and the bool valid argument
to the PTE encode function to follow upstream changes.
v6: Add a FIXME(BDW) about the size mismatch of the readback check
that Jon Bloomfield spotted.
v7: Squash in fixup patch from Ben for the posting read to match the
64bit ptes and so shut up the WARN.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With gen6 PTE type in place, pave the way for the new gen8 type.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Probing gen8 is similar to gen6. To make the code cleaner and more
maintainable however we can use the probe functions to split it out.
v2: Rebased on top of update gtt probe infrastructure.
v3: Rebased on top of Kenneth' Graunke's ->pte_encode refactoring.
V4: Resolve conflicts with Ben's latest ppgtt patches, also switch to
gen < 8 testing instead of gen <= 7.
v5: Resolve conflicts with address space vfunc changes in upstream.
v6: Use 39b DMA mask. At least, for this mode, it is the correct mask.
(Imre)
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the gen8 debugfs stuff I wasn't too lazy to update. We'll need more
later, I am certain.
v2: Fix up the register name in the debugfs output as suggested by
Paulo.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Reviewed-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code is more verbose than necessary for the reader's sake, hopefully
the compiler optimizes away the if.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The command to emit batch buffers has changed to address 48b addresses.
It seemed reasonable that we could still use the old instruction where
emitting 0 for length would do the right thing, but it seems to bother
the simulator when the code does that.
Now the second dword in the command has the upper 16b of the address of
the batchbuffer.
v2: Remove duplicated vfun assignment.
v3: Squash in VECS support changes from Zhao Yakui <yakui.zhao@intel.com>
v4: Make checkpatch happy.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't actually return any to userspace yet, however we can pretend
like we do now so userspace will support it when it happens.
This is just to please Chris as the code itself isn't ready for > 64b
relocations.
v2: Rebase on top of the refactored relocate_entry_gtt|cpu functions.
v3: Squash in fixup from Rafal Barbalho for 64 byte relocs using cpu
relocs and those crossing a page boundary.
v4: Squash in a fixup for the fixup from Rafael.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Barbalho, Rafael <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The interrupt handling implementation remains the same as previous
generations with the 4 types of registers, status, identity, mask, and
enable. However the layout of where the bits go have changed entirely.
To address these changes, all of the interrupt vfuncs needed special
gen8 code.
The way it works is there is a top level status register now which
informs the interrupt service routine which unit caused the interrupt,
and therefore which interrupt registers to read to process the
interrupt. For display the division is quite logical, a set of interrupt
registers for each pipe, and in addition to those, a set each for "misc"
and port.
For GT the things get a bit hairy, as seen by the code. Each of the GT
units has it's own bits defined. They all look *very similar* and
resides in 16 bits of a GT register. As an example, RCS and BCS share
register 0. To compact the code a bit, at a slight expense to
complexity, this is exactly how the code works as well. 2 structures are
added to the ring buffer so that our ring buffer interrupt handling code
knows which ring shares the interrupt registers, and a shift value (ie.
the top or bottom 16 bits of the register).
The above allows us to kept the interrupt register caching scheme, the
per interrupt enables, and the code to mask and unmask interrupts
relatively clean (again at the cost of some more complexity).
Most of the GT units mentioned above are command streamers, and so the
symmetry should work quite well for even the yet to be implemented rings
which Broadwell adds.
v2: Fixes up a couple of bugs, and is more verbose about errors in the
Broadwell interrupt handler.
v3: fix DE_MISC IER offset
v4: Simplify interrupts:
I totally misread the docs the first time I implemented interrupts, and
so this should greatly simplify the mess. Unlike GEN6, we never touch
the regular mask registers in irq_get/put.
v5: Rebased on to of recent pch hotplug setup changes.
v6: Fixup on top of moving num_pipes to intel_info.
v7: Rebased on top of Egbert Eich's hpd irq handling rework. Also
wired up ibx_hpd_irq_setup for gen8.
v8: Rebase on top of Jani's asle handling rework.
v9: Rebase on top of Ben's VECS enabling for Haswell, where he
unfortunately went OCD on the gt irq #defines. Not that they're still
not yet fully consistent:
- Used the GT_RENDER_ #defines + bdw shifts.
- Dropped the shift from the L3_PARITY stuff, seemed clearer.
- s/irq_refcount/irq_refcount.gt/
v10: Squash in VECS enabling patches and the gen8_gt_irq_handler
refactoring from Zhao Yakui <yakui.zhao@intel.com>
v11: Rebase on top of the interrupt cleanups in upstream.
v12: Rebase on top of Ben's DPF changes in upstream.
v13: Drop bdw from the HAS_L3_DPF feature flag for now, it's unclear what
exactly needs to be done. Requested by Ben.
v14: Fix the patch.
- Drop the mask of reserved bits and assorted logic, it doesn't match
the spec.
- Do the posting read inconditionally instead of commenting it out.
- Add a GEN8_MASTER_IRQ_CONTROL definition and use it.
- Fix up the GEN8_PIPE interrupt defines and give the GEN8_ prefixes -
we actually will need to use them.
- Enclose macros in do {} while (0) (checkpatch).
- Clear DE_MISC interrupt bits only after having processed them.
- Fix whitespace fail (checkpatch).
- Fix overtly long lines where appropriate (checkpatch).
- Don't use typedef'ed private_t (maintainer-scripts).
- Align the function parameter list correctly.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v4)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
bikeshed
All the BARs have the ability to grow.
v2: Pulled out the simulator workaround to a separate patch.
Rebased.
v3: Rebase onto latest vlv patches from Jesse.
v4: Rebased on top of the early stolen quirk patch from Jesse.
v5: Use the new macro names.
s/INTEL_BDW_PCI_IDS_D/INTEL_BDW_D_IDS
s/INTEL_BDW_PCI_IDS_M/INTEL_BDW_M_IDS
It's Jesse's fault for not following the convention I originally set.
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just enough to make the code not barf...
Init BDW display to look like HSW. For the simulator this should be
fine, but this will probably require more work.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Add a FIXME comment about RCS flips being untested on bdw.
Also add a note that hblank events are reserved on bdw+ in DERRMR.]
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Clock gating init is really a catch all function for registers we need
to write early in loading the driver.
Atm just the bare metal stuff we need, more will surely come.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW context sizes varies a bit.
v2: Squash in fixup for the hw context size from Ben.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Squash in "drm/i915/bdw: Add BDW to the HAS_DDI check" as
suggested by Damien.
v3: Squash in VEBOX enabling from Zhao Yakui <yakui.zhao@intel.com>
v4: Rebase on top of Jesse's patch to extract all pci ids to
include/drm/i915_pciids.h.
v4: Replace Halo by its marketing moniker Iris. Requested by Ben.
v5: Switch from info->has*ring to info->ring_mask.
v6: Add 0x16X2 variant (which is newer than this patch)
Rename to use new naming scheme (Chris)
Remove Simulator PCI ids. These snuck in during rebase (Chris)
v7: Fix poor sed job from v6
Make the desktop variants use the desktop macro (Rebase error). Notice
that this makes no functional difference - it's just confusing.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be changed once the gen8 code is fully implemented.
v2: Use ENOSYS instead of ENXIO as suggested by Chris.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow this got missed or dropped during development. The simulator
does not use forcewake, so it's entirely possible it never worked
correctly. After the mmio rework, this will end up in an OOPs, and the
system will not boot.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Use IS_GEN8 instead of IS_BROADWELL.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously we always had something hooked up to LVDS so we tried very
hard to get a mode. With the Minnowboard this is no longer the case.
If no mode can be found over DDC or the firmware we just ignore LVDS.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
For the minnowboard to work the values found in EMGD are required.
This might break Oaktrail but without hardware to test with I cannot
really tell (and do not really care).
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
This turned out to be tricky. Writing to SDVOB on the primary vdc also
writes to SDVOB on the aux vdc, but reading it back on the primary vdc
always fails. Basically we never read from the primary vdc since we
will end up trashing the aux vdc.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Since we can have SDVO on Pipe B we better check the output type instead
of pipe number for Oaktrail HDMI.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
On SDVO pipes (always Pipe B on mrst) we have to sequentially write the
aux vdc. We might be able to skip programming the primary vdc in
some/most places but we don't care about that now.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
We start off by adding SDVO limits and converting all limits to the
generic gma_limit_t stuct. Then we separate clock calculations for
LVDS and SDVO. This will be cleaned up later but keep it simple for now.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
The present code assumes that optimus is present whenever two
VGA (PCI_CLASS_DISPLAY_VGA) devices are present. This does not
seem to be the case of newer laptops with optimus, in which
case the nvidia gpu is a PCI_CLASS_DISPLAY_3D device.
Rework the logic so that we count both VGA and 3D devices,
when contemplating if optimus is present on the platform.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70208
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher