On a mx28 board, running "aplay -l" and "arecord -l" results in the following:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: Playback sgtl5000-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: Capture sgtl5000-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: Playback sgtl5000-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: Capture sgtl5000-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
,which is not correct because we got a capture device listed in aplay and a
playback device listed in arecord.
On mx28 there are two serial audio interface ports (SAIF0 and SAIF1) and each
one of them are unidirectional.
Allow to specify a dai link as 'playback_only' or 'capture_only', which suits
well for this case.
After this change we can correctly report the capabilities as follows:
$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: HiFi Playback sgtl5000-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: HiFi Capture sgtl5000-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
Also tested playback and capture on the mx28evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SAIF driver is a clock provider so specifically needs the common
clock implementedation.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Mostly the mxs system design uses saif0 mclk output as the clock source
of codec. Since the mclk is implemented as a general divider with the
saif clk as the parent clock, let's register the mclk as a basic
clk-divider to common clock framework. Then with it being a clock
provdier, clk_get() call in codec driver probe function will just work.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
With mxs-dma converted to generic DMA bindings, let's move mxs-pcm to
use it by removing flages SND_DMAENGINE_PCM_FLAG_NO_DT and
SND_DMAENGINE_PCM_FLAG_COMPAT. As the result, those mxs custom dma
params code can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.
So remove devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It makes no sense to hardcode the I2C bus into the codec_name field.
cpu_dai_name and platform_name are also overwritten later in
mxs_sgtl5000_probe_dt().
So remove the three fields, as mxs platform is dt-only platform.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Variable 'ret' is not needed here, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mostly many small changes spread as seen in diffstat in sound/*
directory by this update. A significant change in the subsystem level
is the introduction of snd_soc_component, which will help more generic
handling of SoC and off-SoC components.
Also, snd_BUG_ON() macro is enabled unconditionally now due to its
misuses, so people might hit kernel warnings (it's a good thing for
us).
- compress-offload: support for capture by Charles Keepax
- HD-audio: codec delay support by Dylan Reid
- HD-audio: improvements/fixes in generic parser: better headphone mic
and headset mic support, jack_modes hint consolidation, proper beep
attach/detachment, generalized power filter controls by David
Henningsson, et al
- HD-audio: Improved management of HDMI codec pins/converters
- HD-audio: Better pin/DAC assignment for VIA codecs
- HD-audio: Haswell HDMI workarounds
- HD-audio: ALC268 codec support, a few new quirks for Chromebooks
- USB: regression fixes: USB-MIDI autopm fix, the recent ISO latency
fix by Clemens Ladisch
- USB: support for DSD formats by Daniel Mack
- USB: A few UAC2 device endian/cock fixes by Eldad Zack
- USB: quirks for Emu 192kHz support, Novation Twitch DJ controller,
Yamaha THRxx devices
- HDSPM: updates for TCO controls by Adrian Knoth
- ASoC: Add a snd_soc_component object type for generic handling of
SoC and off-SoC components by Kuninori Morimoto,
- dmaengine: a large set of cleanups and conversions by Lars-Peter
Clausen
- ASoC DAPM: performance optimizations from Ryo Tsutsui
- ASoC DAPM: support for mixer control sharing by Stephen Warren
- ASoC: multiplatform ARM cleanups from Arnd Bergmann
- ASoC: new codec drivers for AK5385 and TAS5086 from Daniel Mack
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=sYiI
-----END PGP SIGNATURE-----
Merge tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Mostly many small changes spread as seen in diffstat in sound/*
directory by this update. A significant change in the subsystem level
is the introduction of snd_soc_component, which will help more generic
handling of SoC and off-SoC components.
Also, snd_BUG_ON() macro is enabled unconditionally now due to its
misuses, so people might hit kernel warnings (it's a good thing for
us).
- compress-offload: support for capture by Charles Keepax
- HD-audio: codec delay support by Dylan Reid
- HD-audio: improvements/fixes in generic parser: better headphone
mic and headset mic support, jack_modes hint consolidation, proper
beep attach/detachment, generalized power filter controls by David
Henningsson, et al
- HD-audio: Improved management of HDMI codec pins/converters
- HD-audio: Better pin/DAC assignment for VIA codecs
- HD-audio: Haswell HDMI workarounds
- HD-audio: ALC268 codec support, a few new quirks for Chromebooks
- USB: regression fixes: USB-MIDI autopm fix, the recent ISO latency
fix by Clemens Ladisch
- USB: support for DSD formats by Daniel Mack
- USB: A few UAC2 device endian/cock fixes by Eldad Zack
- USB: quirks for Emu 192kHz support, Novation Twitch DJ controller,
Yamaha THRxx devices
- HDSPM: updates for TCO controls by Adrian Knoth
- ASoC: Add a snd_soc_component object type for generic handling of
SoC and off-SoC components by Kuninori Morimoto,
- dmaengine: a large set of cleanups and conversions by Lars-Peter
Clausen
- ASoC DAPM: performance optimizations from Ryo Tsutsui
- ASoC DAPM: support for mixer control sharing by Stephen Warren
- ASoC: multiplatform ARM cleanups from Arnd Bergmann
- ASoC: new codec drivers for AK5385 and TAS5086 from Daniel Mack"
* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (315 commits)
ALSA: usb-audio: caiaq: fix endianness bug in snd_usb_caiaq_maschine_dispatch
ALSA: asihpi: add format support check in snd_card_asihpi_capture_formats
ALSA: pcm_format_to_bits strong-typed conversion
ALSA: compress: fix the states to check for allowing read
ALSA: hda - Move Thinkpad X220 to use auto parser
ALSA: USB: adjust for changed 3.8 USB API
ALSA: usb - Avoid unnecessary sample rate changes on USB 2.0 clock sources
sound: oss/dmabuf: use dma_map_single
ALSA: ali5451: use mdelay instead of large udelay constants
ALSA: hda - Add the support for ALC286 codec
ALSA: usb-audio: USB quirk for Yamaha THR10C
ALSA: usb-audio: USB quirk for Yamaha THR5A
ALSA: usb-audio: USB quirk for Yamaha THR10
ALSA: usb-audio: Fix autopm error during probing
ALSA: snd-usb: try harder to find USB_DT_CS_ENDPOINT
ALSA: sound kconfig typo
ALSA: emu10k1: Fix dock firmware loading
ASoC: ux500: forward declare msp_i2s_platform_data
ASoC: davinci-mcasp: Add Support BCLK-to-LRCLK ratio for TDM modes
ASoC: davinci-pcm, davinci-mcasp: Clean up active_serializers
...
Use the generic dmaengine PCM driver instead of a custom implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows us to access the DAI DMA data when we create the PCM. We'll use
this when converting mxs to generic DMA engine PCM driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MXS SAIF is only half-duplex so set the SNDRV_PCM_INFO_HALF_DUPLEX flag for
the PCM in order to prevent playback and capture from running at the same time.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Refactor the dmaengine PCM library to allow the DMA channel to be requested
before opening a PCM substream. snd_dmaengine_pcm_open() now expects a DMA
channel instead of a filter function and filter parameter as its parameters.
snd_dmaengine_pcm_close() is updated to not release the DMA channel. This allows
a dmaengine based PCM driver to request its channels before the substream is
opened.
The patch also introduces two new functions, snd_dmaengine_pcm_open_request_chan()
and snd_dmaengine_pcm_close_release_chan(), which have the same signature and
behaviour of the old snd_dmaengine_pcm_{open,close}() and internally use the new
variants of these functions. All users of snd_dmaengine_pcm_{open,close}() are
updated to use snd_dmaengine_pcm_open_request_chan() and
snd_dmaengine_pcm_close_release_chan().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The header <mach/hardware.h> is not needed at all, and <mach/mxs.h> is
needed only for macros MXS_SET_ADDR and MXS_CLR_ADDR. Define the macros
and remove the mach header inclusions.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the mxs_dma_data struct, which gets passed to the dmaengine driver, is
allocated in the pcm driver's open callback. The mxs_dma_data struct has exactly
one field which is initialized from the the same field in the mxs_pcm_dma_params
struct. The mxs_pcm_dma_params struct gets passed to the pcm driver from the dai
driver. Instead of taking this indirection embed the mxs_dma_data struct
directly in the mxs_pcm_dma_params struct. This allows us to simplify the pcm
driver quite a bit, since we don't have to care about memory managing the
mxs_dma_data struct anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
saif->id and saif->master_id are unsigned, so they can not be negative.
Fix the following warning when building with W=1 option:
sound/soc/mxs/mxs-saif.c: In function 'mxs_saif_probe':
sound/soc/mxs/mxs-saif.c:676:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
sound/soc/mxs/mxs-saif.c:688:3: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
sound/soc/mxs/mxs-saif.c:692:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Use a signed variable 'ret' to handle the error values.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All MXS users have been converted to device tree and the board files have been
removed.
No need to keep platform data in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Playing 24-bit format file leads to channel swap on mx28 and the reason is that
the current driver performs one write/read to/from the SAIF_DATA register to
trigger the transfer.
This approach works fine for S16_LE case because SAIF_DATA is a 32-bit register
and thus is capable of storing the 16-bit left and right channels, but for the
S24_LE case it can only store one channel, so in order to not lose the FIFO sync
an extra read/write is needed.
Reported-by: Dan Winner <DWinner@tc-helicon.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Dan Winner <DWinner@tc-helicon.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SND_SOC_MXS_SGTL5000 is used on MXS boards, so fix the SoC family name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using devm_clk_get can make the code simpler and smaller.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set an initial clock rate for the saif internal logic to work
properly. This is important when working in EXTMASTER mode that
uses the other saif's BITCLK&LRCLK but it still needs a basic
clock which should be fast enough for the internal logic.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently we directly call a clock_enable in trigger function without
a clk_prepare as pair first.
This will cause system hang immediately when run capture because
the clock was not prepared(playback does not hang because the clock was
prepared already by get_mclk before), a warning message in clock framework
may cause a deadlock to reclaim clock lock (see: pl011_console_write).
Here we prepare clock first in hw_param, then enable it in trigger
function to guarantee the balance.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the sound dmaengine pcm helper functions implement the pcm_pointer
callback by trying to count the number of elapsed periods. This is done by
advancing the stream position in the dmaengine callback by one period.
Unfortunately there is no guarantee that the callback will be called for each
elapsed period. It may be possible that under high system load it is only called
once for multiple elapsed periods. This patch renames the current implementation
and documents its shortcomings and that it should not be used anymore in new
drivers.
The next patch will introduce a new snd_dmaengine_pcm_pointer which will be
implemented based on querying the current stream position from the dma device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Prior to this patch, the CPU side of a DAI link was specified using a
single name. Often, this was the result of calling dev_name() on the
device providing the DAI, but in the case of a CPU DAI driver that
provided multiple DAIs, it needed to mix together both the device name
and some device-relative name, in order to form a single globally unique
name.
However, the CODEC side of the DAI link was specified using separate
fields for device (name or OF node) and device-relative DAI name.
This patch allows the CPU side of a DAI link to be specified in the same
way as the CODEC side, separating concepts of device and device-relative
DAI name.
I believe this will be important in multi-codec and/or dynamic PCM
scenarios, where a single CPU driver provides multiple DAIs, while also
booting using device tree, with accompanying desire not to hard-code the
CPU side device's name into the original .cpu_dai_name field.
Ideally, both the CPU DAI and CODEC DAI loops in soc_bind_dai_link()
would now be identical. However, two things prevent that at present:
1) The need to save rtd->codec for the CODEC side, which means we have
to search for the CODEC explicitly, and not just the CODEC side DAI.
2) Since we know the CODEC side DAI is part of a codec, and not just
a standalone DAI, it's slightly more efficient to convert .codec_name/
.codec_of_node into a codec first, and then compare each DAI's .codec
field, since this avoids strcmp() on each DAI's CODEC's name within
the loop.
However, the two loops are essentially semantically equivalent.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten
for the better support of "implicit feedback". If anything about USB
got broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up immediately
at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital links
between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid the accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal routing
through components with tight sequencing and formatting constraints
within their internal paths or where there are multiple components
connected with CPU managed DMA controllers inside the SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like digital
basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124, Texas
Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be
sent slightly later as partly depending on the changes of DRM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=+JSm
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten for
the better support of "implicit feedback". If anything about USB got
broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up
immediately at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital
links between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal
routing through components with tight sequencing and formatting
constraints within their internal paths or where there are multiple
components connected with CPU managed DMA controllers inside the
SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like
digital basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124,
Texas Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be sent
slightly later as partly depending on the changes of DRM."
Fix up conflicts in regmap (due to duplicate patches, with some further
updates then having already come in from the regmap tree). Also some
fairly trivial context conflicts in the imx and mcx soc drivers.
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (280 commits)
ALSA: snd-usb: fix stream info output in /proc
ALSA: pcm - Add proper state checks to snd_pcm_drain()
ALSA: sh: Fix up namespace collision in sh_dac_audio.
ALSA: hda/realtek - Fix unused variable compile warning
ASoC: sh: fsi: enable chip specific data transfer mode
ASoC: sh: fsi: call fsi_hw_startup/shutdown from fsi_dai_trigger()
ASoC: sh: fsi: use same format for IN/OUT
ASoC: sh: fsi: add fsi_version() and removed meaningless version check
ASoC: sh: fsi: use register field macro name on IN/OUT_DMAC
ASoC: tegra: Add machine driver for WM8753 codec
ALSA: hda - Fix possible races of accesses to connection list array
ASoC: OMAP: HDMI: Introduce codec
ARM: mx31_3ds: Add sound support
ASoC: imx-mc13783 cleanup
mx31moboard: Add sound support
ASoC: mc13783 codec cleanups
ASoC: add imx-mc13783 sound support
ASoC: Add mc13783 codec
mfd: mc13xxx: add codec platform data
ASoC: don't flip master of DT-instantiated DAI links
...
Add device tree probe for mxs-sgtl5000 machine driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add device tree probe for mxs-saif driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Same as the commit 518de86 (ASoC: tegra: register 'platform' from DAIs,
get rid of pdev), it makes mxs-pcm not a platform_driver but helper to
register "platform", so that the platform_device for mxs-pcm can be
saved completely.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Artem's cleanup of the MTD API continues apace.
Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others.
More work on DiskOnChip G3, new driver for DiskOnChip G4.
Clean up debug/warning printks in JFFS2 to use pr_<level>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk92K6UACgkQdwG7hYl686NrMACfWQJRWasR78MWKfkT2vWZwTFJ
X5AAoKiSYO2pfo5gWJGOAahNC1zUqMX0
=i3Vb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
Move the header to a more common place.
The mxs dma engine is not only used in mx23/mx28, but also used
in mx50/mx6q. It will also be used in the future chips.
Rename it to mxs-dma.h, and create a new folder include/linux/fsl/ to
store the Freescale's header files.
change mxs-dma driver, mxs-mmc driver, gpmi-nand driver, mxs-saif driver
to the new header file.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Request the DMA channel in the PCM open callback instead of the hwparams
callback, this allows us to let open fail if no dma channel is available. This
also fixes a bug where the channel will be requested multiple times if hwparams
is called multiple times.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SND_PCM is already selected by SND_SOC, there is no need for
SND_IMX_SOC and SND_MXS_SOC to select it again.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown