Clean up the coding style before we convert this driver to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clean up the coding style before we convert this driver to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clean up the coding style before we convert this driver to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clean up the coding style before we convert this driver to V4L2.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of some "unused variable" warnings. These were the result of
sloppiness and should not have happened; I'll go stand in the corner now.
Reported-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That makes frame rate configuration persistent.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Cafe controller doesn't do non-SMBUS I/O, so we have to use it there.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow applications to play with the gain settings.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Contrary to my earlier belief, the ov7670 is not actually an SMBUS device,
though it will pretend to be one if it's in a good mood. Unfortunately,
it's rarely in a good mood, especially on the XO 1.5. So use low-level i2c
I/O instead.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reading the clkrc register creates flaky behavior in some situations, and
we can easily track its state separately.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also provide for a longer delay after reset - the XO 1.5 needs it.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
card->driver is 15 characters and a NULL. The original code
goes past the end of the array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
card->driver is 15 characters and a NULL, the original code could
cause a buffer overflow.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Randy Dunlap <randy.dunlap@oracle.com>:
drivers/staging/cx25821/cx25821-video.c:89:struct cx25821_fmt *format_by_fourcc(unsigned int fourcc)
(not static)
conflicts with (has the same non-static name as)
drivers/media/common/saa7146_video.c:87:struct saa7146_format* format_by_fourcc(struct saa7146_dev *dev, int fourcc)
To solve, add cx25821_ prefix to the exported functions found on cx25821-video.h.
This patch were generated by this little shell/perl script:
cat drivers/staging/cx25821/cx25821-video.h|perl -ne \
'if (m/extern.* ([^\s\*]+)\(/) { $n=$1; print "s/([^\d\w_\.])$1/\\1cx25821_$1/g;\n" if (!($n =~ m/cx25821/)); }' \
>changes; for i in drivers/staging/cx25821/*.[ch]; do sed -r -f changes $i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Palash Bandyopadhyay <palash.bandyopadhyay@conexant.com>
Fixes up warnings and errors found by the checkpatch.pl tool
on cx25821-i2c.c
Signed-off-by: Olimpiu Pascariu <olimpiu.pascariu@gmail.com>
Cc: Palash Bandyopadhyay <palash.bandyopadhyay@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes up warnings and errors found by the checkpatch.pl tool on
cx25821-medusa-video.c
Signed-off-by: Olimpiu Pascariu <olimpiu.pascariu@gmail.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Cc: Palash Bandyopadhyay <palash.bandyopadhyay@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes up warnings and errors found by the checkpatch.pl tool on
cx25821-gpio.c.
Signed-off-by: Olimpiu Pascariu <olimpiu.pascariu@gmail.com>
Cc: Palash Bandyopadhyay <palash.bandyopadhyay@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes up warnings and errors found by the checkpatch.pl tool on
cx25821-core.c.
Signed-off-by: Olimpiu Pascariu <olimpiu.pascariu@gmail.com>
CC: Palash Bandyopadhyay <palash.bandyopadhyay@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes up some warnings&errors found by the checkpatch.pl script
Signed-off-by: Olimpiu Pascariu <olimpiu.pascariu@gmail.com>
CC: Palash Bandyopadhyay <palash.bandyopadhyay@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support SPI bus to v4l2. Useful for control some device with SPI bus like
hardware MPEG2 encoders and etc.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for design which has an em2863/tvp5150 and uses the standard
empia USB ID. In Sander's case, it was branded as an "Eminent model EM3705"
Thanks to Sander Van Ginkel for testing and help debugging the support.
[mchehab@redhat.com: move it to a vague card number slot (card=29)]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that I merged a wrong version of the patch or that
changeset 4d770eeb926d0bc44c0bd68d051d3d2a5568ef41 got mangled somehow:
It were missed the #else to avoid compilation troubles.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the ability to use the v4l2_ctrl_query_fill() function for the newly
introduced chroma gain control.
Also, make use of the centralized function by the one caller.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for chroma agc and gain to the saa7115 driver. This allows for
users to do manual adjustment for abnormal signal conditions.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enables the anti-alias filter, which was originally enabled for
the saa7113, but the saa7115_init_misc was trampling the value. Without this
patch, there would be visible vertical bands in the chroma.
Thanks to Andy Walls for helping test this change against other ivtv products.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rework the logic for tracking the amount of data copied to the VBI buffer, to
address problem found where the video lines are several bytes shifted to the
right (and the leading pixels in the first line rendered are garbage). This
would occur because the copy function would advance the pointer when detecting
headers, but the caller would not adjust the length actually copied.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It turns up we can reduce the starting line for the active area, which results
in more data being captured when under PAL (while the full VBI capture window
still stays properly encoded).
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase the packets per URB count from 40 to 64. I suspect that whoever was
looking at the usbsnoop captures saw "0x40" packets and mistook it for "40".
As a result of this change, I can see a 25% reduction in the number of
interrupts generated via powertop.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The hv7131d sensor code also works for the hv7131e, this patch changes
it to also recognize the hv7131e sensor id.
Tested-by: Frank Danapfel <fdanapfe@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_spca561: Add support for camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix LED control on rev12a cameras and remove the unneeded
sd_stop0 callback function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed buggy init sequence for the OV9655 sensor.
Tested with a 0c45:6288 and 0c45:62b3.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for detecting webcams that are mounted
upside down in laptops. Currently the only two known
are two MSI modesl using the 0c45:624f.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drop custom code for handling the input button in
favor of using gspca's input hanlding mechinism.
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds new capture boards Hawell HW-404M7 and HW-808M7. Those cards have 4
or 8 SAA7130 chips and for the work it only needs initialize registers.
The value of those registers were dumped under Windows using flytest.
But board haven't EEPROM.
For the first chip:
SAA7130 (0x7130, SubVenID:1131, SubDevID:0000, Rev: 01)
I2C slave devices found:
No devices
GPIO pins:
Mode : 0x00389C00
Value: 0x00016C00
Video input: 3
Audio input: Analog Line1
For other chips:
SAA7130 (0x7130, SubVenID:1131, SubDevID:0000, Rev: 01)
I2C slave devices found:
No devices
GPIO pins:
Mode : 0x00389200
Value: 0x00010000
Video input: 3
Audio input: Analog Line1
Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_ctrl_get_name(): add missing control names, and make title for
V4L2_CID_BG_COLOR consistent
V4L2_CID_AUTOBRIGHTNESS was introduced with kernel 2.6.31
V4L2_CID_BAND_STOP_FILTER was introduced with kernel 2.6.32
Signed-off-by: Frank Schaefer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
>From 9473816c446a6ca91905fc49a73732f70b5223b4 Mon Sep 17 00:00:00 2001
This is a patch to the cx25821-alsa.c file that fixes up errors and warnings found by the checkpatch.pl tool
[mchehab@redhat.com: a few adjustments on the comments to improve readability]
Signed-off-by: Olimpiu Pascariu <olimpiu.pascariu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In quickcam_messenger.c, if the NULL test on uvd is needed, then the
dereference should be after the NULL test.
In vpif_display.c, std_info is initialized to the address of a structure
field. This seems unlikely to be NULL. Test std_info->stdid instead.
In saa7134-alsa.c, the function is only called from one place, where the
chip argument has already been dereferenced. On the other hand, if it
should be kept, then card should be initialized after it.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Muralidharan Karicheri <m-karicheri2@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Get rid of the magic number 0x28c0 used in several places in the ivtv and
ivtvfb driver and define the register address to a meaningful name.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changing the decoder video standard just prior to, or during, the output of
the lower field may result in a hard system lock. To avoid this, try to ensure
the firmware call occurs only during the first 100 lines of the top field.
(Minor comment addition and a line break added Andy Walls <awalls@radix.net>.)
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a guess at the proper configuration for component video on the Leadtek
PVR2100 and DVR3100 H.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some variants of the ASUS TV-FM 7135 are handled as the ASUSTeK P7131
Analog (card=146). However, by the time we find out, some
card-specific initialization is missed. In particular, the fact that
the IR is GPIO-based. Set it when we change the card type, and run
saa7134_input_init1().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Yet another naming replace magic thanks to perl scripts. This time, it
is done with:
cat tm6000-regs.h |perl -ne 'if (m/(TM6010_REQ[^\s]+)\s+0x([a-f0-9]+)\,
0x([a-f0-9]+)/) { $name="$1"; $req=$2; $val=$3; printf
"s/REQ_${req}_SET_GET_USBREG, 0x[0]*$3,/$1,/\n" }' >a; for i in tm*.c;
do sed -f a $i >b && mv b $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After looking at the "magic" registers, it is clear that usb registers
belong to request 5.
Replace them with this script:
cat /tmp/reg3 |perl -ne 'if (m/define (TM6000_U_)([^\s]+)\s+0x([A-F0-9].)/) { \
$name=$2; $val=$3; printf "s,$1$2,TM6010_REQ05_R%s_%s,g\n", $val, $name; }' >a;
sed -f a tm6000-regs.h >b; mv b tm6000-regs.h
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using magic pairs of req/reg, replace them by the defined
values.
This patch were generated by the following script:
cat tm6000-regs.h |perl -ne 'if (m/(TM6010_REQ[^\s]+)\s+0x([a-f0-9]+)\,
0x([a-f0-9]+)/) { $name="$1"; $req=$2; $val=$3; printf
"s/REQ_${req}_SET_GET_AVREG[_BIT]*, 0x[0]*$3,/$1,/\n" }' >a; for i in
tm*.c; do sed -f a $i >b && mv b $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use a pair Req/Reg for all registers at req07 and req08 groups. This
makes easier to replace them at the code with a script and helps to
avoid using the wrong req with some register.
This change were generated by this script:
if (m/^(\#define TM6010_REQ)([0-9].)([^\s]+)(\s+)0x([A-F0-9].)/) {
$name="$1$2$3"; $sp=$4; $req=$2; $val=$5; $val=~tr/A-F/a-f/; printf
"$name%s0x%s, 0x%s\n", $sp, $req, $val; } else { print $_ }
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According with the original patch that added the register names, those
are related to tm6010, so name it properly as such. Also, clearly
indicates when a register belongs to Request 0x08 and add its register
value at the name. This makes easier to double check if the proper
register is used along the driver.
This patch were made with the help of this simple perl script, applied
over the definitions of the last register groups:
if (m/define (TM6000_)([^\s]+)\s+0x([A-F0-9].)/) { $name=$2;
$val=$3; printf "s,$1$2,TM6010_REQ08_R%s_%s,g\n", $val, $name; }
And were manually adjusted to fix a few minor issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According with the original patch that added the register names, those
are related to tm6010, so name it properly as such. Also, clearly
indicates when a register belongs to Request 0x07 and add its register
value at the name. This makes easier to double check if the proper
register is used along the driver.
This patch were made with the help of this simple perl script:
if (m/define (TM6000_)([^\s]+)\s+0x([A-F0-9].)/) { $name=$2; $val=$3;
printf "s,$1$2,TM6010_REQ07_R%s_%s,g\n", $val, $name; }
And were manually adjusted to fix a few minor issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some DVB USB devices use a separate endpoint for responses to control
messages sent with bulk transfers via the generic_bulk_ctrl_endpoint.
When generic_bulk_ctrl_endpoint_response is set, it will be used instead
of the generic_bulk_ctrl_endpoint when reading usb responses in the
dvb_usb_generic_rw helper function.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Reviewed-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, both driver and keytable names are exported to userspace. This
will help userspace to decide when a table need to be replaced
by another one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change the ir-sysfs approach to create irrcv0 as a device, instead of
using class_dev. Also, change the way input is registered, in order
to make its parent to be the irrcv device.
Due to this change, now the event device is created under
/sys/class/ir/irrcv class:
/sys/class/irrcv/irrcv0/
|-- current_protocol
|-- device -> ../../../1-3
|-- input9
| |-- capabilities
| | |-- abs
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that setting this options to 50Hz can reduce the framerate, so it is
still disabled (60Hz) by default.
Signed-off-by: Mosalam Ebrahimi <m.ebrahimi@ieee.org>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Indent with tabs, not with spaces, nor with mixed style.
* Less indentation for controls index comments.
* Use lowercase hex digits.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also set default values unconditionally, for readability.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Adjust comments for sharpness control
* Set default value unconditionally, for readability
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set only the needed bits for AWB, and enable it by default.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Document that even if the state is a u8 value, both MSB and LSB are set
as sd->exposure represents half of the value we are going to set into
registers.
Skip setting exposure when AEC is enabled.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This also makes manual exposure actually work: it never worked before
because AEC was always enabled.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* Use 'agc' instead of 'autogain' in the code so to align the naming
as in AEC/AWB.
* Tweak brightness and contrast default values.
* Fix setting/resetting registers values for AGC.
* Set actual gain back when disabling AGC.
* Skip setting GAIN register when AGC is enabled.
* Enable AGC by default.
Note that as Auto Gain Control is now enabled by default, if you are
using the driver for visual computing applications you might need to
disable it explicitly in your software.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hue control doesn't work and the sensor datasheet is not clear about how
to set hue properly.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove Blue/Red Channel Target Value, they are meant for Black Level
Calibration but it is not completely clear how to use them.
Signed-off-by: Max Thrun <bear24rw@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The region set by the call to memset is immediately overwritten by the
subsequent call to memcpy.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,e3,e4;
@@
- memset(e1,e2,e3);
memcpy(e1,e4,e3);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Oliver Endriss <o.endriss@gmx.de> pointed out:
Imho not a good idea, as the frontend thread calls
- fe->ops.tuner_ops.init
- fe->ops.tuner_ops.sleep
If you remove fe->ops.i2c_gate_ctrl, init and sleep will fail,
because gate_ctrl was never called...
--
Signed-off-by: Manu Abraham <manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Remove a redundant exported gate control function
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also add in some more device ID's
Signed-off-by: Oleg Roitburd <oroitburd@gmail.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the change that stops the CX23415/6 firmware-intiiated secondary stream
appears to fix the temporal filter, it's now fully re-enabled for all capture
resolutions.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a capture is started, the firmware also appears to start a secondary
stream. Unless this secondary stream is also stopped, the encoder will remain
active and not reinitialise for the next capture. Unfortunately, setting up
the video source can glitch the encoder and result in undesirable effects that
this initialisation will clear.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Combine the two 150 ms delays into a single 300 ms delay. Ian Armstrong has
noted that the delay between CX2341X_ENC_INITIALIZE_INPUT and
CX2341X_ENC_START_CAPTURE can cause problems if the temporal filter is allowed
to be enabled.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
IRQ from CAM disabled by default. In some environment enabled IRQ can cause of
machine freeze.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID 1b80:e39a for KWorld TV Stick II (395UR).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add USB ID 1b80:e383 for KWorld USB DVB-T Stick Mobile (UB383-T).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
adds hardware frame skipping using VIDIOC_S_PARM ioctl.
adds support for VIDIOC_ENUM_FRAMEINTERVALS.
Signed-off-by: Dean Anderson <dean@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the local functions static. Note that the function command_setlights() is
currently not called from anywhere.
This will remove the following sparse warnings (see "make C=1"):
* symbol 'command_setformat' was not declared. Should it be static?
* symbol 'command_setcolourparams' was not declared. Should it be static?
* symbol 'command_setapcor' was not declared. Should it be static?
* symbol 'command_setvloffset' was not declared. Should it be static?
* symbol 'command_setexposure' was not declared. Should it be static?
* symbol 'command_setcolourbalance' was not declared. Should it be static?
* symbol 'command_setcompressiontarget' was not declared. Should it be static?
* symbol 'command_setyuvtresh' was not declared. Should it be static?
* symbol 'command_setcompressionparams' was not declared. Should it be static?
* symbol 'command_setcompression' was not declared. Should it be static?
* symbol 'command_setsensorfps' was not declared. Should it be static?
* symbol 'command_setflickerctrl' was not declared. Should it be static?
* symbol 'command_setecptiming' was not declared. Should it be static?
* symbol 'command_pause' was not declared. Should it be static?
* symbol 'command_resume' was not declared. Should it be static?
* symbol 'command_setlights' was not declared. Should it be static?
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil